Artifact quantification of venous stents in the MRI environment: Differences between braided and laser-cut designs

PurposeTo quantify B₀- and B₁-induced imaging artifacts of braided venous stents and to compare the artifacts to a set of laser-cut stents used in venous interventions.MethodsThree prototypes of braided venous stents with different geometries were tested in vitro. B₀ field distortion maps were measured via the frequency shift $\mathrm{\Delta }f$ using multi-echo imaging. B₁ distortions were quantified using the double angle method. The relative amplitudes $B_1^{\mathit{rel}}$ were calculated to compare the intraluminal alteration of B₁. Measurements were repeated with the stents in three different orientations: parallel, diagonal and orthogonal to B₀.ResultsAt 1.5 T, the braided stents induced a maximum frequency shift of $\left|\mathrm{\Delta }f\left(\mathit{x}\right)\right|<100\mathrm{H}\mathrm{z}$. Signal voids were limited to a distance of 2 mm to the stent walls at an echo time of 3 ms. No substantial difference in the B₀ field distortions was seen between laser-cut and braided venous stents. $B_1^{\mathit{rel}}$ maps showed strongly varying distortion patterns in the braided stents with the mean intraluminal $B_1^{\mathit{rel}}$ ranging from $\left(63\pm 18\right)\%$ in prototype 1 to $\left(98\pm 38\right)\%$ in prototype 2. Compared to laser-cut stents the braided stents showed a 5 to 9 times higher coefficient of variation of the intraluminal $B_1^{\mathit{rel}}$.ConclusionBraided venous stent prototypes allow for MR imaging of the intraluminal area without substantial signal voids due to B₀-induced artifacts. Whereas B₁ is attenuated homogeneously in laser-cut stents, the B₁ distortion in braided stents is more inhomogeneous and shows areas with enhanced amplitude. This could potentially be used in braided stent designs for intraluminal signal amplification.     

A microdosimetric analysis of the interactions of mono-energetic neutrons with human tissue

Nuclear reactions induced during high-energy radiotherapy produce secondary neutrons that, due to their carcinogenic potential, constitute an important risk for the development of iatrogenic cancer. Experimental and epidemiological findings indicate a marked energy dependence of neutron relative biological effectiveness (RBE) for carcinogenesis, but little is reported on its physical basis. While the exact mechanism of radiation carcinogenesis is yet to be fully elucidated, numerical microdosimetry can be used to predict the biological consequences of a given irradiation based on its microscopic pattern of energy depositions. Building on recent studies, this work investigated the physics underlying neutron RBE by using the microdosimetric quantity dose-mean lineal energy $\left({\bar{y}}_D\right)$ as a proxy. A simulation pipeline was constructed to explicitly calculate the ${\bar{y}}_D$ of radiation fields that consisted of (i) the open source Monte Carlo toolkit Geant4, (ii) its radiobiological extension Geant4-DNA, and (iii) a weighted track-sampling algorithm. This approach was used to study mono-energetic neutrons with initial kinetic energies between 1 eV and 10 MeV at multiple depths in a tissue-equivalent phantom. Spherical sampling volumes with diameters between 2 nm and 1 $\mathrm{\mu }$m were considered. To obtain a measure of RBE, the neutron ${\bar{y}}_D$ values were divided by those of 250 keV X-rays that were calculated in the same way. Qualitative agreement was found with published radiation protection factors and simulation data, allowing for the dependencies of neutron RBE on depth and energy to be discussed in the context of the neutron interaction cross sections and secondary particle distributions in human tissue.     

Penicillium rubens germination on desiccated and nutrient-depleted conditions depends on the water activity during sporogenesis

Fungal growth often appears in a surrounding where water and nutrients are scarce. The impact of this environment during sporogenesis on subsequent growth is often neglected.This study investigates the effect of water availability during sporogenesis on subsequent early growth. Therefore, a carbon-depleted substrate was constructed. Humidity is then the only parameter of interest. The water conditions during sporogenesis, and during subsequent growth, were varied. This is a stressing environment: no carbon source is present, and water provided solely via the vapour.The lag time, $t_l$, and initial growth rate, ${\mu }_{fp}$, of the germ tubes were monitored.The effect of $a_w$ history on germination and initial growth depends on the $RH$ of the environment. Only at low $RH$ do spores produced at low $a_w$ have a smaller $t_l$ and higher ${\mu }_{fp}$ compared to those grown at high $a_w$. This result was remarkably pronounced when the substrate was also made hydrophobic: growth only occurred when spores were developed at low $a_w$ and placed in high $RH$.Spores grown on lowered $a_w$ attract more water. It is hypothesized that this attraction affects subsequent growth behaviour, and is the reason why growth on hydrophobic glass only prevails in the condition of high $RH$ and lowered $a_w$ history.We demonstrate the influence of cultivation conditions on germination, which becomes more pronounced in a more desiccated environment.     

The effect of tube focal spot size and acquisition mode on task-based image quality performance of a GE revolution HD dual energy CT scanner

PurposeTo assess the task-based performance of images obtained under different focal spot size and acquisition mode on a dual-energy CT scanner.MethodsAxial CT image series of the Catphan phantom were obtained using a tube focus at different sizes. Acquisitions were performed in standard single-energy, high resolution (HR) and dual-energy modes. Images were reconstructed using conventional and high definition (HD) kernels. Task-based transfer function at the 50% level (TTF_50%) for teflon, delrin, low density polyethylene (LDPE) and acrylic, as well as image noise and noise texture, were assessed across all focal spots and acquisition modes using Noise Power Spectrum (NPS) analysis. A non-prewhitening mathematical observer model was used to calculate detectability index ($d_{\mathit{NPW}}^{\prime }$).ResultsTTF_50% degraded with increasing focal spot size. TTF_50% ranged from 0.67 mm⁻¹ for teflon to 0.25 mm⁻¹ for acrylic. For standard kernel, image noise and NPS-determined average spatial frequency were 8.3 HU and 0.29 mm⁻¹, respectively in single-energy, 12.0 HU and 0.37 mm⁻¹ in HR, and 7.9 HU and 0.26 mm⁻¹ in dual-energy mode. For standard kernel, $d_{\mathit{NPW}}^{\prime }$ was 61 in single-energy and HR mode and reduced to 56 in dual-energy mode.ConclusionsThe task-based image quality assessment metrics have shown that spatial resolution is higher for higher image contrast materials and detectability is higher in the standard single-energy mode compared to HR and dual-energy mode. The results of the current study provide CT operators the required knowledge to characterize their CT system towards the optimization of its clinical performance.