The effect of vastus medialis forces on patello-femoral contact: a model-based study

A mathematical model of the patello-femoral joint was introduced to investigate the impact of the vastus medialis (longus, obliquus) forces on the lateral contact force levels. In the model, the quadriceps were represented as five separate forces: vastus lateralis, vastus intermedius, rectus femoris, vastus medialis longus (VML), and obliquus (VMO). By varying the relative force generation ratios of the quadriceps heads, the patello-femoral contact forces were estimated. We sought to analytically determine the range of forces in the VMO and VML that cause a reduction or an increase of lateral contact forces, often the cause of patello-femoral pain. Our results indicated that increased contact forces are more dependent on combinations of muscle forces than solely VMO weakness. Moreover, our simulation data showed that the contact force levels are also highly dependent on the knee flexion angle. These findings suggest that training targeted to reduce contact forces through certain joint angles could actually result in a significant increase of the contact forces through other joint angles.     

Kinematic, kinetic and EMG patterns during downward squatting.

The aim of this study was to investigate the kinematic, kinetic, and electromyographic pattern before, during and after downward squatting when the trunk movement is restricted in the sagittal plane. Eight healthy subjects performed downward squatting at two different positions, semisquatting (40 degrees knee flexion) and half squatting (70 degrees knee flexion). Electromyographic responses of the vastus medialis oblique, vastus medialis longus, rectus femoris, vastus lateralis, biceps femoris, semitendineous, gastrocnemius lateralis, and tibialis anterior were recorded. The kinematics of the major joints were reconstructed using an optoelectronic system. The center of pressure (COP) was obtained using data collected from one force plate, and the ankle and knee joint torques were calculated using inverse dynamics. In the upright position there were small changes in the COP and in the knee and ankle joint torques. The tibialis anterior provoked the disruption of this upright position initiating the squat. During the acceleration phase of the squat the COP moved posteriorly, the knee joint torque remained in flexion and there was no measurable muscle activation. As the body went into the deceleration phase, the knee joint torque increased towards extension with major muscle activities being observed in the four heads of the quadriceps. Understanding these kinematic, kinetic and EMG strategies before, during and after the squat is expected to be beneficial to practitioners for utilizing squatting as a task for improving motor function.     

Effect of knee joint flexion and femur rotation on retropatellar contact of the human knee joint]

The aim of the present study was to evaluate retropatellar contact characteristics at different angles of flexion of the knee joint. To this end, 6 cadaveric legs were examined using pressure sensitive film (Fuji Prescale type "super low") at angles of flexion of 45 degrees, 60 degrees, 90 degrees and 120 degrees both in neutral rotation and 10 degrees internal and external rotation of the femur in the same knee joints. A force of 140 N was applied to both the vastus medialis and lateralis, and a comparison made with a medially and a laterally dominating muscle force. The contact areas decreased with increasing angles of flexion. The medially dominating muscle traction increased the contact area. Comparison between internal and external rotation revealed a decrease in contact area on internal rotation. The pressure measurements were comparable in all loading situations. Comparison between neutral and medial traction revealed significant differences in contact area, pressure and force. The influence of femoral rotation showed no significant difference. A comparison of the different angles of flexion revealed only few significant differences. To prevent the development of retropatellar arthrosis, maximum contact areas are necessary. The study has shown an advantage for medially dominating muscle traction, and external rotation of the femur.     

Functional and morphometric evaluation of end-to-side neurorrhaphy for muscle reinnervation

This study was undertaken to quantify the effect of motor collateral sprouting in an end-to-side repair model allowing end organ contact. Besides documentation of the functional outcome of muscle reinnervation by end-to-side neurorrhaphy, this experimental work was performed to determine possible downgrading effects to the donor nerve at end organ level. In 24 female New Zealand White rabbits, the motor nerve branch to the rectus femoris muscle of the right hindlimb was dissected, cut, and sutured end-to-side to the motor branch to the vastus medialis muscle after creating an epineural window. The 24 rabbits were divided into two groups of 12 each, with the second group receiving additional crush injury of the vastus branch. After a period of 8 months, maximum tetanic tension in the reinnervated rectus femoris and the vastus medialis muscles was determined. The contralateral healthy side served as control. The reinnervated rectus femoris muscle showed an average maximum tetanic force of 24.9 N (control 26.2 N, p = 0.7827), and the donor- vastus medialis muscle 11.0 N (control 7.3 N, p = 0.0223). There were no statistically significant differences between the two experimental groups (p = 0.9914). The average number of regenerated myelinated nerve fibers in the rectus femoris motor branch was 1,185 +/- 342 (control, 806 +/- 166), and the mean diameter was 4.6 +/- 0.6 microm (control, 9.4 +/- 1.0 microm). In the motor branch to the vastus medialis muscle, the mean fiber number proximal to the coaptation site was 1227 (+/-441), and decreased distal to the coaptation site to 795 (+/-270). The average difference of axon counts in the donor nerve proximal to distal regarding the repair site was 483.7 +/- 264.2. In the contralateral motor branch to the vastus medialis muscle, 540 (+/- 175) myelinated nerve fibers were counted. In nearly all cross-section specimens of the motor branch to the vastus medialis muscle, altered nerve fibers could be identified in one fascicle distal and proximal to the repair site. The results show a relevant functional reinnervation by end-to-side neurorrhaphy without functional impairment of the donor muscle. It seems to be evident that most axons in the attached segment were derived from collateral sprouts. Nonetheless, the present study confirms that end-to-side neurorrhaphy is a reliable method of reconstruction for damaged nerves, which should be applied clinically in a more extended manner.     

Length and moment arm of human leg muscles as a function of knee and hip-joint angles

Lengths of muscle tendon complexes of the quadriceps femoris muscle and some of its heads, biceps femoris and gastrocnemius muscles, were measured for six limbs of human cadavers as a function of knee and hip-joint angles. Length-angle curves were fitted using second degree polynomials. Using these polynomials the relationships between knee and hip-joint angles and moment arms were calculated. The effect of changing the hip angle on the biceps femoris muscle length is much larger than that of changing the knee angle. For the rectus femoris muscle the reverse was found. The moment arm of the biceps femoris muscle was found to remain constant throughout the whole range of knee flexion as was the case for the medial part of the vastus medialis muscle. Changes in the length of the lateral part of the vastus medialis muscle as well as the medial part of the vastus lateralis muscle are very similar to those of vastus intermedius muscle to which they are adjacent, while those changes in the length of the medial part of the vastus medialis muscle and the lateral part of the vastus lateralis muscle, which are similar to each other, differ substantially from those of the vastus intermedius muscle. Application of the results to jumping showed that bi-articular rectus femoris and biceps femoris muscles, which are antagonists, both contract eccentrically early in the push off phase and concentrically in last part of this phase.     

Knee angle-dependent oxygen consumption during isometric contractions of the knee extensors determined with near-infrared spectroscopy.

Fatigue resistance of knee extensor muscles is higher during voluntary isometric contractions at short compared with longer muscle lengths. In the present study we hypothesized that this would be due to lower energy consumption at short muscle lengths. Ten healthy male subjects performed isometric contractions with the knee extensor muscles at a 30, 60, and 90 degrees knee angle (full extension = 0 degrees ). At each angle, muscle oxygen consumption (m.VO2) of the rectus femoris, vastus lateralis, and vastus medialis muscle was obtained with near-infrared spectroscopy. m.VO2 was measured during maximal isometric contractions and during contractions at 10, 30, and 50% of maximal torque capacity. During all contractions, blood flow to the muscle was occluded with a pressure cuff (450 mmHg). m.VO2 significantly (P < 0.05) increased with torque and at all torque levels, and for each of the three muscles. m.VO2 was significantly lower at 30 degrees compared with 60 degrees and 90 degrees and m.VO2 was similar (P > 0.05) at 60 degrees and 90 degrees . Across all torque levels, average (+/- SD) m.VO2 at the 30 degrees angle for vastus medialis, rectus femoris, and vastus lateralis, respectively, was 70.0 +/- 10.4, 72.2 +/- 12.7, and 75.9 +/- 8.0% of the average m.VO2 obtained for each torque at 60 and 90 degrees . In conclusion, oxygen consumption of the knee extensors was significantly lower during isometric contractions at the 30 degrees than at the 60 degrees and 90 degrees knee angle, which probably contributes to the previously reported longer duration of sustained isometric contractions at relatively short muscle lengths.     

Patellofemoral cartilage stresses are most sensitive to variations in vastus medialis muscle forces

The purpose of this study was to evaluate the effects of variations in quadriceps muscle forces on patellofemoral stress. We created subject-specific finite element models for 21 individuals with chronic patellofemoral pain and 16 pain-free control subjects. We extracted three-dimensional geometries from high resolution magnetic resonance images and registered the geometries to magnetic resonance images from an upright weight bearing squat with the knees flexed at 60°. We estimated quadriceps muscle forces corresponding to 60° knee flexion during a stair climb task from motion analysis and electromyography-driven musculoskeletal modelling. We applied the quadriceps muscle forces to our finite element models and evaluated patellofemoral cartilage stress. We quantified cartilage stress using an energy-based effective stress, a scalar quantity representing the local stress intensity in the tissue. We used probabilistic methods to evaluate the effects of variations in quadriceps muscle forces from five trials of the stair climb task for each subject. Patellofemoral effective stress was most sensitive to variations in forces in the two branches of the vastus medialis muscle. Femur cartilage effective stress was most sensitive to variations in vastus medialis forces in 29/37 (78%) subjects, and patella cartilage effective stress was most sensitive to variations in vastus medialis forces in 21/37 (57%) subjects. Femur cartilage effective stress was more sensitive to variations in vastus medialis longus forces in subjects classified as maltrackers compared to normal tracking subjects (p?=?0.006). This study provides new evidence of the importance of the vastus medialis muscle in the treatment of patellofemoral pain.     

Neurovascular musculus obliquus internus abdominis flap free transfer for facial reanimation in a single stage

A study of the anatomy and transplantation of the musculus obliquus internus abdominis with a neurovascular pedicle transfer for facial reanimation in one stage is presented. Eleven adult cadavers (22 face sides) were dissected to observe the shape, thickness, innervation, and blood supply of the musculus obliquus internus abdominis. The blood supply of this muscle primarily comes from the musculus obliquus internus abdominis branch of the deep circumflex iliac artery (diameter, 1.3 +/- 0.2 mm), but it can also come from the eleventh intercostal artery (diameter, 1.14 +/- 0.3 mm) and the infracostal artery (diameter, 1.5 +/- 0.2 mm). The branch of the deep circumflex iliac artery and its vena comitans, or the infracostal artery and its vena comitans, could be anastomosed for muscle transplantation. The innervation of the musculus obliquus internus abdominis comes from the tenth and eleventh intercostal nerves (length, 12.7 +/- 1.5 cm) and the infracostal nerve (length, 12.9 +/- 1.3 cm). The eleventh intercostal nerve and the infracostal nerve were selected for anastomosis of muscle transplantation. From November of 1995 to November of 1999, 14 patients with long established facial paralysis were treated with transplantation of a musculus obliquus internus abdominis flap in one stage and were followed for 10 months to 6 years. In 13 patients, the dynamic functions of the transplanted muscles were restored, the obliqueness of the mouth and philtrum while static was corrected, and the facial muscle activities while smiling were harmonized. The eyelids of the paralyzed side could be closed postoperatively, indicating that the function of the orbicularis oculi of the paralyzed side was restored. The single-stage transplantation of a free musculus obliquus internus abdominis flap with one vascular, multi-nerve pedicle is a new method for facial reanimation in the treatment of long established facial paralysis. Because of the simplicity of the procedure and the completeness of the functional reanimation of the paralyzed facial muscles, compared with the results of other free muscle flap transfers, it is an ideal procedure for facial reanimation.     

In vivo patellar tracking induced by individual quadriceps components in individuals with patellofemoral pain

Patellofemoral pain is a common knee disorder with a multi-factorial etiology related to abnormal patellar tracking. Our hypothesis was that the pattern of three-dimensional rotation and translation of the patella induced by selective activation of individual quadriceps components would differ between subjects with patellofemoral pain and healthy subjects. Nine female subjects with patellofemoral pain and seven healthy female subjects underwent electrical stimulation to selectively activate individual quadriceps components (vastus medialis obliquus, VMO; vastus medialis lateralis, VML; vastus lateralis, VL) with the knee at 0° and 20° flexion, while three-dimensional patellar tracking was recorded. Normalized direction of rotation and direction of translation characterized the relative amplitudes of each component of patellar movement. VMO activation in patellofemoral pain caused greater medial patellar rotation (distal patellar pole rotates medially in frontal plane) at both knee positions (p<0.01), and both VMO and VML activation caused increased anterior patellar translation (p<0.001) in patellofemoral pain compared to healthy subjects at 20° knee flexion. VL activation caused more lateral patellar translation (p<0.001) in patellofemoral pain compared to healthy subjects. In healthy subjects the 3-D mechanical action of the VMO is actively modulated with knee flexion angle while such modulation was not observed in PFP subjects. This could be due to anatomical differences in the VMO insertion on the patella and medial quadriceps weakness. Quantitative evaluation of the influence of individual quadriceps components on patellar tracking will aid understanding of the knee extensor mechanism and provide insight into the etiology of patellofemoral pain.     

Comparing two estimations of the quadriceps force distribution for use during patellofemoral simulation

EMG analysis has indicated that the vastus lateralis and vastus medialis contribute less to the quadriceps moment during knee extension than the physiological cross-sectional areas (PCSA's) of the muscles indicate. Both PCSA- and EMG-based quadriceps force distributions were utilized while computationally simulating knee extension. For both distributions, a 10 degrees increase in the Q-angle and a 50% decrease in the force applied by the vastus medialis were simulated, and the influence of these changes on the resultant force and moment applied by the quadriceps muscles and the patella tendon was quantified. For both quadriceps force distributions, increasing the Q-angle increased the lateral force and the moment acting to rotate the distal patella laterally. Due to the relatively large forces initially attributed to the vastus medialis and vastus lateralis for the PCSA-based quadriceps force distribution, decreasing the vastus medialis force created a large force imbalance between these two muscles. For the PCSA-based quadriceps force distribution, decreasing the vastus medialis force increased the lateral rotation moment and the moment acting to tilt the patella laterally. For the EMG-based quadriceps force distribution, decreasing the vastus medialis force produced relatively little change in the tilt and rotation moments. For both quadriceps force distributions, increasing the Q-angle increased the maximum and mean cartilage pressure during flexion, but decreasing the vastus medialis force only increased the cartilage pressures for the PCSA-based quadriceps distribution. The choice of the initial quadriceps distribution can influence the outcome of patellofemoral simulation when manipulating quadriceps muscle forces.     

Ceramic cups for hip endoprostheses. 6: Cup design, inclination and antetorsion angle modify range of motion and impingement]

The present investigation focuses on total hip replacement using ceramic acetabular components. The relationship between the position of the cup and the range of motion (ROM) was investigated. A limited range of motion may cause impingement, which is defined as contact between the femoral neck and the rim of the acetabular cup. Impingement may result in wear, chipping, fracture or dislocation of the femoral head. Joint movements were simulated in a three-dimensional CAD program. The results obtained underscore the importance of correct positioning and design of the cup for achieving a ROM as close to the physiological situation as possible. With ceramic cups, the inclination angle should not be more than 45 degrees, and the antetorsion angle between 10 and 15 degrees. If the cup is too vertical, the risk of dislocation and fracture of the ceramic increases. If, on the other hand, the angle of inclination is too small, flexion and abduction will be greatly limited. The study shows that acetabular components with non-recessed ceramic inserts should not be used. Slight recession of the insert helps to avoid impingement. The ROM is reduced and the risk of impingement appreciably increased when mushroom-shaped femoral heads (XL heads) or ceramic inserts protected by a polyethylene ring are used.     

The effects of an isometric knee extension with hip adduction (KEWHA) exercise on selective VMO muscle strengthening

We investigated the effects of four weeks of training using a knee extension with hip adduction (KEWHA) exercise in asymptomatic participants. In addition, we compared different methods of electromyographic (EMG) onset-time detection. Eighteen participants who achieved earlier activation of the vastus lateralis (VL) muscle compared to that of the vastus medialis obliquus (VMO) muscle performed the isometric KEWHA exercise in the sitting position for four weeks. A 15° hip adduction was added to the existing knee extension in the KEWHA exercise. EMG onset times were detected using a computer-analyzed system and evaluated using two methods in which the thresholds for activity onset were set at two and three standard deviations (SDs) of the mean baseline activity. No significant difference in the EMG onset-time for the VMO muscle was observed compared to that of the VL muscle between the pre- and post-tests (p > 0.05) when data at 2 SDs of the mean baseline activity were analyzed. However, a significant difference in the onset times for the VMO muscle and VL muscle was found between the pre- and post-tests (p < 0.05) when data at 3 SDs of the mean baseline activity were analyzed. In addition, less variation was observed in data analyzed at 3 SDs compared to that of the data at 2 SDs. The normalized VMO:VL muscle ratio was not significantly different between the pre- and post-tests. These findings show that the KEWHA exercise may decrease the difference between the onset times of VMO and VL muscles. In addition, we suggest that task-specific EMG onset-time detection methods are required to minimize variations in the data obtained during the recording of muscle activation.     

Creatine kinase and hexose phosphate isomerase activity in skeletal muscles of healthy male adults

Creatine kinase (CPK) and hexose phosphate isomerase (PHI) activities were measured in surgically obtained skeletal muscle samples of healthy adult men (n = 45). Median values of 4,200 for CPK and 275 for PHI (U/g wet weight, 37 degrees C) were found. Duplicate determinations on 7 samples divided and treated separately gave a very good reproducibility. There is a significant relationship between the activity of the two enzymes (r = +0.798, p less than 0.001). The mean activity levels were for both enzymes higher in m. vastus medialis quadricipitis and m. triceps brachii, c. long., than in vastus lateralis quadric. and in deltoideus. PHI frequency distribution was not of the normal type but probably bimodal, suggesting muscle types with lower and higher glycolytic rate in man.     

Biomechanics of overground vs. treadmill walking in healthy individuals.

The goal of this study was to compare treadmill walking with overground walking in healthy subjects with no known gait disorders. Nineteen subjects were tested, where each subject walked on a split-belt instrumented treadmill as well as over a smooth, flat surface. Comparisons between walking conditions were made for temporal gait parameters such as step length and cadence, leg kinematics, joint moments and powers, and muscle activity. Overall, very few differences were found in temporal gait parameters or leg kinematics between treadmill and overground walking. Conversely, sagittal plane joint moments were found to be quite different, where during treadmill walking trials, subjects demonstrated less dorsiflexor moments, less knee extensor moments, and greater hip extensor moments. Joint powers in the sagittal plane were found to be similar at the ankle but quite different at the knee and hip joints. Differences in muscle activity were observed between the two walking modalities, particularly in the tibialis anterior throughout stance, and in the hamstrings, vastus medialis and adductor longus during swing. While differences were observed in muscle activation patterns, joint moments and joint powers between the two walking modalities, the overall patterns in these behaviors were quite similar. From a therapeutic perspective, this suggests that training individuals with neurological injuries on a treadmill appears to be justified.     

A femoral neck fracture model in rabbits

A technique was developed to create a reproducible femoral neck fracture in vitro using 5-month-old JW/CSK series male rabbits. Force attenuation of a newly developed damping material was also evaluated using this model. Ten pairs of the femora with smaller deviations in length and weight were harvested and cleaned of soft tissue. Either a right or left of each pair of the specimens was randomly selected and put into either the control or the experimental group, both of which contained equal numbers of the right and left femora. The specimens were attached to an L-shaped plate and embedded in a resin from the proximal diaphysis to the distal end so as to maintain a consistent position of the femora. They were mounted and fixed on a pedestal slanted in the coronal plane at 20 degrees. The impact load testing was conducted using an impact mallet dropped from a height of 3 cm. The impact load was applied onto the femoral head. To the specimens in the experimental group, attenuated impact forces were loaded through the damping material, but those in the control group were subjected to forces directly transmitted without the material. All the impact testing was performed in a temperature and humidity controlled chamber. All of the femoral specimens exposed to the direct impact forces (controlled group) sustained fracture at the neck. The fracture line passed from the base of the femoral head laterally and to the calcar area just proximal to the minor trochanter medially. The location of each fracture line was almost identical among the specimens. None of the specimens that were exposed to the impact force through the damping material (experimental group) sustained fracture macroscopically and roentgenographically.     

Biofeedback as a means to alter electromyographic activity in a total knee replacement patient

This paper presents a single case controlled study of a 75-year-old male having bilateral total knee replacement. Baseline EMG recordings demonstrated differential levels of vastus medialis and vastus lateralis muscle activity in both knees during exercise, with increased vastus lateralis activity compared to vastus medialis activity. The purpose of the study was to use electromyographic (EMG) biofeedback training to train the patient to equalize vastus medialis and vastus lateralis EMG activity during exercise. After 11 and 13 training sessions for the left and right knees, respectively, differences between vastus medialis and vastus lateralis activity had markedly decreased. Following the termination of biofeedback training, EMG activity during exercise showed a return toward baseline levels. Several concomitant changes in psychological and physical function were noted. These results suggested that EMG biofeedback can be used to train vastus medialis and vastus lateralis activity in total knee replacement patients, and that biofeedback training may produce positive benefits in other functional areas.     

Experimental study of seita-fitting

The purpose of this study was to verify the difference between carrying a load on the sacrum (LOS) and on the lumbar vertebrae (LOL) in oxygen uptake, muscle activities, heart rate, cadence, and subjective response. Nine males (26.7 +/- 3.1 years old), each carrying a 7.5 kg carrier frame and a 40 kg load, walked on a treadmill at a speed of 50 m/min. EMGs were recorded from the trapezius, rectus abdominis, erector spinae, vastus lateralis, rectus femoris, vastus medialis, biceps femoris long head, tibial anterior, soleus, medial head of gastrocnemius, and the lateral head of gastrocnemius. For each subject the integrated EMG (IEMG) was normalized by dividing the IEMG in the LOL and LOS by the IEMG in a no-load condition (NL) for each investigated muscle. The following was significantly higher in LOL than in LOS: oxygen uptake; IEMG of the tibial anterior, soleus, and medial head of gastrocnemius; cadence; and rated perceived exertion. However, IEMG of the erector spinae was significantly lower in LOL than in LOS. These results suggest that seita-fitting in LOS causes a decrease of leg muscle activities, which causes oxygen uptake to decrease beyond the increase of the erector spinae activity.     

Myoelectric manifestations of fatigue in vastus lateralis,medialis obliquus and medialis longus muscles

The purpose of this study was to determine whether surface electromyography (EMG) assessment of myoelectric manifestations of muscle fatigue is capable of detecting differences between the vastus lateralis and medialis muscles which are consistent with the results of previous biopsy studies. Surface EMG signals were recorded from the vastus medialis longus (VML), vastus medialis obliquus (VMO) and vastus lateralis (VL) muscles during isometric knee extension contractions at 60% and 80% of the maximum voluntary contraction (MVC) for 10 s and 60 s, respectively. Initial values and rate of change of mean frequency (MNF), average rectified value (ARV) and conduction velocity (CV) of the EMG signal were calculated. Comparisons between the two force levels revealed that the initial values of MNF for the VL muscle were greater at 80% MVC compared to 60% MVC (P < 0.01). Comparisons between the vasti muscles demonstrated lower initial values of CV for VMO compared to VL at 60% MVC (P < 0.01) and lower than VML and VL at 80% MVC (P < 0.01). In addition, initial values of MNF were higher for VL with respect to both VML and VMO at 80% MVC (P < 0.01) and initial estimates of ARV were higher for VMO compared to VML at both force levels (P < 0.01 at 60% MVC and P < 0.05 at 80% MVC). For the sustained contraction at 80% MVC, VL demonstrated a greater decrease in CV over time compared to VMO (P < 0.05).These findings suggest that surface EMG signals and their time course during sustained isometric contractions may be useful to non-invasively describe functional differences between the vasti muscles.     

Knee and Hip Joint Kinematics Predict Quadriceps and Hamstrings Neuromuscular Activation Patterns in Drop Jump Landings

PurposeThe purpose was to assess if variation in sagittal plane landing kinematics is associated with variation in neuromuscular activation patterns of the quadriceps-hamstrings muscle groups during drop vertical jumps (DVJ).MethodsFifty female athletes performed three DVJ. The relationship between peak knee and hip flexion angles and the amplitude of four EMG vectors was investigated with trajectory-level canonical correlation analyses over the entire time period of the landing phase. EMG vectors consisted of the {vastus medialis(VM),vastus lateralis(VL)}, {vastus medialis(VM),hamstring medialis(HM)}, {hamstring medialis(HM),hamstring lateralis(HL)} and the {vastus lateralis(VL),hamstring lateralis(HL)}. To estimate the contribution of each individual muscle, linear regressions were also conducted using one-dimensional statistical parametric mapping.ResultsThe peak knee flexion angle was significantly positively associated with the amplitudes of the {VM,HM} and {HM,HL} during the preparatory and initial contact phase and with the {VL,HL} vector during the peak loading phase (p<0.05). Small peak knee flexion angles were significantly associated with higher HM amplitudes during the preparatory and initial contact phase (p<0.001). The amplitudes of the {VM,VL} and {VL,HL} were significantly positively associated with the peak hip flexion angle during the peak loading phase (p<0.05). Small peak hip flexion angles were significantly associated with higher VL amplitudes during the peak loading phase (p = 0.001). Higher external knee abduction and flexion moments were found in participants landing with less flexed knee and hip joints (p<0.001).ConclusionThis study demonstrated clear associations between neuromuscular activation patterns and landing kinematics in the sagittal plane during specific parts of the landing. These findings have indicated that an erect landing pattern, characterized by less hip and knee flexion, was significantly associated with an increased medial and posterior neuromuscular activation (dominant hamstrings medialis activity) during the preparatory and initial contact phase and an increased lateral neuromuscular activation (dominant vastus lateralis activity) during the peak loading phase.     

Biofeedback as a means to alter electromyographic activity in a total knee replacement patient

This paper presents a single case controlled study of a 75-year-old male having bilateral total knee replacement. Baseline EMG recordings demonstrated differential levels of vastus medialis and vastus lateralis muscle activity in both knees during exercise, with increased vastus lateralis activity compared to vastus medialis activity. The purpose of the study was to use electromyographic (EMG) biofeedback training to train the patient to equalize vastus medialis and vastus lateralis EMG activity during exercise. After 11 and 13 training sessions for the left and right knees, respectively, differences between vastus medialis and vastus lateralis activity had markedly decreased. Following the termination of biofeedback training, EMG activity during exercise showed a return toward baseline levels. Several concomitant changes in psychological and physical function were noted. These results suggested that EMG biofeedback can be used to train vastus medialis and vastus lateralis activity in total knee replacement patients, and that biofeedback training may produce positive benefits in other functional areas.The authors wish to express thanks to Dr. Karen Gil for her helpful comments on a draft of this article, and Christianne Herman and Allison Roodman for their help in data collection and entry.