Optimization of cardiac cell seeding and distribution in 3D porous alginate scaffolds

Cardiac tissue engineering has evolved as a potential therapeutic approach to assist in cardiac regeneration. We have recently shown that tissue-engineered cardiac graft, constructed from cardiomyocytes seeded within an alginate scaffold, is capable of preventing the deterioration in cardiac function after myocardial infarction in rats. The present article addresses cell seeding within porous alginate scaffolds in an attempt to achieve 3D high-density cardiac constructs with a uniform cell distribution. Due to the hydrophilic nature of the alginate scaffold, its >90% porosity and interconnected pore structure, cell seeding onto the scaffold was efficient and short, up to 30 min. Application of a moderate centrifugal force during cell seeding resulted in a uniform cell distribution throughout the alginate scaffolds, consequently enabling the loading of a large number of cells onto the 3D scaffolds. The percent cell yield in the alginate scaffolds ranged between 60-90%, depending on cell density at seeding; it was 90% at seeding densities of up to 1 x 10(8) cells/cm(3) scaffold and decreased to 60% at higher densities. The highly dense cardiac constructs maintained high metabolic activity in culture. Scanning electron microscopy revealed that the cells aggregated within the scaffold pores. Some of the aggregates were contracting spontaneously within the matrix pores. Throughout the culture there was no indication of cardiomyocyte proliferation within the scaffolds, nor was it found in 3D cultures of cardiofibroblasts. This may enable the development of cardiac cocultures, without domination of cardiofibroblasts with time.     

Modeling mass transfer in hepatocyte spheroids via cell viability, spheroid size, and hepatocellular functions

Hepatocyte aggregation into spheroids attributes to their increased activity, but in the absence of a vascular network the cells in large spheroids experience mass transfer limitations. Thus, there is a need to define the spheroid size which enables maximal cell viability and productivity. We developed a combined theoretical and experimental approach to define this optimal spheroid size. Hepatocyte spheroids were formed in alginate scaffolds having a pore diameter of 100 microm, in rotating T-flasks or spinners, to yield a maximal size of 100, 200, and 600 microm, respectively. Cell viability was found to decrease with increasing spheroid size. A mathematical model was constructed to describe the relationship between spheroid size and cell viability via the oxygen mass balance equation. This enabled the prediction of oxygen distribution profiles and distribution of viable cells in spheroids with varying size. The model describes that no oxygen limitation will take place in spheroids up to 100 microm in diameter. Spheroid size affected the specific rate of albumin secretion as well; it reached a maximal level, i.e., 60 microg/million cells/day in 100-microm diameter spheroids. This behavior was depicted in an equation relating the specific albumin secretion rate to spheroid size. The calculated results fitted with the experimental data, predicting the need for a critical number of viable hepatocytes to gain a maximal albumin secretion. Taken together, the results on mass transport in spheroids and its effects on cell viability and productivity provide a useful tool for the design of 3D scaffolds with pore diameters of 100 microm.     

Micro-computed tomography image-based evaluation of 3D anisotropy degree of polymer scaffolds

Anisotropy is one of the most meaningful determinants of biomechanical behaviour. This study employs micro-computed tomography (μCT) and image techniques for analysing the anisotropy of regenerative medicine polymer scaffolds. For this purpose, three three-dimensional anisotropy evaluation image methods were used: ellipsoid of inertia (EI), mean intercept length (MIL) and tensor scale (t-scale). These were applied to three patterns (a sphere, a cube and a right prism) and to two polymer scaffold topologies (cylindrical orthogonal pore mesh and spherical pores). For the patterns, the three methods provided good results. Regarding the scaffolds, EI mistook both topologies (0.0158, [ ? 0.5683; 0.6001]; mean difference and 95% confidence interval), and MIL showed no significant differences (0.3509, [0.0656; 0.6362]). T-scale is the preferable method because it gave the best capability (0.3441, [0.1779; 0.5102]) to differentiate both topologies. This methodology results in the development of non-destructive tools to engineer biomimetic scaffolds, incorporating anisotropy as a fundamental property to be mimicked from the original tissue and permitting its assessment by means of μCT image analysis.     

Advances in 3D printing of composite scaffolds for the repairment of bone tissue associated defects

The conventional methods of using autografts and allografts for repairing defects in bone, the osteochondral bone, and the cartilage tissue have many disadvantages, like donor site morbidity and shortage of donors. Moreover, only 30% of the implanted grafts are shown to be successful in treating the defects. Hence, exploring alternative techniques such as tissue engineering to treat bone tissue associated defects is promising as it eliminates the above-mentioned limitations. To enhance the mechanical and biological properties of the tissue engineered product, it is essential to fabricate the scaffold used in tissue engineering by the combination of various biomaterials. Three-dimensional (3D) printing, with its ability to print composite materials and with complex geometry seems to have a huge potential in scaffold fabrication technique for engineering bone associated tissues. This review summarizes the recent applications and future perspectives of 3D printing technologies in the fabrication of composite scaffolds used in bone, osteochondral, and cartilage tissue engineering. Key developments in the field of 3D printing technologies involves the incorporation of various biomaterials and cells in printing composite scaffolds mimicking physiologically relevant complex geometry and gradient porosity. Much recently, the emerging trend of printing smart scaffolds which can respond to external stimulus such as temperature, pH and magnetic field, known as 4D printing is gaining immense popularity and can be considered as the future of 3D printing applications in the field of tissue engineering.     

Renal tissue reconstitution by the implantation of renal segments on biodegradable polymer scaffolds

Renal units were created in vivo by transplanting isolated renal segments on three-dimensional, biodegradable polymer scaffolds. Renal segments, freshly isolated from rat kidneys, were seeded on polymer scaffolds and subcutaneously implanted in athymic mice for two and four weeks. Three-dimensional renal reconstructs were formed with glomeruli and tubules, showing a possibility of reconstituting renal structures by transplanting renal segments.     

3D printed PLA-based scaffolds

Rapid prototyping (RP), also known as additive manufacturing (AM), has been well received and adopted in the biomedical field. The capacity of this family of techniques to fabricate customized 3D structures with complex geometries and excellent reproducibility has revolutionized implantology and regenerative medicine. In particular, nozzle-based systems allow the fabrication of high-resolution polylactic acid (PLA) structures that are of interest in regenerative medicine. These 3D structures find interesting applications in the regenerative medicine field where promising applications including biodegradable templates for tissue regeneration purposes, 3D in vitro platforms for studying cell response to different scaffolds conditions and for drug screening are considered among others. Scaffolds functionality depends not only on the fabrication technique, but also on the material used to build the 3D structure, the geometry and inner architecture of the structure, and the final surface properties. All being crucial parameters affecting scaffolds success. This Commentary emphasizes the importance of these parameters in scaffolds’ fabrication and also draws the attention toward the versatility of these PLA scaffolds as a potential tool in regenerative medicine and other medical fields.     

Modeling of flow‐induced shear stress applied on 3D cellular scaffolds: Implications for vascular tissue engineering

Novel tissue‐culture bioreactors employ flow‐induced shear stress as a means of mechanical stimulation of cells. We developed a computational fluid dynamics model of the complex three‐dimensional (3D) microstructure of a porous scaffold incubated in a direct perfusion bioreactor. Our model was designed to predict high shear‐stress values within the physiological range of those naturally sensed by vascular cells (1–10 dyne/cm²), and will thereby provide suitable conditions for vascular tissue‐engineering experiments. The model also accounts for cellular growth, which was designed as an added cell layer grown on all scaffold walls. Five model variants were designed, with geometric differences corresponding to cell‐layer thicknesses of 0, 50, 75, 100, and 125 µm. Four inlet velocities (0.5, 1, 1.5, and 2 cm/s) were applied to each model. Wall shear‐stress distribution and overall pressure drop calculations were then used to characterize the relation between flow rate, shear stress, cell‐layer thickness, and pressure drop. The simulations showed that cellular growth within 3D scaffolds exposes cells to elevated shear stress, with considerably increasing average values in correlation to cell growth and inflow velocity. Our results provide in‐depth analysis of the microdynamic environment of cells cultured within 3D environments, and thus provide advanced control over tissue development in vitro. Biotechnol. Bioeng. 2010; 105: 645–654. © 2009 Wiley Periodicals, Inc.     

A new method of fabricating robust freeform 3D ceramic scaffolds for bone tissue regeneration

Fabrication of three‐dimensional (3D) scaffolds with appropriate mechanical properties and desired architecture for promoting cell growth and new tissue formation is one of the most important efforts in tissue engineering field. Scaffolds fabricated from bioactive ceramic materials such as hydroxyapatite and tricalcium phosphate show promise because of their biological ability to support bone tissue regeneration. However, the use of ceramics as scaffold materials is limited because of their inherent brittleness and difficult processability. The aim of this study was to create robust ceramic scaffolds, which have a desired architecture. Such scaffolds were successfully fabricated by projection‐based microstereolithography, and dilatometric analysis was conducted to study the sintering behavior of the ceramic materials. The mechanical properties of the scaffolds were improved by infiltrating them with a polycaprolactone solution. The toughness and compressive strength of these ceramic/polymer scaffolds were about twice those of ceramic scaffolds. Furthermore, the osteogenic gene expression on ceramic/polymer scaffolds was better than that on ceramic scaffolds. Through this study, we overcame the limitations of previous research on fabricating ceramic scaffolds and these new robust ceramic scaffolds may provide a much improved 3D substrate for bone tissue regeneration. Biotechnol. Bioeng. 2013; 110: 1444–1455. © 2012 Wiley Periodicals, Inc.     

Numerical and experimental evaluation of TPMS Gyroid scaffolds for bone tissue engineering

The combination of computational methods with 3D printing allows for the control of scaffolds microstructure. Lately, triply periodic minimal surfaces (TPMS) have been used to design porosity-controlled scaffolds for bone tissue engineering (TE). The goal of this work was to assess the mechanical properties of TPMS Gyroid structures with two porosity levels (50 and 70%). The scaffold stiffness function of porosity was determined by the asymptotic homogenisation method and confirmed by mechanical testing. Additionally, microCT analysis confirmed the quality of the printed parts. Thus, the potential of both design and manufacturing processes for bone TE applications is here demonstrated.     

N-acetylglucosamine and adenosine derivatized surfaces for cell culture: 3T3 fibroblast and chicken hepatocyte response

3T3 fibroblasts and primary chicken hepatocytes were cultured on derivatized polystyrene surfaces to examine the effect of cell-specific ligands on cellular morphology and growth. Surfaces were prepared by derivatizing chloromethylated polystyrene with N-acetylglucosamine (GlcNAc; recognized by the chicken asialoglycoprotein receptor) and adenosine (not recognized by adult hepatocytes). These surfaces were compared with tissue culture polystyrene (TCPS), acid-cleaned glass, and the unmodified chloromethylated polystyrene. The spreading, cytoskeletal structure and growth of the fibroblasts following attachment to these surfaces were examined. The extent of attachment, total protein levels, and DNA contents for surfaces-attached chicken hepatocytes were also measured. Fibroblast spreading was greatest on polymer surfaces derivatized with GlcNAc, whereas cytoskeletal structure and growth rate were independent of surface chemistry. Although chicken hepatocytes attached most efficiently to the GlcNAc derivatized polymer, the total protein and DNA levels of the surface-attached cells were not affected. In anticipation of the application of these polymers for cell culture and hybrid artificial organ design, the GlcNAc-derivatized polystryrene was fabricated into porous microcarriers. Fibroblasts grew avidly on the microcarriers, whereas chicken hepactocytes adhered well to the formed large aggregates arounds the microcarriers.     

A microfabricated array bioreactor for perfused 3D liver culture

We describe the design, fabrication, and performance of a bioreactor that enables both morphogenesis of 3D tissue structures under continuous perfusion and repeated in situ observation by light microscopy. Three-dimensional scaffolds were created by deep reactive ion etching of silicon wafers to create an array of channels (through-holes) with cell-adhesive walls. Scaffolds were combined with a cell-retaining filter and support in a reactor housing designed to deliver a continuous perfusate across the top of the array and through the 3D tissue mass in each channel. Reactor dimensions were constructed so that perfusate flow rates meet estimated values of cellular oxygen demands while providing fluid shear stress at or below a physiological range (<2 dyne cm(2)), as determined by comparison of numerical models of reactor fluid flow patterns to literature values of physiological shear stresses. We studied the behavior of primary rat hepatocytes seeded into the reactors and cultured for up to 2 weeks, and found that cells seeded into the channels rearranged extensively to form tissue like structures and remained viable throughout the culture period. We further observed that preaggregation of the cells into spheroidal structures prior to seeding improved the morphogenesis of tissue structure and maintenance of viability. We also demonstrate repeated in situ imaging of tissue structure and function using two-photon microscopy.     

Hydrogels as extracellular matrix mimics for 3D cell culture

Methods for culturing mammalian cells ex vivo are increasingly needed to study cell and tissue physiology and to grow replacement tissue for regenerative medicine. Two‐dimensional culture has been the paradigm for typical in vitro cell culture; however, it has been demonstrated that cells behave more natively when cultured in three‐dimensional environments. Permissive, synthetic hydrogels and promoting, natural hydrogels have become popular as three‐dimensional cell culture platforms; yet, both of these systems possess limitations. In this perspective, we discuss the use of both synthetic and natural hydrogels as scaffolds for three‐dimensional cell culture as well as synthetic hydrogels that incorporate sophisticated biochemical and mechanical cues as mimics of the native extracellular matrix. Ultimately, advances in synthetic–biologic hydrogel hybrids are needed to provide robust platforms for investigating cell physiology and fabricating tissue outside of the organism. Biotechnol. Bioeng. 2009;103: 655–663. © 2009 Wiley Periodicals, Inc.     

Monolayer culture of parenchymal rat hepatocytes on collagen-coated microcarriers. A hepatocyte system for short- and long-term metabolic studies

Summary A method is described for the attachment to and monolayer culture of adult rat hepatocytes on collagen-coated or fibronectin-coated microbeads or both in a chemically defined serum-free medium. Protein synthesis measured by the incorporation of [³H]leucine into protein was four-fold higher in the hepatocyte microcarrier cultures than in isolated hepatocyte suspensions. The hepatocyte microcarrier cultures showed acute responsiveness to insulin of fatty acid synthesis, glucose incorporation into glycogen, and decarboxylation of [1-¹⁴C]pyruvate. Microcarrier-cultured hepatocytes have the combined advantages of monolayer culture and suspension systems. They are a potential tool for the study of long-term as well as acute effects of hormones. This work was supported by the British Diabetic Association.     

SEM and 3D synchrotron radiation micro-tomography in the study of bioceramic scaffolds for tissue-engineering applications

Different biomaterials have been proposed as scaffolds for the delivery of cells and/or biological molecules to repair or regenerate damaged or diseased bone tissues. Particular attention is being given to porous bioceramics that mimic trabecular bone chemistry and structure. Chemical composition, density, pore shape, pore size, and pore interconnection are elements that have to be considered to improve the efficiency of these biomaterials. Commonly, two-dimensional (2D) systems of analysis such as scanning electron microscope (SEM) are used for the characterization and comparison of the scaffolds. Unfortunately, these systems do not allow a complete investigation of the three-dimensional (3D) spatial structure of the scaffold. In this study, we have considered two different techniques, that is, SEM and 3D synchrotron radiation (SR) micro-CT to extract information on the geometry of two hydroxyapatite (HA) bioceramics with identical chemical composition but different micro-porosity, pore size distribution, and pore interconnection pathway. The two scaffolds were obtained with two different procedures: (a) sponge matrix embedding (scaffold FB), and (b) foaming (scaffold EP). Both scaffolds showed structures suitable for tissue-engineering applications, but scaffold EP appeared superior with regard to interconnection of pores, surface on which the new bone could be deposited, and percentage of volume available to bone deposition.     

Collagen type I and hyaluronic acid based hybrid scaffolds for heart valve tissue engineering

Tissue engineers have achieved limited success so far in designing an ideal scaffold for aortic valve; scaffolds lack in mechanical compatibility, appropriate degradation rate, and microstructural similarity. This paper, therefore, has demonstrated a carbodiimide-based sequential crosslinking technique to prepare aortic valve extracellular matrix mimicking (ECM) hybrid scaffolds from collagen type I and hyaluronic acid (HA), the building blocks of heart valve ECM, with tailorable crosslinking densities. Swelling studies revealed that crosslinking densities of parent networks increased with increasing the concentration of the crosslinking agents whereas crosslinking densities of hybrid scaffolds averaged from those of parent collagen and HA networks. Hybrid scaffolds also offered a wide range of pore size (66-126 μm) which fulfilled the criteria for valvular tissue regeneration. Scanning electron microscopy and images of Alcian blue-Periodic acid Schiff stained samples suggested that our crosslinking technique yielded an ECM mimicking microstructure with interlaced bands of collagen and HA in the hybrid scaffolds. The mutually reinforcing networks of collagen and HA also resulted in increased bending moduli up to 1660 kPa which spanned the range of natural aortic valves. Cardio sphere-derived cells (CDCs) from rat hearts showed that crosslinking density affected the available cell attachment sites on the surface of the scaffold. Increased bending moduli of CDCs seeded scaffolds up to two folds (2-6 kPa) as compared to the non-seeded scaffolds (1 kPa) suggested that an increase in crosslinking density of the scaffolds could not only increase the in vitro bending modulus but also prevented its disintegration in the cell culture medium.     

Fabrication of 3D calcium-alginate scaffolds for human glioblastoma modeling and anticancer drug response evaluation

The three-dimensional (3D) cell culture model has been increasingly used to study cancer biology and screen for anticancer agents due to its close mimicry to in vivo tumor biopsies. In this study, 3D calcium(Ca)-alginate scaffolds were developed for human glioblastoma cell culture and an investigation of the responses to two anticancer agents, doxorubicin and cordycepin. Compared to the 2D monolayer culture, glioblastoma cells cultured on these 3D Ca-alginate scaffolds showed reduced cell proliferation, increased tumor spheroid formation, enhanced expression of cancer stem cell genes (CD133, SOX2, Nestin, and Musashi-1), and improved expression of differentiation potential-associated genes (GFAP and β-tubulin III). Additionally, the vascularization potential of the 3D glioblastoma cells was increased, as indicated by a higher expression of tumor angiogenesis biomarker (VEGF) than in the cells in 2D culture. To highlight the application of Ca-alginate scaffolds, the 3D glioblastomas were treated with anticancer agents, including doxorubicin and cordycepin. The results demonstrated that the 3D glioblastomas presented a greater resistance to the tested anticancer agents than that of the cells in 2D culture. In summary, the 3D Ca-alginate scaffolds for glioblastoma cells that were developed in this study offer a promising platform for anticancer agent screening and the discovery of drug-resistant mechanisms of cancer.     

3D culture of osteoblast‐like cells by unidirectional or oscillatory flow for bone tissue engineering

A medium perfusion system is expected to be beneficial for three‐dimensional (3D) culture of engineered bone, not only by chemotransport enhancement but also by mechanical stimulation. In this study, perfusion systems with either unidirectional or oscillatory medium flow were developed, and the effects of the different flow profiles on 3D culturing of engineered bone were studied. Mouse osteoblast‐like MC 3T3‐E1 cells were 3D‐cultured with porous ceramic scaffolds in vitro for 6 days under static and hydrodynamic conditions with either a unidirectional or oscillatory flow. We found that, in the static culture, the cells proliferated only on the scaffold surfaces. In perfusion culture with the unidirectional flow, the proliferation was significantly higher than in the other groups but was very inhomogeneous, which made the construct unsuitable for transplantation. Only the oscillatory flow allowed osteogenic cells to proliferate uniformly throughout the scaffolds, and also increased the activity of alkaline phosphatase (ALP). These results suggested that oscillatory flow might be better than unidirectional flow for 3D construction of cell‐seeded artificial bone. The oscillatory perfusion system could be a compact, safe, and efficient bioreactor for bone tissue engineering. Biotechnol. Bioeng. 2009;102: 1670–1678. © 2008 Wiley Periodicals, Inc.