Three-dimensional dynamic hip contact area and pressure distribution during activities of daily living

Estimation of the hip joint contact area and pressure distribution during activities of daily living is important in predicting joint degeneration mechanism, prosthetic implant wear, providing biomechanical rationales for preoperative planning and postoperative rehabilitation. These biomechanical data were estimated utilizing a generic hip model, the Discrete Element Analysis technique, and the in vivo hip joint contact force data. The three-dimensional joint potential contact area was obtained from the anteroposterior radiograph of a subject and the actual joint contact area and pressure distribution in eight activities of daily living were calculated. During fast, normal, and slow walking, the peak pressure of moderate magnitude was located at the lateral roof of the acetabulum during mid-stance. In standing up and sitting down, and during knee bending, the peak pressures were located at the edge of the posterior horn and the magnitude of the peak pressure during sitting down was 2.8 times that of normal walking. The peak pressure was found at the lateral roof in climbing up stairs which was higher than that in going down stairs. These results can be used to rationalize rehabilitation protocols, functional restrictions after complex acetabular reconstructions, and prosthetic component wear and fatigue test set up. The same model and analysis can provide further insight to soft tissue loading and pathology such as labral injury. When the pressure distribution on the acetabulum is inverted onto the femoral head, prediction of subchondral bone collapse associated with avascular necrosis can be achieved with improved accuracy.     

Loads on an internal spinal fixation device during sitting.

Sitting is often assumed to involve high loads on the spine as well as on implants for stabilising the spine. Loads on internal spinal fixation devices were therefore measured in ten patients sitting on several types of seats, including a stool, a stool with a padded wedge, a chair, a physiotherapy ball, a knee-stool, and a bench. The patients also successively sat relaxed and erect on a stool. In addition, six of them sat on a special chair allowing different inclinations of the backrest. Implant loads were also measured for standing up and sitting down. There were only minor differences in fixator loads for sitting on the different types of seats. Sitting erect caused an average of 11% higher implant loads than sitting relaxed. Implant loads decreased with increasing inclination of the upper body while sitting on a chair with an adjustable backrest. Implant loads were about 27% higher for standing up and sitting down than for sitting.     

The transmission of translational seat vibration to the head--I. Vertical seat vibration

Vibration in the three translational (fore-and-aft, lateral and vertical) and the three rotational (roll, pitch and yaw) axes of the head has been measured during exposure to whole-body random vibration. Using an instrumented bar gripped between the teeth, the influence of variations in bite grip and bite-bar mass on movements of the head were found to be small up to a mass of 375 g. The repeatability of measures of seat-to-head transmissibility within a single subject and the variability in transmissibility across a group of twelve subjects have been determined with two seating conditions: a rigid seat with a backrest and the same seat with no backrest. Seat-to-head transmissibilities associated with vertical seat vibration are presented at frequencies up to 25 Hz for all six axes of head vibration both with and without a backrest. Head motion occurred principally in the fore-and-aft, vertical and pitch axes of the head. The backrest increased the magnitude of head vibration in most cases. Intra-subject variability was generally small compared to inter-subject variability.     

Biomechanics of vibration reception in the bullfrog,Rana catesbeiana

The opercularis system (OPS) of amphibians consists of an opercularis muscle that connects the shoulder girdle skeleton to the operculum, a movable element in the oval window of the otic capsule. The role of the OPS in reception of vibrations was examined in bullfrogs (Rana catesbeiana) tested in various postures that manipulated differential motion between the shoulder girdle (the origin of the opercularis muscle) and skull (including the inner ear). Amplitude and phase relationship of motions of the suprascapular cartilage of the shoulder girdle and the posterior skull were also measured during these tests. 1. Microphonic responses to vertical vibrations from 25-200 Hz were typically highest when frogs were in a normal, sitting posture with the head held off the vibrating platform. Responses from animals in which the head directly contacted the platform were often less (by up to 10 dB at certain frequencies). Responses from all test positions were highest at lower frequencies, especially between 50-100 Hz. 2. Suprascapular accelerations were typically highest in the normal, sitting posture, and at lower frequencies (50-75 Hz) were often greater than that of the vibrating platform by up to 8 dB. The shoulder girdle skeleton of the bullfrog is therefore readily affected by vertical substrate motion. 3. The amplitude of microphonic responses in the different test postures did not correspond well with head acceleration. Rather, response amplitude corresponded best with the absolute difference between shoulder and head motion. For example, in the normal posture, suprascapular motion was much greater than head motion, and responses were relatively high. If only the head was vibrated, head motion was high and shoulder motion low, and responses also were relatively high. If the head and body were vibrated together, their motions were similar, and responses to the same platform accelerations were often reduced. Phase differences between shoulder and head motions were small at the frequencies examined and may be of little functional significance. The importance of differences in shoulder and head motion suggests that the resulting differential motion of the operculum and inner ear fluids can produce waves that stimulate appropriate end organs (such as the saccule). 4. Removal of the opercularis muscle reduced responses up to 18 dB at certain frequencies in some of the test postures. The most significant reductions were observed in those postures with a significant difference between shoulder and head motion (such as the normal posture).(ABSTRACT TRUNCATED AT 400 WORDS)     

The mechanisms that enable arm motion to enhance vertical jump performance-a simulation study

The reasons why using the arms can increase standing vertical jump height are investigated by computer simulations. The human models consist of four/five segments connected by frictionless joints. The head-trunk-arms act as a fourth segment in the first model while the arms become a fifth segment in the second model. Planar model movement is actuated by joint torque generators. Each joint torque is the product of three variable functions of activation level, angular velocity dependence, and maximum isometric torque varying with joint angle. Simulations start from a balanced initial posture and end at jump takeoff. Jump height is maximized by finding the optimal combination of joint activation timings. Arm motion enhances jumping performance by increasing mass center height and vertical takeoff velocity. The former and latter contribute about 1/3 and 2/3 to the increased height, respectively. Durations in hip torque generation and ground contact period are lengthened by swinging the arms. Theories explaining the performance enhancement caused by arms are examined. The force transmission theory is questionable because shoulder joint force due to arm motion does not precisely reflect the change in vertical ground reaction force. The joint torque/work augmentation theory is acceptable only at the hips but not at the knees and ankles because only hip joint work is considerably increased. The pull/impart energy theory is also acceptable because shoulder joint work is responsible for about half of the additional energy created by arm swings.     

Postural-induced phase shift of respiratory sinus arrhythmia and blood pressure variations: insight from respiratory-phase domain analysis

The purpose of this study is to evaluate the multiple effects of respiration on cardiovascular variability in different postures, by analyzing respiratory sinus arrhythmia (RSA) and respiratory-related blood pressure (BP) variations for systolic BP (SBP), diastolic BP (DBP), and pulse pressure (PP) in the respiratory-phase domain. The measurements were conducted for 420 s on healthy humans in the sitting and standing positions, while the subjects were continuously monitored for heart rate and BP variability and instantaneous lung volume. The waveforms of RSA and respiratory-related BP variations were extracted as a function of the respiratory phase. In the standing position, the waveforms of the BP variations for SBP, DBP, and PP show their maxima at around the end of expiration (pi rad) and the minima at around the end of inspiration (2 pi rad), while the waveform of RSA is delayed by approximately 0.35 pi rad compared with the BP waveforms. On the other hand, in the sitting position, the phase of the DBP waveform (1.69 pi rad) greatly and significantly (P < 0.01) differs from that in the standing position (1.20 pi rad). Also, the phase of PP is delayed and that of RSA is advanced in the sitting position (P < 0.01). In particular, the phase shift of the DBP waveform is sufficiently large to alter whole hemodynamic fluctuations, affecting the amplitudes of SBP and PP variations. We conclude that the postural change associated with an altered autonomic balance affects not only the amplitude of RSA, but also the phases of RSA and BP variations in a complicated manner, and the respiratory-phase domain analysis used in this study is useful for elucidating the dynamic mechanisms of RSA.     

A Novel Approach for Dynamic Testing of Total Hip Dislocation under Physiological Conditions

Constant high rates of dislocation-related complications of total hip replacements (THRs) show that contributing factors like implant position and design, soft tissue condition and dynamics of physiological motions have not yet been fully understood. As in vivo measurements of excessive motions are not possible due to ethical objections, a comprehensive approach is proposed which is capable of testing THR stability under dynamic, reproducible and physiological conditions. The approach is based on a hardware-in-the-loop (HiL) simulation where a robotic physical setup interacts with a computational musculoskeletal model based on inverse dynamics. A major objective of this work was the validation of the HiL test system against in vivo data derived from patients with instrumented THRs. Moreover, the impact of certain test conditions, such as joint lubrication, implant position, load level in terms of body mass and removal of muscle structures, was evaluated within several HiL simulations. The outcomes for a normal sitting down and standing up maneuver revealed good agreement in trend and magnitude compared with in vivo measured hip joint forces. For a deep maneuver with femoral adduction, lubrication was shown to cause less friction torques than under dry conditions. Similarly, it could be demonstrated that less cup anteversion and inclination lead to earlier impingement in flexion motion including pelvic tilt for selected combinations of cup and stem positions. Reducing body mass did not influence impingement-free range of motion and dislocation behavior; however, higher resisting torques were observed under higher loads. Muscle removal emulating a posterior surgical approach indicated alterations in THR loading and the instability process in contrast to a reference case with intact musculature. Based on the presented data, it can be concluded that the HiL test system is able to reproduce comparable joint dynamics as present in THR patients.     

Analysis of standing up and sitting down in humans: definitions and normative data presentation

A formal definition of human standing up and sitting down movements based on sagittal plane goniometric and force plate data from 20 normal subjects is presented. This definition is comparable to the established gait cycle diagram, and consists of defined characteristic events and relative time intervals between them. The characteristic events are selected primarily on changes in ground reaction forces. The terminology proposed may be valuable for introducing more formalized and standardized reporting of both qualitative and quantitative studies in both normals and in patients. This presentation is directed toward the process of defining generally acceptable standards for human standing up and sitting down movements.     

人体坐下站起过程中平衡功能评估及训练系统软件的设计与实现

本研究针对脑卒中偏瘫患者的平衡功能定量评估的需求,设计一种针对坐下站起过程中各阶段平衡功能评估及训练的系统软件,该软件配合坐位站起平衡功能训练仪使用。软件采用面向对象编程技术,应用VS2010(Microsoft Visual Studio2010)开发平台编写,可实时获得人体在坐下站起过程中的各评估参数,包括左右臀前后最大压力、左右足底平均压力、伸展期时间、伸展前期时间、左右侧最大和平均压力及站起时的最大加速度等。结合图形和数字实时显示及虚拟现实技术,对人体坐下站起的各阶段进行平衡功能评估和训练,通过视觉、听觉反馈,使训练更具趣味性。经过测试应用,结果表明,该系统软件运行稳定可靠,具有针对性的评估并结合实时可观测的压力曲线及大量的评估参数,可使评估结果更快速更有效。     

Use of Motor Abundance in Young and Older Adults during Dual-Task Treadmill Walking

Motor abundance allows individuals to perform any task reliably while being variable in movement's particulars. The study investigated age-related differences in this feature when young adults (YA) and older adults (OA) performed challenging tasks, namely treadmill walking alone and while performing a cognitive task. A goal function for treadmill walking was first defined, i.e., maintain constant speed at each step, which led to a goal equivalent manifold (GEM) containing all combinations of step time and step length that equally satisfied the function. Given the GEM, amounts of goal-equivalent and non-goal-equivalent variability were afterwards determined and used to define an index providing information about the set of effective motor solutions relative to the GEM. The set was limited in OA compared to YA in treadmill walking alone, indicating that OA made less flexible use of motor abundance than YA. However, this differentiation between YA and OA disappeared when concurrently performing the cognitive task. It is proposed that OA might have benefited from cognitive compensation.     

Influence of high ambient temperatures on the physiological responses and body sway in healthy young adults after quickly standing

This study was aimed to compare the variations in cerebral oxygenation, blood pressure and center-of-foot pressure after standing from sitting and supine positions at normal (22 degrees C) and high (32 degrees C) room temperatures. Thirty young adults stood up from a resting posture (sitting or supine position) and kept the static standing posture for 90 sec. Meanwhile, their center-of-foot pressure (COP), blood pressure, and cerebral oxygenation kinetics were measured in continuity. The change of the frequency domain low-to-high frequency (LF/HF) ratio of the R-R interval before and after standing from a supine position was significantly higher than that from a sitting position under both temperature conditions. Blood pressure as well as total and oxygenated hemoglobin levels decreased immediately after standing up and the ratio of blood pressure change when moving from a supine position to standing at high room temperature was the largest as compared with the other conditions. Total hemoglobin (Hb) volume was found to temporarily decrease after standing and required 22-24 sec to recover when the subject started from the sitting position and 33-36 sec when the subject started from the supine position. Cerebral oxygenation kinetics tended to be larger under high, rather than normal, temperature conditions. All COP parameters after standing were significantly larger in the high temperature condition than in the normal temperature condition. Body sway after standing was larger in the high temperature condition than in the normal temperature condition and after standing from a supine position than from a sitting position. In conclusion, cerebral oxygenation kinetics and blood pressure measured after the subject moved to the standing position changed dramatically under high temperature conditions, and variations in this parameter may influence body sway.     

Ability of short-time Fourier transform method to detect transient changes in vagal effects on hearts: a pharmacological blocking study

Conventional spectral analyses of heart rate variability (HRV) have been limited to stationary signals and have not allowed the obtainment of information during transient autonomic cardiac responses. In the present study, we evaluated the ability of the short-time Fourier transform (STFT) method to detect transient changes in vagal effects on the heart. We derived high-frequency power (HFP, 0.20-0.40 Hz) as a function of time during active orthostatic task (AOT) from the sitting to standing posture before and after selective vagal (atropine sulfate 0.04 mg/kg) and sympathetic (metoprolol 0.20 mg/kg) blockades. The HFP minimum point during the first 30 s after standing up was calculated and compared with sitting and standing values. Reactivity scores describing the fast and slow HFP responses to AOT were calculated by subtracting the minimum and standing values from the sitting value, respectively. The present results, obtained without controlled respiration, showed that in the drug-free condition, HFP decreased immediately after standing up (P < 0.001) and then gradually increased toward the level characteristic for the standing posture (P < 0.001), remaining lower than in the sitting baseline posture (P < 0.001). The magnitudes of the fast and slow HFP responses to AOT were abolished by the vagal blockade (P < 0.001) and unaffected by the sympathetic blockade. These findings indicate that HFP derived by the STFT method provided a tool for monitoring the magnitude and time course of transient changes in vagal effects on the heart without the need to interfere with normal control by using blocking drugs.     

The transmission of translational seat vibration to the head--II. Horizontal seat vibration

The second part of this study of the six axes of head motion caused by translational seat vibration is concerned with the effect of fore-and-aft (x-axis) and lateral (y-axis) seat vibration. Seat-to-head transmissibilities have been determined at frequencies up to 16 Hz for each of the three translational and three rotational axes of the head during exposure to random vibration of the seat. Repeatability measures within a single subject and studies of the variability across a group of twelve subjects have been conducted with two seating conditions: a rigid seat with a backrest, and the same seat with no backrest. Fore-and-aft seat motion mainly resulted in head motion within the mid-sagittal plane (x-z plane). Without the backrest, transmissibilities for the fore-and-aft, vertical and pitch axes of the head were greatest at about 2 Hz. The backrest greatly increased head vibration at frequencies above 4 Hz and caused a second peak in the transmissibility curves at about 6 to 8 Hz. Lateral seat motion mainly caused lateral head motion with a maximum transmissibility at about 2 Hz. The backrest had little effect on the transmission of lateral vibration to the head. For both axes of excitation inter-subject variability was much greater than intra-subject variability.     

An examination of the flexion-relaxation phenomenon in the cervical spine in lumbo-pelvic sitting

The flexion-relaxation phenomenon (FRP) is well documented at end-range lumbar spine flexion in both standing and sitting however, the FRP has been insufficiently investigated in cervico-thoracic musculature. The aim of this study was to determine whether the FRP occurs during forward flexion of the neck, in lumbo-pelvic sitting, amongst a pain-free population. Surface electromyography (EMG) was used to measure muscle activation in 20 (10 men, 10 women) asymptomatic subjects in selected cervico-thoracic muscles during four, 5-s phases (upright posture, forward flexion, full flexion and return to upright) while subjects were positioned in lumbo-pelvic sitting. Spinal kinematics were simultaneously measured using an electromagnetic motion tracking device. No FRP was observed in upper trapezius or thoracic erector spinae (T4). When using visual methods to determine the presence/absence of the FRP, five subjects were believed to show evidence of the FRP in the cervical erector spinae. However, when using various non-visual criteria to determine the existence of the FRP, substantial variations (0–13 subjects) were evident. We recommend that criteria based upon relatively large differences in muscle activation should be considered when defining the FRP. These findings are of significance for future investigations examining specific cervical pain disorders.     

Dependence of joint stiffness on the conditions of visual control in upright undisturbed stance in humans

We recorded the sagittal and frontal components of the stabilogram of healthy humans in upright undisturbed stance under five conditions of visual control: (i) open eyes (OE); (ii) closed eyes (CE); (iii) visual inversion (VI); (iv) central vision (CV), and (v) diffused light (DL). Through a low-pass filter of trajectories of the center of pressure of feet (CPF), the vertical projection of the center of gravity (CG) and, consequently, the difference CPF-CG were estimated. The former represents the controlled variable, while the latter is proportional to the horizontal acceleration and assumed to express the resultant joint stiffness (mostly in the ankle joints). The stiffness was characterized through a method based on spectral analysis of the CPF-CG variable and subsequent calculations of the median frequency (MF) and the root mean square (RMS) of the spectra. The median frequencies of the spectra of the CPF-CG variable changed slightly under various visual conditions. At standing on a rigid support, they varied from 0.97 to 0.99 Hz and from 0.93 to 0.97 Hz for the CPF-CG, calculated from the sagittal and frontal components of the stabilogram, respectively. Under conditions of a pliable support, the corresponding frequencies varied within the limits of 0.79–0.83 Hz and 0.74–0.78 Hz. In contrast to the median frequencies, the RMSs demonstrated greater variability depending on different visual conditions. At standing on a rigid support, paired comparisons showed significant differences between the RMSs of the spectra of the CPF-CG variable of the sagittal direction under CE and OE conditions (0.14 ± 0.030 and 0.09 ± 0.020 mm, respectively) and under DL and OE conditions (0.130 ± ± 0.025 and 0.090 ± 0.020 mm, respectively). The RMS of the CPF-CG variable calculated for the frontal stabilogram differed significantly from each other for the VI and OE conditions (0.115 ± 0.020 and 0.075 ± ± 0.015 mm, respectively). In case of standing on a pliable support, a greater variability of visual influences on the CPF-CG variable was found. The RMS for its sagittal motion was the greatest under CE conditions (0.19 ± 0.03 mm); it was significantly greater than the respective values under OE, CV, and DL conditions (0.097 ± ± 0.020, 0.110 ± 0.020, and 0.140 ± 0.030 mm, respectively). The means of RMSs of the spectra of the frontal CPF-CG was also the greatest under CE conditions (0.20 ± 0.03 mm) and the smallest under OE conditions (0.095 ± 0.020 mm). In addition, the value of the RMS fluctuations under CE conditions (0.150 ± 0.025 mm) differed significantly from the respective values under OE conditions (0.095 ± 0.020 mm) and CV conditions (0.110 ± 0.020 mm). Thus, our findings support the statement that the influence of visual conditions on the maintenance of vertical stance is mediated (at least partially) by the mechanisms controlling the ankle joint stiffness. This regulation is mostly manifested in changes of a single parameter, the amplitude of fluctuations of the CPF-CG variable. We also found that the joint stiffness can be modulated by both nonspecific visual influences (which, in particular, reflect the perception of illumination) and specific visual influences, related to information on the position of the body and on its movements with respect to external objects. Neirofiziologiya/Neurophysiology, Vol. 38, No. 2, pp. 157–166, March–April, 2006.     

Heart rate variability during head down tilt and lower body negative pressure in the Russian Tschibis

The cardiovascular function in space seems to be normal. However, abnormalities of cardiovascular responses have been found during lower body negative pressure suction in space. The etiology of the cardiovascular deconditioning in space is still unknown. A previous study showed, that short periods of head down tilt (HDT-6 degrees) induce changes in the spectral pattern of heart rate variabilty (HRV) and an increase in the sympathethic activation caused by orthostatic stress. The aim of this study was to test following hypotheses: 1. The dynamic of heart rate variability is different in the head down tilt and supine positions. 2. The application of lower body negative pressure (LBNP) during head down tilt induces similar heart rate variability patterns like the standing position. 3. After short term head down tilt the cardiovascular response to lower body negative pressure stressor is altered.     

Can Insulated Skin Temperature Act as a Substitute for Rectal Temperature when Studying Circadian Rhythms?

We measured rectal, lateral chest wall, and axillary temperature every half hour for at least 24 h while subjects were living normal life-styles and keeping a sleep/activity diary. We then used a purification method to estimate the decrease of temperature due to sleep and the increases due to sitting, standing, walking, or exercising, as well as the parameters of the cosine curve that described the “purified data.” Cosinor analysis of raw and purified data showed that the acrophases from both skin sites were much more variable and up to 8 h later than were those from the rectum (particularly if exercise had been taken), even though the acrophases from the two skin sites were similar to each other. For rectal temperature, there was an increase in the size of the masking effect as activity progressed through the sequence: sitting, standing or walking, exercising. In contrast, for both chest wall and axillary temperatures, although sitting produced masking effects similar to those for rectal temperature, masking effects due to standing or walking and exercising were much smaller, and sometimes they were even less than the masking effects due to sitting. These results indicate that our measurements of cutaneous temperature did not act as a substitute for rectal temperature, particularly when the subject was physically active rather than sedentary.     

Function of otolith organ in goldfish revealed from analysis of eye movement induced by acceleration.

An otolith organ on ground behave as a detector of both gravity and linear acceleration, and play an important role in controlling posture and eye movement for tilt of the head or translational motion. On the other hand, a gravitational acceleration ingredient to an otolith organ disappears in microgravity environment. However, linear acceleration can be received by otolith organ and produce a sensation that is different from that on Earth. It is suggested that in microgravity signal from the otolith organ may cause abnormality of posture control and eye movement. Therefore, the central nervous system may re-interprets all output from the otolith organ to indicate linear motion. A study of eye movement has been done a lot as one of a reflection related to an otolith organ system. In this study, we examined function of otolith organ in goldfish revealed from analysis of eye movement induced by linear acceleration or the tilt of body. We analyzed both torsional and vertical eye movements from video images frame by frame. For tilting stimulation, torsional eye movements induced by head down was larger than that induced by head up for larger tilt angle than 30 degrees. In the case of linear acceleration below 0.4 G, however, no clear differences were observed in both torsional and vertical eye movement. These results suggest that body tilt and linear acceleration may not be with equivalent stimulation to cause eye movement on the ground.     

Wear Testing of Moderate Activities of Daily Living Using In Vivo Measured Knee Joint Loading

Resumption of daily living activities is a basic expectation for patients provided with total knee replacements. However, there is a lack of knowledge regarding the impact of different activities on the wear performance. In this study the wear performance under application of different daily activities has been analyzed. In vivo load data for walking, walking downstairs/upstairs, sitting down/standing up, and cycling (50 W & 120 W) has been standardized for wear testing. Wear testing of each activity was carried out on a knee wear simulator. Additionally, ISO walking was tested for reasons of comparison. Wear was assessed gravimetrically and wear particles were analyzed. In vivo walking produced the highest overall wear rates, which were determined to be three times higher than ISO walking. Moderate wear rates were determined for walking upstairs and downstairs. Low wear rates were determined for standing up/sitting down and cycling at power levels of 50 W and 120 W. The largest wear particles were observed for cycling. Walking based on in vivo data has been shown to be the most wear-relevant activity. Highly demanding activities (stair climbing) produced considerably less wear. Taking into account the expected number of loads, low-impact activities like cycling may have a greater impact on articular wear than highly demanding activities.     

Head mounted displays for capturing head kinematics in postural tasks

Tracking head motion in a simple, portable and accurate manner during performance of postural tasks in a virtual reality environment could have important implications for investigating normal and pathological head kinematics. We investigated concurrent validity of head tracking of two Head Mounted Displays (HMDs), Oculus Rift and HTC Vive, vs. a gold-standard motion capture system (Qualisys). Head kinematics of N = 20 healthy young adults was quantified during static and dynamic postural tasks. While wearing the Oculus Rift or HTC Vive, participants observed moving stars (static tasks) or a flying ball (dynamic task). Head kinematics were recorded simultaneously by the Rift or Vive and Qualisys camera system. We calculated head directional path, acceleration in 6 directions and volume of translation movement. Intra-Class Correlations (ICC) and 95% Limits of agreement were calculated. Most ICC values were around 0.9 with several at 0.99 indicating excellent agreement between the HMDs and Qualisys. Weaker agreement was observed for vertical displacement during a static task and moderate agreement was observed pitch and yaw displacement during a dynamic task. A negative bias of a small magnitude (indicating more movement in VR) was observed for most variables in static tasks, while a positive bias was observed for most variables in the dynamic task (indicating less movement in VR). Our results generally support the concurrent validity of Oculus Rift and HTC Vive head tracking during static and dynamic standing tasks in healthy young adults. Specific task- and direction-dependent differences should be considered when planning measurement studies using these novel tools.