Simultaneous utilization of pyridine and fructose by Rhodococcus opacus UFZ B 408 without an external nitrogen source

 A bacterium classified as Rhodococcus opacus, which is able to use pyridine (a potentially growth-inhibiting substrate) as its sole source of carbon, energy and nitrogen, was isolated. In a carbon-limited chemostat culture, the kinetics was determined for growth on both pyridine and a mixture of pyridine and fructose (9 mM/22.15 mM). With growth on pyridine, stable steady states were achieved up to dilution rates of about 0.1 h^-1. A further increase in the dilution rate resulted in the progressive accumulation of pyridine in the culture liquid and the cells were washed out. The maximum specific growth rate (μ_max = 0.23 h^-1) and the K _S value (0.22 mM) for growth on pyridine were determined from the residual pyridine concentrations measured within the range of stable steady states. With growth on the substrate mixture, the specific pyridine consumption rates and the residual pyridine concentrations were lower at similar dilution rates than with growth on pyridine alone, and stable steady states were established at dilution rates of up to 0.13 h^-1. The maximum pyridine degradation rate was enhanced to 270 mg pyridine l^-1 h^-1 compared to 210 mg pyridine l^-1 h^-1with growth on pyridine as a single substrate. An external nitrogen source did not need to be added in the case of growth on the substrate mixture. Fructose was assimilated by means of ammonium released from pyridine. Analysis of the nitrogen balance furnished proof that pyridine is an energy-deficient substrate; pyridine was assimilated and dissimilated at a ratio of 1 mol/0.67 mol respectively. The resulting yield coefficient was about 0.55 g dry weight/g pyridine. Moreover, it was demonstrated that, in regard to the biologically usable energy, 1 mol pyridine corresponds to 0.43 mol fructose. Received: 3 July 1995/Received revision: 19 October 1995/Accepted: 24 October 1995     

Effect of growth rate on the production of<Emphasis Type="SmallCaps">l</Emphasis>-proline in the fed-batch culture of<Emphasis Type="Italic">Corynebacterium acetoacidophilum</Emphasis>

Corynebacterium acetoacidophilum RYU3161 was cultivated in al-histidine-limited fed-batch culture. To investigate the effect of cell growth on thel-proline production, 5l fed-batch culture was performed using an exponential feeding rate to obtain the specific growth rates (μ) of 0.04, 0.06, 0.08, and 0.1 h⁻¹. The results show that the highest production ofl-proline was obtained at μ=0.04 h⁻¹. The specificl-proline production rate (Q_p) increased proportionally as a function of the specific growth rate, but decreased after it revealed the maximum value at μ=0.08 h⁻¹. Thus, the highest productivity ofl-proline was 1.66 g L⁻¹ h⁻¹ at μ=0.08 h⁻¹. The results show that the production of L-proline inC. acetoacidophilum RYU3161 has mixed growth-associated characteristics.     

Biological removal of inorganic Hg(II) as gaseous elemental Hg(0) by continuous culture of a Hg-resistant Pseudomonas putida strain FB-1

A strain of broad-spectrum, mercury-resistant Pseudomonas putida FB1 was used to remove mercury as the gaseous element (Hg(0)) from a continuous axenic culture, fed with a synthetic medium containing 1 mg Hg l^-1 as HgCl₂. Mercury determinations were performed in steady-state cultures using various culture fractions [whole culture, filtered supernatant, bacterial cells (dry wt), recovery trap liquid] in order to determine the removal efficiency at different dilution rates (from 0.1 to 3.0 day^-1). The removal efficiency ranged from 99.2% to 99.8%, and the residual Hg was maintained below 5 l^-1 (the maximum allowable concentration of Hg in liquid wastes according to Italian law) at a dilution rate of 1.0 day^-1, corresponding to a Hg flux of 40 g l^-1 h^-1. Hg accumulation by cell biomass was negligible for dilution rates under 1.0 day^-1. A progressive accumulation of Hg, both in the liquid phase and in cells, occurred at a higher dilution rate (3.0 day^-1; close to washout), corresponding to a Hg concentration of 25 g g^-1 (dry wt). The estimated K_m and V_max for Hg reduction were 0.241 mg l^-1 and 9.5 mg g^-1 h^-1, respectively. In batch experiments maximum Hg removal occurred at the optimum growth temperature (28°C) of P. putida. The maximum recovery of Hg in the liquid trap was 78%.     

Production of 1,3-Propanediol by Clostridium butyricum VPI 3266 in continuous cultures with high yield and productivity

The effects of dilution rate and substrate feed concentration on continuous glycerol fermentation by Clostridium butyricum VPI 3266, a natural 1,3-propanediol producer, were evaluated in this work. A high and constant 1,3-propanediol yield (around 0.65 mol/mol), close to the theoretical value, was obtained irrespective of substrate feed concentration or dilution rate. Improvement of 1,3-propanediol volumetric productivity was achieved by increasing the dilution rate, at a fixed feed substrate concentration of 30, 60 or 70 g l⁻¹. Higher 1,3-propanediol final concentrations and volumetric productivities were also obtained when glycerol feed concentration was increased from 30 to 60 g l⁻¹, at D=0.05–0.3 h⁻¹, and from 60–70 g l⁻¹, at D=0.05 and 0.1 h⁻¹·30 g l⁻¹ of 1,3-propanediol and the highest reported value of productivity, 10.3 g l⁻¹ h⁻¹, was achieved at D=0.30 h⁻¹ and 60 g l⁻¹ of feed glycerol. A switch to an acetate/butyrate ratio higher than one was observed for 60 g l⁻¹ of feed glycerol and a dilution rate higher than 0.10 h⁻¹; moreover, at D=0.30 h⁻¹ 3-hydroxypropionaldehyde accumulation was observed for the first time in the fermentation broth of C. butyricum.     

Enhanced l-lysine production in threonine-limited continuous culture of Corynebacterium glutamicum by using gluconate as a secondary carbon source with glucose

In order to improve the production rate of l-lysine, a mutant of Corynebacterium glutamicum ATCC 21513 was cultivated in complex medium with gluconate and glucose as mixed carbon sources. In a batch culture, this strain was found to consume gluconate and glucose simultaneously. In continuous culture at dilution rates ranging from 0.2 h⁻¹ to 0.25 h⁻¹, the specific l-lysine production rate increased to 0.12 g g⁻¹ h⁻¹ from 0.1 g g⁻¹ h⁻¹, the rate obtained with glucose as the sole carbon source [Lee et al. (1995) Appl Microbiol Biotechnol 43:1019–1027]. It is notable that l-lysine production was observed at higher dilution rates than 0.4 h⁻¹, which was not observed when glucose was the sole carbon source. The positive effect of gluconate was confirmed in the shift of the carbon source from glucose to gluconate. The metabolic transition, which has been characterized by decreased l-lysine production at the higher glucose uptake rates, was not observed when gluconate was added. These results demonstrate that the utilization of gluconate as a secondary carbon source improves the maximum l-lysine production rate in the threonine-limited continuous culture, probably by relieving the limiting factors in the lysine synthesis rate such as NADPH supply and/or phosphoenolpyruvate availability. Received: 16 May 1997 / Received revision: 28 August 1997 / Accepted: 29 August 1997     

Production of poly(3-hydroxyalkanoates) by Pseudomonas putida KT2442 in continuous cultures

 The synthesis of poly(3-hydroxyalkanoates) (PHA) by Pseudomonas putida KT2442 growing on long-chain fatty acids was studied in continuous cultures. The effects of the growth rate on the biomass and polymer concentration were determined and it was found that the PHA concentrations decreased with increasing growth rates. The highest volumetric productivity was 0.13 g PHA l^-1 h^-1 at a specific growth rate (μ) of 0.1 h^-1. The molecular mass of the polymer remained constant at all growth rates but changes in the monomeric composition of the PHA synthesized were observed. Variation of the carbon to nitrogen (C/N) ratio of the substrate feed at μ=0.1 h^-1 revealed optimal PHA formation at C/N=20 mol/mol. In order to optimize PHA production P. putida KT2442 was cultivated to high cell densities in oxygen-limited continuous cultures. In this way a maximum biomass concentration of 30 g/l containing approximately 23% PHA was achieved. This corresponds to a volumetric productivity of 0.69 g  l^-1 h^-1. Received: 14 December 1995 / Received revision: 18 April 1996 / Accepted: 22 April 1996     

Selection of an adhesive phenotype of Streptococcus salivarius subsp. thermophilus for use in fixed-bed reactors

 Streptococcus salivarius subsp. thermophilus was cultivated in a chemostat in order to obtain an adhesive phenotype of this strain. When the system was operated at low dilution rates (D<0.2 h^-1) for about 4 weeks, the strain formed a visible film on the surface of the culture vessel. The biofilm cells were not washed out even when dilution rates were increased (D=6.9 h^-1), and this resulted in a high biomass productivity (P=4.1 g l^-1h^-1). On the other hand, when the culture was grown at dilution rates faster than 0.2 h^-1, only the free suspended cells were present in the culture broth, and were washed out at velocities of about 1.0 h^-1. The biomass productivity was consequently lower (P=1.33 g l^-1h^-1) than in the previous case. The selected adhesive phenotype was grown on different glass beads and the possibility of lactate fermentation in a continuous and semicontinuous mode was demonstrated. Received: 16 August 1995/Received revision: 18 March 1996/Accepted: 25 March 1996     

Production of 1,3-propanediol by Clostridium butyricum in continuous culture with cell recycling

The continuous fermentation of 1,3-propanediol from glycerol by Clostridium butyricum was subjected to cell recycling by filtration using hollow-fibre modules made from polysulphone. The performance of the culture system was checked at a retention ratio (dilution rate/bleed rate) of 5, dilution rates between 0.2 h⁻¹ and 1.0 h⁻¹ and glycerol input concentrations of 32 g l⁻¹ and 56 g l⁻¹. The near-to-optimum propanediol concentration of 26.5 g l⁻¹ (for 56 g l⁻¹ glycerol) was maintained up to a dilution rate of 0.5 h⁻¹ and then decreased while the propanediol productivity was highest at 0.7 h⁻¹. The productivity could be increased by a factor of four in comparison to the continuous culture without cell recycling. By application of the model of Zeng and Deckwer [(1995) Biotechnol Prog 11: 71–79] for cultures under substrate excess, it was shown that the limitations resulted exclusively from product inhibition and detrimental influences from the cell recycling system, such as shear stress, were not involved. Received: 20 October 1997 / Received revision: 12 December 1997 / Accepted: 14 December 1997     

Application of oscillation for efficiency improvement of continuous ethanol fermentation with Saccharomyces cerevisiae under very-high-gravity conditions

Compared with steady state, oscillation in continuous very-high-gravity ethanol fermentation with Saccharomyces cerevisiae improved process productivity, which was thus introduced for the fermentation system composed of a tank fermentor followed by four-stage packed tubular bioreactors. When the very-high-gravity medium containing 280 g l⁻¹ glucose was fed at the dilution rate of 0.04 h⁻¹, the average ethanol of 15.8% (v/v) and residual glucose of 1.5 g l⁻¹ were achieved under the oscillatory state, with an average ethanol productivity of 2.14 g h⁻¹ l⁻¹. By contrast, only 14.8% (v/v) ethanol was achieved under the steady state at the same dilution rate, and the residual glucose was as high as 17.1 g l⁻¹, with an ethanol productivity of 2.00 g h⁻¹ l⁻¹, indicating a 7% improvement under the oscillatory state. When the fermentation system was operated under the steady state at the dilution rate of 0.027 h⁻¹ to extend the average fermentation time to 88 h from 59 h, the ethanol concentration increased slightly to 15.4% (v/v) and residual glucose decreased to 7.3 g l⁻¹, correspondingly, but the ethanol productivity was decreased drastically to 1.43 g h⁻¹ l⁻¹, indicating a 48% improvement under the oscillatory state at the dilution rate of 0.04 h⁻¹.     

Protein production from whey usingPenicillium cyclopium; growth parameters and cellular composition

Summary The growth parameters ofPenicillium cyclopium have been evaluated in a continuous culture system for the production of fungal protein from whey. Dilution rates varied from 0.05 to 0.20 h^–1 under constant conditions of temperature (28°C) and pH (3.5). The saturation coefficients in the Monod equation were 0.74 g l^–1 for lactose and 0.14 mg l^–1 for oxygen, respectively. For a wide range of dilution rates, the yield was 0.68 g g^–1 biomass per lactose and the maintenance coefficient 0.005 g g^–1 h^–1 lactose per biomass, respectively. The maximum biomass productivity achieved was 2 g l^–1 h^–1 biomass at dilution rates of 0.16–0.17 h^–1 with a lactose concentration of 20 g l^–1 in the feed. The crude protein and total nucleic acid contents increased with a dilution rate, crude protein content varied from 43% to 54% and total nucleic acids from 6 to 9% in the range of dilution rates from 0.05 to 0.2 h^–1, while the Lowry protein content was almost constant at approximately 37.5% of dry matter.Nomenclature (mg l^–1) C_o initial concentration of dissolved oxygen - (h^–1) D dilution rate - (mg l^–1) K₀₂ saturation coefficient for oxygen - (g l^–1) K_s saturation coefficient for substrate - (g g^–1 h^–1) lactose per biomass) m maintenance energy coefficient - (mM g^–1 h^–1O₂ per biomass) Q₀₂ specific oxygen uptake rate - (g l^–1) S residual substrate concentration at steady state - (g l^–1) S_o initial substrate concentration in feed - (min) t_1/2 time when C_o is equal to C_o/2 - (g l^–1) X biomass concentration - (g l^–1) X biomass concentration at steady state - (g g^–1 biomass per lactose) Y_G yield coefficient for cell growth - (g g^–1 biomass per lactose) Y_x/s overall yield coefficient - (h^–1) specific growth rate     

Optimising enzyme production by bakers yeast in continuous culture: physiological knowledge useful for process design and control

Saccharomyces cerevisiae was grown in aerobic continuous culture on a defined minimal medium, with glucose (40 g.l⁻¹) as the growth-limiting carbon source, to acquire knowledge useful in process design and for model-based control. Steady-state concentrations of biomass, glucose, ethanol and activities of model products alcohol dehydrogenase, hexokinase, malate dehydrogenase, glucose-6-phosphate dehydrogenase and iso-citrate dehydrogenase were determined at dilution rates (D) between 0.06 h⁻¹ and 0.323 h⁻¹ (close to μ_max). Enzyme activities showed productivity trends related to the transition from oxidative to oxido-reductive growth. Conclusions are drawn from the data with regard to designing a new process for production of intracellular enzymes. Issues of process stability as well as productivity are discussed.     

Invertase and phosphatase of yeast in a phosphate-limited continuous culture

Summary Deficiency of inorganic phosphate caused the hyper production of invertase and the derepression of acid phosphatase in a continuous culture ofSaccharomyces carlsbergensis. The specific invertase activity was 40,000 enzyme units per g dry cell weight at a dilution rate lower than 0.05 h^–1 with a synthetic glucose medium of which the molecular ratio of KH₂PO₄ to glucose was less than 0.006. This activity is eight fold higher than in a batch growth and 1.5 fold as much as the highest enzyme activity observed so far in a glucose-limited continuous culture.For the hyper production of invertase, it is necessary to culture the yeast continuously by keeping the Nyholm's conservative inorganic phosphate concentration at less than 0.2 m mole per g dry weight cell. The derepression of acid phosphatase brought about by phosphate deficiency, was similar in both batch and continuous cultures.Nomenclature D dilution rate of continuous culture (h^–1) - E_i invertase concentration in culture (enzyme unit l^–1) - E_p acid phosphatase concentration in culture (enzyme unit l^–1) - P inorganic phosphate concentration in culture (mM) - S glucose concentration in culture (mM) - X cell concentration in culture (g dry weight cell l^–1) Greek Letter specific rate of growth (h^–1) Suffix f feed - 0 initial value     

Characterisation of kinetic parameters and metabolic transition of Corynebacterium glutamicum on l-lysine production in continuous culture

Kinetic parameters and physiological states of Corynebacterium glutamicum at the growing and l-lysine-overproducing phase were characterised in continuous culture on threonine-limited complex and minimal media. High l-lysine productivity occurred at dilution rates ranging from 0.1 h^–1 to 0.3 h^–1 on threonine-limited complex medium, and at dilution rates ranging from 0.1 h^–1 to 0.15 h^–1 in minimal medium. l-Lysine yields of 0.25 g/g (0.31 g/g as l-lysine hydrochloride) in complex medium, and of 0.17 g/g (0.21 g/g as l-lysine hydrochloride) in minimal medium, corresponding respectively to intrinsic yields of 0.533 g/g and 0.572 g/g were obtained. These intrinsic yield factors are closed to the theoretical ones (0.608 g/g, 0.75 mol/mol). Intrinsic biomass yields were calculated as 0.658 g/g in complex medium and 0.283 g/g in minimal medium. CO₂ production has been clearly related to l-lysine production. According to our results on specific uptake rates and specific productivities in complex medium, metabolic rearrangement should occur during the transition from the growing phase to the l-lysine-overproducing phase. This phenomenon was further investigated.     

The isolation and characterisation of a salicylate-hydroxylase-producing strain of Pseudomonas putida

Summary A salicylate-hydroxylase-producing strain of Pseudomonas putida with an unusual capability to grow at toxic levels of salicylate up to 10 g l^–1 has been isolated. It grew well under continuous culture conditions, with optimum growth at pH 6.5 and a temperature of 25° C. The use of an ammonium salt as a nitrogen source, instead of nitrate, resulted in a 30–40% increase in its biomass yield coefficient. Optimum growth under continuous culture conditions was achieved using 4 g l^–1 salicylate at 25° C, pH 6.5 and 0.2 h^–1 dilution rate. High salicylate hydroxylase enzyme activity [236 units (U) l^–1] and productivity (424.8 U h^–1) were obtained at a dilution rate of 0.45 h^–1 using a mineral medium containing 4 g l^–1 of salicylate. Operating under continuous culture conditions with oxygen limitation and a slight accumulation of residual salicylate (0.2 g l^–1) resulted in a decrease in culture performance and enzyme productivity. Correspondence to: R. Marchant     

Production of lipase by high cell density fed-batch culture of Candida cylindracea

Candida cylindracea NRRL Y-17506 was grown to produce extracellular lipase from oleic acid as a carbon source. Through flask cultures, it was found that the optimum initial oleic acid concentration for cell growth was 20 g l⁻¹. However, high initial concentrations of oleic acid up to 50 g l⁻¹ were not inhibitory. The highest extracellular lipase activity obtained in flask culture was 3.0 U ml⁻¹ after 48 h with 5 g l⁻¹ of initial oleic acid concentration. Fed-batch cultures (intermittent and stepwise feeding) were carried out to improve cell concentration and lipase activity. For the intermittent feeding fed-batch culture, the final cell concentration was 52 g l⁻¹ and the extracellular lipase activity was 6.3 U ml⁻¹ at 138.5 h. Stepwise feeding fed-batch cultures were carried out to simulate an exponential feeding and to investigate the effects of specific growth rate (0.02, 0.04 and 0.08 h⁻¹) on cell growth and lipase production. The highest final cell concentration obtained was 90 g l⁻¹ when the set point of specific growth rate (μ_set) was 0.02 h⁻¹. High specific growth rate (0.04 and 0.08 h⁻¹) decreased extracellular lipase production in the later part of fed-batch cultures due to build-up of the oleic acid oversupplied. The highest extracellular lipase activity was 23.7 U ml⁻¹ when μ_set was 0.02 h⁻¹, while the highest lipase productivity was 0.31 U ml⁻¹ h⁻¹ at μ_set of 0.08 h⁻¹.     

Effects of methanol on expression of an anticoagulant hirudin in recombinant Hansenula polymorpha

A series of batch, fed-batch, and continuous cultures was carried out to analyze the effects of methanol on the fermentation characteristics of recombinant Hansenula polymorpha for the production of hirudin, an anticoagulant. Hirudin expression efficiencies were greatly influenced by the methanol concentrations in continuous and fed-batch culture modes. At a steady state of continuous culture, an optimum methanol concentration of 1.7 g l⁻¹ was determined at a dilution rate of 0.18 h⁻¹ with 1.8 mg l⁻¹ h⁻¹ hirudin productivity. Journal of Industrial Microbiology & Biotechnology (2001) 27, 58–61. Received 21 September 2000/ Accepted in revised form 10 June 2001     

Continuous nisin production with bioengineered <Emphasis Type="Italic">Lactococcus lactis</Emphasis> strains

Nisin production in continuous cultures of bioengineered Lactococcus lactis strains that incorporate additional immunity and regulation genes was studied. Highest nisin activities were observed at 0.2 h^–1 dilution rate and 12.5 g l^–1 fructose concentration for all strains. Recombinant strains were able to produce greater amounts of nisin at dilution rates below 0.3 h⁻¹ compared to the control strain. However, this significant difference disappeared at dilution rates of 0.4 and 0.5 h^–1. For the strains LL27, LAC338, LAC339, and LAC340, optimum conditions for nisin production were determined to be at 0.29, 0.26, 0.27, and 0.27 h^–1 dilution rates and 11.95, 12.01, 11.63, and 12.50 g l^–1 fructose concentrations, respectively. The highest nisin productivity, 496 IU ml^–1 h^–1, was achieved with LAC339. The results of this study suggest that low dilution rates stabilize the high specific nisin productivity of the bioengineered strains in continuous fermentation. Moreover, response surface methodology analysis showed that regulation genes yielded high nisin productivity at wide ranges of dilution rates and fructose concentrations.     

Hydrogen production with high yield and high evolution rate by self-flocculated cells of Enterobacter aerogenes in a packed-bed reactor

Continuous hydrogen gas evolution by self-flocculated cells of Enterobacter aerogenes, a natural isolate HU-101 and its mutant AY-2, was performed in a packed-bed reactor under glucose-limiting conditions in a minimal medium. The flocs that formed during the continuous culture were retained even when the dilution rate was increased to 0.9 h⁻¹. The H₂ production rate increased linearly with increases in the dilution rate up to 0.67 h⁻¹, giving maximum H₂ production rates of 31 and 58 mmol l⁻¹ h⁻¹ in HU-101 and AY-2 respectively, at a dilution rate of more than 0.67 h⁻¹. The molar H₂ yield from glucose in AY-2 was maintained at about 1.1 at dilution rates between 0.08 h⁻¹ and 0.67 h⁻¹, but it decreased rapidly at dilution rates more than 0.8 h⁻¹. Received: 27 August 1997 / Received revision: 11 November 1997 / Accepted: 14 December 1997     

Benzene Degradation Coupled with Chlorate Reduction in a Soil Column Study

Perchlorate and chlorate are electron acceptors that during reduction result in the formation of molecular oxygen. The produced oxygen can be used for activation of anaerobic persistent pollutants, like benzene. In this study chlorate was tested as potential electron acceptor to stimulate benzene degradation in anoxic polluted soil column. A chlorate amended benzene polluted soil column was operated over a period of 500 days. Benzene was immediately degraded in the column after start up, and benzene removal recovered completely after omission of chlorate or a too high influent chlorate concentration (22 mM). Mass balance calculations showed that per mole of benzene five mole of chlorate were reduced. At the end of the experiment higher loading rates were applied to measure the maximal benzene degradation rate in this system; a breakthrough of benzene was not observed. The average benzene degradation rate over this period was 31 μmol l⁻¹ h⁻¹ with a maximal of 78 μmol l⁻¹ h⁻¹. The high degradation rate and the necessity of chlorate indicate that oxygen produced during chlorate reduction indeed is used for the activation of benzene. This is the first column study where benzene biodegradation at a high rate coupled with anaerobic chlorate reduction is observed.     

L-Sorbose production in a continuous fermenter with and without cell recycle

The kinetics of continuous l-sorbose fermentation using Acetobacter suboxydans with and without cell recycle (100%) were investigated at dilution rates (D) of 0.05, 0.10, 0.15 and 0.3 h^–1. The biomass and sorbose concentrations for continuous fermentation without recycle increased as the dilution rate was increased from 0.05 to 0.10 h^–1. A maximum biomass concentration of 8.44 g l^–1 and sorbose concentration of 176.90 g l^–1 were obtained at D=0.10 h^–1. The specific rate of sorbose production and volumetric sorbose productivity at this dilution rate were 2.09 g g^–1 h^–1 and 17.69 g l^–1 h^–1. However, on further increasing the dilution rate to 0.3 h^–1, both biomass and sorbose concentrations decreased to 2.93 and 73.20 g l^–1 respectively, mainly due to washout of the reactor contents. However, the specific rate of sorbose formation and volumetric sorbose productivity at this dilution rate increased to 7.49 g g^–1 h^–1 and 21.96 g l^–1 h^–1 respectively. Continuous fermentation with 100% cell recycle served to further enhance the concentration of biomass and sorbose to 28.27 and 184.32 g l^–1 respectively (in the reactor at a dilution rate of 0.05 h^–1). Even though, there was a decline in the biomass and sorbose concentrations to 6.8 and 83.40 g l^–1 at a dilution rate of 0.3 h^–1, the specific rates of sorbose formation and volumetric sorbose productivity increased to 3.67 g g^–1h^–1 and 25.02 g l^–1 h^–1.