Effect of controlled oxygen limitation on Candida shehatae physiology for ethanol production from xylose and glucose

Carbon distribution and kinetics of Candida shehatae were studied in fed-batch fermentation with xylose or glucose (separately) as the carbon source in mineral medium. The fermentations were carried out in two phases, an aerobic phase dedicated to growth followed by an oxygen limitation phase dedicated to ethanol production. Oxygen limitation was quantified with an average specific oxygen uptake rate (OUR) varying between 0.30 and 2.48 mmolO₂ g dry cell weight (DCW)^?1 h^?1, the maximum value before the aerobic shift. The relations among respiration, growth, ethanol production and polyol production were investigated. It appeared that ethanol was produced to provide energy, and polyols (arabitol, ribitol, glycerol and xylitol) were produced to reoxidize NADH from assimilatory reactions and from the co-factor imbalance of the two-first enzymatic steps of xylose uptake. Hence, to manage carbon flux to ethanol production, oxygen limitation was a major controlled parameter; an oxygen limitation corresponding to an average specific OUR of 1.19 mmolO₂ g DCW^?1 h^?1 allowed maximization of the ethanol yield over xylose (0.327 g g^?1), the average productivity (2.2 g l^?1 h^?1) and the ethanol final titer (48.81 g l^?1). For glucose fermentation, the ethanol yield over glucose was the highest (0.411 g g^?1) when the specific OUR was low, corresponding to an average specific OUR of 0.30 mmolO₂ g DCW^?1 h^?1, whereas the average ethanol productivity and ethanol final titer reached the maximum values of 1.81 g l^?1 h^?1 and 54.19 g l^?1 when the specific OUR was the highest.     

Kinetics of growth and ethanol formation from a mix of glucose/xylose substrate by Kluyveromyces marxianus UFV-3

The fermentation of both glucose and xylose is important to maximize ethanol yield from renewable biomass feedstocks. In this article, we analyze growth, sugar consumption, and ethanol formation by the yeast Kluyveromyces marxianus UFV-3 using various glucose and xylose concentrations and also under conditions of reduced respiratory activity. In almost all the conditions analyzed, glucose repressed xylose assimilation and xylose consumption began after glucose had been exhausted. A remarkable difference was observed when mixtures of 5 g L^?1 glucose/20 g L^?1 xylose and 20 g L^?1 glucose/20 g L^?1 xylose were used. In the former, the xylose consumption began immediately after the glucose depletion. Indeed, there was no striking diauxic phase, as observed in the latter condition, in which there was an interval of 30 h between glucose depletion and the beginning of xylose consumption. Ethanol production was always higher in a mixture of glucose and xylose than in glucose alone. The highest ethanol concentration (8.65 g L^?1) and cell mass concentration (4.42 g L^?1) were achieved after 8 and 74 h, respectively, in a mixture of 20 g L^?1 glucose/20 g L^?1 xylose. When inhibitors of respiration were added to the medium, glucose repression of xylose consumption was alleviated completely and K. marxianus was able to consume xylose and glucose simultaneously.     

Evaluation of fermentative potential of <Emphasis Type="Italic">Kluyveromyces marxianus</Emphasis> ATCC 36907 in cellulosic and hemicellulosic sugarcane bagasse hydrolysates on xylitol and ethanol production

This paper evaluates the fermentative potential of Kluyveromyces marxianus grown in sugarcane bagasse cellulosic and hemicellulosic hydrolysates obtained by acid hydrolysis. Ethanol was obtained from a single glucose fermentation product, whereas xylose assimilation resulted in xylitol as the main product and ethanol as a by-product derived from the metabolism of this pentose. Fermentation performed in a simulated hydrolysate medium with a glucose concentration similar to that of the hydrolysate resulted in ethanol productivity (Qp?=?0.86 g L^?1 h^?1) that was tenfold higher than the one observed in the cellulosic hydrolysate. However, the use of hemicellulosic hydrolysate favored xylose assimilation in comparison with simulated medium with xylose and glucose concentrations similar to those found in this hydrolysate, without toxic compounds such as acetic acid and phenols. Under this condition, xylitol yield was 53.8 % higher in relation to simulated medium. Thus, the total removal of toxic compounds from the hydrolysate is not necessary to obtain bioproducts from lignocellulosic hydrolysates.     

Co-generation of ethanol and <Emphasis Type="SmallCaps">l</Emphasis>-lactic acid from corn stalk under a hybrid process

Background

Corn stover, as one important lignocellulosic material, has characteristics of low price, abundant output and easy availability. Using corn stover as carbon source in the fermentation of valuable organic chemicals contributes to reducing the negative environmental problems and the cost of production. In ethanol fermentation based on the hydrolysate of corn stover, the conversion rate of fermentable sugars is at a low level because the native S. cerevisiae does not utilize xylose. In order to increase the conversion rate of fermentable sugars deriving from corn stover, an effective and energy saving biochemical process was developed in this study and the residual xylose after ethanol fermentation was further converted to l-lactic acid.

Results

In the hybrid process based on the hydrolysate of corn stover, the ethanol concentration and productivity reached 50.50 g L^?1 and 1.84 g L^?1 h^?1, respectively, and the yield of ethanol was 0.46 g g^?1. The following fermentation of l-lactic acid provided a product titer of 21.50 g L^?1 with a productivity of 2.08 g L^?1 h^?1, and the yield of l-lactic acid was 0.76 g g^?1. By adopting a blank aeration before the inoculation of B. coagulans LA1507 and reducing the final cell density, the l-lactic acid titer and yield reached 24.25 g L^?1 and 0.86 g g^?1, respectively, with a productivity of 1.96 g L^?1 h^?1.

Conclusions

In this work, the air pumped into the fermentor was used as both the carrier gas for single-pass gas stripping of ethanol and the oxygen provider for the aerobic growth of B. coagulans LA1507. Ethanol was effectively separated from the fermentation broth, while the residual medium containing xylose was reused for l-lactic acid production. As an energy-saving and environmental-friendly process, it introduced a potential way to produce bioproducts under the concept of biorefinery, while making full use of the hydrolysate of corn stover.

     

Production of butanol and isopropanol with an immobilized <Emphasis Type="Italic">Clostridium</Emphasis>

Clostridium beijerinckii optinoii is a Clostridium species that produces butanol, isopropanol and small amounts of ethanol. This study compared the performances of batch and continuous immobilized cell fermentations, investigating how media flow rates and nutritional modification affected solvent yields and productivity. In 96-h batch cultures, with 80 % of the 30 g L^?1 glucose consumed in synthetic media, solvent concentration was 9.45 g L^?1 with 66.0 % as butanol. In a continuous fermentation using immobilized C. beijerinckii optinoii cells, also with 80 % of 30 g L^?1 glucose utilization, solvent productivity increased to 1.03 g L^?1 h^?1. Solvent concentration reached 12.14 g L^?1 with 63.0 % as butanol. Adjusting the dilution rate from 0.085 to 0.050 h^?1 to allow extended residence time in column was required when glucose concentration in fresh media was increased from 30 to 50 g L^?1. When acetate was used to improve the buffer capacity in media, the solvent concentration reached 12.70 on 50 g L^?1 glucose. This continuous fermentation using immobilized cells showed technical feasibility for solvent production.     

Polyhydroxyalkanoate biosynthesis and simultaneous remotion of organic inhibitors from sugarcane bagasse hydrolysate by Burkholderia sp.

Burkholderia sp. F24, originally isolated from soil, was capable of growth on xylose and removed organic inhibitors present in a hemicellulosic hydrolysate and simultaneously produced poly-3-hydroxybutyrate (P3HB). Using non-detoxified hydrolysate, Burkholderia sp. F24 reached a cell dry weight (CDW) of 6.8 g L^?1, containing 48 % of P3HB and exhibited a volumetric productivity (P_P3HB) of 0.10 g L^?1 h^?1. Poly-3-hydroxybutyrate-co-3-hydroxyvalerate copolymers (P3HB-co-3HV) were produced using xylose and levulinic acid (LA) as carbon sources. In shake flask cultures, the 3HV content in the copolymer increased from 9 to 43 mol% by adding LA from 1.0 to 5.0 g L^?1. In high cell density cultivation using concentrated hemicellulosic hydrolysate F24 reached 25.04 g L^?1 of CDW containing 49 % of P3HB and P_P3HB of 0.28 g L^?1 h^?1. Based on these findings, second-generation ethanol and bioplastics from sugarcane bagasse is proposed.     

Evaluation of ethanol production by a new isolate of yeast during fermentation in synthetic medium and sugarcane bagasse hemicellulosic hydrolysate

A new xylose fermenting yeast was isolated from over-ripe banana by enrichment in xylose-containing medium. The phylogenetic analysis of ITS1-5.8S-ITS2 region sequences of ribosomal RNA of isolate BY2 revealed that it shows affiliation to genus Pichia and clades with Pichia caribbica. In batch fermentation, Pichia strain BY2 fermented xylose, producing 15 g l^?1 ethanol from 30 g l^?1 xylose under shaking conditions at 28°C, with ethanol yield of 0.5 g g^?1 and volumetric productivity of 0.31 g l^?1 h^?1. The optimum pH range for ethanol production from xylose by Pichia strain BY2 was 5–7. Pichia strain BY2 also produced 6.08 g l^?1 ethanol from 30 g l^?1 arabinose. Pichia strain BY2 can utilize sugarcane bagasse hemicellulose acid hydrolysate for alcohol production, efficiency of fermentation was improved by neutralization, and sequential use of activated charcoal adsorption method. Percent total sugar utilized and ethanol yield for the untreated hydrolysate was 17.14% w/v and 0.33 g g^?1, respectively, compared with 66.79% w/v and 0.45 g g^?1, respectively, for treated hemicellulose acid hydrolysate. This new yeast isolate showed ethanol yield of 0.45 g g^?1 and volumetric productivity of 0.33 g l^?1 h^?1 from sugarcane bagasse hemicellulose hydrolysate detoxified by neutralization and activated charcoal treatment, and has potential application in practical process of ethanol production from lignocellulosic hydrolysate.     

Enhanced citric acid production by a yeast <Emphasis Type="Italic">Yarrowia lipolytica</Emphasis> over-expressing a pyruvate carboxylase gene

In this study, after the expression of a pyruvate carboxylase gene (PYC) cloned from Meyerozyma guilliermondii in a marine-derived yeast Yarrowia lipolytica SWJ-1b, a transformant PG86 obtained had much higher PYC activity than Y. lipolytica SWJ-1b. At the same time, the PYC gene expression and citric acid (CA) production by the transformant PG86 were also greatly enhanced. When glucose concentration in the medium was 60.0 g L^?1, CA concentration formed by the transformant PG86 was 34.02 g L^?1, leading to a CA yield of 0.57 g g^?1 of glucose. During a 10-L fed-batch fermentation, the final concentration of CA was 101.0 ± 1.3 g L^?1, the yield was 0.89 g g^?1 of glucose, the productivity was 0.42 g L^?1 h^?1 and only 5.93 g L^?1 reducing sugar was left in the fermented medium within 240 h of the fed-batch fermentation. HPLC analysis showed that most of the fermentation products were CA.     

Improved production of <Emphasis Type="Italic">Oroxylum indicum</Emphasis> (L.) Kurz by altering the salts of the medium

The present study was conducted to test the effects of KNO₃, KH₂PO₄, and CaCl₂ on shoot multiplication, root proliferation, and accumulation of phytochemicals in in vitro cultures of Oroxylum indicum. The results indicate that modifying the MS salt formulation in relation to particular inorganic nutrients highly affected shoot multiplication, root proliferation, and accumulation of flavonoids in in vitro cultures. A concentration of 0.60 g L^?1 CaCl₂ resulted in the highest frequency of shoot regeneration (5.6 shoots per explant). A concentration of 0.40 g L^?1 CaCl₂ resulted in the highest frequency of root regeneration (7.8 roots per shoot). Modifications of the concentrations of inorganic salts were also found to be advantageous for production media for both multiple shoots and shoot-derived root in vitro cultures. Multiple shoots generated on shoot induction medium with a concentration of 0.60 g L^?1 CaCl₂ and roots generated on root induction medium with a concentration of 1.5 g L^?1 KNO₃ yielded about a five times higher flavonoid level than cultures generated on control medium respectively.     

Xylitol production by genetically modified industrial strain of <Emphasis Type="Italic">Saccharomyces cerevisiae</Emphasis> using glycerol as co-substrate

Xylitol is commercially used in chewing gum and dental care products as a low calorie sweetener having medicinal properties. Industrial yeast strain of S. cerevisiae was genetically modified to overexpress an endogenous aldose reductase gene GRE3 and a xylose transporter gene SUT1 for the production of xylitol. The recombinant strain (XP-RTK) carried the expression cassettes of both the genes and the G418 resistance marker cassette KanMX integrated into the genome of S. cerevisiae. Short segments from the 5′ and 3′ delta regions of the Ty1 retrotransposons were used as homology regions for integration of the cassettes. Xylitol production by the industrial recombinant strain was evaluated using hemicellulosic hydrolysate of the corn cob with glucose as the cosubstrate. The recombinant strain XP-RTK showed significantly higher xylitol productivity (212 mg L^?1 h^?1) over the control strain XP (81 mg L^?1 h^?1). Glucose was successfully replaced by glycerol as a co-substrate for xylitol production by S. cerevisiae. Strain XP-RTK showed the highest xylitol productivity of 318.6 mg L^?1 h^?1 and titre of 47 g L^?1 of xylitol at 12 g L^?1 initial DCW using glycerol as cosubstrate. The amount of glycerol consumed per amount of xylitol produced (0.47 mol mol^?1) was significantly lower than glucose (23.7 mol mol^?1). Fermentation strategies such as cell recycle and use of the industrial nitrogen sources were demonstrated using hemicellulosic hydrolysate for xylitol production.     

Bioprospecting of thermo- and osmo-tolerant fungi from mango pulp–peel compost for bioethanol production

The persistent edaphic stress on microbial succession due to dynamic changes during composting was explored for selection of multi-stress tolerant microbe(s) desirable for ethanol production. A total of 23 strains were isolated from mango compost using four successive enrichments in YP broth (g l^?1): glucose, 100; 150; 250 with ethanol (40) and cycloheximide (0.4) at 40 °C, pH 6.0. Based on multi-gene ribotyping, 14 yeasts (61 %) of Saccharomycetaceae, 2 filamentous fungi (8.6 %) and 7 bacteria (30.4 %) were obtained. Phenetic and phylogenetic analysis of the 14 yeasts revealed 64.3 % tolerant to 500 g l^?1 glucose, growth at 45 °C and resemblance to Candida sp. (14.3 %), Kluyveromyces marxianus (35.7 %), Pichia kudriavzevii (21.4 %) and Saccharomyces cerevisiae (28.6 %). Assessment of the 14 yeasts in glucose fermentation medium (pH 4.5 at 40 °C) showed ethanol productivity of ≥92 % by 12 yeasts with theoretical yields of 90–97 %. Fermentation of molasses (150 g l^?1 glucose equivalent) by P. kudriavzevii D1C at 40 °C resulted in 73.70 ± 0.02 g l^?1 ethanol and productivity of 4.91 ± 0.01 g l^?1 h^?1. Assessment of P. kudriavzevii D1C revealed multi-stress tolerance towards 5-hydroxymethyl furfural, ethanol (20 %, v/v), high gravity and H₂O₂ (0.3 M) indicating suitability for ethanol production using high gravity molasses and pre-treated lignocellulosic biomass fermentation.     

Continuous succinic acid production from xylose by <Emphasis Type="Italic">Actinobacillus succinogenes</Emphasis>

Continuous, anaerobic fermentations of D-xylose were performed by Actinobacillus succinogenes 130Z in a custom, biofilm reactor at dilution rates of 0.05, 0.10 and 0.30 h^?1. Succinic acid yields on xylose (0.55–0.68 g g^?1), titres (10.9–29.4 g L^?1) and productivities (1.5–3.4 g L^?1 h^?1) were lower than those of a previous study on glucose, but product ratios (succinic acid/acetic acid = 3.0–5.0 g g^?1) and carbohydrate consumption rates were similar. Also, mass balance closures on xylose were up to 18.2 % lower than those on glucose. A modified HPLC method revealed pyruvic acid excretion at appreciable concentrations (1.2–1.9 g L^?1) which improved the mass balance closure by up to 16.8 %. Furthermore, redox balances based on the accounted xylose consumed and the excreted metabolites, indicated an overproduction of reducing power. The oxidative pentose phosphate pathway was shown to be a plausible source of the additional reducing power.     

Optimal C:N ratio for the production of red pigments by Monascus ruber

The carbon-to-nitrogen (C:N) ratio in the biomass of microfungi tends to be quite different (e.g. 10–15) compared with the C:N ratio in the red pigments (e.g. >20) of the fungus Monascus ruber. Therefore, determining an optimal C:N ratio in the culture medium for maximizing the production of the pigments is important. A culture medium composition is established for maximizing the production of the red pigment by the fungus M. ruber ICMP 15220 in submerged culture. The highest volumetric productivity of the red pigment was 0.023 AU L^?1 h^?1 in a batch culture (30 °C, initial pH of 6.5) with a defined medium of the following composition (g L^?1): glucose (10), monosodium glutamate (MSG) (10), MgSO₄·7H₂O (0.5), KH₂PO₄ (5), K₂HPO₄ (5), ZnSO₄·7H₂O (0.01), FeSO₄·7H₂O (0.01), CaCl₂ (0.1), MnSO₄·H₂O (0.03). This medium formulation had a C:N mole ratio of 9:1. Under these conditions, the specific growth rate of the fungus was 0.043 h^?1 and the peak biomass concentration was 6.7 g L^?1 in a 7-day culture. The biomass specific productivity of the red pigment was 1.06 AU g^?1 h^?1. The best nitrogen source proved to be MSG although four other inorganic nitrogen sources were evaluated.     

Culture Media Statistical Optimization for Biomass Production of a Ligninolytic Fungus for Future Rice Straw Degradation

The main objective of this study was to optimize a culture media for low scale biomass production of Pleurotus spp. Future applications of this optimization will be implemented for “in situ” rice straw degradation, increase soil nutrients availability, and lower residue and rice culture management costs. Soil samples were taken from different points in six important rice production cities in Colombia. For carbon and nitrogen source selection a factorial 4² design was carried out. The Plackett-Burman design permitted to detect carbon, nitrogen and inducer effects on fungus growth (response variable for all designs). This optimization was carried out by a Box-Behnken design. Finally a re-optimization assay for glucose concentration was performed by means of a One Factor design. Only 4/33 (12 %) isolates showed and important laccase or manganese peroxidase activity compared to Pleurotus ostreatus (HPB/P3). We obtained an increased biomass production in Pleurotus spp. (T1.1.) with glucose, followed by rice husk. Rice straw was considered an inducing agent for lignin degradation. Glucose was a significant component with positive effects, whereas Tween 80 and pH had negative effects. On the contrary, rice husk, yeast extract and CaCl₂ were not significant components for increase the biomass production. Final media composition consisted of glucose 25 g L^?1, yeast extract 5 g L^?1, Tween 80 0.38 % (v/v), Rice husk 10 g L^?1, CaCl₂ 1 g L^?1, and pH 4.88 ± 0.2. The Box-Behnken polynomial prediction resulted to be lower than the experimental validation of the model (6.59 vs. 6.91 Log₁₀ CFU ml^?1 respectively).     

Butanol production from concentrated lactose/whey permeate: Use of pervaporation membrane to recover and concentrate product

In these studies, butanol (acetone butanol ethanol or ABE) was produced from concentrated lactose/whey permeate containing 211 g L^?1 lactose. Fermentation of such a highly concentrated lactose solution was possible due to simultaneous product removal using a pervaporation membrane. In this system, a productivity of 0.43 g L^?1 h^?1 was obtained which is 307 % of that achieved in a non-product removal batch reactor (0.14 g L^?1 h^?1) where approximately 60 g L^?1 whey permeate lactose was fermented. The productivity obtained in this system is much higher than that achieved in other product removal systems (perstraction 0.21 g L^?1 h^?1 and gas stripping 0.32 g L^?1 h^?1). This membrane was also used to concentrate butanol from approximately 2.50 g L^?1 in the reactor to 755 g L^?1. Using this membrane, ABE selectivities and fluxes of 24.4–44.3 and 0.57–4.05 g m^?2 h^?1 were obtained, respectively. Pervaporation restricts removal of water from the reaction mixture thus requiring significantly less energy for product recovery when compared to gas stripping.     

Cellulosic Butanol (ABE) Biofuel Production from Sweet Sorghum Bagasse (SSB): Impact of Hot Water Pretreatment and Solid Loadings on Fermentation Employing <Emphasis Type="Italic">Clostridium beijerinckii</Emphasis> P260

A novel butanol fermentation process was developed in which sweet sorghum bagasse (SSB) was pretreated using liquid hot water (LHW) pretreatment technique followed by enzymatic hydrolysis and butanol (acetone butanol ethanol (ABE)) fermentation. A pretreatment temperature of 200 °C resulted in the generation of a hydrolyzate that inhibited butanol fermentation. When SSB pretreatment temperature was decreased to 190 °C (0-min holding time), the hydrolyzate was successfully fermented without inhibition and an ABE productivity of 0.51 g L^?1 h^?1 was achieved which is comparable to the 0.49 g L^?1 h^?1 observed in the control fermentation where glucose was used as a feedstock. These results are based on the use of 86 g L^?1 SSB solid loadings in the pretreatment reactors. We were also able to increase SSB solid loadings from 120 to 200 g L^?1 in the pretreatment step (190 °C) followed by hydrolysis and butanol fermentation. As pretreatment solid loadings increased, ABE yield remained in the range of 0.38–0.46. In these studies, a maximum ABE concentration of 16.88 g L^?1 was achieved. Using the LHW pretreatment technique, 88.40–96.00 % of polymeric sugars (cellulose + hemicellulose) were released in the SSB hydrolyzate. The LHW pretreatment technique does not require chemical additions and is environmentally friendly, and the hydrolyzate can be used successfully for butanol fermentation.     

Engineering rTCA pathway and C4-dicarboxylate transporter for <Emphasis Type="SmallCaps">l</Emphasis>-malic acid production

l-Malic acid is an important component of a vast array of food additives, antioxidants, disincrustants, pharmaceuticals, and cosmetics. Here, we presented a pathway optimization strategy and a transporter modification approach to reconstruct the l-malic acid biosynthesis pathway and transport system, respectively. First, pyruvate carboxylase (pyc) and malate dehydrogenase (mdh) from Aspergillus flavus and Rhizopus oryzae were combinatorially overexpressed to construct the reductive tricarboxylic acid (rTCA) pathway for l-malic acid biosynthesis. Second, the l-malic acid transporter (Spmae) from Schizosaccharomyces pombe was engineered by removing the ubiquitination motification to enhance the l-malic acid efflux system. Finally, the l-malic acid pathway was optimized by controlling gene expression levels, and the final l-malic acid concentration, yield, and productivity were up to 30.25 g L^?1, 0.30 g g^?1, and 0.32 g L^?1 h^?1 in the resulting strain W4209 with CaCO₃ as a neutralizing agent, respectively. In addition, these corresponding parameters of pyruvic acid remained at 30.75 g L^?1, 0.31 g g^?1, and 0.32 g L^?1 h^?1, respectively. The metabolic engineering strategy used here will be useful for efficient production of l-malic acid and other chemicals.     

Semi-industrial scale (30 m<Superscript>3</Superscript>) fed-batch fermentation for the production of <Emphasis Type="SmallCaps">d</Emphasis>-lactate by <Emphasis Type="Italic">Escherichia coli</Emphasis> strain HBUT-D15

d(?)-lactic acid is needed for manufacturing of stereo-complex poly-lactic acid polymer. Large scale d-lactic acid fermentation, however, has yet to be demonstrated. A genetically engineered Escherichia coli strain, HBUT-D, was adaptively evolved in a 15% calcium lactate medium for improved lactate tolerance. The resulting strain, HBUT-D15, was tested at a lab scale (7 L) by fed-batch fermentation with up to 200 g L^?1 of glucose, producing 184–191 g L^?1 of d-lactic acid, with a volumetric productivity of 4.38 g L^?1 h^?1, a yield of 92%, and an optical purity of 99.9%. The HBUT-D15 was then evaluated at a semi-industrial scale (30 m³) via fed-batch fermentation with up to 160 g L^?1 of glucose, producing 146–150 g L^?1 of d-lactic acid, with a volumetric productivity of 3.95–4.29 g L^?1 h^?1, a yield of 91–94%, and an optical purity of 99.8%. These results are comparable to that of current industrial scale l(+)-lactic acid fermentation.     

Improving the production yield and productivity of 1,3-dihydroxyacetone from glycerol fermentation using <Emphasis Type="Italic">Gluconobacter oxydans</Emphasis> NL71 in a compressed oxygen supply-sealed and stirred tank reactor (COS-SSTR)

In this study, a compressed oxygen gas supply was connected to a sealed aerated stirred tank reactor (COS-SSTR) bio-system, leading to a high-oxygen pressure bioreactor used to improve the bio-transformative performance in the production of 1,3-dihydroxyacetone (DHA) from glycerol using Gluconobacter oxydans NL71. A concentration of 301.2 ± 8.2 g L^?1 DHA was obtained from glycerol after 32 h of fed-batch fermentation in the COS-SSTR system. The volumetric productivity for this process was 9.41 ± 0.23 g L^?1 h^?1, which is presently the highest obtained level of glycerol bioconversion into DHA. These results show that the application of this bioreactor would enable microbial production of DHA from glycerol at the industrial scale.     

Improvement of 5-aminolevulinic acid production by Rubrivivax benzoatilyticus PS-5 with self-flocculation by co-fermentation of precursors and volatile fatty acids under pH-controlled conditions

Photosynthetic bacteria are known to utilize volatile fatty acids as a carbon source for growth and product formation. In this study, a new isolate, Rubrivivax benzoatilyticus PS-5, possessing self-flocculation properties, was cultivated in modified glutamate-malate (GM) medium containing glutamate and malate as carbon sources. The effect of acetic acid, propionic acid and butyric acid (at 1–4 g L^?1) as co-substrates and 7.5 mM glycine, 10 mM succinic acid as precursors for 5-aminolevulinic acid (ALA) production from R. benzoatilyticus PS-5 was investigated. Among the volatile fatty acids tested, acetic acid was preferred to butyric acid and propionic acid, with the optimum concentrations of 3 g L^?1, 1 g L^?1 and 3 g L^?1, respectively. The highest ALA production was 169.71 μM, 162.16 μM and 46.18 μM, respectively, while the highest productivity was 2.57 μM h^?1, 2.25 μM h^?1 and 0.96 μM h^?1, respectively. The precursor was consumed completely (100 %) while the assimilation of the acetic acid and butyric acid was 62.50 % and 48.65 %, respectively. Supplementation of propionic acid (at 1–4 g l^?1) had a negative effect on growth and ALA production. To increase production efficiency, the pH-control strategy (at pH 6.0–8.0) during fermentation was tested. The optimum pH was 7.0, giving the maximum ALA production of 286.18 μM and a productivity of 3.97 μM h^?1. These values were 1.68-fold and 1.54-fold higher, respectively, than those under uncontrolled pH conditions.