Sugarcane bagasse enzymatic hydrolysis: rheological data as criteria for impeller selection

The aim of this work was to select an efficient impeller to be used in a stirred reactor for the enzymatic hydrolysis of sugar cane bagasse. All experiments utilized 100 g (dry weight)/l of steam-pretreated bagasse, which is utilized in Brazil for cattle feed. The process was studied with respect to the rheological behavior of the biomass hydrolysate and the enzymatic conversion of the bagasse polysaccharides. These parameters were applied to model the power required for an impeller to operate at pilot scale (100 l) using empirical correlations according to Nagata [16]. Hydrolysis experiments were carried out using a blend of cellulases, β-glucosidase, and xylanases produced in our laboratory by Trichoderma reesei RUT C30 and Aspergillus awamori. Hydrolyses were performed with an enzyme load of 10 FPU/g (dry weight) of bagasse over 36 h with periodic sampling for the measurement of viscosity and the concentration of glucose and reducing sugars. The mixture presented pseudoplastic behavior. This rheological model allowed for a performance comparison to be made between flat-blade disk (Rushton turbine) and pitched-blade (45°) impellers. The simulation showed that the pitched blade consumed tenfold less energy than the flat-blade disk turbine. The resulting sugar syrups contained 22 g/l of glucose, which corresponded to 45% cellulose conversion.     

Enhanced enzymatic hydrolysis of sugarcane bagasse by N-methylmorpholine-N-oxide pretreatment

The cellulose dissolution solvent used in Lyocell process for cellulose fiber preparation, N-methylmorpholine-N-oxide (NMMO) monohydrate, was demonstrated to be an effective agent for sugarcane bagasse pretreatment. Bagasse of 20wt% was readily dissolved in NMMO monohydrate at 130 degrees C within 1h. After dissolution, bagasse could be regenerated by rapid precipitation with water as a porous and amorphous mixture of its original components. The regenerated bagasse exhibited a significant enhancement on enzymatic hydrolysis kinetic. Not only the reducing sugars releasing rate but also hydrolysis yield was enhanced at least twofold as compared with that of untreated bagasse. The cellulose fraction of regenerated bagasse was nearly hydrolyzed to glucose after 72h hydrolysis with Cellulase AP3. The recycled NMMO demonstrated the same performance as the fresh one on bagasse pretreatment for hydrolysis enhancement. The regenerated bagasse was directly used in simultaneous saccharification and fermentation (SSF) for ethanol production by Zymomonas mobilis. No negative effect on ethanol fermentation was observed and ethanol yield approximately 0.15 g ethanol/g baggasse was achieved.     

Extraction and characterization of wax from sugarcane bagasse and the enzymatic hydrolysis of dewaxed sugarcane bagasse

Extraction of high-value products from agricultural wastes is an important component for sustainable bioeconomy development. In this study, wax extraction from sugarcane bagasse was performed and the beneficial effect of dewaxing pretreatment on the enzymatic hydrolysis was investigated. About 1.2% (w/w) of crude sugarcane wax was obtained from the sugarcane bagasse using the mixture of petroleum ether and ethanol (mass ratio of 1:1) as the extraction agent. Results of Fourier-transform infrared characterization and gas chromatography–mass spectrometry qualitative analysis showed that the crude sugarcane wax consisted of fatty fractions (fatty acids, fatty aldehydes, hydrocarbons, and esters) and small amount of lignin derivatives. In addition, the effect of dewaxing pretreatment on the enzymatic hydrolysis of sugarcane bagasse was also investigated. The digestibilities of cellulose and xylan in dewaxed sugarcane bagasse were 18.7 and 10.3%, respectively, compared with those of 13.1 and 8.9% obtained from native sugarcane bagasse. The dewaxed sugarcane bagasse became more accessible to enzyme due to the disruption of the outermost layer of the waxy materials.     

Combination of dilute acid and ionic liquid pretreatments of sugarcane bagasse for glucose by enzymatic hydrolysis

Loss of hemicellulose and inability to effectively decrystallize cellulose, result in low yield and high cost of sugars derived from biomass. In this work, dilute sulfuric acid pretreatment could easily remove most of hemicellulose as sugars. The sugars were successfully used for 2,3-butanediol production with relative high yield (36.1%). Then, the remained solid residue after acid-pretreatment was further pretreated by ionic liquid (IL) to decrease its crystallinity for subsequent enzymatic saccharification. The combination of dilute acid- and IL-pretreatments resulted in significant higher glucose yield (95.5%) in enzymatic saccharification, which was more effective than using dilute acid- or IL-pretreatment alone. This strategy seems a promising route to achieve high yield of sugars from both hemicellulose and cellulose for biorefinery.     

Comparing impacts of physicochemical properties and hydrolytic inhibitors on enzymatic hydrolysis of sugarcane bagasse

An autohydrolysis pretreatment with different conditions was applied to sugarcane bagasse to compare the impacts of the physicochemical properties and hydrolytic inhibitors on its enzymatic hydrolysis. The results indicate that the autohydrolysis conditions significantly affected the physicochemical properties and inhibitors, which further affected the enzymatic hydrolysis. The inhibitor amount, pore size, and crystallinity degree increased with increasing autohydrolysis severity. Furthermore, the enzymatic hydrolysis was enhanced with increasing severity owing to the removal of hemicellulose and lignin. The physicochemical obstruction impeded the enzymatic hydrolysis more than the inhibitors. The multivariate correlated component regression analysis enabled an evaluation of the correlations between the physicochemical properties (and inhibitors) and enzymatic hydrolysis for the first time. According to the results, an autohydrolysis with a severity of 4.01 is an ideal pretreatment for sugarcane bagasse for sugar production.

     

Utilization of sugarcane bagasse for bioethanol production: sono-assisted acid hydrolysis approach

In this study, the production of sugar monomers from sugarcane bagasse (SCB) by sono-assisted acid hydrolysis was performed. The SCB was subjected to sono-assisted alkaline pretreatment. The cellulose and hemicellulose recovery observed in the solid content was 99% and 78.95%, respectively and lignin removal observed during the pretreatment was about 75.44%. The solid content obtained was subjected to sono-assisted acid hydrolysis. Under optimized conditions, the maximum hexose and pentose yield observed was 69.06% and 81.35% of theoretical yield, respectively. The hydrolysate obtained was found to contain very less inhibitors, which improved the bioethanol production and the ethanol yield observed was 0.17 g/g of pretreated SCB.     

Study of kinetic parameters in a mechanistic model for enzymatic hydrolysis of sugarcane bagasse subjected to different pretreatments

The goal of this work is to evaluate the influence of different pretreatments in the kinetics of enzymatic hydrolysis of sugarcane bagasse and to propose a reliable methodology to easily perform sensitivity analysis and updating kinetic parameters whenever necessary. A kinetic model was modified to represent the experimental data of the batch enzymatic hydrolysis of sugarcane bagasse pretreated with alkaline hydrogen peroxide. The simultaneous estimation of kinetic parameters of the mathematical model was performed using the Pikaia genetic algorithm using batch hydrolysis experimental data obtained with different enzymatic loads. Subsequently, Plackett–Burman designs were used to identify the kinetic parameters with the higher influence on the dynamic behavior of the process variables, which were re-estimated to describe experimental data of the hydrolysis of bagasse pretreated with phosphoric acid + sodium hydroxide. The methodology was accurate and straightforward and can be used whenever there are changes in pretreatment conditions and/or fluctuations in biomass composition in different harvests.     

Alkaline-sulfite pretreatment and use of surfactants during enzymatic hydrolysis to enhance ethanol production from sugarcane bagasse

Sugarcane bagasse is a by-product from the sugar and ethanol industry which contains approximately 70 % of its dry mass composed by polysaccharides. To convert these polysaccharides into fuel ethanol it is necessary a pretreatment step to increase the enzymatic digestibility of the recalcitrant raw material. In this work, sugarcane bagasse was pretreated by an alkaline-sulfite chemithermomechanical process for increasing its enzymatic digestibility. Na₂SO₃ and NaOH ratios were fixed at 2:1, and three increasing chemical loads, varying from 4 to 8 % m/m Na₂SO₃, were used to prepare the pretreated materials. The increase in the alkaline-sulfite load decreased the lignin content in the pretreated material up to 35.5 % at the highest chemical load. The pretreated samples presented enhanced glucose yields during enzymatic hydrolysis as a function of the pretreatment severity. The maximum glucose yield (64 %) was observed for the samples pretreated with the highest chemical load. The use of 2.5 g l^?1 Tween 20 in the hydrolysis step further increased the glucose yield to 75 %. Semi-simultaneous hydrolysis and fermentation of the pretreated materials indicated that the ethanol yield was also enhanced as a function of the pretreatment severity. The maximum ethanol yield was 56 ± 2 % for the sample pretreated with the highest chemical load. For the sample pretreated with the lowest chemical load (2 % m/m NaOH and 4 % m/m Na₂SO₃), adding Tween 20 during the hydrolysis process increased the ethanol yield from 25 ± 3 to 39.5 ± 1 %.     

Pretreatment of sugarcane bagasse using supercritical carbon dioxide combined with ultrasound to improve the enzymatic hydrolysis

This work evaluates the pretreatment of sugarcane bagasse combining supercritical carbon dioxide (SC-CO₂) and ultrasound to enhance the enzymatic hydrolysis of pretreated bagasse. In a first step the influence of process variables on the SC-CO₂ pretreatment to enhance the enzymatic hydrolysis was evaluated by mean of a Plackett–Burmann design. Then, the sequential treatment combining ultrasound + SC-CO₂ was evaluated. Results show that treatment using SC-CO₂ increased the amount of fermentable sugar obtained of about 280% compared with the non-treated bagasse, leading to a hydrolysis efficiency (based on the amount of cellulose) as high as 74.2%. Combining ultrasound + SC-CO₂ treatment increased about 16% the amount of fermentable sugar obtained by enzymatic hydrolysis in comparison with the treatment using only ultrasound. From the results presented in this work it can be concluded that the combined ultrasound + SC-CO₂ treatment is an efficient and promising alternative to carry out the pretreatment of lignocellulosic feedstock at relatively low temperatures without the use of hazardous solvents.     

Comparative hydrolysis and fermentation of sugarcane and agave bagasse

Sugarcane and agave bagasse samples were hydrolyzed with either mineral acids (HCl), commercial glucanases or a combined treatment consisting of alkaline delignification followed by enzymatic hydrolysis. Acid hydrolysis of sugar cane bagasse yielded a higher level of reducing sugars (37.21% for depithed bagasse and 35.37% for pith bagasse), when compared to metzal or metzontete (agave pinecone and leaves, 5.02% and 9.91%, respectively). An optimized enzyme formulation was used to process sugar cane bagasse, which contained Celluclast, Novozyme and Viscozyme L. From alkaline–enzymatic hydrolysis of sugarcane bagasse samples, a reduced level of reducing sugar yield was obtained (11–20%) compared to agave bagasse (12–58%). Selected hydrolyzates were fermented with a non-recombinant strain of Saccharomyces cerevisiae. Maximum alcohol yield by fermentation (32.6%) was obtained from the hydrolyzate of sugarcane depithed bagasse. Hydrolyzed agave waste residues provide an increased glucose decreased xylose product useful for biotechnological conversion.     

Hydrothermal processing and enzymatic hydrolysis of sorghum bagasse for fermentable carbohydrates production

Untreated and hydrothermally treated sorghum bagasse (SB) was hydrolyzed to simple sugars by the synergistic action of cellulases and hemicellulases produced by the fungi Fusarium oxysporum and Neurospora crassa. Synergism between the two lignocellulolytic systems was maximized with the application of higher fraction of N. crassa enzymes.Hydrothermolysis of SB was studied at a wide range of treatment times and temperatures. At intense pretreatment conditions (210 °C for 20 min; logR₀ = 4.54), the residual hemicellulose percentage was 17.45%, while formation of inhibitory products, 5-hydromethyl-furfural (HMF), furfural, acetic and formic acid, (0.21, 0.51, 3.36 and 1.80 g/l, respectively) remained in acceptable levels.Maximum conversion of cellulose and total polysaccharides of the untreated SB were 23.18% and 18.79%, respectively. Combining hydrothermal treatment and enzymatic hydrolysis of released oligosaccharides and insoluble solids resulted in improvement of cellulose (approximately 15% increase) and total polysaccharides (two fold) hydrolysis compared to that of untreated SB.     

Xylan extraction from pretreated sugarcane bagasse using alkaline and enzymatic approaches

Background

New biorefinery concepts are necessary to drive industrial use of lignocellulose biomass components. Xylan recovery before enzymatic hydrolysis of the glucan component is a way to add value to the hemicellulose fraction, which can be used in papermaking, pharmaceutical, and food industries. Hemicellulose removal can also facilitate subsequent cellulolytic glucan hydrolysis.

Results

Sugarcane bagasse was pretreated with an alkaline-sulfite chemithermomechanical process to facilitate subsequent extraction of xylan by enzymatic or alkaline procedures. Alkaline extraction methods yielded 53% (w/w) xylan recovery. The enzymatic approach provided a limited yield of 22% (w/w) but produced the xylan with the lowest contamination with lignin and glucan components. All extracted xylans presented arabinosyl side groups and absence of acetylation. 2D-NMR data suggested the presence of O-methyl-glucuronic acid and p-coumarates only in enzymatically extracted xylan. Xylans isolated using the enzymatic approach resulted in products with molecular weights (Mw) lower than 6 kDa. Higher Mw values were detected in the alkali-isolated xylans. Alkaline extraction of xylan provided a glucan-enriched solid readily hydrolysable with low cellulase loads, generating hydrolysates with a high glucose/xylose ratio.

Conclusions

Hemicellulose removal before enzymatic hydrolysis of the cellulosic fraction proved to be an efficient manner to add value to sugarcane bagasse biorefining. Xylans with varied yield, purity, and structure can be obtained according to the extraction method. Enzymatic extraction procedures produce high-purity xylans at low yield, whereas alkaline extraction methods provided higher xylan yields with more lignin and glucan contamination. When xylan extraction is performed with alkaline methods, the residual glucan-enriched solid seems suitable for glucose production employing low cellulase loadings.

     

Effect of alkaline pre-treatment on enzyme synergy for efficient hemicellulose hydrolysis in sugarcane bagasse

This aim of this study was to investigate the effect of ammonium hydroxide (NH₄OH) and sodium hydroxide (NaOH) pre-treatment on the digestibility of sugarcane bagasse (SCB) by hemicellulase action. It was found that pre-treatment of SCB with NH₄OH removed a larger percentage of the SCB lignin and effectively increased SCB digestibility 13.13 fold. The greatest amount of reducing sugar (1194.88 μmol/min) and largest degree of synergy (2.85) was obtained using a combination of two enzymes (25% ManA and 75% XynA) with NH₄OH pre-treated SCB. In this study, NH₄OH therefore appeared to be a more effective pre-treatment step for subsequent hydrolysis by hemicellulases.     

Optimization of sugar release from sweet sorghum bagasse following solvation of cellulose and enzymatic hydrolysis using response surface methodology

To release sugars effectively from sweet sorghum bagasse (SSB), a cellulose solvent and organic solvent‐based lignocellulose fractionation pretreatment approach was studied using response surface methodology (RSM). Based on RSM's central composite design, a batch experimental matrix was set up to determine the effects of reaction time (20–60 min) and temperature (40–60 °C) on delignification, total reducing sugar yield, glucan digestibility, and overall glucose yields following a pretreatment‐hydrolysis process. The optimum pretreatment conditions of 50 °C and 40 min led to 51.4% delignification, 86% overall glucose yield, and 61% overall xylose yield. An effort has also been made to obtain predictive models to illustrate the correlation between independent and dependent variables using RSM. The significance of the correlations and adequacy of these models were statistically tested for the selected objective functions. The optimum pretreatment condition predicted by the model was 49.1 °C and 39.2 min which matched the experimental data well. Results from this study can be applied to large scale biorefineries using sugars released from SSB for producing various biofuels. © 2013 American Institute of Chemical Engineers Biotechnol. Prog., 30:367–375, 2014     

Enzymatic hydrolysis of sugarcane bagasse and straw mixtures pretreated with diluted acid

Abstract

In Brazil, sugarcane biomass is generated in large amounts. Sugarcane bagasse and straw are considered as an important feedstock for renewable energy and biorefinery. This paper aims to study the generation of monosaccharides (C5 and C6) from sugarcane biomass via processing bagasse or straw and mixtures of both materials (bagasse:straw 3:1, 1:1 and 1:3). Samples were pretreated with sulfuric acid which resulted in approximately 90% of hemicellulose solubilization, corresponding to around 58 g L^{? 1} of xylose. Pretreated straw showed greater susceptibility to enzymatic hydrolysis in comparison to bagasse, as shown by glucose yields of 76% and 65%, respectively, whereas the mixtures showed intermediate yields. Thus, one strategy to balance sugarcane biomass availability and possibly increasing 2G ethanol production would be to use bagasse–straw mixtures in appropriate ratios according to market fluctuations. Untreated and pretreated samples were analyzed using X-ray diffraction, but there was no relationship to enzymatic hydrolysis.     

Ultrasonic pretreatment and acid hydrolysis of sugarcane bagasse for succinic acid production using Actinobacillus succinogenes

Immense interest has been devoted to the production of bulk chemicals from lignocellulose biomass. Diluted sulfuric acid treatment is currently one of the main pretreatment methods. However, the low total sugar concentration obtained via such pretreatment limits industrial fermentation systems that use lignocellulosic hydrolysate. Sugarcane bagasse hemicellulose hydrolysate is used as the carbon and nitrogen sources to achieve a green and economical production of succinic acid in this study. Sugarcane bagasse was ultrasonically pretreated for 40 min, with 43.9 g/L total sugar obtained after dilute acid hydrolysis. The total sugar concentration increased by 29.5 %. In a 3-L fermentor, using 30 g/L non-detoxified total sugar as the carbon source, succinic acid production increased to 23.7 g/L with a succinic acid yield of 79.0 % and a productivity of 0.99 g/L/h, and 60 % yeast extract in the medium could be reduced. Compared with the detoxified sugar preparation method, succinic acid production and yield were improved by 20.9 and 20.2 %, respectively.     

Process design for enzymatic adipyl-7-ADCA hydrolysis

Adipyl-7-ADCA is a new source for 7-aminodeacetoxycephalosporanic acid (7-ADCA), one of the substrates for antibiotics synthesis. In this paper, a novel process for enzymatic 7-ADCA production is presented. The process consists of a reactor, a crystallization step, a membrane separation step, and various recycle loops. The reactor can either be operated batch-wise or continuously; with both types of processing high yields can be obtained. For batch reactors chemical degradation of 7-ADCA can be neglected. For continuous reactors, chemical stability of 7-ADCA is a factor to be taken into account. However, it was shown that the reaction conditions and reactor configuration could be chosen in such a way that also for continuous operation chemical degradation is not important. Downstream processing consisted of crystallization of 7-ADCA at low pH, followed by a nanofiltration step with which, at low pH, adipic acid could be separated from adipyl-7-ADCA and 7-ADCA. The separation mechanism of the nanofilter is based on size exclusion combined with charge effects. Application of this filtration step opens possibilities for recycling components to various stages of the process. Adipic acid can be recycled to the fermentation stage of the process while both adipyl-7-ADCA and 7-ADCA can be returned to the hydrolysis reactor. In this way, losses of substrates and product can be minimized.     

Chemical and morphological characterization of sugarcane bagasse submitted to a delignification process for enhanced enzymatic digestibility

Background

While advantages of biofuel have been widely reported, studies also highlight the challenges in large scale production of biofuel. Cost of ethanol and process energy use in cellulosic ethanol plants are dependent on technologies used for conversion of feedstock. Process modeling can aid in identifying techno-economic bottlenecks in a production process. A comprehensive techno-economic analysis was performed for conversion of cellulosic feedstock to ethanol using some of the common pretreatment technologies: dilute acid, dilute alkali, hot water and steam explosion. Detailed process models incorporating feedstock handling, pretreatment, simultaneous saccharification and co-fermentation, ethanol recovery and downstream processing were developed using SuperPro Designer. Tall Fescue (Festuca arundinacea Schreb) was used as a model feedstock.

Results

Projected ethanol yields were 252.62, 255.80, 255.27 and 230.23 L/dry metric ton biomass for conversion process using dilute acid, dilute alkali, hot water and steam explosion pretreatment technologies respectively. Price of feedstock and cellulose enzymes were assumed as $50/metric ton and 0.517/kg broth (10% protein in broth, 600 FPU/g protein) respectively. Capital cost of ethanol plants processing 250,000 metric tons of feedstock/year was $1.92, $1.73, $1.72 and $1.70/L ethanol for process using dilute acid, dilute alkali, hot water and steam explosion pretreatment respectively. Ethanol production cost of $0.83, $0.88, $0.81 and $0.85/L ethanol was estimated for production process using dilute acid, dilute alkali, hot water and steam explosion pretreatment respectively. Water use in the production process using dilute acid, dilute alkali, hot water and steam explosion pretreatment was estimated 5.96, 6.07, 5.84 and 4.36 kg/L ethanol respectively.

Conclusions

Ethanol price and energy use were highly dependent on process conditions used in the ethanol production plant. Potential for significant ethanol cost reductions exist in increasing pentose fermentation efficiency and reducing biomass and enzyme costs. The results demonstrated the importance of addressing the tradeoffs in capital costs, pretreatment and downstream processing technologies.