Effect of different acclimation methods on the performance of microbial fuel cells using phenol as substrate

Single-chamber microbial fuel cells (MFCs) with air-cathode were constructed. MFCs were fed different feedstocks during their inoculation, their role on phenol degradation and MFC performance were investigated. The results showed that the MFC inoculated using glucose exhibited the highest power density (31.3 mW m^?2) when phenol was used as the sole substrate for MFC. The corresponding biodegradation kinetic constant was obtained at 0.035 h^?1, at an initial phenol concentration of 600 mg L^?1. Moreover, the phenol degradation rates in this MFC with closed circuit were 9.8–16.5 % higher than those in MFC with opened circuit. The cyclic voltammograms revealed a different electrochemical activity of the anode biofilms in the MFC, and this led to differences in performance of the MFCs with phenol as sole substrate. These results demonstrated that phenol degradation and power production are affected by current generation and type of acclimation.     

Establishing a core microbiome in acetate-fed microbial fuel cells

Establishing a core microbiome is the first step in understanding and subsequently optimizing microbial interactions in anodic biofilms of microbial fuel cells (MFCs) for increased power, efficiency, and decreased start-up times. In the present study, we used 454 pyrosequencing to demonstrate that a core anodic community would consistently emerge over a period of 4 years given similar conditions. The development and variation across reactor designs of these communities was also explored. The core members present in all high-power generating biofilms were Geobacter, Aminiphilus, Sedimentibacter, Acetoanaerobium, and Spirochaeta, accounting for 72?±?9 % of all genera. Aminiphilus spp., member of the Synergistetes phylum was present at higher abundances than previously reported in any other ecological studies. Results suggest a stable core microbiome in acetate-fed MFCs on both phylogenetic and functional levels.     

Differential biofilms characteristics of Shewanella decolorationis microbial fuel cells under open and closed circuit conditions

Biofilms formation capacities of Shewanella species in microbial fuel cells (MFCs) and their roles in current generation have been documented to be species-dependent. Understandings of the biofilms growth and metabolism are essential to optimize the current generation of MFCs. Shewanella decolorationis S12 was used in both closed-circuit and open-circuit MFCs in this study. The anodic S. decolorationis S12 biofilms could generate fivefold more current than the planktonic cells, playing a dominant role in current generation. Anodic biofilms viability was sustained at 98 ± 1.2% in closed-circuit while biofilms viability in open-circuit decreased to 72 ± 7% within 96 h. The unviable domain in open-circuit MFCs biofilms majorly located at the inner layer of biofilm. The decreased biofilms viability in open-circuit MFCs could be recovered by switching into closed-circuit, indicating that the current-generating anode in MFCs could serve as a favorable electron acceptor and provide sufficient energy to support cell growth and metabolism inside biofilms.     

Layer-by-layer construction of graphene-based microbial fuel cell for improved power generation and methyl orange removal

Development of highly efficient anode is critical for enhancing the power output of microbial fuel cells (MFCs). The aim of this work is to investigate whether modification of carbon paper (CP) anode with graphene (GR) via layer-by-layer assembly technique is an effective approach to promote the electricity generation and methyl orange removal in MFCs. Using cyclic voltammetry and electrochemical impedance spectroscopy, the GR/CP electrode exhibited better electrochemical behavior. Scanning electron microscopy results revealed that the surface roughness of GR/CP increased, which was favorable for more bacteria to attach to the anode surface. The MFCs equipped with GR/CP anode achieved a stable maximum power density of 368 mW m^?2 under 1,000 Ω external resistance and a start time for the initial maximum voltage of 180 h, which were, respectively, 51 % higher and 31 % shorter than the corresponding values of the MFCs with blank anode. The anode and cathode polarization curves revealed negligible difference in cathode potentials but obviously difference in anode potentials, indicating that the GR-modified anode other than the cathode was responsible for the performance improvement of MFC. Meanwhile, compared with MFCs with blank anode, 11 % higher decolorization efficiency and 16 % higher the chemical oxygen demand removal rate were achieved in MFC with GR-modified anode during electricity generation. This study might provide an effective way to modify the anode for enhanced electricity generation and efficient removal of azo dye in MFCs.     

Domestic wastewater treatment using multi-electrode continuous flow MFCs with a separator electrode assembly design

Treatment of domestic wastewater using microbial fuel cells (MFCs) will require reactors with multiple electrodes, but this presents unique challenges under continuous flow conditions due to large changes in the chemical oxygen demand (COD) concentration within the reactor. Domestic wastewater treatment was examined using a single-chamber MFC (130 mL) with multiple graphite fiber brush anodes wired together and a single air cathode (cathode specific area of 27 m²/m³). In fed-batch operation, where the COD concentration was spatially uniform in the reactor but changed over time, the maximum current density was 148?±?8 mA/m² (1,000 Ω), the maximum power density was 120 mW/m², and the overall COD removal was >90 %. However, in continuous flow operation (8 h hydraulic retention time, HRT), there was a 57 % change in the COD concentration across the reactor (influent versus effluent) and the current density was only 20?±?13 mA/m². Two approaches were used to increase performance under continuous flow conditions. First, the anodes were separately wired to the cathode, which increased the current density to 55?±?15 mA/m². Second, two MFCs were hydraulically connected in series (each with half the original HRT) to avoid large changes in COD among the anodes in the same reactor. The second approach improved current density to 73?±?13 mA/m². These results show that current generation from wastewaters in MFCs with multiple anodes, under continuous flow conditions, can be improved using multiple reactors in series, as this minimizes changes in COD in each reactor.     

Enhancing substrate utilization and power production of a microbial fuel cell with nitrogen-doped carbon aerogel as cathode catalyst

Objectives

Catalytic efficiency of a nitrogen-doped, mesoporous carbon aerogel cathode catalyst was investigated in a two-chambered microbial fuel cell (MFC) applying graphite felt as base material for cathode and anode, utilizing peptone as carbon source.

Results

This mesoporous carbon aerogel containing catalyst layer on the cathode increased the maximum power density normalized to the anode volume to 2.7 times higher compared to the maximum power density obtained applying graphite felt cathode without the catalyst layer. At high (2 and 3) cathode/anode volume ratios, maximum power density exceeded 40 W m^?3. At the same time, current density and specific substrate utilization rate increased by 58% resulting in 31.9 A m^?3 and 18.8 g COD m^?3 h^?1, respectively (normalized to anode volume). Besides the increase of the power and the rate of biodegradation, the investigated catalyst decreased the internal resistance from the range of 450–600 to 350–370 Ω.

Conclusions

Although Pt/C catalyst proved to be more efficient, a considerable decrease in the material costs might be achieved by substituting it with nitrogen-doped carbon aerogel in MFCs. Such cathode still displays enhanced catalytic effect.

     

Comparing terracotta and earthenware for multiple functionalities in microbial fuel cells

The properties of earthenware and terracotta were investigated in terms of structural integrity and ion conductivity, in two microbial fuel cell (MFC) designs. Parameters such as wall thickness (4, 8, 18 mm), porosity and cathode hydration were analysed. During the early stages of operation (2 weeks), the more porous earthenware lost anolyte quickly and was unstable between feeding compared to terracotta. Three weeks later MFCs of all thicknesses were more stable and could sustain longer periods of power production without maintenance. In all cases, the denser terracotta produced higher open circuit voltage; however, earthenware the more porous and less iron-rich of the two, proved to be the better material for power production, to the extent that the thickest wall (18 mm) MFC produced 15 % higher power than the thinnest wall (4 mm) terracotta. After 6 weeks of operation, the influence of wall thickness was less exaggerated and power output was comparable between the 4 and 8 mm ceramic membranes. Cylindrical earthenware MFCs produced significantly higher current (75 %) and power (33 %) than terracotta MFCs. A continuous dripping mode of cathode hydration produced threefold higher power than when MFCs were submerged in water, perhaps because of a short-circuiting effect through the material. This shows a significant improvement in terms of biosystems engineering, since a previously high-maintenance half-cell, is now shown to be virtually self-sufficient.     

Stable operation of microbial fuel cells at low temperatures (5–10 °C) with light exposure and its anodic microbial analysis

Performances of microbial fuel cells (MFCs) were studied at 5–10 and 25–30 °C. Results showed stable operation of the MFCs at low temperatures with only slight reductions of voltage and power generation (11 versus 14 % for double-chamber MFC, while 14 versus 21 % for single-chamber MFC, 1,000 Ω) compared to those at mesophilic temperatures. MFCs operated at low temperatures showed lower COD removal rates accompanied by higher coulombic efficiencies (CEs). PCR-DGGE analysis revealed that psychrotrophic microbes (mainly Arcobacter, Pseudomonas, and Geobacter) dominated on anodes of the MFCs at low temperatures. Interestingly, light-induced red substances appeared on anode of the MFCs operated at low temperature and were proven to be the main anodic microbes (Arcobacter and Pseudomonas). Co-existence of the aforementioned microbes could assist stable low-temperature operation of the MFCs. Cyclic voltammetry analysis supported the results of the CE and DGGE. Stable performance of MFCs at low temperatures might be achieved by the control of anodic bacteria.     

Electrocatalytic activity of anodic biofilm responses to pH changes in microbial fuel cells

This study investigates the effects of anodic pH on electricity generation in microbial fuel cells (MFCs) and the intrinsic reasons behind them. In a two-chamber MFC, the maximum power density is 1170 ± 58 mW m⁻² at pH 9.0, which is 29% and 89% higher than those working at pH 7.0 and 5.0, respectively. Electrochemical measurements reveal that pH affects the electron transfer kinetics of anodic biofilms. The apparent electron transfer rate constant (k_app) and exchange current density (i₀) are greater whereas the charge transfer resistance (R_ct) is smaller at pH 9.0 than at other conditions. Scanning electron microscopy verifies that alkaline conditions benefit biofilm formation in MFCs. These results demonstrate that electrochemical interactions between bacteria and electrodes in MFCs are greatly enhanced under alkaline conditions, which can be one of the important reasons for the improved MFC output.     

Increased power generation from primary sludge by a submersible microbial fuel cell and optimum operational conditions

Microbial fuel cells (MFCs) have received attention as a promising renewable energy technology for waste treatment and energy recovery. We tested a submersible MFC with an innovative design capable of generating a stable voltage of 0.250 ± 0.008 V (with a fixed 470 Ω resistor) directly from primary sludge. In a polarization test, the maximum power density was 0.18 W/m² at a current density of 0.8 A/m² with an external resistor of 300 Ω. The anodic solution of the primary sludge needs to be adjusted to a pH 7 for high power generation. The modified primary sludge with an added phosphate buffer prolonged the current generation and increased the power density by 7 and 1.5 times, respectively, in comparison with raw primary sludge. These findings suggest that energy recovery from primary sludge can be maximized using an advanced MFC system with optimum conditions.     

Coupling microbial fuel cells with a membrane photobioreactor for wastewater treatment and bioenergy production

Microbial fuel cells (MFCs) and membrane photobioreactors are two emerging technologies for simultaneous wastewater treatment and bioenergy production. In this study, those two technologies were coupled to form an integrated treatment system, whose performance was examined under different operating conditions. The coupled system could achieve 92–97 % removal of soluble chemical oxygen demand (SCOD) and nearly 100 % removal of ammonia. Extending the hydraulic retention time (HRT) of the membrane photobioreactor to 3.0 days improved the production of algal biomass from 44.4 ± 23.8 to 133.7 ± 12.9 mg L^?1 (based on the volume of the treated water). When the MFCs were operated in a loop mode, their effluent (which was the influent to the algal reactor) contained nitrate and had a high pH, leading to the decreased algal production in the membrane photobioreactor. Energy analysis showed that the energy consumption was mainly due to the recirculation of the anolyte and the catholyte in the MFCs and that decreasing the recirculation rates could significantly reduce energy consumption. The energy production was dominated by indirect electricity generation from algal biomass. The highest energy production of 0.205 kWh m^?3 was obtained with the highest algal biomass production, resulting in a theoretically positive energy balance of 0.033 kWh m^?3. Those results have demonstrated that the coupled system could be an alternative approach for energy-efficient wastewater treatment and using wastewater effluent for algal production.     

A Comparative Study of the Non-acidic Chemically Mediated Antifoulant Properties of Three Sympatric Species of Ascidians Associated with Seagrass Habitats

In this study, the mechanical properties of biofilms formed at the surface of nano-filtration (NF) membranes from a drinking water plant were analysed. Confocal laser scanning microscopy observations revealed that the NF biofilms formed a dense and heterogeneous structure at the membrane surface, with a mean thickness of 32.5 ± 17.7 μm. The biofilms were scraped from the membrane surface and analysed in rotation and oscillation experiments with a RheoStress 150 rotating disk rheometer. During rotation analyses, a viscosity decrease with speed of shearing characteristic of rheofluidification was observed (η = 300 Pa s for ý = 0.3 s^?1). In the oscillation analyses with a sweeping of frequency (1–100 Hz), elasticity (G′) ranged from 3000 to 3500 Pa and viscosity (G″) from 800 to 1200 Pa. Creep curves obtained with an application of a shear stress of 30 Pa were viscoelastic in nature. The G ₀ and η values were, respectively, 1.4 ± 0.3 × 10³ Pa and 3.3 ± 0.65 × 10⁶ Pa s. The relationship between the characteristics of NF biofilms and the flow conditions encountered during NF is discussed.     

Increased power generation from primary sludge in microbial fuel cells coupled with prefermentation

Raw primary sludge and the prefermentation liquor (PL) of primary sludge were used to generate electricity in single-chambered air-cathode microbial fuel cells (MFCs). The MFCs treating the primary sludge produced 0.53 V and 370 mW/m² for the maximum potential and power density, respectively. In the primary sludge-fed MFCs, only 5 % of the total energy production was produced from direct electricity generation, whereas 95 % of that resulted from the conversion of methane to electricity. MFCs treating the PL generated the maximum potential of 0.58 V and maximum power density of 885 mW/m², respectively. In the energy production analysis, direct electricity production (1,921 Wh/kg TCOD_rem) in the MFCs treating the PL was much higher than that of the primary sludge-fed MFC (138 Wh/kg TCOD_rem). Volatile suspended solids during 10 days were reduced to 18.3 and 38 % in the primary sludge-fed MFCs and prefermentation reactor, respectively. These findings suggest that a two-stage process including prefermentation and MFCs is of great benefit on sludge reduction and higher electricity generation from primary sludge.     

Power generation from cassava alcohol wastewater: effects of pretreatment and anode aeration

Cassava alcohol wastewater produced from the bioethanol production industry is carbohydrate-rich wastewater with large quantities of insoluble organic compounds. Microbial fuel cells (MFCs) were used for electricity recovery and pollutants removal from this wastewater. Different pretreatment methods (solid–liquid separation, ultrasonication, pre-fermentation) and anode-aeration modes were explored in MFCs aimed to enhance the efficiency of power generation and pollutants removal. Pre-fermentation was found to be the most effective pretreatment method. A maximum power density of 437.13 ± 15.6 mW/m² and TCOD removal of 62.5 ± 3.5 % were achieved using the pre-fermented wastewater, 150 and 20 % higher than the un-pretreated control. Aeration in anode chamber could promote the hydrolysis of organic matter and production of VFAs in the raw wastewater, and increase TCOD removal and power density. Pre-fermentation coupled with halfway anode aeration may be a feasible strategy to enhance power generation and pollutants removal from the cassava wastewater in MFCs.     

Biodegradation and proton exchange using natural rubber in microbial fuel cells

Microbial fuel cells (MFCs) generate electricity from waste but to date the technology’s development and scale-up has been held-up by the need to incorporate expensive materials. A costly but vital component is the ion exchange membrane (IEM) which conducts protons between the anode and cathode electrodes. The current study compares natural rubber as an alternative material to two commercially available IEMs. Initially, the material proved impermeable to protons, but gradually a working voltage was generated that improved with time. After 6 months, MFCs with natural rubber membrane outperformed those with anion exchange membrane (AEM) but cation exchange membrane (CEM) produced 109 % higher power and 16 % higher current. After 11 months, polarisation experiments showed a decline in performance for both commercially available membranes while natural rubber continued to improve and generated 12 % higher power and 54 % higher current than CEM MFC. Scanning electron microscope images revealed distinct structural changes and the formation of micropores in natural latex samples that had been employed as IEM for 9 months. It is proposed that the channels and micropores formed as a result of biodegradation were providing pathways for proton transfer, reflected by the steady increase in power generation over time. These improvements may also be aided by the establishment of biofilms that, in contrast, caused declining performance in the CEM. The research demonstrates for the first time that the biodegradation of a ubiquitous waste material operating as IEM can benefit MFC performance while also improving the reactor’s lifetime compared to commercially available membranes.     

Enhancing electrical outputs of the fuel cells with Geobacter sulferreducens by overexpressing nanowire proteins

Protein nanowires are critical electroactive components for electron transfer of Geobacter sulfurreducens biofilm. To determine the applicability of the nanowire proteins in improving bioelectricity production, their genes including pilA, omcZ, omcS and omcT were overexpressed in G. sulfurreducens. The voltage outputs of the constructed strains were higher than that of the control strain with the empty vector (0.470–0.578 vs. 0.355 V) in microbial fuel cells (MFCs). As a result, the power density of the constructed strains (i.e. 1.39–1.58 W m⁻²) also increased by 2.62- to 2.97-fold as compared to that of the control strain. Overexpression of nanowire proteins also improved biofilm formation on electrodes with increased protein amount and thickness of biofilms. The normalized power outputs of the constructed strains were 0.18–0.20 W g⁻¹ that increased by 74% to 93% from that of the control strain. Bioelectrochemical analyses further revealed that the biofilms and MFCs with the constructed strains had stronger electroactivity and smaller internal resistance, respectively. Collectively, these results demonstrate for the first time that overexpression of nanowire proteins increases the biomass and electroactivity of anode-attached microbial biofilms. Moreover, this study provides a new way for enhancing the electrical outputs of MFCs.     

Factors affecting current production in microbial fuel cells using different industrial wastewaters

This study evaluated how different types of industrial wastewaters (bakery, brewery, paper and dairy) affect the performance of identical microbial fuel cells (MFCs); and the microbial composition and electrochemistry of MFC anodes. MFCs fed with paper wastewater produced the highest current density (125 ± 2 mA/m²) at least five times higher than dairy (25 ± 1 mA/m²), brewery and bakery wastewaters (10 ± 1 mA/m²). Such high current production was independent of substrate degradability. A comprehensive study was conducted to determine the factor driving current production when using the paper effluent. The microbial composition of anodic biofilms differed according to the type of wastewater used, and only MFC anodes fed with paper wastewater showed redox activity at −134 ± 5 mV vs NHE. Electrochemical analysis of this redox activity indicated that anodic bacteria produced a putative electron shuttling compound that increased the electron transfer rate through diffusion, and as a result the overall MFC performance.     

Improving the power generation of microbial fuel cells by modifying the anode with single-wall carbon nanohorns

Objectives

To increase the power generation of microbial fuel cells (MFCs), anode modification with carbon materials (activated carbon, carbon nanotubes, and carbon nanohorns) was investigated.

Results

Maximum power densities of a stainless-steel anode MFC with a non-modified electrode (SS-MFC), an activated carbon-modified electrode (AC-MFC), a carbon nanotube-modified electrode (CNT-MFC) and a carbon nanohorn-modified electrode (CNH-MFC) were 72, 244, 261 and 327 mW m^?2, respectively. The total polarization resistance measured by electrochemical impedance spectroscopy were 3610 Ω for SS-MFC, 283 Ω for AC-MFC, 231 Ω for CNTs-MFC, and 136 Ω for CNHs-MFC, consistent with the anode resistances obtained by fitting the anode polarization curves.

Conclusions

Single-wall carbon nanohorns are better than activated carbon and carbon nanotubes as a new anode modification material for improving anode performance.

     

Thermal mitigation of Pseudomonas aeruginosa biofilms

Bacterial biofilms infect 2–4% of medical devices upon implantation, resulting in multiple surgeries and increased recovery time due to the very great increase in antibiotic resistance in the biofilm phenotype. This work investigates the feasibility of thermal mitigation of biofilms at physiologically accessible temperatures. Pseudomonas aeruginosa biofilms were cultured to high bacterial density (1.7?×?10⁹ CFU cm^?2) and subjected to thermal shocks ranging from 50°C to 80°C for durations of 1–30 min. The decrease in viable bacteria was closely correlated with an Arrhenius temperature dependence and Weibull-style time dependence, demonstrating up to six orders of magnitude reduction in bacterial load. The bacterial load for films with more conventional initial bacterial densities dropped below quantifiable levels, indicating thermal mitigation as a viable approach to biofilm control.     

Open circuit versus closed circuit enrichment of anodic biofilms in MFC: effect on performance and anodic communities

The influence of various carbon anodes; graphite, sponge, paper, cloth, felt, fiber, foam and reticulated vitreous carbon (RVC); on microbial fuel cell (MFC) performance is reported. The feed was brewery wastewater diluted in domestic wastewater. Biofilms were grown at open circuit or under an external load. Microbial diversity was analysed as a function of current and anode material. The bacterial community formed at open circuit was influenced by the anode material. However at closed circuit its role in determining the bacterial consortia formed was less important than the passage of current. The rate and extent of organic matter removal were similar for all materials: over 95% under closed circuit. The biofilm in MFCs working at open circuit and in the control reactors, increased COD removal by up to a factor of nine compared with that for baseline reactors. The average voltage output was 0.6 V at closed circuit, with an external resistor of 300 kΩ and 0.75 V at open circuit for all materials except RVC. The poor performance of this material might be related to the surface area available and concentration polarizations caused by the morphology of the material and the structure of the biofilm. Peak power varied from 1.3 mW m^?2 for RVC to 568 mW m^?2 for graphite with biofilm grown at closed circuit.