Evaluating skeletal muscle electromechanical delay with intramuscular pressure

IntroductionIntramuscular pressure (IMP) is the fluid pressure generated within skeletal muscle and directly reflects individual muscle tension. The purpose of this study was to assess the development of force, IMP, and electromyography (EMG) in the tibialis anterior (TA) muscle during ramped isometric contractions and evaluate electromechanical delay (EMD).MethodsForce, EMG, and IMP were simultaneously measured during ramped isometric contractions in eight young, healthy human subjects. The EMD between the onset of force and EMG activity (Δt-EMG force) and the onset of IMP and EMG activity (Δt EMG-IMP) were calculated.ResultsA statistically significant difference (p < 0.05) was found between the mean force-EMG EMD (36 ± 31 ms) and the mean IMP-EMG EMD (3 ± 21 ms).ConclusionsIMP reflects changes in muscle tension due to the contractile muscle elements.     

EMG signal amplitude normalization technique in stretch-shortening cycle movements

Analysis of functional movements using surface electromyography (EMG) often involves recording both eccentric and concentric muscle activity during a stretch-shorten cycle (SSC). The techniques used for amplitude normalization are varied and are independent of the type of muscle activity involved. The purpose of this study was: (i) to determine the effect of 11 amplitude normalization techniques on the coefficient of variation (CV) during the eccentric and concentric phases of the SSC; and (ii) to establish the effect of the normalization techniques on the EMG signal under variable load and velocity. The EMG signal of the biceps brachii of eight normal subjects was recorded under four SSC conditions and three levels of isometric contraction. The 11 derived normalization values were total rms, mean rms and peak rms (100 ms time constant) for the isometric contractions and the mean rms and peak rms values of the ensemble values for each set of isotonic contractions. Normalization using maximal voluntary isometric contractions (MVIC), irrespective of rms processing (total, mean or peak), demonstrated greater CV above the raw data for both muscle actions. Mean ensemble values and submaximal isometric recordings reduced the CV of concentric data. No amplitude normalization technique reduced the CV for eccentric data under loaded conditions. An ANOVA demonstrated significant (P < 0.01) main effects for load and velocity on concentric raw data and an interaction (P < 0.05) for raw eccentric data. No significant effects were demonstrated for changes in velocity when the data were normalized using mean rms values. The reduction of the CV should not be at the expense of true biological variance and current normalization techniques poorly serve the analysis of eccentric muscle activity during the SSC.     

Mechanomyography and electromyography force relationships during concentric, isometric and eccentric contractions.

The purpose of this study was to investigate systematically if complementary knowledge could be obtained from the recordings of electromyography (EMG) and mechanomyography (MMG) signals. EMG and MMG activities were recorded from the first dorsal interosseous muscle during slow concentric, isometric, and eccentric contraction at 0, 25, 50, 75 and 100% of the maximal voluntary contraction (MVC). The combination of the EMG and MMG recordings during voluntary concentric-isometric-eccentric contraction showed significant different non-linear EMG/force and MMG/force relationships (P<0.001). The EMG root mean square (rms) values increased significantly from 0 to 50% MVC during concentric and isometric contraction and up to 75% MVC during eccentric contraction (P<0.05). The MMG rms values increased significantly from 0 to 50% MVC during concentric contraction (P<0.05). The non-linear relationships depended mainly on the type and the level of contraction together with the angular velocity. Furthermore, the type of contraction, the contraction level, and the angular velocity influenced the electromechanical efficiency evaluated as the MMG to EMG ratio (P<0.05). These results highlight that EMG and MMG provide complementary information about the electrical and mechanical activity of the muscle. Different activation strategies seem to be used during graded isometric and anisometric contraction.     

Isometric squat force output and muscle activity in stable and unstable conditions

The purpose of this study was to assess the effect of stable vs. unstable conditions on force output and muscle activity during an isometric squat. Nine men involved in recreational resistance training participated in the investigation by completing a single testing session. Within this session subjects performed isometric squats either while standing directly on the force plate (stable condition, S) or while standing on inflatable balls placed on top of the force plate (unstable condition, U). Electromyography (EMG) was recorded during both conditions from the vastus lateralis (VL), vastus medialis (VM), biceps femoris (BF), and medial gastrocnemius (G) muscles. Results indicated peak force (PF) and rate of force development (RFD) were significantly lower, 45.6% and 40.5% respectively, in the U vs. S condition (p < or = 0.05). Average integrated EMG values for the VL and VM were significantly higher in the S vs. U condition. VL and VM muscle activity was 37.3% and 34.4% less in U in comparison to S. No significant differences were observed in muscle activity of the BF or G between U and S. The primary finding in this investigation is that isometric squatting in an unstable condition significantly reduces peak force, rate of force development, and agonist muscle activity with no change in antagonist or synergist muscle activity. In terms of providing a stimulus for strength gain no discernable benefit of performing a resistance exercise in an unstable condition was observed in the current study.     

Human isometric force production and electromyogram activity of knee extensor muscles in water and on dry land

This study was designed to determine trial-to-trial and day-to-day reproducibility of isometric force and electromyogram activity (EMG) of the knee extensor muscles in water and on dry land as well as to make comparisons between the two training conditions in muscle activity and force production. A group of 20 healthy subjects (12 women and 8 men) were tested three times over 2 weeks. A measurement session consisted of recordings of maximal and submaximal isometric knee extension force with simultaneous recording of surface EMG from the vastus medialis, vastus lateralis and biceps femoris muscles. To ensure identical measurement conditions the same patient elevator chair was used in both the dry and the wet environment. Intraclass correlation coefficients (ICC) and coefficients of variation (CV) showed high trial-to-trial (ICC = 0.95-0.99, CV = 3.5%-11%) and day-to-day reproducibility (ICC=0.85-0.98, CV=11%-19%) for underwater and dry land measurements of force and EMG in each muscle during maximal contractions. The day-to-day reproducibility for submaximal contractions was similar. The interesting finding was that underwater EMG amplitude decreased significantly in each muscle during maximal (P < 0.01-P < 0.001) and submaximal contractions (P < 0.05-P < 0.001). However, the isometric force measurements showed similar values in both wet and dry conditions. The water had no disturbing effect on the electrodes as shown by slightly lowered interelectrode resistance values, the absence of artefacts and low noise levels of the EMG signals. It was concluded that underwater force and EMG measurements are highly reproducible. The significant decrease of underwater EMG could have electromechanical and/or neurophysiological explanations.     

Comparison of electromyographic activity during eccentrically versus concentrically loaded isometric contractions

Electromyographic (EMG) amplitude and mechanical tension are directly related during isometric contraction. Maximal voluntary isometric contractions are typically elicited through two different procedures; resisting a load, which is eccentric in nature, and contracting against an immovable object, which is concentric in nature. A wealth of literature exists indicating that EMG amplitude during concentric contractions is greater than that of eccentric contractions of the same magnitude. However, the effects of different methods to elicit isometric contraction on EMG amplitude have yet to be investigated. The purpose of this study was to compare EMG amplitudes under different loading configurations designed to elicit isometric muscle contraction. Twenty healthy volunteers (10 males and 10 females, age = 23 ± 2 yrs, height = 1.7 ± 0.09 m, mass = 69.9 + 16.8 kg) performed a maximal voluntary plantarflexion effort for which the vertical ground reaction force (GRFv) sampled from a force plate and surface EMG of the soleus were recorded. Participants then performed isometric plantarflexion at 20%, 30%, 40%, and 50% GRFv_max in a seated position, from a neutral ankle position, under two different counterbalanced isometric loading conditions (concentric and eccentric). For concentric loading conditions, the subject contracted against an immovable resistance to the specified %GRFv identified via visual and auditory feedback. For eccentric loading conditions, subjects contracted against an applied load placed on the distal anterior thigh that produced the specified %GRFv. This applied load had the tendency to force the ankle into dorsiflexion. Therefore, plantarflexion force, in an attempt to maintain the ankle in a neutral position, resisted lengthening of the plantarflexor musculature, thus representing eccentric loading during an isometric contraction. Mean EMG amplitude was compared across loading levels and types using a 2 (loading type: concentric, eccentric) × 4 (loading level: 20%, 30%, 40%, 50% GRFv) repeated-measures ANOVA. The main effect for loading level was significant (p = 0.007). However, the main effect for loading type, and the loading type × loading level interaction were non-significant (p > 0.05). The present findings provide evidence that isometric muscle contractions loaded in either concentric or eccentric manners elicit similar EMG amplitudes, and are therefore comparable in research settings.     

Recovery of the human biceps electromyogram after heavy eccentric, concentric or isometric exercise.

Five men performed submaximal isometric, concentric or eccentric contractions until exhaustion with the left arm elbow flexors at respectively 50%, 40% and 40% of the prefatigued maximal voluntary contraction force (MVC). Subsequently, and at regular intervals, the surface electromyogram (EMG) during 30-s isometric test contractions at 40% of the prefatigued MVC and the muscle performance parameters (MVC and the endurance time of an isometric endurance test at 40% prefatigued MVC) were recorded. Large differences in the surface EMG response were found after isometric or concentric exercise on the one hand and eccentric exercise on the other. Eccentric exercise evoked in two of the three EMG parameters [the EMG amplitude (root mean square) and the rate of shift of the EMG mean power frequency (MPF)] the greatest (P less than 0.001) and longest lasting (up to 7 days) response. The EMG response after isometric or concentric exercise was smaller and of shorter duration (1-2 days). The third EMG parameter, the initial MPF, had already returned to its prefatigued value at the time of the first measurement, 0.75 h after exercise. The responses of EMG amplitude and of rate of MPF shift were similar to the responses observed in the muscle performance parameters (MVC and the endurance time). Complaints of muscle soreness were most frequent and severe after the eccentric contractions. Thus, eccentric exercise evoked the greatest and longest lasting response both in the surface EMG signal and in the muscle performance parameters.     

Change in the Ipsilateral Motor Cortex Excitability Is Independent from a Muscle Contraction Phase during Unilateral Repetitive Isometric Contractions

The aim of this study was to investigate the difference in a muscle contraction phase dependence between ipsilateral (ipsi)- and contralateral (contra)-primary motor cortex (M1) excitability during repetitive isometric contractions of unilateral index finger abduction using a transcranial magnetic stimulation (TMS) technique. Ten healthy right-handed subjects participated in this study. We instructed them to perform repetitive isometric contractions of the left index finger abduction following auditory cues at 1 Hz. The force outputs were set at 10, 30, and 50% of maximal voluntary contraction (MVC). Motor evoked potentials (MEP) were obtained from the right and left first dorsal interosseous muscles (FDI). To examine the muscle contraction phase dependence, TMS of ipsi-M1 or contra-M1 was triggered at eight different intervals (0, 20, 40, 60, 80, 100, 300, or 500 ms) after electromyogram (EMG) onset when each interval had reached the setup triggering level. Furthermore, to demonstrate the relationships between the integrated EMG (iEMG) in the active left FDI and the ipsi-M1 excitability, we assessed the correlation between the iEMG in the left FDI for the 100 ms preceding TMS onset and the MEP amplitude in the resting/active FDI for each force output condition. Although contra-M1 excitability was significantly changed after the EMG onset that depends on the muscle contraction phase, the modulation of ipsi-M1 excitability did not differ in response to any muscle contraction phase at the 10% of MVC condition. Also, we found that contra-M1 excitability was significantly correlated with iEMG in all force output conditions, but ipsi-M1 excitability was not at force output levels of below 30% of MVC. Consequently, the modulation of ipsi-M1 excitability was independent from the contraction phase of unilateral repetitive isometric contractions at least low force output.     

Maintenance of EMG activity and loss of force output with instability

Swiss Balls used as a platform for training provide an unstable environment for force production. The objective of this study was to measure differences in force output and electromyographic (EMG) activity of the pectoralis major, anterior deltoid, triceps, latissimus dorsi, and rectus abdominus for isometric and dynamic contractions under stable and unstable conditions. Ten healthy male subjects performed a chest press while supported on a bench or a ball. Unstable isometric maximum force output was 59.6% less than under stable conditions. However, there were no significant differences in overall EMG activity between the stable and unstable protocols. Greater EMG activity was detected with concentric vs. eccentric or isometric contractions. The decreased balance associated with resistance training on an unstable surface may force limb musculature to play a greater role in joint stability. The diminished force output suggests that the overload stresses required for strength training necessitate the inclusion of resistance training on stable surfaces.     

Experimental muscle pain increases mechanomyographic signal activity during sub-maximal isometric contractions.

This study was designed to investigate the local effect of experimental muscle pain on the MMG and the surface EMG during a range of sub-maximal isometric contractions. Muscle pain was induced by injections of hypertonic saline into the biceps brachii muscle in 12 subjects. Injections of isotonic saline served as a control. Pain intensity and location, MMG and surface EMG from the biceps brachii were assessed during static isometric (0%, 10%, 30%, 50% and, 70% of the maximal voluntary contraction) and ramp isometric (0-50% of the maximal voluntary contraction) elbow flexions. MMG and surface EMG signals were analyzed in the time and frequency domain. Experimentally induced muscle pain induced an increase in root mean square values of the MMG signal while no changes were observed in the surface EMG. Most likely this increase reflects changes in the mechanical contractile properties of the muscle and indicates compensatory mechanisms, i.e. decreased firing rate and increased twitch force to maintain a constant force output in presence of experimental muscle pain. Under well-controlled conditions, MMG recordings may be more sensitive than surface EMG recordings and clinically useful for detecting non-invasively increased muscle mechanical contributions during muscle pain conditions.     

Effects of fatigue on the temporal neuromuscular control of vastus medialis muscle in humans

The effects of muscle fatigue on the temporal neuromuscular control of the vastus medialis (VM) muscle were investigated in 19 young male subjects. The electromyogram (EMG) activities of VM and the force generation capacities of the quadriceps muscle were monitored before and after a fatigue protocol. In response to light signals, which were triggered randomly, the subjects made three maximal isometric knee extensions. This was then followed by the fatigue protocol which consisted of 30 isometric maximal voluntary contractions at a sequence of 5-s on and 5-s off. Immediately after the exercise to fatigue, the subjects performed another three maximal isometric contractions in response to the light signals. The effects of fatigue on the temporal neuromuscular control were then investigated by dividing the total reaction time (TRT) into premotor time (PMT) and electromechanical delay (EMD). The TRT was defined as the time interval between the light signal and the onset of the knee extension force. The PMT was defined as the time from the light signal to the onset of EMG activities of VM, and EMD as the time interval between onset of EMG activities to that of force generation. Following the contractions to fatigue there was a significant decrease in peak force (Fpeak, P = 0.016), an increase in the root mean square (rms)-EMG: Fpeak quotient (P = 0.001) but an insignificant change in the median frequency (P = 0.062) and rms-EMG (P = 0.119). Significant lengthening of mean EMD was found after the fatigue protocol [0.0396 (SD 0.009) vs. 0.0518 (SD 0.016) s P<0.001]. The lengthening of EMD in VM would affect the stabilizing effect of the patella during knee extension. The faster mean PMT [0.2445 (SD 0.093) vs. 0.2075 (SD 0.074) s, P = 0.042] following the fatigue protocol might have compensated for the lengthened EMD and contributed to the insignificant change in the mean TRT [0.284 (SD 0.09) vs. 0.259 (SD 0.073) s, P = 0.164]. This was probably related to the low level of fatigue (15% decrease in force) and the stereotyped nature of the action such that the effects of the fatigue on neuromuscular control were likely to have been attributable to peripheral processes.     

Effects of repetitive dynamic contractions upon electromechanical delay

The effect of repeated maximal effort isotonic contractions on electromechanical delay was studied. Over 4 days, 17 male subjects performed 400 rapid elbow flexion trials. The kinematics and surface electromyographic (EMG) activity of the biceps brachii of these subjects were recorded. The period from the onset of the EMG until the beginning of movement was defined as the electromechanical delay. The period from the beginning of movement until the end of the EMG was defined as the second component of the contraction. Over the 4 day period there was an increase in the speed of limb movement. The mean power frequency and the duration of the EMG during the electromechanical delay did not change, while the root-mean-square amplitude increased. The duration of the EMG during the second component of the contraction remained stable. The mean power frequency and the root-mean-square amplitude of the EMG during the second component of the contraction increased with the speed of limb movement. We conclude that the faster contractions were a result of changes in motor unit recruitment during the second component of the contraction, rather than in the electromechanical delay.     

Quadriceps femoris electromyogram during concentric, isometric and eccentric phases of fatiguing dynamic knee extensions

The objective of this study was to examine the superficial quadriceps femoris (QF) muscle electromyogram (EMG) during fatiguing knee extensions. Thirty young adults were evaluated for their one-repetition maximum (1RM) during a seated, right-leg, inertial knee extension. All subjects then completed a single set of repeated knee extensions at 50% 1RM, to failure. Subjects performed a knee extension (concentric phase), held the weight with the knee extended for 2s (isometric phase), and lowered the weight in a controlled manner (eccentric phase). Raw EMG of the vastus medialis (VM), vastus lateralis (VL) and rectus femoris (RF) muscles were full-wave rectified, integrated and normalized to the 1RM EMG, for each respective phase and repetition. The EMG median frequency (f(med)) was computed during the isometric phase. An increase in QF muscle EMG was observed during the concentric phase across the exercise duration. VL EMG was greater than the VM and RF muscles during the isometric phase, in which no significant changes occurred in any of the muscles across the exercise duration. A significant decrease in EMG across the exercise duration was observed during the eccentric phase, with the VL EMG greater than the VM and RF muscles. A greater decrease in VL and RF muscle f(med) during the isometric phase, than the VM muscle, was observed with no gender differences. The findings demonstrated differential recruitment of the superficial QF muscle, depending on the contraction mode during dynamic knee extension exercise, where VL muscle dominance appears to manifest across the concentric-isometric-eccentric transition.     

Motor unit activation patterns during isometric, concentric and eccentric actions at different force levels.

Motor unit activation patterns were studied during four different force levels of concentric and eccentric actions. Eight male subjects performed concentric and eccentric forearm flexions with the movement range from 100 degrees to 60 degrees in concentric and from 100 degrees to 140 degrees elbow angle in eccentric actions. The movements were started either from zero preactivation or with isometric preactivation of the force levels of 20, 40, 60 and 80% MVC. The subjects were then instructed to maintain the corresponding relative force levels during the dynamic actions. Intramuscular and surface EMG was recorded from biceps brachii muscle. Altogether 28 motoneuron pools were analyzed using the intramuscular spike-amplitude frequency (ISAF) analysis technique of Moritani et al. The mean spike amplitude was lower and the mean spike frequency higher in the isometric preactivation phase than in the consequent concentric and eccentric actions. When the movements started with isometric preactivation the mean spike amplitude increased significantly (P<0.001) up to 80% in isometric and concentric actions but in eccentric actions the increase continued only up to 60% (P<0.01). The mean spike frequency in isometric preactivation and in concentric action with preactivation was lower only at the 20% force level (P<0.01) as compared to the other force levels while in eccentric action with preactivation the increase between the force levels was significant (P<0.01) up to 60%. When the movement was started without preactivation the mean spike amplitude at 20% and at 40% force level was higher (P<0.01) in eccentric action than in concentric actions. It was concluded that the recruitment threshold may be lower in dynamic as compared to isometric actions. The recruitment of fast motor units may continue to higher force levels in isometric and in concentric as in eccentric actions which, on the other hand, seems to achieve the higher forces by increasing the firing rate of the active units. At the lower force levels mean spike amplitude was higher in eccentric than in concentric actions which might indicate selective activation of fast motor units. This was, however, the case only when the movements were started without isometric preactivation.     

Muscles within muscles: the neuromotor control of intra-muscular segments

The aim of this investigation was to anatomically identify, and then determine the function of, individual segments within the human deltoid muscle. The anatomical structure of the deltoid was determined through dissection and/or observation of the shoulder girdles of 11 male cadavers (aged 65–84 years). These results indicate that the deltoid consists of seven anatomical segments (D1–D7) based upon the distinctive arrangement of each segment's origin and insertion. Radiographic analysis of a cadaveric shoulder joint suggested that only the postero-medial segment D7 has a line of action directed below the shoulder joint's axis of rotation. The functional role of each individual segment was then determined utilising an electromyographic (EMG) technique. Seven miniature (1 mm active plate; 7 mm interelectrode distance) bipolar surface electrodes were positioned over the proximal portion of each segment's muscle belly in 18 male and female subjects (18–30 years). EMG waveforms were then recorded during the production of rapid isometric shoulder abduction and adduction force impulses with the shoulder joint in 40 degrees of abduction in the plane of the scapula. Each subject randomly performed 15 abduction and 15 adduction isometric force impulses following a short familiarisation period. All subjects received visual feed back on the duration and amplitude of each isometric force impulse produced via a visual force-time display which compared subject performance to a criterion force-time curve. Movement time was 400 ms (time-to-peak isometric force) at an intensity level of 50% maximal voluntary contraction. Temporal and intensity analyses of the EMG waveforms, as well as temporal analysis of the isometric force impulses, revealed the neuromotor control strategies utilised by the CNS to control the activity of each muscle segment. The results showed that segmental neuromotor control strategies differ across the breadth of the muscle and that individual segments of the deltoid can be identified as having either “prime mover”, “synergist”, “stabiliser” or “antagonist” functions; functional classifications normally associated with whole muscle function. Therefore, it was concluded that the CNS can “fine tune” the activity of at least six discrete segments within the human deltoid muscle to efficiently meet the demands of the imposed motor task. Accepted: 15 December 1997     

Increased rate of force development and neural drive of human skeletal muscle following resistance training.

The maximal rate of rise in muscle force [rate of force development (RFD)] has important functional consequences as it determines the force that can be generated in the early phase of muscle contraction (0-200 ms). The present study examined the effect of resistance training on contractile RFD and efferent motor outflow ("neural drive") during maximal muscle contraction. Contractile RFD (slope of force-time curve), impulse (time-integrated force), electromyography (EMG) signal amplitude (mean average voltage), and rate of EMG rise (slope of EMG-time curve) were determined (1-kHz sampling rate) during maximal isometric muscle contraction (quadriceps femoris) in 15 male subjects before and after 14 wk of heavy-resistance strength training (38 sessions). Maximal isometric muscle strength [maximal voluntary contraction (MVC)] increased from 291.1 +/- 9.8 to 339.0 +/- 10.2 N. m after training. Contractile RFD determined within time intervals of 30, 50, 100, and 200 ms relative to onset of contraction increased from 1,601 +/- 117 to 2,020 +/- 119 (P < 0.05), 1,802 +/- 121 to 2,201 +/- 106 (P < 0.01), 1,543 +/- 83 to 1,806 +/- 69 (P < 0.01), and 1,141 +/- 45 to 1,363 +/- 44 N. m. s(-1) (P < 0.01), respectively. Corresponding increases were observed in contractile impulse (P < 0.01-0.05). When normalized relative to MVC, contractile RFD increased 15% after training (at zero to one-sixth MVC; P < 0.05). Furthermore, muscle EMG increased (P < 0.01-0.05) 22-143% (mean average voltage) and 41-106% (rate of EMG rise) in the early contraction phase (0-200 ms). In conclusion, increases in explosive muscle strength (contractile RFD and impulse) were observed after heavy-resistance strength training. These findings could be explained by an enhanced neural drive, as evidenced by marked increases in EMG signal amplitude and rate of EMG rise in the early phase of muscle contraction.     

The electro-mechanical delay of the erector spinae muscle: influence of rate of force development, fatigue and electrode location.

Electro-mechanical delay (EMD) values of the erector spinae muscle were obtained using a technique based on the cross-correlation between the force and the electromyogram (EMG). Seven subjects performed a series of 20 submaximal dynamic isometric contractions in a seated position at two frequencies (0.5 Hz and 1 Hz) to study the influence of the rate of force development on EMD. Mean EMD values of 125.7 (SD 28.1) ms (1 Hz) and 136.8 (SD 28.6) ms (0.5 Hz) were shown to differ significantly (P = 0.02). This finding supports the hypothesis that EMD is inversely related to the rate of force development and implies that the time to stretch the series elastic component is an important factor determining EMD. After performing a series of fatiguing contractions EMD did not differ significantly from the control value. Multiple regression analysis showed that maximal voluntary contraction force (MVC) and endurance time of the fatiguing exercise correlated significantly with EMD. The site from which the EMG signal was recorded had no significant influence on EMD. However, the coefficient of correlation between force and the EMG-signal differed significantly between electrode positions. The magnitude of the EMD values found emphasized the need to account for this delay when interpreting temporal patterns of activation of the muscles in, for example, lifting tasks.     

Behaviour of triceps surae muscle-tendon complex in different jump conditions

The force-length relationship of the human muscle-tendon complex (MTC) of the triceps surae and the achilles tendon was investigated in various stretch load conditions. Six male subjects performed various vertical jumps with maximal effort: squat jumps (SJ), counter movement jumps (CMJ) and drop jumps (DJ) from a height of 24 cm, 40 cm and 56 cm. The force-length relationship was calculated from the signals of the components of the ground reaction forces and the kinematic data obtained from the high-speed film records. Surface electromyograms (EMG) of the soleus, gastrocnemius and tibialis anterior muscles were also recorded. The force-length diagrams showed individually high sensitivity to the imposed stretch load. In conditions with relatively low stretch load requirements there was a counter-clockwise direction observable, indicating that the energy absorbed during the eccentric, or lengthening phase was lower than the energy delivered during the concentric, or shortening phase. In high load conditions this relationship was reversed indicating a negative energy balance. The EMG-length diagrams of SJ and CMJ consisted of an initial isometric loading of the muscle, followed by a shortening phase with only slightly reduced EMG amplitudes. In DJ, however, the diagrams showed an initial lengthening of the MTC with fairly constant activation amplitudes. After 40 ms an isometric loading of the muscle, lasting for approximately 80 ms, was followed by a shortening phase. It was concluded that segmental stretch reflex activation represented the predominant activation process during the isometric loading phase, to meet the adequate stiffness properties of the MTC.     

Electromyographic adaptations elicited by submaximal exercise in those naive to and in those adapted to eccentric exercise: a descriptive report

The purpose of this study was to describe an electromyogram (EMG) pattern during a submaximal eccentric task in 7 subjects adapted to high-force chronic eccentric exercise and 6 subjects naive to eccentric exercise. The EMG in all subjects was quantified during identical submaximal (200 W) eccentric and concentric cycle ergometry tasks. The EMG of the eccentrically adapted subjects was decreased (p < 0.05) compared to the eccentrically naive subjects, in duration, amplitude, and intensity as evidenced by a decreased EMG during the pedal cycle. This decrease may be one component of the protective effect that results from progressively increasing repeated bouts of eccentric muscle work. Clients and patients transitioning to rigorous overload training should become adapted to high eccentric loads and forces to avoid injury and a potential delay in their strength and conditioning training regimens.     

The repeated-bout effect: influence on biceps brachii oxygenation and myoelectrical activity

This study investigated biceps brachii oxygenation and myoelectrical activity during and following maximal eccentric exercise to better understand the repeated-bout effect. Ten men performed two bouts of eccentric exercise (ECC1, ECC2), consisting of 10 sets of 6 maximal lengthening contractions of the elbow flexors separated by 4 wk. Tissue oxygenation index minimum amplitude (TOI(min)), mean and maximum total hemoglobin volume by near-infrared spectroscopy, torque, and surface electromyography root mean square (EMG(RMS)) during exercise were compared between ECC1 and ECC2. Changes in maximal voluntary isometric contraction (MVC) torque, range of motion, plasma creatine kinase activity, muscle soreness, TOI(min), and EMG(RMS) during sustained (10-s) and 30-repeated isometric contraction tasks at 30% (same absolute force) and 100% MVC (same relative force) for 4 days postexercise were compared between ECC1 and ECC2. No significant differences between ECC1 and ECC2 were evident for changes in torque, TOI(min), mean total hemoglobin volume, maximum total hemoglobin volume, and EMG(RMS) during exercise. Smaller (P < 0.05) changes and faster recovery of muscle damage markers were evident following ECC2 than ECC1. During 30% MVC tasks, TOI(min) did not change, but EMG(RMS) increased 1-4 days following ECC1 and ECC2. During 100% MVC tasks, EMG(RMS) did not change, but torque and TOI(min) decreased 1-4 days following ECC1 and ECC2. TOI(min) during 100% MVC tasks and EMG(RMS) during 30% MVC tasks recovered faster (P < 0.05) following ECC2 than ECC1. We conclude that the repeated-bout effect cannot be explained by altered muscle activation or metabolic/hemodynamic changes, and the faster recovery in muscle oxygenation and activation was mainly due to faster recovery of force.