Detection of radioactivity on microtiterplates in situ using a photon-counting imager

A position-sensitive single-photon counting imaging system, which can determine intensity and location of a light source, has been used for the detection of 125I-labeled Interleukin-1 and [3H]thymidine in 96 wells of a microtiter plate (MTP) simultaneously. 4 Bq (1 Bq = 1 Bequerel = 1 disintegration/s), 22 and 150 Bq of 125I and 3, 10 and 100 Bq of 3H were visualized and quantified by transforming the radioactivity into light in the visible range by means of Xtalscint, a solid scintillator. After only 1 min of photon accumulation time, the highest radioactivity of both isotopes could be clearly distinguished from background. Photon counts correlate well with radioactivity measured in a beta-counter (for 3H) and a gamma-counter (for 125I). The overall counting efficiency was about 5% for 125I and 3% for 3H.     

Direct counting of tissues containing radioactive cholesterol by a two-phase liquid scintillation method

A rapid and simple method for counting radioactivity in tissue samples containing [³H]- or [¹⁴C]-cholesterol is described.Up to 500 μl of the specimen to be counted (plasma, tissue homogenate) is measured into a counting vial. The lipids of the tissue are extracted into 15 ml of a toluene-based scintillation mixture containing 37.5% ethylene glycol monomethyl ether that is added to the same vial. With the addition of 1 ml water, two phases form: the upper toluene phase containing all cholesterol together with the scintillating phosphor and the lower water phase containing most of the quenching material. Bleaching to reduce color quenching is not necessary. Chemiluminescence is negligible. The counting efficiencies are appreciably higher than those obtained in aqueous one-phase scintillation systems but lower than those obtained with pure standards in one-phase pure toluene scintillation systems.     

Fluorescence quenching of beta-carboline alkaloids in micellar media. A study to select the adequate surfactant to use in analytical techniques.

The study of fluorescence quenching of the fluorophores allows the localization of the alkaloids (harmane and harmine) in the micelles (SDS, CTAB, Brij-35) to be established. In aqueous micellar solutions (SDS and Brij-35) at pH 13.0, emission corresponding to the neutral or zwitterionic forms can be observed. In the presence of CTAB (pH = 13.0) it was possible to observe the emission of anionic form. These species are not present in buffered aqueous solutions at these pH values. Bromide ion was added to the different surfactant solutions and the quenching effect was studied according to the Stern-Volmer equation. In the presence of SDS the quenching effect is considerably reduced compared to the aqueous solutions without surfactants, while for Brij-35 micelles were similar to those observed in homogeneous aqueous solution. For CTAB micelles a notable fluorescence quenching was observed for the different pH values studied. The fluorescence quenching studies show that the neutral species are associated inside the micelles, instead of the ionic species (cationic, zwitterionic or anionic) remaining on the surface of the micelles. The anionic surface of SDS micelles prevents the quenching effect by anionic quenchers for both neutral and charged species.     

Counting emissions from potassium-42 in plant tissue with a liquid scintillation spectrometer

Summary A method has been devised to count emissions from K⁴² in plant tissue by liquid scintillation spectrometer with low quenching. The plant samples were ashed in aluminium dishes, folded into aluminium wafers and suspended in the liquid scintillator of counting vials. The samples were counted in a scintillation spectrometer at one to five minute intervals seven or more times and until the total exceeded 1000 counts. The efficiency of counting was approximately 70%.A computer program was written to calculate decay corrections for the short half-life isotope K⁴². The program computed the weighted mean of the counts, standard deviation of the mean, percentage standard deviation of the mean and Chi-square value for each sample. The measurements were precise enough for K-uptake studies.     

A convenient, efficient, and inexpensive method for scintillation counting of polyacrylamide gel slices after electrophoresis

A method is described for analyzing the radioactivity of ³H-labeled RNA after separation by gel electrophoresis. The gels were soaked in 10% acetic acid and were sliced. The gel slices were dehydrated in alcohol, then saturated with toluene, and finally permeated with a toluene-based scintillation fluid containing butyl-PBD. The radioactivity of RNA was then analyzed in situ in the gel slices using a liquid scintillator. The counting efficiency of this technique is high, about 58%. This is even slightly better than the counting efficiency attained after solubilization of the RNA in Soluene 350 (about 55%). With the same fluor, Permablend III, the counting efficiencies of the two techniques are alike.     

Estimation of monosaccharide radioactivity in biological samples through osazone derivatization

A method for the quantitative estimation of radioactivity in the glucose (monosaccharide) fraction of biological samples is presented. Radioactive samples are added with cold glucose, and 1 aliquot receives a known amount of radioactive glucose as internal standard. After controlled osazone formation and three washings of the yellow precipitate, the osazones are dissolved, decolored, and their radioactivity determined through scintillation counting. The overall efficiency of recovery is 23–24% of the initial radioactivity. Each sample is corrected by the recovery of its own internal standard. There is a very close linear relationship between radioactivity present in the samples and radioactivity found, despite the use of different biological samples (rat plasma, hen egg yolk and albumen).     

Extraction of label during processing of brain tissue for electron microscopic autoradiographic investigation of glycoprotein metabolism

Rats were injected intracerebrally with (3H) fucose and survived for 30 min and 24 h. Following perfusion fixation with aldehydes, Vibratome sections of the brains were processed for embedding in resin and the radioactivity in the various solutions measured by scintillation counting. The decline of radioactivity was monitored in up to 18 successive buffer washes. Whereas 85% of the initial radioactivity could be eluted after 30 min, only 7% were extractable after 24 h survival time. Addition of unlabelled L-fucose to the fixative and buffers caused a small insignificant increase of the total radioactivity extracted. Only small amounts of radioactivity could be removed by treatment with trichloroacetic acid after extensive rinsing in buffer. It is concluded that thorough rinsing in buffer (which is more important with short-time experiments) is effective in removing the acid-soluble radioactivity. An additional safe-guard lies in dehydration by ethanol. The ethanol series also removes acid-soluble radioactivity in addition to small amounts of what is probably higher molecular weight material.     

Enzymatic determination of carbon (14C)-labeled glycerol in biological samples

A method for determination of glycerol-specific-radioactivity in biological samples is presented. It is based on the following steps: (a) enzymatic conversion of glycerol to dihydroxyacetone-phosphate, (b) quantitative trapping of dihydroxyacetone-phosphate in SPE amino (NH₂) columns, (c) eluation with HCl 0.5 N of dihydroxyacetone-phosphate followed by radioactivity counting and (d) estimation of the radioactivity thus trapped compared with that of enzymatically untreated aliquots of the same samples. No interferences from other ¹⁴C-labeled materials tested such as d-glucose, l-alanine, l-glutamine and d-β-hydroxybutyrate were observed. This inexpensive and high-speed method can be applied in routine multiple estimations of glycerol-specific-radioactivity in biological samples in tracer metabolic studies.     

Extraction of label during processing of brain tissue for electron microscopic autoradiographic investigation of glycoprotein metabolism

Summary Rats were injected intracerebrally with (³H) fucose and survived for 30 min and 24 h. Following perfusion fixation with aldehydes, Vibratome sections of the brains were processed for embedding in resin and the radioactivity in the various solutions measured by scintillation counting. The decline of radioactivity was monitored in up to 18 successive buffer washes. Whereas 85% of the initial radioactivity could be eluted after 30 min, only 7% were extractable after 24 h survival time. Addition of unlabelled L-fucose to the fixative and buffers caused a small insignificant increase of the total radioactivity extracted. Only small amounts of radioactivity could be removed by treatment with trichloroacetic acid after extensive rinsing in buffer. It is concluded that thorough rinsing in buffer (which is more important with shorttime experiments) is effective in removing the acid-soluble radioactivity. An additional safe-guard lies in dehydration by ethanol. The ethanol series also removes acid-soluble radioactivity in addition to small amounts of what is probably higher molecular weight material.     

Preparation of 14C-labeled algal samples for liquid scintillation counting

Four commonly used techniques for preparation of ¹⁴C-labeled algal samples on membranes for liquid scintillation counting were compared and a simple technique for apparent net assimilation measurement from aqueous samples was introduced. All four techniques yielded similar radioactivities from the test cultures and are thus suitable for measurements of ¹⁴C algal samples. The possibly carcinogenic solvent dioxane was not necessary with PCS scintillation cocktail for dissolving radioactivity from algae on filters.     

A carbon dioxide collection accessory for the rapid combustion apparatus for preparation of biological samples for liquid scintillation analysis

A carbon dioxide collection accessory is described for the previously reported combustion system for preparation of biological samples for liquid scintillation counting. A sample can be burned and collected every 3 min. Sample size is limited by the capacity of the solvent to absorb carbon dioxide without precipitation. The system can be used for collecting water as well as carbon dioxide, for double isotope counting. The method has a collection recovery of 97%, is calibrated by internal standards, and shows a coefficient of variation of 1.1%.     

High sensitivity mass spectrometric determination of peptides: direct analysis of aqueous solutions

The high sensitivity analysis of peptides by fast atom bombardment mass spectrometry has been achieved using a continuous flow probe for the introduction of samples contained in aqueous solutions. Small aliquots of sample (0.5-1 microliter) are injected into a solvent flow containing water/glycerol (8:2). For several peptide samples tested whose molecular weights were between 1000 and 1500 daltons, molecular ions were selectively monitored at the 20 fmol level with a signal-to-chemical noise of about 4:1, and full scan data were obtained on about 5 pmol of sample. The increase in sensitivity observed using the continuous flow probe is shown to be a consequence of both the decrease in the chemical background noise and to the increase in ion yields obtained from the bombardment of aqueous sample solutions.     

Continuous measurement of lysis of radioactively marked fibrin clots

Methods for continuous measurement of dissolution of experimentally induced radioactively labelled thrombi were described. They are suited for the use in artificial circulating systems and in animal experiments. The radioactivity can be measured continuously in a circulating system by fitting a flow through cell with a well scintillator. In order to measure thrombotic processes in vivo, we developed a specially adapted single hole collimator. By this device changes in radioactivity over a defined occluded area of the vessel could be detected. The usefulness of the methods was demonstrated by means of a thrombolytic agent.     

Enhancing Cycle Stability of Lithium Iron Phosphate in Aqueous Electrolytes by Increasing Electrolyte Molarity

Aqueous lithium ion batteries (ALIBs) exhibit great potential to reduce the cost and improve the safety of rechargeable energy storage technologies. Lithium iron phosphate (LFP) cathodes have become a material of choice for many conventional, high power LIBs. However, experimental studies on LFP in aqueous lithium (Li) ion electrolytes are limited. Here, results of systematic studies are shown where it is demonstrated that the Li salt concentration of the aqueous electrolyte can significantly improve discharge capacity retention while minimally impacting rate capability, for electrodes made with a typical commercial sub‐micron sized LFP powder. Based on the postmortem analysis and the results of electrochemical characterization it is proposed that undesirable side reactions of aqueous electrolytes with LFP induce electrochemical separation of individual particles within the electrode, leading to the observed capacity fading. Increasing the salt concentration in aqueous solutions effectively reduces the concentration of water molecules in the electrolyte, which are mostly responsible for these undesirable side reactions. Similar trends observed with other cathode materials suggest that the use of concentrated aqueous electrolyte solutions offers an effective route to improve stability of aqueous Li ion batteries.     

A novel fluorescent sensor based on electrosynthesized benzene sulfonic acid‐doped polypyrrole for determination of Pb(II) and Cu(II)

To develop conducting organic polymers (COPs) as luminescent sensors for determination of toxic heavy metals, a new benzene sulfonic acid‐doped polypyrrole (PPy‐BSA) thin film was electrochemically prepared by cyclic voltammetry (CV) on flexible indium tin oxide (ITO) electrode in aqueous solution. PPy‐BSA film was characterized by FTIR spectrometry, X‐ray photoelectron spectroscopy (XPS) and scanning electron microscopy (SEM). The optical properties of PPy‐BSA were investigated by ultraviolet (UV)‐visible absorption and fluorescence spectrometry in dimethylsulfoxide (DMSO) diluted solutions. PPy‐BSA fluorescence spectra were strongly quenched upon increasing copper(II) ion (Cu²⁺) and lead(II) ion (Pb²⁺) concentrations in aqueous medium, and linear Stern–Volmer relationships were obtained, which indicated the existence of a main dynamic fluorescence quenching mechanism. BSA‐PPy sensor showed a high sensitivity for detection of both metallic ions, Cu²⁺ and Pb²⁺, with very low limit of detection values of 3.1 and 18.0 nM, respectively. The proposed quenching‐fluorimetric sensor might be applied to the determination of traces of toxic heavy metallic ions in water samples.     

Complete extraction in a form suitable for liquid scintillation counting of tritium-labeled proteins from polyacrylamide gels

Large (200 mm3) slices of polyacrylamide gels crosslinked with N,N'-diallyltartardiamide which contain tritium-labeled protein are readily solubilized in periodic acid for liquid scintillation counting of radioactivity, but the apparent recovery of label never exceeds 82%. Extraction of the slices with two commercial solubilizers at 60 degrees C gave recoveries of 82-90% which were not improved by prolonged incubation. Treatment of the slices at ambient temperature with 1.0 ml of 2% sodium periodate for 30 min followed by the addition of 0.7 ml of aqueous tetrabutylammonium hydroxide (40% w/v) gives solutions which can be immediately counted at 35% efficiency with low background and with 100% recovery of tritiated protein     

Analysis of acylcarnitines as their N-demethylated ester derivatives by gas chromatography-chemical ionization mass spectrometry.

A novel approach to the analysis of acylcarnitines has been developed. It involves a direct esterification using propyl chloroformate in aqueous propanol followed by ion-pair extraction with potassium iodide into chloroform and subsequent on-column N-demethylation of the resulting acylcarnitine propyl ester iodides. The products, acyl N-demethylcarnitine propyl esters, are volatile and are easily analyzed by gas chromatography-chemical ionization mass spectrometry. For medium-chain-length (C4-C12) acylcarnitine standards, detection limits are demonstrated to be well below 1 ng starting material using selected ion monitoring. Well-separated gas chromatographic peaks and structure-specific mass spectra are obtained with samples of synthetic and biological origin. Seven acylcarnitines have been characterized in the urine of a patient suffering from medium-chain acyl-CoA dehydrogenase deficiency.     

Non-penetrating polymeric cryofixatives for ultrastructural and analytical studies of biological tissues.

Existing freezing methods for biological tissues, either for the purposes of storing living material or for ultrastructural observation, are hampered by various limitations, such as small samples (spray-freezing) or the introduction of physiological and/or cytological alterations (incubation in DMSO or glycerol, high pressure freezing). We have investigated the possibility of using aqueous polymer solutions as extracellular cryofixative media, the basis of structural preservation being the capacity of relatively dilute solutions to vitrify under quench cooling conditions. Evidence is presented to show that two such polymers (polyvinylpyrrolidone and hydroxyethyl starch) control—or even inhibit—intracellular freezing in a wide variety of quench cooled tissue samples. The effects of these polymers on the physiology of tissues from a range of different organisms has been assessed by microscopy, electrophysiology and secretion studies. At the concentrations necessary to ensure vitrification the polymer solutions cause only slight perturbations of the normal functioning of the cells studied. The special application of these studies to freeze fracture and scanning electron microscopy is discussed.     

A radioligand assay of tomatine

A novel method for the assay of tomatine in plant extracts is described. It is based on precipitation of tomatine with cholesterols-4-¹⁴C and determination of the radioactivity remaining in solution by scintillation counting. Pigments that cause quenching are removed by chromatography on Sephadex LH20.     

A new rapid method for quantitating radioactive proline, 4-hydroxyproline,and 3-hydroxyproline

A simple and rapid method for separating proline, 4-hydroxyproline and 3-hydroxyproline was developed by the use of high-voltage electrophoresis. An excellent counting efficiency of proline was achieved by a simple extraction of the labeled material from paper; 98–100% recovery of count rates was obtained, equivalent to recoveries from column chromatography. This method can tolerate high concentrations of salt, acid, and protein in the sample. No carrier is required and multiple samples (up to 15) can be separated on a single sheet and analyzed within 2 h. Serial dilution experiments showed excellent linearity. An average recovery rate of 92% was obtained for samples over a wide range of radioactivity and high sensitivity of the method was demonstrated. This analysis is applicable to protein hydrolysates and to determination of the free amino acids in the presence of protein. Thus, proline, 4-hydroxyproline and 3-hydroxyproline can be quantitated simultaneously in any biological sample.