Application of electrochemically prepared polypyrrole-polyvinyl sulphonate films to DNA biosensor

Double stranded calf thymus deoxyribonucleic acid (DNA) was physisorbed onto polypyrrole-polyvinyl sulphonate (PPY-PVS) films electrochemically deposited onto indium-tin-oxide (ITO) coated glass plates. These DNA immobilized PPY-PVS films optimized for various conditions, such as polymerization potential, pH of buffer, DNA concentration and scan rate were characterized using Fourier-transform infrared (FT-IR) spectroscopy, atomic force microscopy (AFM) and cyclic voltammetry (CV) techniques, respectively. The amperometric response studies of these DNA/PPY-PVS electrodes were carried out as a function of 2-aminoantharcene (2-AA, 0.01-20 ppm) and o-chlorophenol (OCP, 0.1-30 ppm) concentration, respectively at 25 degrees C. The observed amperometric current arising due to oxidation of guanine in the DNA/PPY-PVS films decreased linearly with the increase in the concentration of 2-AA and OCP. It has been revealed that 10 ppm of 2-AA is sufficient to reduce the observed guanine oxidation peak current by approximately -95+/-10% as compared to the reported values. A 25 ppm of OCP was capable enough to reduce the guanine oxidation current to zero. These DNA/PPY-PVS electrodes were found to have a shelf life of about 4 months when stored at 25 degrees C.     

One-step electrochemically co-assembled redox-active [Ru(bpy)(2)(tatp)](2+)-BSA-SWCNTs hybrid film for non-redox protein biosensors

A redox-active [Ru(bpy)(2)(tatp)](2+)-BSA-SWCNTs (bpy=2,2'-bipyridine, tatp=1,4,8,9-tetra-aza-triphenylene, BSA=bovine serum albumin, SWCNTs=single-walled carbon nanotubes) hybrid film is fabricated on an indium-tin oxide (ITO) electrode via one-step electrochemical co-assembly approach. BSA is inherently dispersive and therefore served as the linking mediator of SWCNTs, which facilitate the redox reactions of [Ru(bpy)(2)(tatp)](2+) employed as a reporter of BSA. The evidences from differential pulse voltammetry, cyclic voltammetry, scanning electron microscope, emission spectroscopy and fluorescence microscope reveal that the [Ru(bpy)(2)(tatp)](2+)-BSA-SWCNTs hybrid can be electrochemically co-assembled on the ITO electrode, showing two pairs of well-defined Ru(II)-based redox waves. Furthermore, the electrochemical co-assembly of the [Ru(bpy)(2)(tatp)](2+)-BSA-SWCNTs hybrid is found to be strongly dependent on the simultaneous presence of BSA and SWCNTs, indicating a good linear response to BSA in the range from 6 to 50mgL(-1). The results from this study provide an electrochemical co-assembly method for the development of non-redox protein biosensors.     

Enzymatic glucose biosensor based on CeO2 nanorods synthesized by non-isothermal precipitation

Cerium oxide nanorods (CeO(2) NRs) were synthesized without templates through a low cost and simple non-isothermal precipitation method. The structure and morphology of CeO(2) NRs were characterized by X-ray diffraction and transmission electron microscopy. The CeO(2) NRs films, deposited on indium tin oxide (ITO)-coated glass substrates through electrophoretic deposition, were used for the immobilization of glucose oxidase (GOx). Field emission scanning electron microscopy, Fourier transform infrared spectroscopy, cyclic voltammetry, and electrochemical impedance spectroscopy were used to characterize the CeO(2) NRs/ITO and GOx/CeO(2) NRs/ITO electrodes. The GOx/CeO(2) NRs/ITO electrode exhibits a linear range for the detection of glucose from 2 to 26 mM (correlation coefficient: 0.99) at 1-2s response time. Biosensor sensitivity is 0.165 μA mM(-1) cm(-2) with 100 μM detection limit. The anti-interference ability of the biosensor was also examined. The mediator-less application of CeO(2) NRs for glucose sensing was demonstrated.     

Direct electrochemical characterization of Vitreoscilla sp. hemoglobin entrapped in organic films

The redox properties of a prokaryotic, Vitreoscilla sp. hemoglobin (VHb) in fuzzy organic films are studied with electrochemistry. This VHb exhibits irreversible electrochemical response at bare pyrolytic graphite (PG) electrode surfaces. However, upon being entrapped in organic films, the heterogeneous electron transfer rate of VHb will be sufficiently high to produce a quasi-reversible electrochemical response. The observation of electrocatalysis (reduction of O2) by hemes suggests that the protein can retain its biological activity under these conditions.     

Nucleic acid sensor for insecticide detection

Nucleic acid sensor based on polyaniline (PANI) has been fabricated by covalently immobilizing double stranded calf thymus (dsCT) DNA onto perchlorate (ClO(-) (4))-doped PANI film deposited onto indium-tin-oxide (ITO) glass plate using 1-(3-dimethylaminopropyl)-3-ethylcarbodiimide hydrochloride (EDC)/N-hydroxysuccinimide (NHS) chemistry. These dsCT-DNA-PANI-ClO(4)/ITO and PANI-ClO(4)/ITO electrodes have been characterized using square wave voltammetry, electrochemical impedance, scanning electron microscopy (SEM) and Fourier-transform-infrared (FTIR) measurements. This disposable dsCT-DNA-PANI-ClO(4)/ITO bioelectrode, stable for about 4 months, can be used to detect cypermethrin (0.005 ppm) and trichlorfon (0.01 ppm) in 30 and 60 s, respectively.     

Invertase inhibition based electrochemical sensor for the detection of heavy metal ions in aqueous system: Application of ultra-microelectrode to enhance sucrose biosensor's sensitivity

We are reporting fabrication and characterization of electrochemical sucrose biosensor using ultra-microelectrode (UME) for the detection of heavy metal ions (Hg(II), Ag(I), Pb(II) and Cd(II)). The working UME, with 25 microm diameter, was modified with invertase (INV, EC: 3.2.1.26) and glucose oxidase (GOD, EC: 1.1.3.4) entrapped in agarose-guar gum. The hydrophilic character of the agarose-guar gum composite matrix was checked by water contact angle measurement. The atomic force microscopy (AFM) images of the membranes showed proper confinement of both the enzymes during co-immobilization. The dynamic range for sucrose biosensor was achieved in the range of 1 x 10(-10) to 1 x 10(-7)M with lower detection limit 1 x 10(-10)M at pH 5.5 with 9 cycles of reuse. The spectrophotometric and electrochemical studies showed linear relationship between concentration of heavy metal ions and degree of inhibition of invertase. The toxicity sequence for invertase using both methods was observed as Hg(2+)>Pb(2+)>Ag(+)>Cd(2+). The dynamic linear range for mercury using electrochemical biosensor was observed in the range of 5 x 10(-10) to 12.5 x 10(-10)M for sucrose. The lower detection limit for the fabricated biosensor was found to be 5 x 10(-10)M. The reliability of the electrochemical biosensor was conformed by testing the spike samples and the results were comparable with the conventional photometric DNSA method.     

Cholesterol biosensor based on N-(2-aminoethyl)-3-aminopropyl-trimethoxysilane self-assembled monolayer

Cholesterol oxidase (ChOx) has been covalently immobilized onto two-dimensional self-assembled monolayer (SAM) of N-(2-aminoethyl)-3-aminopropyl-trimethoxysilane (AEAPTS) deposited on the indium-tin oxide (ITO) coated glass plates using N-ethyl-N'-(3-dimethylaminopropyl) carbodiimide and N-hydroxysuccinimide (EDC/NHS) chemistry. These ChO x/AEAPTS/ITO bioelectrodes are characterized using contact angle (CA) measurements, UV-visible spectroscopy, atomic force microscopy (AFM), electrochemical impedance technique, and Fourier transform infrared (FT-IR) technique. The covalently immobilized ChOx-modified AEAPTS bioelectrodes are used for the estimation of cholesterol in solution using UV-visible technique. These cholesterol sensing bioelectrodes show linearity as 50 to 500 mg/dl for cholesterol solution, detection limit as 25mg/dl, sensitivity as 4.499 x 10(-5) Abs (mg/dl)(-1), K(m) value as 58.137 mg/dl (1.5mM), apparent enzyme activity as 1.81 x 10(-3) U cm(-2), shelf life of approximately 10 weeks, and electrode reusability as 10 times.     

Monitoring of cell growth and assessment of cytotoxicity using electrochemical impedance spectroscopy

Electrochemical impedance spectroscopy (EIS) was used to monitor the growth of mammalian cancer cells and evaluate the cytotoxicity of chemicals using Fe(CN)6(3-/4-) as a redox probe. Cancer cells, the human hepatocarcinoma cell line (BEL7404), were grown on optically transparent indium tin oxide (ITO) semiconductor slides, which were used as the working electrodes in electrochemical experiments. Attachment and proliferation of cancer cells on ITO surfaces resulted in increase of electron-transfer resistance (R(et)) between the redox probe of Fe(CN)6(3-/4-) in electrolyte solution and ITO electrode surface. For cytotoxicity assessment, cells grown on ITO substrates were further cultured in the presence of different cytotoxicants and electrochemical impedance measurements were carried out at different time intervals. Gemcitabine, a promising antineoplastic drug showing activity against a wide spectrum of human solid tumors, was selected as a model for long-term cytotoxicity effect study, whereas mercury chloride represented a model for acute toxicants. The inhibitions of gemcitabine and mercury chloride on the viability and proliferation of BEL7404 cells were observed from the electrochemical impedance experiments, and the different action modes were discriminated. Additionally, microscope images were also used to observe the effects of these two chemicals on the morphology of the cells. General consistency has been found between the electrochemical impedance response and the morphological observation. Such an impedance method provides a simple and inexpensive way for in vitro assessment of chemical cytotoxicity.     

An electrochemical biosensor for the detection of tyrosine oxidation induced by Fenton reaction

A simple and sensitive electrochemical biosensor was used to detect tyrosine oxidation induced by hydroxyl radicals generated by Fenton reaction (Fe(2+)/H(2)O(2)). Poly(glu, tyr) (4:1) peptides were immobilized on indium tin oxide (ITO) electrode surface via layer-by-layer assembly technique, and Os(bpy)(3)(2+)-mediated tyrosine oxidation current was employed as the signal reporter of the biosensor. It was found that the electrochemical signal of the peptide decreased markedly after incubation with Fenton reagents. Interestingly, L-dopa, the oxidation product of tyrosine, was likely to form complexes with Fe(III), which could suppress the electro-oxidation of L-dopa and resulted in decrease of current response. Our results indicate that the peptide damage involved two steps and was a second-order reaction. X-ray photoelectron spectroscopy was used to quantitatively determine nitrogen elemental percentage on peptide-coated electrode surface, which eliminated the possibility that signal decrease was caused by peptide backbone cleavage. Moreover, the lowest concentration of Fenton reagents that could be detected was 10 μM Fe(2+) or H(2)O(2), similar to the level in vivo. We suggest that the biosensor can be used to detect protein damage induced by Fenton reaction.     

Polypyrrole-hydrogel composites for the construction of clinically important biosensors.

The present study reports on the use of p(2-hydroxyethyl methacrylate) (pHEMA) in which polypyrrole and various oxidoreductase enzymes were physically entrapped to function as a viable matrix for the construction of clinically important amperometric biosensors. Glucose oxidase, cholesterol oxidase and galactose oxidase biosensors were constructed. Electrode-supported hydrogel films were prepared by UV polymerization of the HEMA component (containing the dissolved enzyme) followed immediately by electrochemical polymerization (+0.7V vs. Ag/AgCl) of the pyrrole component within the interstitial spaces of the pre-formed hydrogel network. The optimized glucose oxidase biosensor displayed a wide linear glucose response range (5.0 x 10(-5) to 2.0 x 10(-2) M), a detection limit (3S(y/x)/sensitivity) of 25 microM and a response time of 35-40 s. The analytical recovery of glucose in serum samples ranged from 98 to 102% with mean coefficients of variation of 4.4% (within-day analyses) and 5.1% (day-to-day analyses). All three sensors displayed good stabilities when stored desiccated in the absence of buffer (>9 months).     

An amperometric hydrogen peroxide sensor based on immobilization of hemoglobin in poly(o-aminophenol) film at iron-cobalt hexacyanoferrate-modified gold electrode

A series of hybrid iron-cobalt hexacyanoferrate (FeCoHCF) films were electrodeposited on gold electrodes from solutions containing 6mM Fe(CN)(6)(3-) with different concentrations of Co(2+) and Fe(3+). FeCoHCF films deposited from solutions with different molar ratios of iron were studied by cyclic voltammetry, and their solid states were characterized by Fourier transform infrared spectroscopy. The kind of FeCoHCF film that deposited from a solution with a molar ratio of iron of 0.4 showed the largest response current to H(2)O(2) and was characterized by energy-dispersive X-ray spectroscopy. Therefore, the optimized FeCoHCF film was combined with nonconducting poly(o-aminophenol) (POAP) film that entrapped the hemoglobin (Hb) to construct hydrogen peroxide biosensor. The response current of the Hb/POAP/FeCoHCF/Au electrode (29.8 nA) was nearly 40 and was 1.5 times that of the Hb/POAP/Au (0.7 nA) and POAP/FeCoHCF/Au (20 nA) electrodes, respectively. The Michaelis-Menten constant of Hb in the Hb/POAP/FeCoHCF/Au film was 9.31 mM. These results show that the immobilized Hb in the Hb/POAP/FeCoHCF/Au film exhibits higher catalytic activity and larger response current to H(2)O(2) by the mediation of FeCoHCF. In addition, effects of applied potential, solution pH, and electroactive interferent on the response current of the Hb/POAP/FeCoHCF/Au electrode were investigated in detail.     

Self-assembled films of hemoglobin/laponite/chitosan: application for the direct electrochemistry and catalysis to hydrogen peroxide

A highly stable biological film was formed on the functional glassy carbon electrode (GCE) via step-by-step self-assembly of chitosan (CHT), laponite, and hemoglobin (Hb). Cyclic voltammetry (CV) of the Hb/laponite/CHT/GCE showed a pair of stable and quasi-reversible peaks for the Hb-Fe(III)/Fe(II) redox couple at about -0.035 V versus a saturated calomel electrode in pH 6.0 phosphate buffer at a scan rate of 0.1 V s(-1). The electrochemical reaction of Hb entrapped on the laponite/CHT self-assembled film exhibited a surface-controlled electrode process. The formal potential of the Hb-heme-Fe(III)/Fe(II) couple varied linearly with the increase of pH over the range of 3.0-8.0 with a slope of -63 mV pH(-1), which implied that an electron transfer was accompanied by single-proton transfer in the electrochemical reaction. The position of the Soret absorption band of this self-assembled Hb/laponite/CHT film suggested that the entrapped Hb kept its secondary structure similar to its native state. The self-assembled film showed excellent long-term stability, the CV peak potentials kept in the same positions, and the cathodic peak currents retained 90% of their values after 60 days. The film was used as a biological catalyst to catalyze the reduction of hydrogen peroxide. The electrocatalytic response showed a linear dependence on the H2O2 concentration ranging widely from 6.2 x 10(-6) to 2.55 x 10(-3) M with a detection limit of 6.2 x 10(-6) M at 3 sigma.     

Characterization of the biochemical behavior of glucose oxidase entrapped in a polypyrrole film

This article reports the characterization of the biochemical behavior of glucose oxidase entrapped in polypyrrole. The immobilization of glucose oxidase in a polypyrrole film was performed by entrapment during the electropolymerization of pyrrole at a platinum electrode poised at 0.65 V vs. SCE in aqueous solution in a one-compartment electrochemical cell. Thin films of polypyrrole (0.11 mum) were obtained and the entrapped enzyme obeyed Michaelis kinetics, indicating no diffusional constraints of the substrate. Our results indicate that the entrapped glucose oxidase is more resistant to denaturation conditions such as alkaline pH and temperature (50 and 60 degrees C) than the soluble form of the enzyme. The autoinactivation constant for the entrapped enzyme was also determined in presence of 0.25M of glucose and was 6.19 x 10(-4) min(-1), i.e., corresponding to a half-life value of 20 h. The results reported here show clearly that polypyrrole matrix has a strong stabilizing effect on the stucture and on the activity of glucose oxidase.     

Label-free electrochemical measurement of protein tyrosine kinase activity and inhibition based on electro-catalyzed tyrosine signaling

A novel label-free electrochemical method for measuring the activity of protein tyrosine kinases (PTK) has been developed. Epidermal growth factor receptor (EGFR), a typical PTK associated with a large percentage of all solid tumors, was used as the model kinase. Poly(glu, tyr) (4:1) peptide, as a substrate of EGFR, was covalently immobilized on the surface of indium tin oxide (ITO) electrode by silane chemistry. The tyrosine (Tyr) residue in the polypeptide served as an electrochemical signal reporter. Its voltammetric current was catalyzed by a dissolved electron mediator Os(bpy)(3)(2+) (bpy=2,2'-bipyridine) for increased sensitivity. Phosphorylation of the Tyr led to a loss of its electrochemical current, thus providing a sensing mechanism for PTK activity. Experimental conditions for the silanization of ITO surface and immobilization of polypeptide were investigated in details to facilitate the generation of Tyr electrochemical signal. The proposed biosensor exhibited high sensitivity and excellent stability. The limit of detection for EGFR was 1 UmL(-1). Furthermore, this biosensor can also be used for quantitative analysis of kinase inhibition. On the basis of the inhibitor concentration dependent electrochemical signal, the half-maximal inhibition value IC(50) of three EGFR inhibitors, PD-153035, OSI-774 and ZD-1839, and their corresponding inhibition constants K(i) were estimated, which were in agreement with those obtained from the conventional kinase assay. This electrochemical biosensor can be implemented in an array format for the high throughput assay of in vitro PTK activity and PTK inhibitors screening for practical diagnostic application and drug discovery.     

Conduction and photoelectrochemical properties of monomeric and electropolymerized tetraruthenated porphyrin films.

The influence of the preparation method on the structure, conduction and photoelectrochemical properties of monomeric and polymeric tetraruthenated porphyrin films on ITO glass and nanocrystalline TiO2 has been investigated. The films were characterized by STM, MAC mode SFM, cyclic voltammetry, electrochemical impedance spectroscopy (EIS) and combined electro-/photoelectrochemical techniques. The electronic diffusion coefficient D(e)C(m)2 of the films differed by three to four orders of magnitude depending on the procedure employed for the deposition process. The photoelectrochemical properties were evaluated either: by depositing the films directly on transparent ITO electrodes, under an applied bias potential and presence of O2 as electron acceptor; or by depositing the porphyrin material on nanocrystalline TiO2 in a Gr?tzel-type cell. In the first case the porphyrin films exhibited a typical p-type semiconductor behavior described by a Schottky junction model, while in the second the films behaved as a sensitizer of an n-type semiconductor. The photoelectrochemical properties of the porphyrin films and their performance as sensitizer in Gr?tzel-type cells were found to be strongly dependent on the conductivity and packing characteristics of the material. Semi-empirical calculations were performed by modified MM2 and ZINDO/S methods, in order to simulate the packing and electronic structures of the tetraruthenated porphyrin.     

Cholesterol biosensors prepared by layer-by-layer technique

The analysis of formation, deposition and characterization of cholesterol oxidase (COX) layer-by-layer films were performed. Initially, a layer of polyanion, poly(styrene sulfonate) (PSS) was adsorbed followed by a layer of polycation, poly(ethylene imine) (PEI) on each solid substrate from aqueous solutions. The alternating layers were formed by consecutive adsorption of polycations (PEI) and negatively charged proteins (COX) and cholesterol esterase (CE). A strong interaction between protein and polyelectrolyte improves the stability of the alternating multilayer; however, it can change a native protein conformation and impair the protein activity. The PSS/PEI/COX, PSS/PEI/COX/PEI/CE, PSS/PEI/COX-CE/PEI etc. layered structures were prepared on the surface of a platinum electrode, ITO coated glass plate, quartz crystal microbalance, quartz plates, mica and silicon substrates. Optical and gravimetric measurements based on an ultraviolet–visible absorption spectroscopy and a quartz crystal microbalance revealed that the enzyme multilayers thus prepared consist of molecular layered of the proteins. The surface morphology of such bilayer films was investigated by using atomic force microscopy. The electrochemical redox processes of the enzyme-layered films deposited either on platinum or ITO coated glass plate were investigated. The response current of cholesterol oxidase electrode with concentration of cholesterol was investigated at length.     

Polyaniline Langmuir-Blodgett film based aptasensor for ochratoxin A detection

Ochratoxin A (OTA) produced by Aspergillus Ochraceus and Penicillium verrucosum is a very dangerous toxin due to its toxic effects in human beings and its presence in a wide range of food products and cereals. A Langmuir-Blodgett (polyaniline (PANI)-stearic acid (SA)) film based highly sensitive and robust impedimetric aptasensor has been developed for ochratoxin A (OTA) detection. DNA Aptamer (Apt-DNA) specific to OTA has been covalently immobilized onto mixed Langmuir-Blodgett (LB) monolayer comprising of PANI-SA deposited onto indium tin-oxide (ITO) coated glass plates. This Apt-DNA/PANI-SA/ITO aptaelectrode has been characterized using scanning electron microscopy, Fourier transform-infrared spectroscopy, contact angle measurements, cyclic voltammetry and electrochemical impedance spectroscopy, respectively. The Apt-DNA/PANI-SA/ITO aptasensor shows detection of OTA by electrochemical impedance spectroscopy in the linear range of 0.0001 μg/ml (0.1 ng/ml) to 0.01 μg/ml (10 ng/ml) and 1 μg/ml-25 μg/ml with detection limit of 0.1 ng/ml in 15 min. The Apt-DNA/PANI-SA/ITO aptasensor can be reused ～13 times. The binding or affinity constant (K(a)) of aptamer with OTA, calculated using Langmuir adsorption isotherm, is found be 1.21×10(7) M(-1).     

Asymmetry of lysophosphatidylcholine/cholesterol vesicles is sensitive to cholesterol modulation

Sonication of lysophosphatidylcholine (lysoPC; 20 mumol/mL) and cholesterol (chol) in aqueous medium produces lamellar structures over a wide range of concentrations. From 25 to 47 mol % cholesterol, electron microscopy (EM) after negative staining showed extended stacklike lamellae about 40 A thick. From 50 to 60 mol % chol, freeze-fracture EM showed homogeneous populations of small unilamellar vesicles averaging 260-310 A in diameter. Phosphorus-31 nuclear magnetic resonance was used to characterize the stacklike lamellae and to measure the distribution of the lysophospholipid between the outer and inner leaflet of the vesicles as a function of sterol concentration. We found that in lysoPC/chol dispersions containing less than equimolar amounts of cholesterol (25-47 mol %), the entire phosphorus signal (40.5 ppm) was shifted downfield by 10.5 ppm upon addition of Pr3+ (2.4 mM), consistent with the stacklike lamellar structures in which all lysoPC head groups are accessible to the ions. By contrast, addition of Pr3+ to lysoPC/chol vesicles containing equimolar or higher amounts of cholesterol (up to 60 mol %) gave rise to two phosphorus peaks. The more intense downfield signal (51.0 ppm) responsive to paramagnetic ions was assigned to lysoPC located in the outer vesicle leaflet. The upfield signal (40.5 ppm), which was not affected by the ions, was assigned to inside lysoPC. For lysoPC/chol (1:1) vesicles, an outside to inside lysophospholipid ratio (Ro/i) of 6.5 was determined. Essentially the same Ro/i value (6.7) was obtained on lysoPC/chol (1:1) vesicles which after dialysis contained only entrapped Pr3+.(ABSTRACT TRUNCATED AT 250 WORDS)     

Removal of Hg2+ as an electron acceptor coupled with power generation using a microbial fuel cell

In this study, removal of Hg(2+) as an electron acceptor of a microbial fuel cell (MFC) was successfully achieved. The initial pH affected the removal efficiency of Hg(2+) from electrochemical and chemical reactions. The effluent Hg concentrations for initial Hg(2+) concentration of 50mg/L after a 5-h reaction were 3.08 ± 0.07, 4.21 ± 0.34, 4.84 ± 0.00, and 5.25 ± 0.36 mg/L for initial pH of 2, 3, 4, and 4.8, respectively. For 10-h reaction, the effluent Hg concentration was in the range of 0.44-0.69 mg/L, for different initial Hg(2+) concentrations (25, 50, and 100mg/L). Lower initial pH and higher Hg(2+) concentration resulted in larger maximum power density. A maximum power density of 433.1 mW/m(2) was achieved from 100mg/L Hg(2+) at pH 2.     

Inlaid Nd-substituted bismuth titanate nanoplates for protein immobilization and Nd-controlled electrochemical properties

Neodymium (Nd) substituted bismuth titanate (Bi(4-x)Nd(x)Ti(3)O(12), BNTO-x) nanoplates inlaid one another were prepared by sol-gel hydrothermal method, which was explored for protein immobilization and biosensor fabrication. Comparative experiments witnessed that Bi(3+) ions in bismuth titanate (Bi(4)Ti(3)O(12), BTO) were successfully substituted with Nd(3+) ions, and the electrochemical properties of the Hb-Chi-BNTO biosensors closely depended on the Nd(3+) ion content. With increasing the Nd(3+) doping content, the electrochemical performance of the Hb-Chi-BNTO-x biosensors showed regularly variable. Moreover, compared with the Hb-Chi-BTO and other Hb-Chi-BNTO-x biosensors, the Hb-Chi-BNTO-0.85 biosensor had more excellent electrochemical and electrocatalytic properties such as stronger redox peak currents (approximately three-fold), smaller peak-to-peak separation (50 mV), larger heterogeneous electron transfer rate (14.1 ± 3.8s(-1)), higher surface concentration of electroactive redox protein (about 8.16 × 10(-11)mol/cm(2)), and better reproducibility and stability. The Nd-depended electrochemical properties of the Hb-Chi-BNTO biosensors may open up a new idea for designing third-generation electrochemical biosensors, and the BNTO-0.85-based biosensor is also expected to find potential applications in many areas such as biomedical, food, and environmental detection.