Influence of protein surface morphology on the ultrafiltration flux resistance of bovine serum albumin.

The effect of added ethanol and (NH(4))(2)SO(4) on the flux decline index (FDI) of bovine serum albumin (BSA) and a fatty acid-poor derivative (BSA/FAP) was examined. Ternary phase diagrams of the two protein species indicated that the concentration polarization (CP) layer on the surface of a nonadsorbing 10 000 MWCO regenerated cellulose membrane had principally a packed bed structure up to 33 wt % ethanol and 21 wt % (NH(4))(2)SO(4). Intrinsic viscosity and turbidity analysis were conducted to determine the degree of intra- and interprotein interactions within this packed bed morphology. With BSA/FAP, the effects of these two interactions tended to counterbalance each other, so the FDI of this protein was not strongly influenced by solute addition. In contrast, the adsorption of fatty acids to BSA caused the protein to expand, producing a less rigid CP layer with a higher FDI. However, the addition of ethanol led to protein compression, reducing this effect. The presence of fatty acids also produced a more associated BSA in salt solution, which increased flux resistance. The results obtained for both proteins indicate that an FDI minimum is observed when a noninteraction hard sphere structure is present in the CP layer.     

Effects of arginine on heat-induced aggregation of concentrated protein solutions

Arginine is one of the commonly used additives to enhance refolding yield of proteins, to suppress aggregation of proteins, and to increase solubility of proteins, and yet the molecular interactions that contribute to the role of arginine are unclear. Here, we present experiments, using bovine serum albumin (BSA), lysozyme (LYZ), and β-lactoglobulin (BLG) as model proteins, to show that arginine can enhance heat-induced aggregation of concentrated protein solutions, contrary to the conventional belief that arginine is a universal suppressor of aggregation. Results show that the enhancement in aggregation is caused only for BSA and BLG, but not for LYZ, indicating that arginine's preferential interactions with certain residues over others could determine the effect of the additive on aggregation. We use this previously unrecognized behavior of arginine, in combination with density functional theory calculations, to identify the molecular-level interactions of arginine with various residues that determine arginine's role as an enhancer or suppressor of aggregation of proteins. The experimental and computational results suggest that the guanidinium group of arginine promotes aggregation through the hydrogen-bond-based bridging interactions with the acidic residues of a protein, whereas the binding of the guanidinium group to aromatic residues (aggregation-prone) contributes to the stability and solubilization of the proteins. The approach, we describe here, can be used to select suitable additives to stabilize a protein solution at high concentrations based on an analysis of the amino acid content of the protein.     

Effect of ion binding on protein transport through ultrafiltration membranes

Electrostatic interactions can have a significant impact on protein transmission through semipermeable membranes. Experimental data for the transport of bovine serum albumin (BSA) through a polyethersulfone ultrafiltration membrane were obtained in different salt solutions over a range of pH and salt concentrations. Net BSA charge under the same conditions was evaluated from mobility data measured by capillary electrophoresis. The results show that specific ionic composition, in addition to solution pH and ionic strength, can strongly affect the rate of protein transport through semipermeable ultrafiltration membranes. The effects of different ions on BSA sieving are due primarily to differences in ion binding to the protein, which leads to significant differences in the net protein charge at a given pH and ionic strength. This effect could be described in terms of an effective protein radius, which accounts for the electrostatic exclusion of the charged protein from the membrane pores. These results provide important insights into the nature of the electrostatic interactions in membrane systems.     

Protein adsorption at solid-liquid interfaces: Part II--Adsorption from binary protein mixture

Extent of adsorption of proteins at alumina-water interface from solutions containing binary mixture of beta-lactoglobulin and bovine serum albumin (BSA), beta-lactoglobulin and gelatin, and gelatin and bovine serum albumin has been estimated as functions of protein concentrations at varying pH, ionic strength, temperature and weight fraction ratios of protein mixture. The extent of adsorption (gamma lacw) of lactoglobulin in the presence of BSA increases with increase of protein concentration (Clac) until it reaches a maximum but a fixed value gamma lacw(m). Extent of adsorption gamma serw also initially increases with increase of protein concentrations until it reaches maximum value gamma serw(m). Beyond these protein concentrations, adsorbed BSA is gradually desorbed due to the preferential adsorption of lactoglobulin from the protein mixture. In many systems, gamma serw at high protein concentrations even becomes negative due to the strong competition of BSA and water for binding to the surface sites in the presence of lactoglobulin. For lactoglobulin-gelatin mixtures, adsorption of both proteins is enhanced as protein concentration is increased until limiting values for adsorption are reached. Beyond the limiting value, lactoglobulin is further accumulated at the interface without limit when protein concentration is high. For gelatin-albumin mixtures, extent of gelatin adsorption increases with increase in the adsorption of BSA. The limit for saturation of adsorption for gelatin is not reached for many systems. At acid pH, adsorbed BSA appears to be desorbed from the surface in the presence of gelatin. From the results thus obtained the role of electrostatic and hydrophobic effects in controlling the adsorption process has been analysed.     

Protein modified- and membrane electrodes: strategies for the development of biomolecular sensors

Different procedures used for constructing protein/enzyme-modified electrodes are examined, in particular adsorption, covalent attachment and film deposition. The performances of such modified electrodes with electroactive proteins or enzymes attached to their active surface are examined, especially in the case of c-type cytochromes, hydrogenases and glucose oxidase. Another strategy presented in this review consists of the use of membrane electrodes with an electroactive protein imprisoned between a dialysis membrane and the electrode surface. The versatility and other advantages of such a procedure are underlined. Applications of membrane electrodes to the bioremediation of soils and effluents and as models for investigating interactions between proteins and soils are described.     

Control of protein adsorption on functionalized electrospun fibers

Electrospun fibers that are protein resistant and functionalized with bioactive signals were produced by solution electrospinning amphiphilic block copolymers. Poly (ethylene glycol)-block-poly(D,L-lactide) (PEG-b-PDLLA) was synthesized in two steps, with a PEG segment of 10 kDa, while the PDLLA block ranged from 20 to 60 kDa. Depending on the PEG and PDLLA segment ratio, as well as solvent selection, the hydrophilicity and protein adsorption could be altered on the electrospun mesh. Furthermore, an alpha-acetal PEG-b-PDLLA was synthesized that allowed the conjugation of active molecules, resulting in surface functionalization of the electrospun fiber. Electrospun material with varying morphologies and diameter were electrospun from 10, 20, and 30 wt.% solutions. Sessile drop measurements showed a reduction in the contact angle from 120 degrees for pure poly(D,L-lactide) with increasing PEG/PDLLA ratio. All electrospun block PEG-b-PDLLA fibers had hydrophilic properties, with contact angles below 45 degrees . The fibers were collected onto six-arm star-poly(ethylene glycol) (star-PEG) coated silicon wafers and incubated with fluorescently labeled proteins. All PEG-b-PDLLA fibers showed no detectable adsorption of bovine serum albumin (BSA) independent of their composition while a dependence between hydrophobic block length was observed for streptavidin adsorption. Fibers of block copolymers with PDLLA blocks smaller than 39 kDa showed no adsorption of BSA or streptavidin, indicating good non-fouling properties. Fibers were surface functionalized with N(epsilon)-(+)-biotinyl-L-lysine (biocytin) or RGD peptide by attaching the molecule to the PEG block during synthesis. Protein adsorption measurements, and the controlled interaction of biocytin with fluorescently labeled streptavidin, showed that the electrospun fibers were both resistant to protein adsorption and are functionalized. Fibroblast adhesion was contrasting between the unfunctionalized and RGD-coupled electrospun fabrics, confirming that the surface of the fibers was functionalized. The PEG-b-PDLLA surface functionalized electrospun fibers are promising substrates for controlling cell-material interactions, particularly for tissue-engineering applications.     

Mechanism of bovine serum albumin aggregation during ultrafiltration

Protein fouling is a critical problem for ultrafiltration. In this study, we adopted bovine serum albumin (BSA) as a model protein and polysulfone membrane as a typical ultrafiltration membrane. We then investigated the factors of the protein denaturation and aggregation, such as stirring shear stress and intermolecular exchange of disulfide during ultrafiltration, and discussed the BSA fouling mechanism. Fourier transform-infrared analysis revealed that magnetic stirring did not cause any difference in the secondary structural change of BSA gel-like deposits on the ultrafiltration membrane. BSA aggregates were collected from BSA gel-like deposits on the ultrafiltration membrane by centrifugation. Polyacrylamide gel electrophoresis in SDS analysis of BSA aggregates proved that the major binding of the BSA aggregates involved intermolecular disulfhydryl binding and that capping the free thiol group in BSA molecules with cysteine induced a remarkable decrease in the amount of the BSA aggregates during ultrafiltration. We concluded that one of the main factors in the BSA aggregation during ultrafiltration is the intermolecular exchange of disulfide through cysteinyl residue. We also found that the BSA aggregation caused a decrease in alpha-helix from 66% to 50% and an increase in beta-sheet from 20% to 36%, which was presumably because the cysteine residues associated with the intermolecular disulfide bonds had been located in alpha-helices. Copyright John Wiley & Sons, Inc.     

Selective protein separations using Formed-In-Place anion exchange membranes.

Anion exchange membranes prepared by adsorption of polymers on Formed-In-Place microfiltration substrates were formed and ion-exchange separations of solutions containing two proteins were determined by ion exchange membrane sequential separation procedures, similar to affinity membrane separation procedures. Representative ion exchange separation processes utilizing adsorbed poly(ethylene imine) (PEI) as the ion exchange membrane for the separation of the components of solutions containing two proteins, bovine serum albumin (BSA) and lysozyme and ovalbumin and lysozyme, are described. The stability of the PEI adsorbed layer, binding characteristics of the BSA to the membrane and purification properties of the procedure were determined.     

Protein adsorption at solid-liquid interfaces: Part III--Adsorption from ternary protein mixture.

Simultaneous adsorption of bovine serum albumin (BSA), beta-lactoglobulin and gelatin from aqueous solutions of their ternary mixture to the alumina-water interface has been studied as a function of protein concentration at different values of pH, ionic strength, temperature and weight fraction ratios of proteins. At a fixed weight fraction of beta-lactoglobulin, preferential adsorption (gamma w(lac)) of this protein significantly depends on the amounts of BSA and gelatin present in the solution before adsorption. At higher ranges of protein concentrations, extent of adsorption (gamma w(ser)) of BSA decreases sharply with increase of gamma w(lac) until gamma w(ser) becomes significantly negative, thereby indicating that beta-lactoglobulin and water preferentially adsorbed at the interface are responsible for complete displacement of BSA from the surface. On the other hand, adsorption (gamma w(gel)) of gelatin under similar situation increases mutually with increase in the values of gamma w(lac) in many systems. In few systems, gamma w(gel) also decreases with increase of gamma w(lac) depending upon solution parameters. At pH 5.2, increase of ionic strength and temperature, respectively, increases the extent of adsorption of each protein in the mixture considerably. Extents of adsorption of all proteins are observed to increase when pH is changed from 5.2 to 6.4. The affinities of different proteins in the mixture are expressed in unified scales either in terms of maximum extents of total adsorption or in terms of standard free energies of adsorption of protein mixtures with respect to surface saturation.     

A quantitative and selective chromatography method for determining coverages of multiple proteins on surfaces

Competitive protein adsorption plays a key role in the surface hemocompatibility of biological implants. We describe a quantitative chromatography method to measure the coverage of multiple proteins physisorbed to surfaces. In this method adsorbed proteins are displaced by CHAPS (3-[(3-cholamidopropyl)dimethylammonio]-1-propanesulfonate) and then analyzed by high performance liquid chromatography to separate and quantify the individual proteins, in this case bovine serum albumin (BSA) and bovine fibrinogen (Fg). CHAPS displaced over 95% of the adsorbed proteins and was easily removed from solution by dialysis. This method was tested by measuring the coverage of BSA, 66 kDa, and Fg, 340 kDa, simultaneously adsorbed from solutions with concentration of 20 microg/ml, on bare and dextranized silicon. Relative to silicon, the dextranized surfaces were found to strongly inhibit protein adsorption, decreasing BSA and Fg coverages by 76 and 60%, respectively.     

Interactions of lens proteins. Ultrafiltration is unsuitable to detect self- or mixed-association

Crystallins from calf lens were subjected to ultrafiltration through an Amicon XM-300 membrane to determine whether specific interactions between identical proteins (self-association) or different proteins (mixed-association) could be detected and quantified. Single crystallins at different concentrations, simple mixtures and total lens extracts were studied separately. alpha-Crystallin (Mr 800 000) is nearly fully retained (greater than 95%) by XM-300. Retention of beta-crystallins (Mr 50 000-200 000) is found to be much higher than expected from their molecular weights. Ultrafiltration of gamma-crystallin (Mr 20 000) solutions of 1.0-22.6 g/l shows that retention increases as a function of protein concentration. In solutions of single crystallins, self-association effects could not be separated from concentration polarization effects at the membrane surface. In mixtures of crystallins, mixed-association could not be separated from self-association, concentration polarization and excluded volume effects on self-association.     

PM-IRRAS investigation of the interaction of serum albumin and fibrinogen with a biomedical-grade stainless steel 316LVM surface

Polarization modulation infrared reflection absorption spectroscopy (PM-IRRAS) was applied to investigate the interaction of bovine serum albumin (BSA) and fibrinogen with a biomedical-grade 316LVM stainless steel surface, in terms of the adsorption thermodynamics and adsorption-induced secondary structure changes of the proteins. Highly negative apparent Gibbs energy of adsorption values revealed a spontaneous adsorption of both proteins onto the surface, accompanied by significant changes in their secondary structure. It was determined that, at saturated surface coverages, lateral interactions between the adsorbed BSA molecules induced rather extensive secondary structure changes. Fibrinogen's two coiled coils appeared to undergo negligible secondary structure changes upon adsorption of the protein, while large structural rearrangements of the protein's globular domains occurred upon adsorption. The secondary structure of adsorbed fibrinogen was not influenced by lateral interactions between the adsorbed fibrinogen molecules. PM-IRRAS was deemed to be viable for investigating protein adsorption and for obtaining information on adsorption-induced changes in their secondary structures.     

Macromolecular crowding at membrane interfaces: adsorption and alignment of membrane peptides

Association of proteins to cellular membranes is involved in various biological processes. Various theoretical models have been developed to describe this adsorption mechanism, commonly implying the concept of an ideal solution. However, due to the two-dimensional character of membrane surfaces intermolecular interactions between the adsorbed molecules become important. Therefore previously adsorbed molecules can influence the adsorption behavior of additional protein molecules and their membrane-associated structure. Using the model peptide LAH₄, which upon membrane-adsorption can adopt a transmembrane as well as an in-planar configuration, we carried out a systematic study of the correlation between the peptide concentration in the membrane and the topology of this membrane-associated polypeptide. We could describe the observed binding behavior by establishing a concept, which includes intermolecular interactions in terms of a scaled particle theory.High surface concentration of the peptide shifts the molecules from an in-planar into a transmembrane conformation, a process driven by the reduction of occupied surface area per molecule. In a cellular context, the crowding-dependent alignment might provide a molecular switch for a cell to sense and control its membrane occupancy. Furthermore, crowding might have pronounced effects on biological events, such as the cooperative behavior of antimicrobial peptides and the membrane triggered aggregation of amyloidogenic peptides.     

Separation albumin-PEG: transmission of PEG through ultrafiltration membranes

Transmission of polyethylene glycol (PEG) through ultrafiltration membranes has been studied under various operating conditions of pressure, crossflow, and concentration, using different membranes cut-offs and two module designs with the aim of understanding the separation of PEG from BSA. The influence of protein adsorption and fouling of the choice of a membrane has also been considered. Retention depends in general on the molecule to average pore size ratio, as expected, but also on concentration polarization. Accordingly, all operating and design parameters favoring concentration polarization lead to higher transmission. At high fluxes, flexible macromolecules can pass through the membrane, even if the random coil is larger than the apparent average pore. From a process selectivity point of view, the best way to separate PEG from BSA would be to use a membrane totally retaining BSA and to enhance concentration polarization of PEG. Unfortunately, such conditions also increase fouling and concentration polarization by BSA, which limits flux and thus PEG concentration polarization and transmission. Consequences of such conditions on separation efficiency are discussed. (c) 1993 Wiley & Sons, Inc.     

The investigation of protein adsorption behaviors on different functionalized polymers films

The adsorption of BSA and fibrinogen onto plasma-polymerized di-(ethylene glycol) vinyl ether, allylamine, and maleic anhydride films were investigated in detail by surface plasmon resonance spectroscopy (SPR). The chemical properties of the plasma polymers were initially determined by the plasma deposition conditions during the generation procedure. The analysis of the chemical structure of the films and the refractive index of plasma polymers in aqueous solution was carried out using Fourier transform infrared spectroscopy and waveguide mode spectroscopy, respectively. Using water contact angle measurement, the surface wettability of plasma polymers was also characterized. These properties have a critical influence on the behavior of protein adsorption on the surface of the plasma polymers. Protein adsorption was found to depend not only on the types of functionalized groups, but also on the plasma polymer thickness since the protein molecules penetrate into the plasma polymer network bulk. According to the size of protein molecules in aqueous solution and the amount of adsorbed proteins observed by SPR, the conformational changes of proteins could be deduced.     

Quantitative analysis of membrane fouling by protein mixtures using MALDI-MS

Binary aqueous solutions of bovine serum albumin (BSA) and beta-lactoglobulin (bLG) were subject to flux-stepping and constant flux ultrafiltration to identify the apparent critical flux and to study the mechanisms and factors affecting fouling when the membrane is permeable to one protein component. Membranes from these filtration experiments were analyzed using matrix-assisted laser desorption ionization mass spectrometry (MALDI-MS) to locate and quantify levels of fouling below and above the apparent critical flux. Hydrophilic (PLTK) regenerated cellulose and hydrophobic (PBTK) polysulfone asymmetric membranes were used, both of 30 kDa nominal molecular weight cut-off. For the hydrophilic PLTK membrane, protein deposition was shown to depend on electrostatic forces, exhibiting little or no fouling when the proteins had the same charge sign as that of the membrane. This was found to apply for both dilute equal mass-per-unit-volume and equimolar binary mixtures. For the PBTK membrane, hydrophobic protein-membrane attractive forces were sufficiently strong to cause deposition of bLG even in the presence of repulsive electrostatic forces. For the PBTK membrane deposition exceeded monolayer coverage below and above apparent critical flux conditions but for the PLTK membrane this generally occurred when the apparent critical flux was exceeded. MALDI-MS was shown to be a facile direct analytical technique for individually quantifying adsorbed proteins on membrane surfaces at levels as low as 50 fmol/mm(2). The high levels of compound specificity inherent to mass spectrometry make this approach especially suited to the quantification of individual components in mixed deposits. In this study, MALDI-MS was found to be successful in identifying and quantifying the protein species responsible for fouling.     

SANS/SAXS study of the BSA solvation properties in aqueous urea solutions via a global fit approach

We report on the solvation properties and intermolecular interactions of a model protein (bovine serum albumine, BSA) in urea aqueous solutions, as obtained by combining small-angle neutron and X-ray scattering experiments. According to a global fit strategy, all the whole set of scattering curves are analysed by considering a unique model which includes the BSA structure, the protein-protein interactions and the thermodynamic exchange process of water/urea molecules at the protein solvent interface. As a main result, the equilibrium constant that accounts for the difference in composition between the bulk solvent and the protein solvation layer is derived. Results confirm that urea preferentially sticks to the protein surface, inducing a noticeable change in both the repulsive and the attractive interaction potentials.     

Protein interactions with nanosized hydrotalcites of different composition

Nanosized hydrotalcite-like compounds (HTlc) with different chemical composition were prepared and used to study protein adsorption. Two soft proteins, myoglobin (Mb) and bovine serum albumin (BSA), were chosen to investigate the nature of the forces controlling the adsorption and how these depend on the chemical composition of the support. Both proteins strongly interact with HTlc exhibiting in most cases a Langmuir-type adsorption. Mb showed a higher affinity for Nickel Chromium (NiCr-HTlc) than for Nickel Aluminum (NiAl-HTlc), while for BSA no significant differences between supports were found. Adsorption experiments in the presence of additives showed that proteins exhibited different types of interactions onto the same HTlc surface and that the adsorption was strongly suppressed by the addition of disodium hydrogen phosphate (Na₂HPO₄). Atomic force microscopy images showed that the adsorption of both proteins onto nanoparticles was followed by the aggregation of biocomposites, with a more disordered structure for BSA. Fluorescence measurements for adsorbed Mb showed that the inorganic nanoparticles induced conformational changes in the biomolecules; in particular, the interactions with HTlc surface quenched the tryptophan fluorescence and this process was particularly efficient for NiCr-HTlc. The adsorption of BSA onto the HTlc nanoparticles induced a selective quenching of the exposed fluorescent residues, as indicated by the blue-shift of the emission spectra of tryptophan residues and by the shortening of the fluorescence decay times.     

Competitive adsorption of human fibrinogen on an amorphic quartz surface

The kinetics of adsorption of fibrinogen on the surface of amorphous quartz from binary solutions containing human serum albumin and gamma-globulin was studied by the method of fluorescence of total internal reflection. A model of energetically nonhomogeneous interactions in the surface/protein system was used to explain the mechanism of competitive adsorption of proteins.     

Method for printing functional protein microarrays

Piezoelectric dispensing of proteins from borosilicate glass capillaries is a popular method of protein biochip fabrication that offers the advantages of sample recovery and noncontact with the printing substrate. However, little regard has been given to the quantitative aspects of dispensing minute volumes (1 nL or less) at the low protein concentrations (20 micrograms/mL or less) typically used in microprinting. Specifically, loss of protein sample due to nonspecific adsorption to the glass surface of the dispensing capillaries can limit the amount of protein delivered to the substrate. We demonstrate the benefits of a low ionic strength buffer containing the carrier protein BSA that effectively minimizes the ionic strength-dependent phenomenon of nonspecific protein adsorption to borosilicate glass. Over the concentration range of 20-2.5 micrograms/mL, the dispensing of a reference IgG in 10 mM PBS including 0.1% BSA resulted in the deposition of 3.6- to 44-fold more IgG compared to the deposition of IgG in standard 150 mM PBS in the absence of BSA. Furthermore, when the IgG was dispensed with carrier protein, the resulting spots exhibited a more uniform morphology. In a direct immunoassay for cholera toxin, capture antibody spots dispensed in 10 mM PBS containing 0.1% BSA produced fluorescent signals that were 2.8- to 4.3-fold more intense than antibody spots that were dispensed in 150 mM PBS without BSA. Interestingly, no differences were observed in the specific activities of the capture antibodies as a result of printing in the different buffers. The implications of these results on the future development of protein biochips are discussed.