Butanol production from wheat straw hydrolysate using <Emphasis Type="Italic">Clostridium beijerinckii</Emphasis>

In these studies, butanol (acetone butanol ethanol or ABE) was produced from wheat straw hydrolysate (WSH) in batch cultures using Clostridium beijerinckii P260. In control fermentation 48.9 g L⁻¹ glucose (initial sugar 62.0 g L⁻¹) was used to produce 20.1 g L⁻¹ ABE with a productivity and yield of 0.28 g L⁻¹ h⁻¹ and 0.41, respectively. In a similar experiment where WSH (60.2 g L⁻¹ total sugars obtained from hydrolysis of 86 g L⁻¹ wheat straw) was used, the culture produced 25.0 g L⁻¹ ABE with a productivity and yield of 0.60 g L⁻¹ h⁻¹ and 0.42, respectively. These results are superior to the control experiment and productivity was improved by 214%. When WSH was supplemented with 35 g L⁻¹ glucose, a reactor productivity was improved to 0.63 g L⁻¹ h⁻¹ with a yield of 0.42. In this case, ABE concentration in the broth was 28.2 g L⁻¹. When WSH was supplemented with 60 g L⁻¹ glucose, the resultant medium containing 128.3 g L⁻¹ sugars was successfully fermented (due to product removal) to produce 47.6 g L⁻¹ ABE, and the culture utilized all the sugars (glucose, xylose, arabinose, galactose, and mannose). These results demonstrate that C. beijerinckii P260 has excellent capacity to convert biomass derived sugars to solvents and can produce over 28 g L⁻¹ (in one case 41.7 g L⁻¹ from glucose) ABE from WSH. Medium containing 250 g L⁻¹ glucose resulted in no growth and no ABE production. Mixtures containing WSH + 140 g L⁻¹ glucose (total sugar approximately 200 g L⁻¹) showed poor growth and poor ABE production. Mention of trade names or commercial products in this article is solely for the purpose of providing scientific information and does not imply recommendation or endorsement by the United States Department of Agriculture.     

Cellulosic Butanol (ABE) Biofuel Production from Sweet Sorghum Bagasse (SSB): Impact of Hot Water Pretreatment and Solid Loadings on Fermentation Employing <Emphasis Type="Italic">Clostridium beijerinckii</Emphasis> P260

A novel butanol fermentation process was developed in which sweet sorghum bagasse (SSB) was pretreated using liquid hot water (LHW) pretreatment technique followed by enzymatic hydrolysis and butanol (acetone butanol ethanol (ABE)) fermentation. A pretreatment temperature of 200 °C resulted in the generation of a hydrolyzate that inhibited butanol fermentation. When SSB pretreatment temperature was decreased to 190 °C (0-min holding time), the hydrolyzate was successfully fermented without inhibition and an ABE productivity of 0.51 g L^?1 h^?1 was achieved which is comparable to the 0.49 g L^?1 h^?1 observed in the control fermentation where glucose was used as a feedstock. These results are based on the use of 86 g L^?1 SSB solid loadings in the pretreatment reactors. We were also able to increase SSB solid loadings from 120 to 200 g L^?1 in the pretreatment step (190 °C) followed by hydrolysis and butanol fermentation. As pretreatment solid loadings increased, ABE yield remained in the range of 0.38–0.46. In these studies, a maximum ABE concentration of 16.88 g L^?1 was achieved. Using the LHW pretreatment technique, 88.40–96.00 % of polymeric sugars (cellulose + hemicellulose) were released in the SSB hydrolyzate. The LHW pretreatment technique does not require chemical additions and is environmentally friendly, and the hydrolyzate can be used successfully for butanol fermentation.     

Butanol production by Clostridium beijerinckii ATCC 55025 from wheat bran

Wheat bran, a by-product of the wheat milling industry, consists mainly of hemicellulose, starch and protein. In this study, the hydrolysate of wheat bran pretreated with dilute sulfuric acid was used as a substrate to produce ABE (acetone, butanol and ethanol) using Clostridium beijerinckii ATCC 55025. The wheat bran hydrolysate contained 53.1 g/l total reducing sugars, including 21.3 g/l of glucose, 17.4 g/l of xylose and 10.6 g/l of arabinose. C. beijerinckii ATCC 55025 can utilize hexose and pentose simultaneously in the hydrolysate to produce ABE. After 72 h of fermentation, the total ABE in the system was 11.8 g/l, of which acetone, butanol and ethanol were 2.2, 8.8 and 0.8 g/l, respectively. The fermentation resulted in an ABE yield of 0.32 and productivity of 0.16 g l⁻¹ h⁻¹. This study suggests that wheat bran can be a potential renewable resource for ABE fermentation.     

Continuous acetone-butanol-ethanol fermentation using SO2-ethanol-water spent liquor from spruce

SO₂–ethanol–water (SEW) spent liquor from spruce chips was successfully used for batch and continuous production of acetone, butanol and ethanol (ABE). Initially, batch experiments were performed using spent liquor to check the suitability for production of ABE. Maximum concentration of total ABE was found to be 8.79 g/l using 4-fold diluted SEW liquor supplemented with 35 g/l of glucose. The effect of dilution rate on solvent production, productivity and yield was studied in column reactor consisting of immobilized Clostridium acetobutylicum DSM 792 on wood pulp. Total solvent concentration of 12 g/l was obtained at a dilution rate of 0.21 h⁻¹. The maximum solvent productivity (4.86 g/l h) with yield of 0.27 g/g was obtained at dilution rate of 0.64 h⁻¹. Further, to increase the solvent yield, the unutilized sugars were subjected to batch fermentation.     

Butanol production from sweet sorghum bagasse with high solids content: Part I—comparison of liquid hot water pretreatment with dilute sulfuric acid

In these studies, we pretreated sweet sorghum bagasse (SSB) using liquid hot water (LHW) or dilute H₂SO₄ (2 g L^?1) at 190°C for zero min (as soon as temperature reached 190°C, cooling was started) to reduce generation of sugar degradation fermentation inhibiting products such as furfural and hydroxymethyl furfural (HMF). The solids loading were 250–300 g L^?1. This was followed by enzymatic hydrolysis. After hydrolysis, 89.0 g L^?1 sugars, 7.60 g L^?1 acetic acid, 0.33 g L^?1 furfural, and 0.07 g L^?1 HMF were released. This pretreatment and hydrolysis resulted in the release of 57.9% sugars. This was followed by second hydrolysis of the fibrous biomass which resulted in the release of 43.64 g L^?1 additional sugars, 2.40 g L^?1 acetic acid, zero g L^?1 furfural, and zero g L^?1 HMF. In both the hydrolyzates, 86.3% sugars present in SSB were released. Fermentation of the hydrolyzate I resulted in poor acetone‐butanol‐ethanol (ABE) fermentation. However, fermentation of the hydrolyzate II was successful and produced 13.43 g L^?1 ABE of which butanol was the main product. Use of 2 g L^?1 H₂SO₄ as a pretreatment medium followed by enzymatic hydrolysis resulted in the release of 100.6–93.8% (w/w) sugars from 250 to 300 g L^?1 SSB, respectively. LHW or dilute H₂SO₄ were used to economize production of cellulosic sugars from SSB. © 2018 American Institute of Chemical Engineers Biotechnol. Prog., 34:960–966, 2018     

Acetone butanol ethanol (ABE) production from concentrated substrate: reduction in substrate inhibition by fed-batch technique and product inhibition by gas stripping

Acetone butanol ethanol (ABE) was produced in an integrated fed-batch fermentation-gas stripping product-recovery system using Clostridium beijerinckii BA101, with H₂ and CO₂ as the carrier gases. This technique was applied in order to eliminate the substrate and product inhibition that normally restricts ABE production and sugar utilization to less than 20 g l^–1 and 60 g l^–1, respectively. In the integrated fed-batch fermentation and product recovery system, solvent productivities were improved to 400% of the control batch fermentation productivities. In a control batch reactor, the culture used 45.4 g glucose l^–1 and produced 17.6 g total solvents l^–1 (yield 0.39 g g^–1, productivity 0.29 g l^–1 h^–1). Using the integrated fermentation-gas stripping product-recovery system with CO₂ and H₂ as carrier gases, we carried out fed-batch fermentation experiments and measured various characteristics of the fermentation, including ABE production, selectivity, yield and productivity. The fed-batch reactor was operated for 201 h. At the end of the fermentation, an unusually high concentration of total acids (8.5 g l^–1) was observed. A total of 500 g glucose was used to produce 232.8 g solvents (77.7 g acetone, 151.7 g butanol, 3.4 g ethanol) in 1 l culture broth. The average solvent yield and productivity were 0.47 g g^–1 and 1.16 g l^–1 h^–1, respectively.     

Engineering Clostridium acetobutylicum for production of kerosene and diesel blendstock precursors

Processes for the biotechnological production of kerosene and diesel blendstocks are often economically unattractive due to low yields and product titers. Recently, Clostridium acetobutylicum fermentation products acetone, butanol, and ethanol (ABE) were shown to serve as precursors for catalytic upgrading to higher chain-length molecules that can be used as fuel substitutes. To produce suitable kerosene and diesel blendstocks, the butanol:acetone ratio of fermentation products needs to be increased to 2–2.5:1, while ethanol production is minimized. Here we show that the overexpression of selected proteins changes the ratio of ABE products relative to the wild type ATCC 824 strain. Overexpression of the native alcohol/aldehyde dehydrogenase (AAD) has been reported to primarily increase ethanol formation in C. acetobutylicum. We found that overexpression of the AAD^D485G variant increased ethanol titers by 294%. Catalytic upgrading of the 824(aad^D485G) ABE products resulted in a blend with nearly 50 wt%≤C₉ products, which are unsuitable for diesel. To selectively increase butanol production, C. beijerinckii aldehyde dehydrogenase and C. ljungdhalii butanol dehydrogenase were co-expressed (strain designate 824(Cb ald-Cl bdh)), which increased butanol titers by 27% to 16.9 g L⁻¹ while acetone and ethanol titers remained essentially unaffected. The solvent ratio from 824(Cb ald-Cl bdh) resulted in more than 80 wt% of catalysis products having a carbon chain length≥C₁₁ which amounts to 9.8 g L⁻¹ of products suitable as kerosene or diesel blendstock based on fermentation volume. To further increase solvent production, we investigated expression of both native and heterologous chaperones in C. acetobutylicum. Expression of a heat shock protein (HSP33) from Bacillus psychrosaccharolyticus increased the total solvent titer by 22%. Co-expression of HSP33 and aldehyde/butanol dehydrogenases further increased ABE formation as well as acetone and butanol yields. HSP33 was identified as the first heterologous chaperone that significantly increases solvent titers above wild type C. acetobutylicum levels, which can be combined with metabolic engineering to further increase solvent production.     

Continuous butanol production with reduced byproducts formation from glycerol by a hyper producing mutant of <Emphasis Type="Italic">Clostridium pasteurianum</Emphasis>

Butanol, a four-carbon primary alcohol (C₄H₁₀O), is an important industrial chemical and has a good potential to be used as a superior biofuel. Bio-based production of butanol from renewable feedstock is a promising and sustainable alternative to substitute petroleum-based fuels. Here, we report the development of a process for butanol production from glycerol, which is abundantly available as a byproduct of biodiesel production. First, a hyper butanol producing strain of Clostridium pasteurianum was isolated by chemical mutagenesis. The best mutant strain, C. pasteurianum MBEL_GLY2, was able to produce 10.8 g l⁻¹ butanol from 80 g l⁻¹ glycerol as compared to 7.6 g l⁻¹ butanol produced by the parent strain. Next, the process parameters were optimized to maximize butanol production from glycerol. Under the optimized batch condition, the butanol concentration, yield, and productivity of 17.8 g l⁻¹, 0.30 g g⁻¹, and 0.43 g l⁻¹ h⁻¹ could be achieved. Finally, continuous fermentation of C. pasteurianum MBEL_GLY2 with cell recycling was carried out using glycerol as a major carbon source at several different dilution rates. The continuous fermentation was run for 710 h without strain degeneration. The acetone–butanol–ethanol productivity and the butanol productivity of 8.3 and 7.8 g l⁻¹ h⁻¹, respectively, could be achieved at the dilution rate of 0.9 h⁻¹. This study reports continuous production of butanol with reduced byproducts formation from glycerol using C. pasteurianum, and thus could help design a bioprocess for the improved production of butanol.     

Acetone–butanol–ethanol production with high productivity using Clostridium acetobutylicum BKM19

Conventional acetone–butanol–ethanol (ABE) fermentation is severely limited by low solvent titer and productivities. Thus, this study aims at developing an improved Clostridium acetobutylicum strain possessing enhanced ABE production capability followed by process optimization for high ABE productivity. Random mutagenesis of C. acetobutylicum PJC4BK was performed by screening cells on fluoroacetate plates to isolate a mutant strain, BKM19, which exhibited the total solvent production capability 30.5% higher than the parent strain. The BKM19 produced 32.5 g L^?1 of ABE (17.6 g L^?1 butanol, 10.5 g L^?1 ethanol, and 4.4 g L^?1 acetone) from 85.2 g L^?1 glucose in batch fermentation. A high cell density continuous ABE fermentation of the BKM19 in membrane cell‐recycle bioreactor was studied and optimized for improved solvent volumetric productivity. Different dilution rates were examined to find the optimal condition giving highest butanol and ABE productivities. The maximum butanol and ABE productivities of 9.6 and 20.0 g L^?1 h^?1, respectively, could be achieved at the dilution rate of 0.85 h^?1. Further cell recycling experiments were carried out with controlled cell‐bleeding at two different bleeding rates. The maximum solvent productivities were obtained when the fermenter was operated at a dilution rate of 0.86 h^?1 with the bleeding rate of 0.04 h^?1. Under the optimal operational condition, butanol and ABE could be produced with the volumetric productivities of 10.7 and 21.1 g L^?1 h^?1, and the yields of 0.17 and 0.34 g g^?1, respectively. The obtained butanol and ABE volumetric productivities are the highest reported productivities obtained from all known‐processes. Biotechnol. Bioeng. 2013; 110: 1646–1653. © 2013 Wiley Periodicals, Inc.     

Production of acetone butanol (AB) from liquefied corn starch,a commercial substrate,using <Emphasis Type="Italic">Clostridium beijerinckii</Emphasis> coupled with product recovery by gas stripping

A potential industrial substrate (liquefied corn starch; LCS) has been employed for successful acetone butanol ethanol (ABE) production. Fermentation of LCS (60 g l⁻¹) in a batch process resulted in the production of 18.4 g l⁻¹ ABE, comparable to glucose: yeast extract based medium (control experiment, 18.6 g l⁻¹ ABE). A batch fermentation of LCS integrated with product recovery resulted in 92% utilization of sugars present in the feed. When ABE was recovered by gas stripping (to relieve inhibition) from the fed-batch reactor fed with saccharified liquefied cornstarch (SLCS), 81.3 g l⁻¹ ABE was produced compared to 18.6 g l⁻¹ (control). In this integrated system, 225.8 g l⁻¹ SLCS sugar (487 % of control) was consumed. In the absence of product removal, it is not possible for C. beijerinckii BA101 to utilize more than 46 g l⁻¹ glucose. A combination of fermentation of this novel substrate (LCS) to butanol together with product recovery by gas stripping may economically benefit this fermentation. Mention of trade names of commercial products in this article/publication is solely for the purpose of providing scientific information and does not imply recommendation or endorsement by the United States Department of Agriculture.     

High solid fed‐batch butanol fermentation with simultaneous product recovery: Part II—process integration

In these studies, liquid hot water (LHW) pretreated and enzymatically hydrolyzed Sweet Sorghum Bagasse (SSB) hydrolyzates were fermented in a fed‐batch reactor. As reported in the preceding paper, the culture was not able to ferment the hydrolyzate I in a batch process due to presence of high level of toxic chemicals, in particular acetic acid released from SSB during the hydrolytic process. To be able to ferment the hydrolyzate I obtained from 250 g L^?1 SSB hydrolysis, a fed‐batch reactor with in situ butanol recovery was devised. The process was started with the hydrolyzate II and when good cell growth and vigorous fermentation were observed, the hydrolyzate I was slowly fed to the reactor. In this manner the culture was able to ferment all the sugars present in both the hydrolyzates to acetone butanol ethanol (ABE). In a control batch reactor in which ABE was produced from glucose, ABE productivity and yield of 0.42 g L^?1 h^?1 and 0.36 were obtained, respectively. In the fed‐batch reactor fed with SSB hydrolyzates, these productivity and yield values were 0.44 g L^?1 h^?1 and 0.45, respectively. ABE yield in the integrated system was high due to utilization of acetic acid to convert to ABE. In summary we were able to utilize both the hydrolyzates obtained from LHW pretreated and enzymatically hydrolyzed SSB (250 g L^?1) and convert them to ABE. Complete fermentation was possible due to simultaneous recovery of ABE by vacuum. © 2018 American Institute of Chemical Engineers Biotechnol. Prog., 34:967–972, 2018     

ABE production from corn: a recent economic evaluation

This article details an economic assessment of butanol production from corn using the newly developed hyper-butanol-producing strain of Clostridium beijerinckii BA101. Butanol is produced in batch reactors and recovered by distillation. For a plant with 153,000 metric tons of acetone, butanol, and ethanol (ABE) production capacity, the production equipment cost and total working capital cost is US$33.47×10⁶ and US$110.46×10⁶, respectively. Based on a corn price (C _p) of US$79.23 ton⁻¹ (US$2.01 bushel⁻¹), an ABE yield of 0.42 (g ABE/g glucose) butanol price is projected to be US$0.34 kg⁻¹. An improved yield of 0.50 will reduce this price to US$0.29 kg⁻¹. Assumptions, such as by-product credit for gases and complete conversion of corn steep liquor (CSL) to fermentation by-products, have been taken into consideration. An increased price of corn to US$197.10 ton⁻¹ would result in a butanol price of US$0.47 kg⁻¹. A grass-rooted plant would result in a butanol price of US$0.73 kg⁻¹ (C _p US$79.23 ton⁻¹). In a worst case scenario, the price of butanol would increase to US$1.07 kg⁻¹ (C _p 197.10 ton⁻¹ for a grass-rooted plant and assuming no credit for gases). This is based on the assumption that corn price would not increase to more than US$197.10 ton⁻¹. Journal of Industrial Microbiology & Biotechnology (2001) 27, 292–297. Received 12 September 2000/ Accepted in revised form 12 January 2001     

Soy molasses as fermentation substrate for production of butanol using Clostridium beijerinckii BA101

Spray-dried soy molasses (SDSM) contains the sugars dextrose, sucrose, fructose, pinitol, raffinose, verbascose, melibiose, and stachyose. Of the 746 g kg⁻¹ total sugars in SDSM, 434 g kg⁻¹ is fermentable using Clostridium beijerinckii BA101. SDSM was used to produce acetone, butanol, and ethanol (ABE) by C. beijerinckii BA101 in batch cultures. Using 80 g l⁻¹ SDSM, 10.7 g l⁻¹ ABE was produced in P2 medium. Higher concentrations of SDSM resulted in poor solvent production due to the presence of excessive salt and inhibitory components. C. beijerinckii BA101 in SDSM at 80 g l⁻¹ concentration produced 22.8 g l⁻¹ ABE when supplemented with 25.3 g l⁻¹ glucose. SDSM contains 57.4 g kg⁻¹ mineral ash and 2% tri-calcium phosphate. Tri-calcium phosphate up to 43.1 g l⁻¹ was not inhibitory and at a tri-calcium phosphate concentration of 28.8 g l⁻¹, the culture produced more solvents (30.1 g l⁻¹) than the control experiment (23.8 g l⁻¹). In contrast, sodium chloride was a strong inhibitor of C. beijerinckii BA101 cell growth. At a concentration of 10 g l⁻¹ sodium chloride, a maximum cell concentration of 0.6 g l⁻¹ was achieved compared to 1.7 g l⁻¹ in the control experiment. The effects of two salts on specific growth rate constant (μ) and specific rate of ABE production (ν) for C. beijerinckii BA101 were examined. Journal of Industrial Microbiology & Biotechnology (2001) 26, 290–295. Received 20 September 2000/ Accepted in revised form 16 February 2001     

Improving performance of a gas stripping-based recovery system to remove butanol from Clostridium beijerinckii fermentation

The effect of factors such as gas recycle rate, bubble size, presence of acetone, and ethanol in the solution/broth were investigated in order to remove butanol from model solution or fermentation broth (also called acetone butanol ethanol or ABE or solvents). Butanol (8 g L^–1, model solution, Fig. 2) stripping rate was found to be proportional to the gas recycle rate. In the bubble size range attempted (<0.5 and 0.5–5.0 mm), the bubble size did not have any effect on butanol removal rate (Fig. 3, model solution). In Clostridium beijerinckii fermentation, ABE productivity was reduced from 0.47 g L^–1 h^–1 to 0.25 g L^–1 h^–1 when smaller (<0.5 mm) bubble size was used to remove ABE (Fig. 4, results reported as butanol/ABE concentration). The productivity was reduced as a result of addition of an excessive amount of antifoam used to inhibit the production of foam caused by the smaller bubbles. This suggested that the fermentation was negatively affected by antifoam.Mention of trade names of commercial products in this article is solely for the purpose of providing scientific information and does not imply recommendation or endorsement by the United States Department of Agriculture.     

<Emphasis Type="Italic">Clostridium beijerinckii</Emphasis> mutant with high inhibitor tolerance obtained by low-energy ion implantation

Clostridium beijerinckii mutant strain IB4, which has a high level of inhibitor tolerance, was screened by low-energy ion implantation and used for butanol fermentation from a non-detoxified hemicellulosic hydrolysate of corn fiber treated with dilute sulfuric acid (SAHHC). Evaluation of toxicity showed C. beijerinckii IB4 had a higher level of tolerance than parent strain C. beijerinckii NCIMB 8052 for five out of six phenolic compounds tested (the exception was vanillin). Using glucose as carbon source, C. beijerinckii IB4 produced 9.1 g l⁻¹ of butanol with an acetone/butanol/ethanol (ABE) yield of 0.41 g g⁻¹. When non-detoxified SAHHC was used as carbon source, C. beijerinckii NCIMB 8052 grew well but ABE production was inhibited. By contrast, C. beijerinckii IB4 produced 9.5 g l⁻¹ of ABE with a yield of 0.34 g g⁻¹, including 2.2 g l⁻¹ acetone, 6.8 g l⁻¹ butanol, and 0.5 g l⁻¹ ethanol. The remarkable fermentation and inhibitor tolerance of C. beijerinckii IB4 appears promising for ABE production from lignocellulosic materials.     

CaCO<Subscript>3</Subscript> supplementation alleviates the inhibition of formic acid on acetone/butanol/ethanol fermentation by <Emphasis Type="Italic">Clostridium acetobutylicum</Emphasis>

Objective

To investigate the inhibiting effect of formic acid on acetone/butanol/ethanol (ABE) fermentation and explain the mechanism of the alleviation in the inhibiting effect under CaCO₃ supplementation condition.

Results

From the medium containing 50 g sugars l^?1 and 0.5 g formic acid l^?1, only 0.75 g ABE l^?1 was produced when pH was adjusted by KOH and fermentation ended prematurely before the transformation from acidogenesis to solventogenesis. In contrast, 11.4 g ABE l^?1 was produced when pH was adjusted by 4 g CaCO₃ l^?1. The beneficial effect can be ascribed to the buffering capacity of CaCO₃. Comparative analysis results showed that the undissociated formic acid concentration and acid production coupled with ATP and NADH was affected by the pH buffering capacity of CaCO₃. Four millimole undissociated formic acid was the threshold at which the transformation to solventogenesis occurred.

Conclusion

The inhibiting effect of formic acid on ABE fermentation can be alleviated by CaCO₃ supplementation due to its buffering capacity.

     

Production of butanol from starch-based waste packing peanuts and agricultural waste

We examined the fermentation of starch-based packing peanuts and agricultural wastes as a source of fermentable carbohydrates using Clostridium beijerinckii BA101. Using semidefined P2 medium containing packing peanuts and agricultural wastes, instead of glucose as a carbohydrate source, we measured characteristics of the fermentation including solvent production, productivity, and yield. With starch as substrate (control), the culture produced 24.7 g l⁻¹ acetone–butanol–ethanol (ABE), while with packing peanuts it produced 21.7 g l⁻¹ total ABE with a productivity of 0.20 g l⁻¹ h⁻¹ and a solvent (ABE) yield of 0.37. Cell growth in starch, packing peanuts, and agricultural wastes medium was different, possibly due to the different nature of these substrates. Using model agricultural waste, 20.3g l⁻¹ ABE was produced; when using actual waste, 14.8 g l⁻¹ ABE was produced. The use of inexpensive substrates will increase the economic viability of the conversion of biomass to butanol, and can provide new markets for these waste streams. Journal of Industrial Microbiology & Biotechnology (2002) 29, 117–123 doi: 10.1038/sj.jim.7000285 Received 14 November 2001/ Accepted in revised form 07 June 2002     

Genetically engineered Escherichia coli FBR5: Part I. Comparison of high cell density bioreactors for enhanced ethanol production from xylose

Five reactor systems (free cell batch, free cell continuous, entrapped cell immobilized, adsorbed cell packed bed, and cell recycle membrane reactors) were compared for ethanol production from xylose using Escherichia coli FBR5. In the free cell batch and free cell continuous reactors (continuous stirred tank reactor‐CSTR) productivities of 0.84 gL^?1 h^?1 and 1.77 gL^?1 h^?1 were achieved, respectively. A cell recycle membrane reactor resulted in the highest productivity of 55.56 gL^?1 h^?1, which is an increase of 66‐fold (e.g., 6614%) over the batch reactor. Calcium alginate gel CSTR resulted in a productivity of 2.04 gL^?1 h^?1 whereas adsorbed cell packed bed reactor resulted in a productivity of 4.39 gL^?1 h^?1. In the five reactor systems, ethanol concentrations ranged from 18.9 to 40.30 gL^?1 with metabolic yields from 0.44 to 0.51. Published 2012 American Institute of Chemical Engineers Biotechnol. Prog., 2012     

Microbial production of a biofuel (acetone–butanol–ethanol) in a continuous bioreactor: impact of bleed and simultaneous product removal

Acetone butanol ethanol (ABE) was produced in an integrated continuous one-stage fermentation and gas stripping product recovery system using Clostridium beijerinckii BA101 and fermentation gases (CO₂ and H₂). In this system, the bioreactor was fed with a concentrated sugar solution (250–500 g L^?1 glucose). The bioreactor was bled semi-continuously to avoid accumulation of inhibitory chemicals and products. The continuous system was operated for 504 h (21 days) after which the fermentation was intentionally terminated. The bioreactor produced 461.3 g ABE from 1,125.0 g total sugar in 1 L culture volume as compared to a control batch process in which 18.4 g ABE was produced from 47.3 g sugar. These results demonstrate that ABE fermentation can be operated in an integrated continuous one-stage fermentation and product recovery system for a long period of time, if butanol and other microbial metabolites in the bioreactor are kept below threshold of toxicity.