Organosolv pulping of wheat straw by use of phenol

A central composite design was used to investigate the influence of the cooking conditions (time, temperature and phenol concentration) for wheat straw with phenol-water mixtures on the properties of the pulp obtained (yield and holocellulose, -cellulose, lignin and ethanol-benzene extractable contents) and the pH of the resulting wastewater. A second-order polynomial model consisting of three independent process variables was found to accurately describe the organosolv pulping of wheat straw. The equations derived predict the yield, the holocellulose, -cellulose, lignin and ethanol-benzene extractable contents of the pulp, and the pH of the wastewater with multiple-R, R² and adjusted-R² high values. The process variables must be set at low variables in order to ensure a high yield and pH. Conversely, if high holocellulose and -cellulose contents, and low lignin and ethanol-benzene extractable contents are desired, then a high temperature (200°C), long cooking time (120 min), and intermediate phenol concentration (65%) must be used.     

Influence of dimethyl formamide pulping of bagasse on pulp properties

Organosolv pulping of bagasse was conducted following a central composite design using a two-level factorial plan involving three pulping variables (temperature: 190-210 degrees C, time: 120-180 min, organic solvent charge: 40-60% dimethyl formamide). Responses of pulp properties (yield and holocellulose, alpha-cellulose, kappa number, ash and ethanol-dichloromethane extractives contents) and the pH of the resulting wastewater to the process variables were analyzed using statistical software (MINITAB). Main factor analysis revealed that optimum pulp has the following characteristics: 82.7% (yield), 92.9 (kappa number), 95.84% (holocellulose), 83.53% (alpha-cellulose), 1.403% (ash), 2.562% (ethanol-dichloromethane extractives contents) and 6.39 (pH). These results showed that acceptable properties of pulps could be gained at 200-210 degrees C for 150 min and 40-60% DMF. Based on these results, this method could be used for pulping of bagasse equivalent NSSC concerning high yield at a fixed kappa number. In addition, bagasse could be pulped with ease to approximately 55% yield with a kappa number approximately 31. Numerical analyses showed that cooking temperature had the greatest influence on properties of obtained pulps within the DMF concentrations and cooking time as cooking variables.     

Pulping of holm oak wood. Influence of the operating conditions

This paper reports on the influence of independent variables in the pulping of holm oak wood (Quercus ilex L.) [viz. temperature (135-195 degrees C), cooking time (30-90min) and soda concentration (10-20%)] on the yield, holocellulose content, alpha-cellulose content, brightness and viscosity of the resulting pulp. By using a central composite factorial design, equations relating each dependent variable to the different independent variables were derived that reproduced the experimental results for the dependent variables with errors less than 5-15% in all cases. The highest pulp yield (56.9%) was obtained with the lowest values of the operating variables. However, obtaining the optimum holocellulose content, alpha-cellulose content and viscosity (viz. 94.5%, 78.5% and 1395ml/g, respectively) entailed using values of the independent variables above their mean levels. Also, ensuring optimal brightness (viz. 24.3%) required using higher temperatures and soda concentrations. A compromise that saves equipment immobilized capital and about 25% of soda is using a soda concentration of 15% at 195 degrees C for 30min. The yield thus obtained differs by less than 29.5% from the highest level; also, the resulting holocellulose content, alpha-cellulose content and brightness differ by less than 12% from their respective optimum values.     

Effect of organosolv and soda pulping processes on the metals content of non-woody pulps

In this work the effect of different pulping processes (ethyleneglycol, diethyleneglycol, ethanolamine and soda) of tow abounded raw materials (empty fruit bunches - EFB and rice straw) on the ash, silicates and metals (Fe, Zn, Cu, Pb, Mn, Ni and Cd) content of the obtained pulps have been studied. Results showed that pulps obtained by diethyleneglycol pulping process presented lower metals content (756 microg/g and 501 microg/g for EFB and rice straw pulp, respectively) than soda pulps (984 microg/g and 889 microg/g). Ethanolamine pulps presented values of holocellulose (74% and 77% for EFB and rice straw pulp, respectively), alpha-cellulose (74% and 69%), kappa number (18.7 and 18.5) and viscosity (612 and 90 6ml/g) similar to those of soda pulp, and lower lignin contents (11% and 12%).     

Hydrothermal and pulp processing of Eucalyptus

Hydrothermal processing of Eucalyptus wood was performed at operation temperature of 181 degrees C, processing time or 37.5 min and solid water ratio of 1/6 to ensure a maximum loss of xylan recuperation with minimum cellulose fibre degradation. Under those conditions, the loss of xylan was 22% less than that achieved with the conditions 196 degrees C, 50.6 min and 1/8 (solid/water). IN In addition, an experimental design was used to study the influence of process variables: temperature (145-175 degrees C), pulping time (40-120 min) and ethanol concentration (40-70% weight concentration), on the properties of pulps (yield, kappa number, viscosity, cellulose, xylan, lignin acetyl groups contents and brightness) and paper sheets (stretch index, burst index and tear index) obtained from the solid fraction after hydrothermal treatment of Eucalyptus globulus. Pulps with acceptably high physical and chemical properties can be obtained operating at 175 degrees C for 90 min with 55% ethanol concentration.     

New perspectives for Paulownia fortunei L. valorisation of the autohydrolysis and pulping processes

This paper will consider the influence of the temperature of autohydrolysis or hydrothermal process from Paulownia fortunei L. to obtain a valuable liquid phase and a suitable solid phase to produce pulp. The solid phase resulting of autohydrolysis was subjected to organosolv pulping process and formed paper sheets, analyzing the influence of operational variables (viz., ethanol concentration, temperature and pulping time) on the yield, viscosity, tensile index, burst index, tear index and brightness. Maximum glucose and xylose contents and minimum paper sheets characteristic loss have been obtained at 190 degrees C authohydrolysis temperature. Suitable characteristics of paper sheets and acceptable yield, viscosity and kappa number of pulp could be obtained by operating at 180 degrees C temperature, 30min pulping time and 20% ethanol concentration. Under those conditions sheets paper with 27.4% ISO brightness, 28.87Nm/g tensile index, 1.22kPam(2)/g burst index and 1.23kNm(2)/g tear index could be obtained.     

Ethanol-acetone pulping of wheat straw. Influence of the cooking and the beating of the pulps on the properties of the resulting paper sheets

The influence of independent variables in the pulping of wheat straw by use of an ethanol-acetone-water mixture [processing temperature and time, ethanol/(ethanol + acetone) value and (ethanol + acetone)/(ethanol + acetone + water) value] and of the number of PFI beating revolutions to which the pulp was subjected, on the properties of the resulting pulp (yield and Shopper-Riegler index) and of the paper sheets obtained from it (breaking length, stretch, burst index and tear index) was examined. By using a central composite factor design and the BMDP software suite, equations that relate each dependent variable to the different independent variables were obtained that reproduced the experimental results for the dependent variables with errors less than 30% at temperatures, times, ethanol/(ethanol + acetone) value, (ethanol + acetone)/(ethanol + acetone + water) value and numbers of PFI beating revolutions in the ranges 140-180 degrees C, 60-120 min, 25-75%, 35-75% and 0-1750, respectively. Using values of the independent variables over the variation ranges considered provided the following optimum values of the dependent variables: 78.17% (yield), 15.21 degrees SR (Shopper-Riegler index), 5265 m (breaking length), 1.94% (stretch), 2.53 kN/g (burst index) and 4.26 mN m2/g (tear index). Obtaining reasonably good paper sheets (with properties that differed by less than 15% from their optimum values except for the burst index, which was 28% lower) entailed using a temperature of 180 degrees C, an ethanol/(ethanol + acetone) value of 50%, an (ethanol + acetone)/(ethanol + acetone + water) value of 75%, a processing time of 60 min and a number of PFI beating revolutions of 1750. The yield was 32% lower under these conditions, however. A comparison of the results provided by ethanol, acetone and ethanol-acetone pulping revealed that the second and third process-which provided an increased yield were the best choices. On the other hand, if the pulp is to be refined, ethanol pulping is the process of choice.     

Optimization of pulping conditions of abaca. An alternative raw material for producing cellulose pulp

The influence of temperature (150-170 degrees C), pulping time (15-45 min) and soda concentration (5-10%) in the pulping of abaca on the yield, kappa, viscosity, breaking length, stretch and tear index of pulp and paper sheets, was studied. Using a factorial design to identify the optimum operating conditions, equations relating the dependent variables to the operational variables of the pulping process were derived that reproduced the former with errors lower than 25%. Using a high temperature, and a medium time and soda concentration, led to pulp that was difficult to bleach (kappa 28.34) but provided acceptable strength-related properties (breaking length 4728 m; stretch 4.76%; tear index 18.25 mN m2/g), with good yield (77.33%) and potential savings on capital equipment costs. Obtaining pulp amenable to bleaching would entail using more drastic conditions than those employed in this work.     

Hydrothermal treatment and ethanol pulping of sunflower stalks

The influence of temperature in the hydrothermal treatment of sunflower stalks on the composition of the liquid fraction obtained was examined. The remaining solid fraction was subjected to ethanol pulping in order to obtain pulp that was used to produce paper sheets. The pulp was characterized in terms of yield, kappa index, viscosity, and cellulose, hemicellulose and lignin contents; and the paper sheets in terms of breaking length, stretch, burst index and tear index. Hydrothermal treatment of the raw material at 190 degrees C provided a liquid phase with maximal hemicellulose-derived oligomers and monosaccharide (glucose, xylose and arabinose) contents (26.9 and 4.2 g/L, respectively). Pulping the solid fraction obtained by hydrothermal treatment at 180 degrees C, with 70% ethanol at a liquid/solid ratio of 8:1 at 170 degrees C for 120 min provided pulp with properties on a par with those of soda pulp from the sunflower stalks, namely: 36.3% yield, 69.1% cellulose, 12.6% hemicellulose, 18.2% lignin and 551 ml/g viscosity. Also, paper sheets obtained from the ethanol pulp were similar in breaking length (3.8 km), stretch (1.23%), burst index (1.15 kN/g) and tear index (2.04 m Nm(2)/g) to those provided by soda pulp.     

Characterization of vine shoots, cotton stalks, Leucaena leucocephala and Chamaecytisus proliferus, and of their ethyleneglycol pulps

We characterized vine shoots, cotton stalks, Leucaena leucocephala and Chamaecytisus proliferus as pulping raw materials and found C. proliferus and cotton stalks to be the best for the intended purpose on the grounds of their increased contents in holocellulose (79.73% and 72.86%) and alpha-cellulose (45.37% and 58.48%), and their decreased contents in ethanol-benzene extractables (2.64% and 1.42%), hot water solubles (2.79% and 3.33%) and 1% soda solubles (16.67% and 20.34%). These properties resulted in increased pulp yields and hence in efficient use of these two types of raw material. The previous raw materials were pulped by using an ethyleneglycol concentration of 65% at 180 degrees C for 75min, followed by beating at 1500 revolutions in a PFI refiner. The paper sheets obtained were characterized and those from C. proliferus found to be the best overall as they exhibited an increased breaking length (4644m), stretch (2.87%), burst index (2.46kN/g) tear index (0.33mNm(2)/g) and brightness (49.92% ISO); in addition C. proliferus pulp was obtained with a high-yield (62.88%). On the other hand, vine shoots provided the poorest results among the studied raw materials.     

Ethyleneglycol pulp from tagasaste

In this work, we examined the influence of operational variables [viz. Ethyleneglycol concentration (50-70%), temperature (155-185 degrees C), time (30-90 min) and number of PFI beating revolutions (500-1500)] in the ethyleneglycol pulping of tagasaste (Chamaecytisus proliferus) on pulp yield and the breaking length, stretch, burst index, tear index and brightness of paper sheets formed from it. Application of a fuzzy neural network model in combination with an experimental factorial design allowed the results for the dependent variables to be predicted as a function of the operating conditions used with errors less than 15% in all cases. The operating conditions of choice provided pulp with a high yield (56.85%) and a low brightness (22.51%) which may thus be useful to obtain non-white paper.     

Influence of the holm oak soda pulping conditions on the properties of the resulting paper sheets

This paper reports on the influence of independent variables in the pulping of holm oak wood [viz. temperature (135-195 degrees C), cooking time (30-90 min) and soda concentration (10-20%)] on the properties of the resulting paper sheets. By using a central composite factorial design and a fuzzy neural model, equations relating each dependent variable to the different independent variables were derived that reproduced the experimental results for the dependent variables with errors less than 14%. Using a soda concentration of 17.5% at 195 degrees C for 30 min, it is possible to reduce the working capital (cost of chemical) and the capital investment, because it is operated with smaller values of the soda concentration and cooking time that maximum considered (20% of soda concentration and 90 min). The pulp yield thus obtained differed by less than 31.3% from the highest possible value; also, the resulting pulp and paper sheets had acceptable properties that differed by less than 21.10% from their optimum values.     

Wavelet neural networks applied to pulping of oil palm fronds

In the organosolv pulping of the oil palm fronds, the influence of the operational variables of the pulping reactor (viz. cooking temperature and time, ethanol and NaOH concentration) on the properties of the resulting pulp (yield and kappa number) and paper sheets (tensile index and tear index) was investigated using a wavelet neural network model. The experimental results with error less than 0.0965 (in terms of MSE) were produced, and were then compared with those obtained from the response surface methodology. Performance assessment indicated that the neural network model possessed superior predictive ability than the polynomial model, since a very close agreement between the experimental and the predicted values was obtained.     

Comparison of polynomial and neural fuzzy models as applied to the ethanolamine pulping of vine shoots

The influence of operational variables in the pulping of vine shoots by use of ethanolamine [viz. temperature (155-185 degrees C), cooking time (30-90min) and ethanolamine concentration (50-70% v/v)] on the properties of the resulting pulp (viz. yield, kappa index, viscosity and drainability) was studied. A central composite factorial design was used in conjunction with the software BMDP and ANFIS Edit Matlab 6.5 to develop polynomial and fuzzy neural models that reproduced the experimental results of the dependent variables with errors less than 10%. Both types of models are therefore effective with a view to simulating the ethanolamine pulping process. Based on the proposed equations, the best choice is to use values of the operational valuables resulting in near-optimal pulp properties while saving energy and immobilized capital on industrial facilities by using lower temperatures and shorter processing times. One combination leading to near-optimal properties with reduced costs is using a temperature of 180 degrees C and an ethanolamine concentration of 60% for 60min, to obtain pulp with a viscosity of 6.13% lower than the maximum value (932.8ml/g) and a drainability of 5.49% lower than the maximum value (71 (o)SR).     

Pulp and paper from vine shoots: neural fuzzy modeling of ethylene glycol pulping

The influence of operational variables in the pulping of vine shoots by use of ethylene glycol [viz. temperature (155-185 degrees C), cooking time (30-90 min) and ethylene glycol concentration (50-70% v/v)] on the properties of the resulting pulp (viz. yield, kappa number and viscosity) and paper sheets (breaking length, stretch, burst index, tear index and brightness) was studied. A central composite factorial design was used in conjunction with the software ANFIS Edit Matlab 6.5 to develop fuzzy neural model that reproduced the experimental results of the dependent variables with errors less than 5%. The model is therefore effective with a view to simulating the ethylene glycol pulping process.     

Influence of dimethyl formamide pulping of wheat straw on cellulose degradation and comparison with Kraft process

The pulping of wheat straw with dimethyl formamide was studied in order to investigate the effects of the cooking variables (temperature (190 degrees C, 200 degrees C, and 210 degrees C) and time (120 min, 150 min, and 180 min) and organic solvent ratio (30%, 50%, and 70%) dimethyl formamide (DMF+water) value) on the degradation of cellulose and degree of polymerization (DP) of organosolv pulp. The SCAN viscosity was applied to estimating the extent of cellulose degradation produced by cooking condition and then, it was compared with Kraft pulp at equal Kappa number. Response of pulp and handsheets properties to the process variables were analyzed using statistical software (MINITAB 14). The process variables (cooking temperature and cooking time) must be set at low variables with high DMF ratio in order to ensure a high yield and high SCAN viscosity. Also, pulps with high mechanical properties can be acceptably obtained at 210 degrees C for 150 min with 50% DMF. Generally, the cooking temperature was a significant factor while the cooking time and DMF ratio had a smaller role. By the comparison of Kraft and organosolv pulp, it can be resulted that DMF basically had improvement role on reducing of cellulose degradation by reason of high SCAN viscosity of organosolv pulp than Kraft pulp under equal kappa number and, scanning electron microscopy (SEM) of obtained pulp. Consequently, the protective action of organic solvent on non-cellulosic polysaccharides of wheat straw against degradation under Kraft pulping conditions was pointed as a main reason of the fairly high yield of organosolv pulps.     

Influence of rice straw cooking conditions in the soda-ethanol-water pulping on the mechanical properties of produced paper sheets

A normalized design was used to examine the influence of independent variables (alcohol concentration, cooking time and temperature) in the catalytic soda-ethanol pulping of rice straw on various mechanical properties (breaking length, burst, tear index and folding endurance) of paper sheets obtained from each pulping process. An equation of each dependent variable as a function of cooking variables (independent variables) was obtained by multiple non-linear regression using the least square method by MATLAB software for developing of empirical models. The ranges of alcohol concentration, cooking time and temperature were 40-65% (w/w), 150-180 min and 195-210 degrees C, respectively. Three-dimensional graphs of dependent variables were also plotted versus independent variables. The optimum values of breaking length, burst and tear index and folding endurance were 4683.7 (m), 30.99 (kN/g), 376.93 (mN m2/g) and 27.31, respectively. However, short cooking time (150 min), high ethanol concentration (65%) and high temperature (210 degrees C) could be used to produce papers with suitable burst and tear index. However, for papers with best breaking length and folding endurance low temperature (195 degrees C) was desirable. Differences between optimum values of dependent variables obtained by normalized design and experimental data were less than 20%.     

Eucalyptus globulus wood fractionation by autohydrolysis and organosolv delignification

This work provides an assessment on the fractionation of Eucalyptus globulus wood by sequential stages of autohydrolysis (to cause the solubilization of hemicelluloses) and organosolv pulping (to dissolve lignin, leaving solids enriched in cellulose). With this approach, valuable products (hemicellulose-derived saccharides, sulphur-free lignin fragments and cellulosic substrates with low contents of residual hemicelluloses) are obtained in separate streams, according to the biomass refinery approach. Autohydrolysis was carried out under optimized operational conditions, and organosolv pulping was performed using uncatalyzed ethanol-water solutions. The effects of the most influential operational variables (autohydrolysis severity, delignification temperature and ethanol concentration in the organosolv stage) on solid yield, solid composition, cellulose susceptibility and recovery of the various fractions was assessed using statistical methods, which enabled the identification of the most favourable operational conditions.     

Use of high-boiling point organic solvents for pulping oil palm empty fruit bunches

Oil palm empty fruit bunches were used as an alternative raw material to obtain cellulosic pulp. Pulping was done by using high-boiling point organic solvents of decreased polluting power relative to classical (Kraft, sulphite) solvents but affording operation at similar pressure levels. The holocellulose, alpha-cellulose and lignin contents of oil palm empty fruit bunches (viz. 66.97%, 47.91% and 24.45%, respectively) are similar to those of some woody raw materials such as pine and eucalyptus, and various non-wood materials including olive tree prunings, wheat straw and sunflower stalks. Pulping tests were conducted by using ethyleneglycol, diethyleneglycol, ethanolamine and diethanolamine under two different sets of operating conditions, namely: (a) a 70% solvent concentration, 170 degrees C and 90 min; and (b) 80% solvent, 180 degrees C and 150 min. The solid/liquid ratio was six in both cases. The amine solvents were found to provide pulp with better properties than did the glycol solvents. Ethanolamine pulp exhibited the best viscosity and drainage index (viz. 636 mL/g and 17 degrees SR, respectively), and paper made from it the best breaking length (1709 m), stretch (1.95%), burst index (0.98 kN/g) and tear index (0.33 mNm(2)/g). Operating costs can be reduced by using milder conditions, which provide similar results. In any case, the amines are to be preferred to the glycols as solvents for this purpose.     

Milox fractionation of empty fruit bunches from Elaeis guineensis

Milox pulping of EFB was used to obtain pulps. In the first Milox stage, the influences of operating variables on pulp properties were studied and polynomial and neural fuzzy models that reproduced the experimental results with errors less than 10% were developed. Operating variables were found (93 wt.% of formic acid, 3 wt.% of hydrogen peroxide, and 165 min) that yielded acceptable pulp properties (40.5% yield, 50.3% brightness and 608 mL/g viscosity) at reasonable chemical and energy costs. The second stage was studied by subjecting the liquors of the previously optimized first stage to different treatment times. This time should be 30 min or less, to avoid a negative effect on viscosity. The residual liquor from the first Milox stage contained virtually no precipitable lignin and only low amounts of sugar (wt.%): glucose 0.71, xylose 4.22, galactose 1.19, mannose 0.22, all on original raw material dry.