Fabrication of Efficient and Stable CsPbI3 Perovskite Solar Cells through Cation Exchange Process

Inorganic lead halide perovskites have attracted attention due to their tolerance to higher processing temperature and higher bandgap suitable for tandem solar cell application. Not only do they improve cell stability and efficiency, they also reveal many interesting and un‐anticipated material qualities. This work reports a simple cation exchange growth (CEG) method for fabricating inorganic high‐quality cesium lead iodide (CsPbI₃) by adding methylammonium iodide (MAI) additive in the precursor. X‐ray diffraction results reveal a multi‐stage film formation process whereby i) MAPbI₃ perovskite first formed that acts as a perovskite template for ii) subsequent ion exchange whereby the MA⁺ ions in the MAPbI₃ are replaced by Cs⁺ (as temperature ramps up) and iii) form g‐phase perovskite CsPbI₃. Optical microscopy, photoluminescence, and electrical characterizations reveal that the CEG process produces high‐quality film with better absorption, uniform and dense film with better interface, lower defects, and better stability. Using the CEG approach, the power conversion efficiency of the best CsPbI₃ solar cell is significantly increased up to 14.1% for the device fabricated using 1.0 m MAI additive. The outcome is beneficial for further improvement of inorganic perovskite solar cells and their application in perovskite‐silicon tandem devices.     

Precursor Engineering for Ambient‐Compatible Antisolvent‐Free Fabrication of High‐Efficiency CsPbI2Br Perovskite Solar Cells

High temperature stable inorganic CsPbX₃ (X: I, Br, or mixed halides) perovskites with their bandgap tailored by tuning the halide composition offer promising opportunities in the design of ideal top cells for high‐efficiency tandem solar cells. Unfortunately, the current high‐efficiency CsPbX₃ perovskite solar cells (PSCs) are prepared in vacuum, a moisture‐free glovebox or other low‐humidity conditions due to their poor moisture stability. Herein, a new precursor system (HCOOCs, HPbI₃, and HPbBr₃) is developed to replace the traditional precursors (CsI, PbI₂, and PbBr₂) commonly used for solar cells of this type. Both the experiments and calculations reveal that a new complex (HCOOH?Cs⁺) is generated in this precursor system. The new complex is not only stable against aging in humid air ambient at 91% relative humidity, but also effectively slows the perovskite crystallization, making it possible to eliminate the popular antisolvent used in the perovskite CsPbI₂Br film deposition. The CsPbI₂Br PSCs based on the new precursor system achieve a champion efficiency of 16.14%, the highest for inorganic PSCs prepared in ambient air conditions. Meanwhile, high air stability is demonstrated for an unencapsulated CsPbI₂Br PSC with 92% of the original efficiency remaining after more than 800 h aging in ambient air.     

High‐Efficiency CsPbI2Br Perovskite Solar Cells with Dopant‐Free Poly(3‐hexylthiophene) Hole Transporting Layers

CsPbI₂Br is emerging as a promising all‐inorganic material for perovskite solar cells (PSCs) due to its more stable lattice structure and moisture resistance compared to CsPbI₃, although its device performance is still much behind this counterpart. Herein, a preannealing process is developed and systematically investigated to achieve high‐quality CsPbI₂Br films by regulating the nucleation and crystallization of perovskite. The preannealing temperature and time are specifically optimized for a dopant‐free poly(3‐hexylthiophene) (P3HT)‐based device to target dopant‐induced drastic performance degradation for spiro‐OMeTAD‐based devices. The resulting P3HT‐based device exhibits comparable power conversion efficiency (PCE) to spiro‐OMeTAD‐based devices but much enhanced ambient stability with over 95% PCE after 1300 h. A diphenylamine derivative is introduced as a buffer layer to improve the energy‐level mismatch between CsPbI₂Br and P3HT. A record‐high PCE of 15.50% for dopant‐free P3HT‐based CsPbI₂Br PSCs is achieved by alleviating the open‐circuit voltage loss with the buffer layer. These results demonstrate that the preannealing processing together with a suitable buffer layer are applicable strategies for developing dopant‐free P3HT PSCs with high efficiency and stability.     

Low Temperature Synthesis of Stable γ‐CsPbI3 Perovskite Layers for Solar Cells Obtained by High Throughput Experimentation

The structural phases and optoelectronic properties of coevaporated CsPbI₃ thin films with a wide range of [CsI]/[PbI₂] compositional ratios are investigated using high throughput experimentation and gradient samples. It is found that for CsI‐rich growth conditions, CsPbI₃ can be synthesized directly at low temperature into the distorted perovskite γ‐CsPbI₃ phase without detectable secondary phases. In contrast, PbI₂‐rich growth conditions are found to lead to the non‐perovskite δ‐phase. Photoluminescence spectroscopy and optical‐pump THz‐probe mapping show carrier lifetimes larger than 75 ns and charge carrier (sum) mobilities larger than 60 cm² V^?1 s^?1 for the γ‐phase, indicating their suitability for high efficiency solar cells. The dependence of the carrier mobilities and luminescence peak energy on the Cs‐content in the films indicates the presence of Schottky defect pairs, which may cause the stabilization of the γ‐phase. Building on these results, p–i–n type solar cells with a maximum efficiency exceeding 12% and high shelf stability of more than 1200 h are demonstrated, which in the future could still be significantly improved, judging on their bulk optoelectronic properties.     

14.1% CsPbI3 Perovskite Quantum Dot Solar Cells via Cesium Cation Passivation

Surface manipulation of quantum dots (QDs) has been extensively reported to be crucial to their performance when applied into optoelectronic devices, especially for photovoltaic devices. In this work, an efficient surface passivation method for emerging CsPbI₃ perovskite QDs using a variety of inorganic cesium salts (cesium acetate (CsAc), cesium idodide (CsI), cesium carbonate (Cs₂CO₃), and cesium nitrate (CsNO₃)) is reported. The Cs‐salts post‐treatment can not only fill the vacancy at the CsPbI₃ perovskite surface but also improve electron coupling between CsPbI₃ QDs. As a result, the free carrier lifetime, diffusion length, and mobility of QD film are simultaneously improved, which are beneficial for fabricating high‐quality conductive QD films for efficient solar cell devices. After optimizing the post‐treatment process, the short‐circuit current density and fill factor are significantly enhanced, delivering an impressive efficiency of 14.10% for CsPbI₃ QD solar cells. In addition, the Cs‐salt‐treated CsPbI₃ QD devices exhibit improved stability against moisture due to the improved surface environment of these QDs. These findings will provide insight into the design of high‐performance and low‐trap‐states perovskite QD films with desirable optoelectronic properties.     

Soft Template‐Controlled Growth of High‐Quality CsPbI3 Films for Efficient and Stable Solar Cells

The unfavorable morphology and inefficient utilization of phase transition reversibility have limited the high‐temperature‐processed inorganic perovskite films in both efficiency and stability. Here, a simple soft template‐controlled growth (STCG) method is reported by introducing (adamantan‐1‐yl)methanammonium to control the nucleation and growth rate of CsPbI₃ crystals, which gives rise to pinhole‐free CsPbI₃ film with a grain size on a micrometer scale. The STCG‐based CsPbI₃ perovskite solar cell exhibits a power conversion efficiency of 16.04% with significantly reduced defect densities and charge recombination. More importantly, an all‐inorganic solar cell with the architecture fluorine‐doped tin oxide (FTO)/NiO_x/STCG‐CsPbI₃/ZnO/indium‐doped tin oxide (ITO) is successfully fabricated to demonstrate its real advantage in thermal stability. By suppressing the inductive effect of defects during the phase transition and utilizing the unique reversibility of the phase transition for the high‐temperature‐processed CsPbI₃ film, the all‐inorganic solar cell retains 90% of its initial efficiency after 3000 h of continuous light soaking and heating.     

Highly Air‐Stable Single‐Crystalline β‐CsPbI3 Nanorods: A Platform for Inverted Perovskite Solar Cells

The synthesis of single‐crystalline β‐CsPbI₃ perovskite nanorods (NRs) using a colloidal process is reported, exhibiting their improved photostability under 45–55% humidity. The crystal structure of CsPbI₃ NRs films is investigated using Rietveld refined X‐ray diffraction (XRD) patterns to determine crystallographic parameters and the phase transformation from orthorhombic (γ‐CsPbI₃) to tetragonal (β‐CsPbI₃) on annealing at 150 °C. Atomic resolution transmission electron microscopy images are utilized to determine the probable atomic distribution of Cs, Pb, and I atoms in a single β‐phase CsPbI₃ NR, in agreement with the XRD structure and selected area electron diffraction pattern, indicating the growth of single crystalline β‐CsPbI₃ NR. The calculation of the electronic band structure of tetragonal β‐CsPbI₃ using density functional theory (DFT) reveals a direct transition with a lower band gap and a higher absorption coefficient in the solar spectrum, as compared to its γ‐phase. An air‐stable (45–55% humidity) inverted perovskite solar cell, employing β‐CsPbI₃ NRs without any encapsulation, yields an efficiency of 7.3% with 78% enhancement over the γ‐phase, showing its potential for future low cost photovoltaic devices.     

Structurally Reconstructed CsPbI2Br Perovskite for Highly Stable and Square‐Centimeter All‐Inorganic Perovskite Solar Cells

Although all‐inorganic perovskite solar cells (PSCs) demonstrate high thermal stability, cesium‐lead halide perovskites with high iodine content suffer from poor stability of the black phase (α‐phase). In this study, it is demonstrated that incorporating InCl₃ into the host perovskite lattice helps to inhibit the formation of yellow phase (δ‐phase) perovskite and thereby enhances the long‐term ambient stability. The enhanced stability is achieved by a strategy for the structural reconstruction of CsPbI₂Br perovskite by means of In³⁺ and Cl^? codoping, which gives rise to a significant improvement in the overall spatial symmetry with a closely packed atom arrangement due to the crystal structure transformation from orthorhombic (Pnma) to cubic (Pm‐3m). In addition, a novel thermal radiation heating method that further improves the uniformity of the perovskite thin films is presented. This approach enables the construction of all‐inorganic InCl₃:CsPbI₂Br PSCs with a champion power conversion efficiency of 13.74% for a small‐area device (0.09 cm²) and 11.4% for a large‐area device (1.00 cm²).     

In Situ Grain Boundary Functionalization for Stable and Efficient Inorganic CsPbI2Br Perovskite Solar Cells

The phase instability and large energy loss are two obstacles to achieve stable and efficient inorganic‐CsPbI_3?xBr_x perovskite solar cells. In this work, stable cubic perovskite (α)‐phase CsPbI₂Br is successfully achieved by Pb(Ac)₂ functioning at the grain boundary under low temperature. Ac^? strongly coordinates with CsPbI₂Br to stabilize the α‐phase and also make the grain size smaller and film uniform by fast nucleation. PbO is formed in situ at the grain boundary by decomposing Pb(Ac)₂ at high‐temperature annealing. The semiconducting PbO effectively passivates the surface states, reduces the interface recombination, and promotes the charge transport in CsPbI₂Br perovskite solar cells. A 12% efficiency and good stability are obtained for in situ PbO‐passivated CsPbI₂Br solar cells, while Pb(Ac)₂‐passivated device exhibits 8.7% performance and the highest stability, much better than the control device with 8.5% performance and inferior stability. This article highlights the extrinsic ionic grain boundary functionalization to achieve stable and efficient inorganic CsPbI_3?xBr_x materials and the devices.     

µ‐Graphene Crosslinked CsPbI3 Quantum Dots for High Efficiency Solar Cells with Much Improved Stability

All‐inorganic perovskite CsPbI₃ quantum dots (QDs) offer much better stability for photovoltaic applications. Unfortunately, their cell efficiencies are hindered by the low carrier transport efficiency of QD‐assembled films. In addition, agglomeration‐induced phase change of QDs poses another problem for material and device degradation. Herein, the use of µ‐graphene (µGR) to crosslink QDs to form µGR/CsPbI₃ film is demonstrated. It is found that the resultant QDs film provides not only an effective channel for carrier transport, as witnessed by much improved conductivity but also significantly better stability against moisture, humidity, and high temperature stresses. The µGR/CsPbI₃ based solar cell shows increased device performance. More specifically, compared to the solar cell without the µGR treatment, V_OC is improved to 1.18 from 1.16 V, J_SC to 13.59 from 13.17 mA cm^?2, and FF to 72.6 from 68.1%, and overall power conversion efficiency to as high as 11.40 from 10.41%, a 12% increase. In addition, the instability originating from the thermal/moisture‐induced QD agglomeration is also greatly suppressed by the µGR crosslinking. The optimized device retains >98% of its initial efficiency after being stored in N₂ atmosphere for one month. Importantly, under 60% humidity and 100 °C thermal stresses, the µGR/CsPbI₃ devices show much better stability.     

A Novel Anion Doping for Stable CsPbI2Br Perovskite Solar Cells with an Efficiency of 15.56% and an Open Circuit Voltage of 1.30 V

The Cs‐based inorganic perovskite solar cells (PSCs), such as CsPbI₂Br, have made a striking breakthrough with power conversion efficiency (PCE) over 16% and potential to be used as top cells for tandem devices. Herein, I^? is partially replaced with the acetate anion (Ac^?) in the CsPbI₂Br framework, producing multiple benefits. The Ac^? doping can change the morphology, electronic properties, and band structure of the host CsPbI₂Br film. The obtained CsPbI_2?x Br(Ac)_x perovskite films present lower trap densities, longer carrier lifetimes, and fast charge transportation compared to the host CsPbI₂Br films. Interestingly, the CsPbI_2?x Br(Ac)_x PSCs exhibit a maximum PCE of 15.56% and an ultrahigh open circuit voltage (V_oc) of 1.30 V without sacrificing photocurrent. Notably, such a remarkable V_oc is among the highest values of the previously reported CsPbI₂Br PSCs, while the PCE far exceeds all of them. In addition, the obtained CsPbI_2?x Br(Ac)_x PSCs exhibit high reproducibility and good stability. The stable CsPbI_2?x Br(Ac)_x PSCs with high V_oc and PCE are desirable for tandem solar cell applications.     

Composition Engineering in Doctor‐Blading of Perovskite Solar Cells

Organic–inorganic halide perovskite (OIHP) solar cells with efficiency over 18% power conversion efficiency (PCE) have been widely achieved with lab scale spin‐coating method which is however not scalable for the fabrication of large area solar panels. The PCEs of OIHP solar cells made by scalable deposition methods, such as doctor‐blading or slot‐die coating, have been lagging far behind than spin‐coated devices. In this study the authors report composition engineering in doctor‐bladed OIHP solar cells with p–i–n planar heterojunction structure to enhance their efficiency. Phase purer OIHP thin films are obtained by incorporating a small amount of cesium (Cs⁺) and bromine (Br^?) ions into perovskite precursor solution, which also reduces the required film formation temperature. Pinhole free OIHP thin films with micrometer‐sized grains have been obtained assisted by a secondary grain growth with added methylammonium chloride into the precursor solution. The OIHP solar cells using these bladed thin films achieved PCEs over 19.0%, with the best stabilized PCE reaching 19.3%. This represents a significant step toward scalable manufacture of OIHP solar cells.     

In Situ Polymerization of Cross-Linked Perovskite–Polymer Composites for Highly Stable and Efficient Perovskite Solar Cells

Mixed-halide perovskites have emerged as outstanding light absorbers that enable the fabrication of efficient solar cells; however, their instability hinders the commercialization of such systems. Grain-boundary (GB) defects and lattice tensile strain are critical intrinsic-instability factors in polycrystalline perovskite films. In this study, the light-induced cross-linking of acrylamide (Am) monomers with non-crystalline perovskite films is used to fabricate highly efficient and stable perovskite solar cells (PSCs). The Am monomers induce the preferred crystal orientation in the polycrystalline perovskite films, enlarge the perovskite grain size, and cross-link the perovskite grains. Additionally, the liquid properties of Am effectively releases lattice strain during perovskite-film crystallization. The cross-linked interfacial layer functions as an airtight wall that protects the perovskite film from water corrosion. Devices fabricated using the proposed strategy show an excellent power conversion efficiency (PCE) of 24.45% with an open-circuit voltage (V_OC) of 1.199 V, which, to date, is the highest V_OC reported for hybrid PSCs with electron transport layers (ETLs) comprised of TiO₂. Large-area PSC modules fabricated using the proposed strategy show a power conversion efficiency of 20.31% (with a high fill factor of 77.1%) over an active area of 33 cm², with excellent storage stability.     

Inorganic CsPbI3 Perovskite Coating on PbS Quantum Dot for Highly Efficient and Stable Infrared Light Converting Solar Cells

Solution‐processed colloidal quantum dot (CQD) solar cells harvesting the infrared part of the solar spectrum are especially interesting for future use in semitransparent windows or multilayer solar cells. To improve the device power conversion efficiency (PCE) and stability of the solar cells, surface passivation of the quantum dots is vital in the research of CQD solar cells. Herein, inorganic CsPbI₃ perovskite (CsPbI₃‐P) coating on PbS CQDs with a low‐temperature, solution‐processed approach is reported. The PbS CQD solar cell with CsPbI₃‐P coating gives a high PCE of 10.5% and exhibits remarkable stability both under long‐term constant illumination and storage under ambient conditions. Detailed characterization and analysis reveal improved passivation of the PbS CQDs with the CsPbI₃‐P coating, and the results suggest that the lattice coherence between CsPbI₃‐P and PbS results in epitaxial induced growth of the CsPbI₃‐P coating. The improved passivation significantly diminishes the sub‐bandgap trap‐state assisted recombination, leading to improved charge collection and therefore higher photovoltaic performance. This work therefore provides important insight to improve the CQD passivation by coating with an inorganic perovskite ligand for photovoltaics or other optoelectronic applications.     

Diammonium and Monoammonium Mixed‐Organic‐Cation Perovskites for High Performance Solar Cells with Improved Stability

Remarkable power conversion efficiencies (PCE) of metal–halide perovskite solar cells (PSCs) are overshadowed by concerns about their ultimate stability, which is arguably the prime obstacle to commercialization of this promising technology. Herein, the problem is addressed by introducing ethane‐1,2‐diammonium (⁺NH₃(CH₂)₂NH₃⁺, EDA²⁺) cations into the methyl ammonium (CH₃NH₃⁺, MA⁺) lead iodide perovskite, which enables, inter alia, systematic tuning of the morphology, electronic structure, light absorption, and photoluminescence properties of the perovskite films. Incorporation of <5 mol% EDA²⁺ induces strain in the perovskite crystal structure with no new phase formed. With 0.8 mol% EDA²⁺, PCE of the MAPbI₃‐based PSCs (aperture of 0.16 cm²) improves from 16.7% ± 0.6% to 17.9% ± 0.4% under 1 sun irradiation, and fabrication of larger area devices (aperture 1.04 cm²) with a certified PCE of 15.2% ± 0.5% is demonstrated. Most importantly, EDA²⁺/MA⁺‐based solar cells retain 75% of the initial performance after 72 h of continuous operation at 50% relative humidity and 50 °C under 1 sun illumination, whereas the MAPbI₃ devices degrade by approximately 90% within only 15 h. This substantial improvement in stability is attributed to the steric and coulombic interactions of embedded EDA²⁺ in the perovskite structure.     

Universal Strategy with Structural and Chemical Crosslinking Interface for Efficient and Stable Perovskite Solar Cells

Due to the limited interface contact and weak interfacial interaction, planar heterojunction perovskite solar cells (PSCs) have space for further improvement. Herein, a structural and chemical crosslinking interface is proposed and constructed by introducing an extra layer, which blends tin dioxide (SnO₂) nanoparticles with chloride salts. Since the incorporated materials can be dissolved during the fabrication of perovskite, the quality of perovskite films is improved, leading to larger grain size and reduced trap-state density. Also, more chloride ions at the SnO₂/perovskite interface are observed and the interaction between Cl⁻ and Sn⁴⁺ is confirmed. It results in more pronounced n-type SnO₂ with better conductivity and deeper conduction bands, leading to preferable energy level alignment between SnO₂ and perovskite. Consequently, the open-circuit voltage and fill factor of the devices increase, and target cells present better stability, retaining 98% of initial efficiencies after >10 000 h storage in dry air (≈5% relative humidity) and maintaining 85.50% of the initial efficiency after 1000 h of operation under light. This strategy enables the achievement of 25.28% efficiency with a low bandgap (1.53 eV) perovskite composition, and it is confirmed to be universal when other related materials are utilized.     

Morphology Controlling of All‐Inorganic Perovskite at Low Temperature for Efficient Rigid and Flexible Solar Cells

All‐inorganic cesium lead halide (CsPbX₃) perovskites have emerged as promising photovoltaic materials owing to their superior thermal stability compared to traditional organic–inorganic hybrid counterparts. However, the CsPbX₃ perovskites generally need to be prepared at high‐temperature, which restricts their application in multilayer or flexible solar cells. Herein, the formation of CsPbX₃ perovskites at room‐temperature (RT) induced by dimethylsulphoxide (DMSO) coordination is reported. It is further found that a RT solvent (DMSO) annealing (RTSA) treatment is valid to control the perovskite crystallization dynamics, leading to uniform and void‐free films, and consequently a maximum power conversion efficiency (PCE) of 6.4% in the device indium tin oxide (ITO)/NiO _x /RT‐CsPbI₂Br/C₆₀/Bathocuproine (BCP)/Ag, which is, as far as it is known, the first report of RT solution‐processed CsPbX₃‐based perovskite solar cells (PSCs). Moreover, the efficiency can be boosted up to 10.4% by postannealing the RTSA‐treated perovskite film at an optimal temperature of 120 °C. Profiting from the moderate temperature, flexible PSCs are also demonstrated with a maximum PCE of 7.3% for the first time. These results may stimulate further development of all‐inorganic CsPbX₃ perovskites and their application in flexible electronics.     

The Spacer Cations Interplay for Efficient and Stable Layered 2D Perovskite Solar Cells

Organic spacer cations in layered 2D (A₁)₂(A₂)_n?1B_nX_3n+1 (where A₁ is an organic cation acting as a spacer between the perovskite layers, A₂ is a monovalent cation, e.g., Cs⁺,CH₃NH₃⁺, CH(NH₂)₂⁺) perovskite materials improve the long‐term stability of the resulting solar cells, but hamper their power conversion efficiency due to poor carrier generation/transportation. Rational guidelines are thus required to enable the design of organic spacer cations. Herein, mixed A₁ cations are employed in layered 2D perovskites to investigate the interplay between alkylamine cations and unsaturated alkylamine cations. It is revealed that alkylamine spacer cations are able to facilitate precursor assembly, which results in the orientated growth of perovskite crystals. Unsaturated alkylamine cations further lead to reduced exciton binding energy, which improves carrier pathway in the 2D perovskites. By mixing both cations, substantially improved open circuit voltage is observed in the resultant photovoltaic cells with the efficiency of 15.46%, one of the highest one based on (A₁)₂(A₂)₃Pb₄I₁₃ layered 2D perovskites. The generality of the design principle is further extended to other cation combinations.     

Stabilizing the Efficiency Beyond 20% with a Mixed Cation Perovskite Solar Cell Fabricated in Ambient Air under Controlled Humidity

Perovskite solar cells have evolved to have compatible high efficiency and stability by employing mixed cation/halide type perovskite crystals as pinhole‐free large grain absorbers. The cesium (Cs)–formamidium–methylammonium triple cation‐based perovskite device fabricated in a glove box enables reproducible high‐voltage performance. This study explores the method to reproduce stable and high power conversion efficiency (PCE) of a triple cation perovskite prepared using a one‐step solution deposition and low‐temperature annealing fully conducted in controlled ambient humidity conditions. Optimizing the perovskite grain size by Cs concentration and solution processes, a route is created to obtain highly uniform, pinhole‐free large grain perovskite films that work with reproducible PCE up to 20.8% and high preservation stability without cell encapsulation for more than 18 weeks. This study further investigates the light intensity characteristics of open‐circuit voltage (V_oc) of small (5 × 5 mm², PCE > 20%) and large (10 × 10 mm², PCE of 18%) devices. Intensity dependence of V_oc shows an ideality factor in the range of 1.7‐1.9 for both devices, implying that the triple cation perovskite involves trap‐assisted recombination loss at the hetero junction interfaces that influences V_oc. Despite relatively high ideality factor, perovskite device is capable of supplying high power conversion efficiency under low light intensity (0.01 Sun) whereas maintaining V_oc over 0.9 V.     

Localization of inorganic ions by precipitative freeze dissolution

Summary A new method for localization of inorganic diffusible ions in tissue is introduced. It has been applied to localization of Tl⁺ and Rb⁺ in barley roots and is probably also suited for Cs⁺, Ca²⁺, Cl^–, Br^–, PO ₄ ^3– and perhaps K⁺. Its principle consists of dissolution of the ice from frozen tissue in a concentrated aqueous solution of a precipitating agent that is kept at a temperature just above its melting point.