Effect of carbopol and polyvinylpyrrolidone on the mechanical, rheological, and release properties of bioadhesive polyethylene glycol gels

This study examined the mechanical (hardness, compressibility, adhesiveness, and cohesiveness) and rheological (zero-rate viscosity and thixotropy) properties of polyethylene glycol (PEG) gels that contain different ratios of Carbopol 934P (CP) and polyvinylpyrrolidone K90 (PVP). Mechanical properties were examined using a texture analyzer (TA-XT2), and rheological properties were examined using a rheometer (Rheomat 115A). In addition, lidocaine release from gels was evaluated using a release apparatus simulating the buccal condition. The results indicated that an increase in CP concentration significantly increased gel compressibility, hardness, and adhesiveness, factors that affect ease of gel removal from container, ease of gel application onto mucosal membrane, and gel bioadhesion. However, CP concentration was negatively correlated with gel cohesiveness, a factor representing structural reformation. In contrast, PVP concentration as negatively correlated with gel hardness and compressibility, but positively correlated with gel cohesiveness. All PEG gels exhibited pseudoplastic flow with thixotropy, indicating a general loss of consistency with increased shearing stress. Drug release T_50% was affected by the flow rate of the simulated saliva solution. A reduction in the flow rate caused a slower drug release and hence a higher T_50% value. In addition, drug release was significantly reduced as the concentrations of CP and PVP increased because of the increase in zero-rate viscosity of the gels. Response surfaces and contour plots of the dependent variables further substantiated that various combinations of CP and PVP in the PEG gels offered a wide range of mechanical, rheological, and drug-release characteristics. A combination of CP and PVP with complementary physical properties resulted in a prolonged buccal drug delivery.     

Effect of shearing on formation of silk fibers from regenerated Bombyx mori silk fibroin aqueous solution

In this paper, the spinnable regenerated silk fibroin aqueous solution with high concentration was prepared and the regenerated silk fibers were obtained from the aqueous solution by two different spinning processes at ambient temperature. The orientation of these fibers was characterized by polarizing microscope. Their secondary structure was investigated by Raman spectroscopy and related mechanical properties were also measured. These data showed that shearing is an important step for increasing orientation and silk II (β-sheet) structure, and the mechanical properties of the regenerated silk fibers can also be improved by shearing.     

Interpreting food processing through dietary mechanical properties: a Lemur catta case study

Knowledge of dietary mechanical properties can be informative about physical consequences to consumers during ingestion and mastication. In this article, we examine how Tamarindus indica fruits can affect dental morphology in a population of ring-tailed lemurs (Lemur catta) at Beza Mahafaly special reserve in southwestern Madagascar. Ring-tailed lemurs in tamarind dominated gallery forests exhibit extreme wear and tooth loss on their postcanine dentition that has been related to processing T. indica fruits. We measured and compared mechanical properties of individual food parts in the diet of ring-tailed lemurs in different seasons in 1999-2000, 2008, and 2010. Fracture toughness, hardness, and modulus of foods were measured with a portable mechanical tester. The ripe fruits of T. indica are indeed the toughest and hardest foods ingested by the lemurs. In addition, they are among the largest foods consumed, require high numbers of ingestive bites to process, and are the most frequently eaten by volume. During controlled cutting tests of the ripe fruit shell, multiple runaway side cracks form alongside the cut. Similarly, the lemurs repeatedly bite the ripe shell during feeding and thereby introduce multiple cracks that eventually fragment the shell. Studies of enamel microstructure (e.g., Lucas et al.: BioEssays 30 (2008) 374-385; Campbell et al., 2011) advance the idea that the thin enamel of ring-tailed lemur teeth is susceptible to substantial micro-cracking that rapidly erodes the teeth. We conclude that micro-cracking from repeated loads, in combination with the mechanical and physical properties of the fruit, is primarily responsible for the observed dental damage.     

Effects of shearing on chromatin structure

The effects of mechanical shearing on chromatin structure were investigated by using thermal denaturation and circular dichroism (CD) spectroscopy. Under ordinary conditions of mechanical shearing used for preparation of soluble chromatin, we observed only minor changes (less than 10%) of chromatin properties with respect to (a) absorption melting curves, (b) CD spectra, (c) CD melting curves and (d) histone transfer from chromatin to exogenous DNA. Such small pertubation of structural properties could be due to the generation of free ends when a large chromatin was cut into smaller fragments and by weakening the binding of histones to DNA near these free ends. In addition to mechanical shearing, sonication was used to shear some samples of chromatin. The effect of sonication on chromatin structure was investigated by the same physical methods used for mechanically sheared chromatin. The results indicate that sonication only slightly changes the chromatin properties with respect to CD spectra, similar to the results obtained by mechanical shearing, but sonication at high settings has a greater effect on the thermal denaturation property of chromatin as contrasted to our results from mechanically sheared chromatin.     

A shearing technique measuring resistance properties of plant stems

A shearing technique was developed to measure fracturing properties of plant stems. Shearing force measurements assess the amount of energy required to fragment plant tissue as an indication of resistance to particle breakdown during mastication. The objective of this study was to develop a rapid and inexpensive method of accurately measuring the shearing properties of forage stems. Shearing properties of alfalfa stems were measured by shearing 20 main stems from each of 24 cultivars. Stems were dried and divided into three 16 cm segments, top, middle and bottom. Each segment was sheared between two nodes at the approximate mid-point using an Ottawa Texture Measurement System with a Warner-Bratzler blade (dull grade) lowered at 1.35 mm s⁻¹. Instrument repeatability was determined using a homogenous material (plastic coffee stirrers) with mechanical and textural properties similar to those of a plant stem. The shearing technique provided a repeatable and rapid measurement of shearing force (coefficient of variation for plastic stirrers, 4.2%). For alfalfa stems harvested at similar physiological maturity, shearing forces for each shearing location on the stem differed (P < 0.001) among cultivars. At all shearing locations, shearing force varied considerably between cultivars; however, variations among shearing locations were similar. Shearing force was significantly correlated with diameter, weight, linear density and, to a lesser extent, with the cell wall chemical constituents of the stem.     

Biocompatible epoxy modified bio-based polyurethane nanocomposites: Mechanical property, cytotoxicity and biodegradation

Epoxy modified Mesua ferrea L. seed oil (MFLSO) based polyurethane nanocomposites with different weight % of clay loadings (1%, 2.5% and 5%) have been evaluated as biocompatible materials. The nanocomposites were prepared by ex situ solution technique under high mechanical shearing and ultrasonication at room temperature. The partially exfoliated nanocomposites were characterized by Fourier transform infra-red (FTIR), X-ray diffraction (XRD), scanning electron microscopy (SEM) and transmission electron microscopy (TEM) techniques. The mechanical properties such as tensile strength and scratch hardness were improved 2 and 5 times, respectively by nanocomposites formation. Even the impact resistance improved a little. The thermostability of the nanocomposites was enhanced by about 40 °C. Biodegradation study confirmed 5–10 fold increase in biodegradation rate for the nanocomposites compared to the pristine polymers. All the nanocomposites showed non-cytotoxicity as evident from RBC hemolysis inhibition observed in anti-hemolytic assay carried over the sterilized films. The study reveals that the epoxy modified MFLSO based polyurethane nanocomposites deserve the potential to be applicable as biomaterials.     

Methods of assessing leaf-fracture properties

Numerous authors have attempted to quantify the physical properties of leaves in relation to aspects of leaf ecology, including decomposition, sclerophylly, herbivory, and leaf function and longevity. This paper examines the relative merits of the punch-and-die, tearing and shearing tests for assessing leaf physical properties. We conducted a series of these three mechanical tests on leaves of Solanum laciniatum , and determined the effect of various test parameters on the measurement of fracture properties. For the punch-and-die test, the parameters considered were machine speed, clearance between the punch and the die, edge definition of the punch, and area of the punch. Aspects of the tearing test examined were notch length, end effects, and length-to-width requirements of test strips, and for shearing tests the effects of blade proximity, angle and sharpness were investigated. All the test parameters investigated were found significantly to affect the assessment of leaf-fracture properties. In addition, fracture properties were found to vary significantly within leaves. Some general principles for designing and implementing tests are outlined. This study suggests that while punching and shearing tests are useful means of quantifying leaf fracture properties, the value of the tearing test may be reduced as it is most constrained by the biological nature of the test material.     

Mechanical resistance of wheat straw after incubation in cultures of ruminal cellulolytic microorganisms

The mechanical properties of wheat straw fragments were measured using tensile and shear tests before and after incubation in pure cultures of the rumen fungus Neocallimastix frontalis MCH3, in pure cultures of the rumen cellulolytic bacteria Fibrobacter succinogenes S85 and Ruminococcus flavefaciens 007 and in co-cultures associating the fungus with each of the two bacterial species.

N. frontalis considerably reduced the tensile strength of the straw; on the contrary R. flavefaciens increased it and F. succinogenes did not affect it. In co-cultures, F. succinogenes and N. frontalis interacted synergistically to weaken straw resistance, whereas R. flavefaciens inhibited the fungal action. The shear test also revealed that physical and mechanical properties were strongly affected by the action of the three microorganisms. After six days of incubation the straws resistance to shearing was lower after incubation with N. frontalis or R. flavefaciens than in the presence of F. succinogenes. No synergism or antagonism between microorganisms was observed in the shear test.

These results thus clearly demonstrate a specific action of the three rumen microorganisms in physical degradation of plant material.     

皮肤模型与微针穿刺性能评价的研究

微针阵列作为新型透皮给药技术,受到广泛关注。通常以刺入力、刺入率和刺入深度来评价微针刺入皮肤的程度和效率。皮肤是其性能评价的基础。皮肤的物理特性主要由角蛋白丝、胶原纤维、弹性纤维和皮下组织综合决定,并且从厚度、弹性、硬度和韧性等维度反映其对微针刺入的影响。机械的、渗透的、组织的和屏障的等皮肤模型被用于解读和模拟真实皮肤的该方面功能。同样,通过皮肤力学分析后建立的包括本构模型在内的各种皮肤力学模型也从物理维度解析皮肤的力学特征。真实皮肤具有复杂性,存在差异性大、不易获取和储存,以及伦理等问题,而皮肤模型可在一定程度上代替真实皮肤辅助微针递送系统设计、开发和性能评价。本文系统回顾分析了皮肤组织的物理特性、各种皮肤模型的制备及特点、真实皮肤和模拟皮肤在评价微针穿刺性能方面的应用,为开发及建立合适的皮肤模型提供借鉴。     

Performance of oak,beech and spruce beams after more than 100 years in service

The aim of this study was to investigate differences in the mechanical and fungicidal properties of three different wood species (English oak (Quercus sp.), common beech (Fagus sylvatica) and Norway spruce (Picea abies)) that had been in indoor use for several decades, compared to control specimens of freshly cut timber. The collected material was cut into smaller samples prior to further analysis. Extractive content, mechanical, fungicidal and sorption properties were determined according to standard procedures. The obtained results showed that the mechanical properties of oak wood do not deteriorate over the investigated time frame. On the other hand, the resistance of oak wood against fungi decreases over time. The reason for this is yet to be confirmed; it may be due to degradation of secondary metabolites. Similar results have been reported for spruce wood. There were no statistically significant differences in the mechanical properties of old and new spruce wood. In contrast to oak wood, there were also no significant differences in fungicidal properties, bearing in mind that spruce wood has lower durability than oak wood. Aging of beech wood resulted in a considerable decrease in the tested mechanical properties but showed no significant differences in fungicidal properties. Old beech wood specimens were moderately deteriorated by insects and fungi, which was the reason for the loss of bending and compressive strength. Our results confirm that most of the relevant properties do not deteriorate with time and that wood can be reused for a variety of other applications even after decades in service.     

Tannin-based rigid foams: A survey of chemical and physical properties

Tannin-based rigid foams, prepared from 95% natural material, are suggested for replacing synthetic phenol–formaldehyde foams in various applications. For that purpose, a few physical properties were measured and reported here: resistance to fire and chemicals, absorption of various liquids, permeability, thermal conductivity and mechanical (compressive and tensile) strength. Modifying the composition through the use of boric and/or phosphoric acid allowed substantial increase of fire resistance. The materials were also found to present good resistance to strong acid and bases, and to solvents. High affinity for water, but limited one for organic liquids, was also evidenced. Finally, slightly anisotropic mechanical properties were measured. The materials present a brittle behaviour, whether tested in compression or traction; nevertheless, their strengths, as well as their thermal conductivities, are fully comparable with those of their phenolic counterparts. We show that such materials of vegetable origins can compete with synthetic ones for most of traditional applications.     

A Novel Multifunctional Crosslinking PVA/CMCS Hydrogel Containing Cyclic Peptide Actinomycin X2 and PA@Fe with Excellent Antibacterial and Commendable Mechanical Properties

Bacterial infected environments and resulting bacterial infections have been threatening the human health globally. Due to increased bacterial resistance caused by improper and excessive use of antibiotics, antibacterial biomaterials are being developed as alternatives to antibiotics in some cases. Herein, an advanced multifunctional hydrogel with excellent antibacterial properties, enhanced mechanical properties, biocompatibility and self-healing performance, was designed through freezing-thawing method. This hydrogel network is composed of polyvinyl alcohol (PVA), carboxymethyl chitosan (CMCS), protocatechualdehyde (PA), ferric iron (Fe) and an antimicrobial cyclic peptide actinomycin X2 (Ac.X2). The double dynamic bonds among protocatechualdehyde (PA), ferric iron (Fe) and carboxymethyl chitosan containing coordinate bond (catechol-Fe) as well as dynamic Schiff base bonds and hydrogen bonds endowed the hydrogel with enhanced mechanical properties. Successful formation of hydrogel was confirmed through ATR-IR and XRD, and structural evaluation through SEM analysis, whereas mechanical properties were tested with electromechanical universal testing machine. The resulting PVA/CMCS/Ac.X2/PA@Fe (PCXPA) hydrogel has favorable biocompatibility and excellent broad-spectrum antimicrobial activity against both S. aureus (95.3 %) and E. coli (90.2 %) compared with free-soluble Ac.X2, which exhibited subpar performance against E. coli reported in our previous studies. This work provides a new insight on preparing multifunctional hydrogels containing antimicrobial peptides as antibacterial material.     

High biobased content epoxy-anhydride thermosets from epoxidized sucrose esters of Fatty acids

Novel highly functional biobased epoxy compounds, epoxidized sucrose esters of fatty acids (ESEFAs), were cross-linked with a liquid cycloaliphatic anhydride to prepare polyester thermosets. The degree of cure or conversion was studied using differential scanning calorimetry (DSC), and the sol content of the thermosets was determined using solvent extraction. The mechanical properties were studied using tensile testing to determine Young's modulus, tensile stress, and elongation at break. Dynamic mechanical analysis (DMA) was used to determine glass-transition temperature, storage modulus, and cross-link density. The nanomechanical properties of the surfaces were studied using nanoindentation to determine reduced modulus and indentation hardness. The properties of coatings on steel substrates were studied to determine coating hardness, adhesion, solvent resistance, and mechanical durability. Compared with the control, epoxidized soybean oil, the anhydride-cured ESEFAs have high modulus and are hard and ductile, high-performance thermoset materials while maintaining a high biobased content (71-77% in theory). The exceptional performance of the ESEFAs is attributed to the unique structure of these macromolecules: well-defined compact structures with high epoxide functionality. These biobased thermosets have potential uses in applications such as composites, adhesives, and coatings.     

First principles investigation of pressure dependent stability,phonon, Debye temperature,physical, mechanical and thermodynamic properties of Rh3Al intermetallic compound

ABSTRACT

Pressure dependence of stability, phonon, Debye temperature, physical, mechanical and thermodynamic properties of Rh₃Al intermetallic compound were investigated by first-principles The calculated cohesive energy (E_c), formation enthalpy (ΔH) show that Rh₃Al is a thermodynamically stable compound. Properties related to the phonons of Rh₃Al were also obtained. In addition, the transverse sound velocity (ν_s), longitudinal sound velocity (ν_l), average sound velocity (ν_m) and Debye temperature (Θ_D) of Rh₃Al were calculated by using the VRH method along with pressure range from 0 to 60?GPa. The values of lattice parameters, bulk modulus and its first-order pressure derivative are consistent well with other works. The band structure indicates that Rh₃Al compound exhibits a metallic character. Moreover, the total density of states, partial density of states, Mulliken charges and electron density difference have been analysed to explain the physical properties. Based on the stress–strain approach and the Born stability criteria, the mechanical properties were evaluated by elastic constants (C_ij), other modulus (B, E, G), (B/G) ratio, Poisson’s ratio (ν), the anisotropic index (A), hardness (H) and compressibility (K) for this intermetallic compound. Finally, the thermodynamic properties, including enthalpy, free energy, entropy and heat capacity are discussed range from 0 to 1000?K.     

Clonal consistency of wood technological properties in canker-resistant <Emphasis Type="Italic">Cupressus sempervirens</Emphasis> clones at two contrasting sites

Cupressus sempervirens L. (Mediterranean cypress) has been traditionally used as a multipurpose tree. In the past, its wood was extensively used as a highly durable raw material in the Mediterranean, but nowadays, production of cypress wood is constrained by the lack of exploitable woods and plantations and by the spread of bark canker. In this study, the wood properties of canker-resistant clones specifically meant for timber production were assessed in two different locations. The aim was to evaluate the effect of genotype and environment on physical and mechanical properties of wood and its bonding quality. Four ramets of each of 10 clones were sampled in both sites, wood density, shrinkage, hardness, and the bonding strengths when glued together with two different adhesives were determined, and clonal repeatabilities and genetic correlations were also estimated. Clonal consistency for wood traits was moderate to high within and across environments, far higher than for growth- and morphological traits. Indications are that selection based exclusively on tree height would result in a lower wood density and hardness. Bonding strength reflected the combination of the material properties and the selected adhesive: For adhesive M (polyvinyl acetate dispersion), it was negatively correlated with density, whilst for adhesive E (emulsion polymerization isocyanate), it was not as influenced. Thus, even favouring higher-density wood (and therefore not only hardness but also higher shrinkages), adhesive E would give excellent bonding.     

The molecular simulation of the miscibility,mechanical properties and physical cross-linking behavior of the poly(vinyl alcohol)/poly(acrylic acid) composited membranes

The miscibility and mechanical properties of poly vinyl alcohol (PVA) and poly acrylic acid (PAA)-composited membranes were studied with molecular simulation. The Flory–Huggins parameters (δ) were calculated to prove the good miscibility of PVA and PAA. The radial distribution functions of hydroxyl and carboxyl atoms and the average number of H-bonds were observed to indicate the degree of physical cross-linking between PVA and PAA. The influences of intermolecular physical cross-linking on the glass transition temperature and mechanical properties were estimated. The results revealed that the PVA/PAA membrane with a composition of 2:3 has the best plastic properties, which exhibits a good application value. All of the simulated results showed good agreement with the experimental data. It indicates that the method presented in this work has a promising application prospect.     

Enzyme-mediated coupling of a bi-functional phenolic compound onto wool to enhance its physical,mechanical and functional properties

Wool fibres have been modified with nordihydroguaiaretic acid (NDGA) to improve their performance at use. This water insoluble bi-functional phenolic compound has been grafted on wool through a laccase enzyme catalyzed reaction in an aqueous–ethanol mixture. The capacity of laccase to oxidise NDGA in this aqueous–organic medium has been studied electrochemically. The increase of CH₂, CH₃ and aromatic groups signal in the DRIFT spectra, together with SEM images of the enzymatically modified fabrics confirmed the covalent grafting of NDGA on wool. This one step enzymatic process for grafting of NDGA improved the physical and mechanical properties of wool fabrics such as shrink resistance, crease recovery and tensile strength. Furthermore, the NDGA imparted to the textile material strong antioxidant activity and UV protection.     

The dynamic viscoelasticity and plasticizer leachability of tissue conditioners

doi: 10.1111/j.1741‐2358.2012.00639.x
The dynamic viscoelasticity and plasticizer leachability of tissue conditioners Objectives: Dynamic viscoelasticity is one of the most important characteristics of tissue conditioners. Leaching of plasticizer from tissue conditioners may cause changes in the dynamic viscoelasticity of these materials. The purpose of this study was to determine the dynamic viscoelasticity and plasticizer leachability of commercial tissue conditioners. Materials and methods: Five commercial tissue conditioners were used in this study: COE Comfort (CC), Fit Softer (FS), Hydro‐Cast (HC), Soft Conditioner (SC) and Visco‐Gel (VG). Five specimens of each material were stored in 37°C distilled water. The dynamic viscoelasticity and plasticizer leaching of each specimen were measured at 0, 1, 3, 7 and 14 days after immersion using a dynamic mechanical analyzer and high performance liquid chromatography. Data were analyzed using one‐way anova and Student–Newman–Keuls test (α = 0.05). Results: Significant differences in dynamic viscoelasticity and plasticizer leaching were found among the materials. The dynamic viscoelasticity of all materials increased or decreased significantly with time. Rapid changes in dynamic viscoelasticity were evident on day 1 after water immersion. The material CC recorded the highest level of plasticizer leaching. Conclusion: These results suggest that the dynamic viscoelasticity of commercial tissue conditioners is affected by plasticizer leaching. However, these effects are limited.     

On the fracture mechanisms of nacre: Effects of structural orientation

The nacre of mollusk shells is distinguished by an exceptional mechanical efficiency which is derived essentially from its lamellar structure and frequently acts as a source of inspiration for the development of biomimetic materials. The structure and mechanical properties of nacre have been intensively investigated with a special focus on its toughening strategies; nevertheless, the fracture mechanisms, more specifically the critical stress/strain conditions for the failure of nacre, and the effects of structural orientation and hydration state remain largely unexplored. Here uniaxial compression tests were performed on nacre of both dry and hydrated states with different off-axis angles, i.e., the inclination of loading axis with respect to the lamellar structure, ranging from 0° to 90°. The mechanical properties and fracture characteristics of nacre and their dependences on the structural orientation and hydration state were elucidated in terms of mechanics behind failure. Quantitative relationships were established between the mechanical properties and off-axis angle based on different failure criteria. The competition between the fracture modes of fragmentation and shearing was quantified by comparing their respective driving force and resistance on the interfacial plane. This study may aid the understanding on the mechanical behavior of nacre and nacre-inspired synthetic materials and promote a better replication of the underlying design principles of nacre in man-made systems.