Correlation between ground reaction force and tibial acceleration in vertical jumping

Modern electronics allow for the unobtrusive measurement of accelerations outside the laboratory using wireless sensor nodes. The ability to accurately measure joint accelerations under unrestricted conditions, and to correlate them with jump height and landing force, could provide important data to better understand joint mechanics subject to real-life conditions. This study investigates the correlation between peak vertical ground reaction forces, as measured by a force plate, and tibial axial accelerations during free vertical jumping. The jump heights calculated from force-plate data and accelerometer measurements are also compared. For six male subjects participating in this study, the average coefficient of determination between peak ground reaction force and peak tibial axial acceleration is found to be 0.81. The coefficient of determination between jump height calculated using force plate and accelerometer data is 0.88. Data show that the landing forces could be as high as 8 body weights of the jumper. The measured peak tibial accelerations ranged up to 42 g. Jump heights calculated from force plate and accelerometer sensors data differed by less than 2.5 cm. It is found that both impact accelerations and landing forces are only weakly correlated with jump height (the average coefficient of determination is 0.12). This study shows that unobtrusive accelerometers can be used to determine the ground reaction forces experienced in a jump landing. Whereas the device also permitted an accurate determination of jump height, there was no correlation between peak ground reaction force and jump height.     

Muscular strength and jumping performance relationships in young women athletes

The relationships between muscular strength and vertical jumping performance were examined in young women (14-19 years) track and field jumpers (n = 20) and volleyball players (n = 21). The knee extensor muscular strength measured at 9 knee angles was correlated with jumping height and peak power at the squat (SJ) and the countermovement (CMJ) vertical jump tests. Pearson product coefficient of correlation was used to test the significance of these relationships (p 0.80). Specifically, in the volleyball players, the strong relationships were noted for muscular strength at the knee angle range of 40 degrees to 90 degrees and CMJ jumping height as well as SJ peak power. Results indicate the dissimilarity in the relationships between the knee extensor muscular strength and jumping performance in the young female track and field jumpers and volleyball players. In addition, it appears that the measure selected to evaluate jumping performance alters the correlational results.     

The relationship between muscle kinetic parameters and kinematic variables in a complex movement

Kinematic variables of the vertical jump (jumping height, jump phase durations and joint angles) were measured on 39 male physical education students. In addition, kinetic parameters of the hip and knee extensors, and of the plantar flexors (maxima voluntary force and its rate of development) were recorded on the same subjects, in isometric conditions. The results demonstrated significant positive correlations between kinetic parameters of the active muscle groups and jumping height (r = 0.217-0.464). The dominant effect on these correlations was due to the knee extensors. Correlations between these parameters and the duration of the jump phases were much weaker. Correlation coefficients between kinetic parameters and limb angles in the lowest body position showed that fast force production in one muscle group was related to a significant decrease in the joint angles of distant body segments. Multiple correlation coefficients between leg extensor parameters and kinematic variables (ranging between 0.256 for the duration of the counter-movement phase and 0.616 for jump height) suggested that kinetic parameters could explain more than a quarter of the variability of this complex human movement. Therefore, the conclusion was drawn that an extended set of measurements of the relevant musculo-skeletal system parameters could predict a considerable amount of the variability of human movement. However, high correlation coefficients between the same kinetic parameters of different muscle groups suggest that not all active muscle groups have to be included in the measurements.     

Thigh–calf contact: Does it affect the loading of the knee in the high-flexion range?

Recently, high-flexion knee implants have been developed to provide for a large range of motion (ROM>120°) after total knee arthroplasty (TKA). Since knee forces typically increase with larger flexion angles, it is commonly assumed that high-flexion knee implants are subjected to larger loads than conventional knee implants. However, most high-flexion studies do not consider thigh–calf contact which occurs during high-flexion activities such as squatting and kneeling. In this study, we hypothesized that thigh–calf contact reduces the knee forces during deep knee flexion as the tibio-femoral load shifts from occurring inside the knee towards the thigh–calf contact interface. Hence, the effect of thigh–calf contact on the knee loading was evaluated using a free body diagram and a finite element model and both the knee forces and polyethylene stresses were analyzed. Thigh–calf contact force characteristics from an earlier study were included and a squatting movement was simulated. In general, we found thigh–calf contact considerably reduced both the knee forces and polyethylene stresses during deep knee flexion. At maximal flexion (155°), the compressive knee force decreased from 4.89 to 2.90 times the bodyweight (BW) in case thigh–calf contact was included and the polyethylene contact stress at the tibial post decreased from 49.3 to 28.1 MPa. Additionally, there was a clear correlation between a subject's thigh and calf circumference and the force reduction at maximal flexion due to thigh–calf contact (R=0.89). The findings presented in this study can be used to optimize the mechanical behavior of high-flexion total knee arthroplasty designs.     

The EMG activity and mechanics of the running jump as a function of takeoff angle.

To characterize the electromyographic (EMG) activity, ground reaction forces, and kinematics were used in the running jump with different takeoff angles. Two male long jumpers volunteered to perform running jumps at different approach speeds by varying the number of steps (from 3 to 9) in the run-up. Subject TM achieved a greater vertical velocity of the center of gravity (CG) at takeoff for all approach distances. This jumping strategy was associated with greater backward trunk lean at touchdown and takeoff, a lesser range of motion for the thigh during the support phase, more extended knee and ankle angles at touchdown, and a more flexed knee angle at takeoff. Accompanying these differences in kinematics, TM experienced greater braking impulses and lesser propulsion impulses for the forward-backward component of the ground reaction force. Furthermore, TM activated mainly the rectus femoris, vastus medialis, lateral gastrocnemius, and tibialis anterior, while if rarely activated the biceps femoris from just before contact to roughly the first two-thirds of the support phase. These results indicate that TM used a greater takeoff angle in the running jump because he enabled and sustained a greater blocking effect via the coordination patterns of the muscles relative to the hip, knee, and ankle joints. These findings also suggest that the muscle activities recorded in the present experiment are reflected in kinematics and kinetics. Further, the possible influence of these muscle activities on joint movements in the takeoff leg, and their effect on the vertical and/or horizontal velocity of the jump are discussed.     

Optimal compliant-surface jumping: a multi-segment model of springboard standing jumps

A multi-segment model is used to investigate optimal compliant-surface jumping strategies and is applied to springboard standing jumps. The human model has four segments representing the feet, shanks, thighs, and trunk-head-arms. A rigid bar with a rotational spring on one end and a point mass on the other end (the tip) models the springboard. Board tip mass, length, and stiffness are functions of the fulcrum setting. Body segments and board tip are connected by frictionless hinge joints and are driven by joint torque actuators at the ankle, knee, and hip. One constant (maximum isometric torque) and three variable functions (of instantaneous joint angle, angular velocity, and activation level) determine each joint torque. Movement from a nearly straight motionless initial posture to jump takeoff is simulated. The objective is to find joint torque activation patterns during board contact so that jump height can be maximized. Minimum and maximum joint angles, rates of change of normalized activation levels, and contact duration are constrained. Optimal springboard jumping simulations can reasonably predict jumper vertical velocity and jump height. Qualitatively similar joint torque activation patterns are found over different fulcrum settings. Different from rigid-surface jumping where maximal activation is maintained until takeoff, joint activation decreases near takeoff in compliant-surface jumping. The fulcrum-height relations in experimental data were predicted by the models. However, lack of practice at non-preferred fulcrum settings might have caused less jump height than the models' prediction. Larger fulcrum numbers are beneficial for taller/heavier jumpers because they need more time to extend joints.     

Test-retest reliability of knee biomechanics during stop jump landings

Studies that seek to determine the effects of an intervention on knee biomechanics during landing from a jump implicitly assume that the variables of interest are reliable both within and between data collection sessions. Currently, such reliability data are not available for a stop jump. Standard three-dimensional motion analysis was used to determine sagittal and frontal plane peak angles and moments and peak vertical ground reaction force within and between sessions for a stop jump. Twelve female recreational athletes participated in two data collection sessions spaced two weeks apart. Interclass correlation coefficients and coefficient of multiple correlation were used to determine within and between session reliability of peak knee flexion angle, peak internal knee extension moment, peak knee abduction angle, peak internal knee adduction moment and peak vertical ground reaction force. Overall reliability within a session (ICC (3,1) 0.631-0.881; CMC 0.672-0.958) and between sessions (ICC (3,k) 0.685-0.959; CMC 0.598-0.944) was good. Peak angles and moments were similar between sessions. The stop jump is less reliable within a session than a drop vertical jump reported previously in the literature. This is likely due to increased intrasubject variability between trials due to the less constrained nature of the task. Reliability of the stop jump is comparable to the drop vertical jump between sessions. Reliability of knee adduction moment is lower than reported for the drop vertical jump. The results of this study support the use of a stop jump task to evaluate knee biomechanics during landing in longitudinal studies with a repeated measures design.     

Optimal muscular coordination strategies for jumping

This paper presents a detailed analysis of an optimal control solution to a maximum height squat jump, based upon how muscles accelerate and contribute power to the body segments during the ground contact phase of jumping. Quantitative comparisons of model and experimental results expose a proximal-to-distal sequence of muscle activation (i.e. from hip to knee to ankle). We found that the contribution of muscles dominates both the angular acceleration and the instantaneous power of the segments. However, the contributions of gravity and segmental motion are insignificant, except the latter become important during the final 10% of the jump. Vasti and gluteus maximus muscles are the major energy producers of the lower extremity. These muscles are the prime movers of the lower extremity because they dominate the angular acceleration of the hip toward extension and the instantaneous power of the trunk. In contrast, the ankle plantarflexors (soleus, gastrocnemius, and the other plantarflexors) dominate the total energy of the thigh, though these muscles also contribute appreciably to trunk power during the final 20% of the jump. Therefore, the contribution of these muscles to overall jumping performance cannot be neglected. We found that the biarticular gastrocnemius increases jump height (i.e. the net vertical displacement of the center of mass of the body from standing) by as much as 25%. However, this increase is not due to any unique biarticular action (e.g. proximal-to-distal power transfer from the knee to the ankle), since jumping performance is similar when gastrocnemius is replaced with a uniarticular ankle plantarflexor.     

Relative net vertical impulse determines jumping performance

The purpose of this investigation was to determine the relationship between relative net vertical impulse and jump height in a countermovement jump and static jump performed to varying squat depths. Ten college-aged males with 2 years of jumping experience participated in this investigation (age: 23.3 ± 1.5 years; height: 176.7 ± 4.5 cm; body mass: 84.4 ± 10.1 kg). Subjects performed a series of static jumps and countermovement jumps in a randomized fashion to a depth of 0.15, 0.30, 0.45, 0.60, and 0.75 m and a self-selected depth (static jump depth = 0.38 ± 0.08 m, countermovement jump depth = 0.49 ± 0.06 m). During the concentric phase of each jump, peak force, peak velocity, peak power, jump height, and net vertical impulse were recorded and analyzed. Net vertical impulse was divided by body mass to produce relative net vertical impulse. Increasing squat depth corresponded to a decrease in peak force and an increase in jump height and relative net vertical impulse for both static jump and countermovement jump. Across all depths, relative net vertical impulse was statistically significantly correlated to jump height in the static jump (r = .9337, p < .0001, power = 1.000) and countermovement jump (r = .925, p < .0001, power = 1.000). Across all depths, peak force was negatively correlated to jump height in the static jump (r = -0.3947, p = .0018, power = 0.8831) and countermovement jump (r = -0.4080, p = .0012, power = 0.9050). These results indicate that relative net vertical impulse can be used to assess vertical jump performance, regardless of initial squat depth, and that peak force may not be the best measure to assess vertical jump performance.     

Neuromuscular functioning of athletes and non-athletes in the drop jump

In many sports vertical jumping is important. This study compared neuromuscular functioning of the lower extremity muscles together with some kinetic and kinematic parameters before and during ground contact in drop jumps from two heights [0.4 m (DJ40) and 0.8 m (DJ80)] in 7 highly trained triple-jumpers and 11 physically active controls. The triple-jumpers jumped 32% higher in DJ40 and 34% higher in DJ80, had shorter braking and total contact times, and greater average and peak vertical ground reaction forces than the controls. In both drop jumps in the electromyogram pre-activity of the vastus lateralis and gastrocnemius muscles started earlier in the jumpers than in the controls. For the control group the increase in dropping height was associated with a decrease in the propulsion force, and resulted in more extended knee and ankle angles at touch down and more flexed angles at the deepest position than for the jumpers. All angular displacements for DJ80 were larger than for DJ40 in the control group. The triple jumpers and control subjects differed with respect to their neuromuscular functioning in the drop jump exercise and they responded in a different way to the increase in dropping height. Accepted: 2 April 1998     

Which measure of drop jump performance best predicts sprinting speed?

The purpose of this study was to evaluate which measure of a drop jump (DJ) has the highest correlation with sprinting speed over 60 m. For use of comparison, maximal leg strengths in a front squat, countermovement jump, and squat jump were also assessed. The subjects in the study were all high-caliber female university rugby players. Subjects did DJs from 0.12, 0.24, 0.36, 0.48, 0.60, 0.72, and 0.84 m. Jump height and reactive strength index (RSI) were calculated at each drop height. Pearson correlations were used to analyze the relationship between the strength and jumping measures with sprinting speed. The DJ height from 0.84 m had the highest negative correlation with 0- to 10-m split (r = -0.66), the 10- to 30-m split (r = -0.86) and 30- to 60-m split (r = -0.86). The use of RSI is questioned as a measurement of DJ performance. It is suggested that maximal height achieved in a DJ is the most important DJ measure. If it is desired to measure ground contact time, then it may be more useful to use a second test where the jump height for the athlete is set by having the athlete jump onto a box or touch a target overhead set at a standard height and measure the ground contact time with a switch mat or force plate.     

Standard anthropometric, body composition, and strength variables as predictors of jumping performance in elite junior athletes

The aim of the study was to investigate whether variables routinely assessed while testing athletes can also predict movement performance. The relation between jumping performance and standard strength, anthropometric, and body composition variables was examined in elite junior basketball players. The 33 males were tested for maximal vertical jump, as well as for maximal isometric voluntary force and rate of force development of hip and knee extensors. Standard anthropometric and body composition measures (body height, lean body mass, as well as the percentage of fat and muscle tissue) were also taken. Except for maximal isometric forces (0.38 and 0.52 N.kg(-1) for hip and knee extensors, respectively), all correlation coefficients between the selected variables and jump height were insignificant. As a consequence, the corresponding multiple correlation coefficient, R = 0.71, also suggested a moderate predictability of jumping performance by the standard strength tests and anthropometric and body composition variables. The results obtained dispute the use of the examined tests in sport performance assessment, and also question applying the tests for other purposes such as evaluation of training procedures or selection of young athletes. Therefore, the results are in line with the concept that a reliable performance assessment in homogeneous groups of athletes requires predominantly movement-specific testing.     

Relationships between force-time characteristics of the isometric midthigh pull and dynamic performance in professional rugby league players

There is considerable conflict within the literature regarding the relevance of isometric testing for the assessment of neuromuscular function within dynamic sports. The aim of this study was to determine the relationship between isometric measures of force development and dynamic performance. Thirty-nine professional rugby league players participated in this study. Forty-eight hours after trial familiarization, participants performed a maximal isometric midthigh pull, with ～120-130° bend at the knee, countermovement jump (CMJ), and a 10-m sprint. Force-time data were processed for peak force (PF), force at 100 milliseconds (F100ms), and peak rate of force development (PRFD). Analysis was carried out using Pearson's product moment correlation with significance set at p < 0.05. The PF was not related to dynamic performance; however, when expressed relative to body weight, it was significantly correlated with both 10-m time and CMJ height (r = -0.37 and 0.45, respectively, p < 0.05). The F100ms was inversely related to 10-m time (r = -0.54, p < 0.01); moreover, when expressed relative to body weight, it was significantly related to both 10-m time and CMJ height (r = -0.68 and 0.43, p < 0.01). In addition, significant correlations were found between PRFD and 10-m time (r = -0.66, p < 0.01) and CMJ height (r = 0.387, p < 0.01). In conclusion, this study provides evidence that measures of maximal strength and explosiveness from isometric force-time curves are related to jump and sprint acceleration performance in professional rugby league players.     

The evolution of jumping performance in Caribbean Anolis lizards: solutions to biomechanical trade-offs

Adaptationist theory predicts that species will evolve functional specializations for occupying different ecological niches. However, whereas performance traits are often complex, most comparative functional studies examine only simple measures of performance (e.g., sprint speed). Here we examine multiple facets of jumping biomechanics in 12 species of Caribbean Anolis lizards. These 12 species represent six ecomorphs, which are distinct ecological and morphological entities that have independently evolved on different Caribbean islands. We first show that the optimal angles for jumping maximum horizontal distances range from 39 degrees to 42 degrees, but the average jump angle of the 12 species is about 36 degrees. Interestingly, these "suboptimal" jumping angles result in only a small decrement in jump distance but substantial savings in flight duration and jump height. Further, our data show that the two key variables associated with increased jumping velocity (hindlimb length and takeoff acceleration) are independent of one another. Thus, there are two possible ways to achieve superior jumping capabilities: to evolve more muscular limbs--as stronger legs will produce more force and, hence, more acceleration--or evolve longer limbs. Our data show that anole species face trade-offs that prevent them from simultaneously optimizing different aspects of jumping ability but that they appear to have evolved behaviors that partially overcome these trade-offs.     

Muscle performance during maximal isometric and dynamic contractions is influenced by the stiffness of the tendinous structures.

Contractile force is transmitted to the skeleton through tendons and aponeuroses, and, although it is appreciated that the mechanocharacteristics of these tissues play an important role for movement performance with respect to energy storage, the association between tendon mechanical properties and the contractile muscle output during high-force movement tasks remains elusive. The purpose of the study was to investigate the relation between the mechanical properties of the connective tissue and muscle performance in maximal isometric and dynamic muscle actions. Sixteen trained men participated in the study. The mechanical properties of the vastus lateralis tendon-aponeurosis complex were assessed by ultrasonography. Maximal isometric knee extensor force and rate of torque development (RTD) were determined. Dynamic performance was assessed by maximal squat jumps and countermovement jumps on a force plate. From the vertical ground reaction force, maximal jump height, jump power, and force-/velocity-related determinants of jump performance were obtained. RTD was positively related to the stiffness of the tendinous structures (r = 0.55, P < 0.05), indicating that tendon mechanical properties may account for up to 30% of the variance in RTD. A correlation was observed between stiffness and maximal jump height in squat jumps and countermovement jumps (r = 0.64, P < 0.05 and r = 0.55, P < 0.05). Power, force, and velocity parameters obtained during the jumps were significantly correlated to tendon stiffness. These data indicate that muscle output in high-force isometric and dynamic muscle actions is positively related to the stiffness of the tendinous structures, possibly by means of a more effective force transmission from the contractile elements to the bone.     

Comparison of lower limb kinetics,kinematics and muscle activation during drop jumping under shod and barefoot conditions

This study was to investigate the acute effects of wearing shoes on lower limb kinetics, kinematics and muscle activation during a drop jump. Eighteen healthy men performed a drop jump under barefoot and shod conditions. Vertical ground reaction force (GRF) was measured on a force plate during the contact phase of a drop jump, and GRF valuables were calculated for each condition. The angles of the knee and ankle joints, and the foot strike angle (the angle between the plantar surface of the foot and the ground during ground contact) as well as the electromyography of 7 muscles were measured. The shod condition showed a significant larger first peak GRF, longer time to first peak GRF from the initial ground contact and lower initial loading rate than the barefoot condition. The shod condition showed a significant larger ankle joint angle at initial ground contact, smaller knee joint angle between the second peak GRF and take-off as well as smaller foot strike angle at both initial ground contact and take-off than the barefoot condition. There were significant correlations between relative differences in ankle joint at the initial ground contact and relative differences in the initial loading rate. The muscle activity of all muscles during foot ground contact did not differ between two conditions; however, in the shod condition, muscle activation of 150 ms before foot ground contact was significantly higher in the rectus femoris, whereas it was lower in the biceps femoris and tibialis anterior muscles than the barefoot condition. These results indicate that wearing shoes alternates the GRF variables at initial ground contact, joint kinematics at the ground contact and muscle activation before foot ground contact during a drop jump, suggesting that the effects of wearing shoes on drop jump training differ from being barefoot.     

Effect of pre-impact movement strategies on the impact forces resulting from a lateral fall

Approximately 90% of hip fractures in older adults result from falls, mostly from landing on or near the hip. A three-dimensional, 11-segment, forward dynamic biomechanical model was developed to investigate whether segment movement strategies prior to impact can affect the impact forces resulting from a lateral fall. Four different pre-impact movement strategies, with and without using the ipsilateral arm to break the fall, were implemented using paired actuators representing the agonist and antagonist muscles acting about each joint. Proportional-derivative feedback controller controlled joint angles and velocities so as to minimize risk of fracture at any of the impact sites. It was hypothesized that (a) the use of active knee, hip and arm joint torques during the pre-contact phase affects neither the whole body kinetic energy at impact nor the peak impact forces on the knee, hip or shoulder and (b) muscle strength and reaction time do not substantially affect peak impact forces. The results demonstrate that, compared with falling laterally as a rigid body, an arrest strategy that combines flexion of the lower extremities, ground contact with the side of the lower leg along with an axial rotation to progressively present the posterolateral aspects of the thigh, pelvis and then torso, can reduce the peak hip impact force by up to 56%. A 30% decline in muscle strength did not markedly affect the effectiveness of that fall strategy. However, a 300-ms delay in implementing the movement strategy inevitably caused hip impact forces consistent with fracture unless the arm was used to break the fall prior to the hip impact.     

Thigh-calf contact parameters for six high knee flexion postures: Onset,maximum angle,total force,contact area,and center of force

In high knee flexion, contact between the posterior thigh and calf is expected to decrease forces on tibiofemoral contact surfaces, therefore, thigh-calf contact needs to be thoroughly characterized to model its effect. This study measured knee angles and intersegmental contact parameters in fifty-eight young healthy participants for six common high flexion postures using motion tracking and a pressure sensor attached to the right thigh. Additionally, we introduced and assessed the reliability of a method for reducing noise in pressure sensor output. Five repetitions of two squatting, two kneeling, and two unilateral kneeling movements were completed. Interactions of posture by sex occurred for thigh-calf and heel-gluteal center of force, and thigh-calf contact area. Center of force in thigh-calf regions was farther from the knee joint center in females, compared to males, during unilateral kneeling (82 and 67 mm respectively) with an inverted relationship in the heel-gluteal region (331 and 345 mm respectively), although caution is advised when generalizing these findings from a young, relatively fit sample to a population level. Contact area was larger in females when compared to males (mean of 155.61 and 137.33 cm² across postures). A posture main effect was observed in contact force and sex main effects were present in onset and max angle. Males had earlier onset (121.0°) and lower max angle (147.4°) with onset and max angles having a range between movements of 8° and 3° respectively. There was a substantial total force difference of 139 N between the largest and smallest activity means. Force parameters measured in this study suggest that knee joint contact models need to incorporate activity-specific parameters when estimating loading.     

Alterations to movement mechanics can greatly reduce anterior cruciate ligament loading without reducing performance

Anterior cruciate ligament (ACL) injuries are one of the most common and potentially debilitating sports injuries. Approximately 70% of ACL injuries occur without contact and are believed to be preventable. Jump stop movements are associated with many non-contact ACL injuries. It was hypothesized that an athlete performing a jump stop movement can reduce their peak tibial shear force (PTSF), a measure of ACL loading, without compromising performance, by modifying their knee flexion angle, shank angle, and foot contact location during landing. PTSF was calculated for fourteen female basketball players performing jump stops using their normal mechanics and mechanics modified to increase their knee flexion angle, decrease their shank angle relative to vertical and land more on their toes during landing. Every subject tested experienced drastic reductions in their PTSF (average reduction=56.4%) using modified movement mechanics. The athletes maintained or improved their jump height with the modified movement mechanics (an average increase in jump height of 2.5 cm). The hypothesis was supported: modifications to jump stop movement mechanics greatly reduced PTSF and therefore ACL loading without compromising performance. The results from this study identify crucial biomechanical quantities that athletes can easily modify to reduce ACL loading and therefore should be targeted in any physical activity training programs designed to reduce non-contact ACL injuries.     

Jumping height in former elite athletes

To evaluate lower-limb explosive strength with respect to lifetime athletic activity, we measured vertical jumping height on a contact mat in former male runners (n = 28). soccer players (n = 31), weightlifters (n = 29) and shooters (n = 29) (age range 45 68 years). There were no statistically significant age-adjusted sport-group differences in jumping height, but differences by sport were evident among the subgroup of athletes without hip or knee osteoarthritis (n = 65) (P < 0.05). Thus, sports that increased jumping height also predisposed to lower-limb osteoarthritis. After adjustment for age and sport, the subjects without osteoarthritis jumped higher than those with osteoarthritis (n = 33) (P < 0.01). In a multiple linear regression analysis, age, reported hip and knee disability, and knee pain reduced jumping height. Hours spent in team-training during the past 12 months and the hours spent during their lifetime in power training were associated with improved vertical jumping height and together explained 41% of the difference among the subjects. The ability to jump even among athletes with hip or knee osteoarthritis would suggest that former elite athletes possess advanced lower limb muscle function.