Use of a newly developed rapid microbial ATP bioluminescence assay to detect microbial contamination on poultry carcasses

A newly developed rapid microbial ATP bioluminescence test (R-mATP) was shown to be an adequate means to assay the microbial load of poultry carcasses. This assay utilizes differential extraction and filtration to separate somatic from microbial ATP in a very rapid timeframe. The assay requires approximately 5 min to complete; approximately 3.5 min to sample and 90 s analytical time. Correlation coefficient (r) between aerobic colony counts and R-mATP test results (n=329) was 0.82. Post-test probabilities to correctly classify carcasses with different levels of microbial contamination were as high as 98% for samples of ≥3.5 log aerobic CFU per ml. Given the rapidity of this assay, the R-mATP holds potential for monitoring the microbial load of carcasses at poultry-processing critical control points. Other potential applications of this new version of the microbial ATP bioluminescence test are discussed.     

Use of ATP bioluminescence measurements for the estimation of biomass during biological humification

Summary The development of the microflora during the humification of grape pulp has been investigated by the determination of ATP using the bioluminescence technique. Several extraction methods were tested including the use of dimethylsulphoxide, trichloroacetic acid, grinding and ultrasonification. Dimethylsulphoxide and ultrasonification for 15 sec appeared to be the most effective. The ATP extract was stabilized when it was mixed with 0.75 mM glycine, 4.4 mM Mg-EDTA, pH 7.5 and frozen. The relative error of the ATP assay by bioluminescence did not exceed 6.5%. This method allowed us to show that at least five distinct reproducible microbial phases exist during grape pulp humification. These results show that the microbial biomass changes noticeably and at distinct times during composting.     

EVALUATION OF ADENOSINE TRIPHOSPHATE (ATP) BIOLUMINESCENCE FOR ESTIMATING BACTERIA ON SURFACES OF BEEF CARCASSES

A rapid (<15 min), inexpensive and simple method has been developed to estimate the concentration of bacteria on surfaces of beef carcasses using adenosine triphosphate (ATP) bioluminescence. Surfaces (5x5 cm²) of beef carcasses (n= 159) were collected by excision. An ATP assay and aerobic plate count were performed on each sample. A significant (p < 0.001) positive linear relationship (r = 0.83) between plate count and ATP assay was obtained for 159 beef carcass samples. When thresholds levels were set at 1 × 10⁴, 1 × 10⁵ and 1 × 10⁶ CFU/cm², there was moderate to good agreement between the ATP bioluminescence assay and the aerobic plate count as determined by the k-statistic. The application of this ATP bioluminescence test to HACCP systems for beef slaughter processes is discussed.     

不同方法检测鸡蛋表面菌落总数的相关性研究

研究了ATP生物荧光检测法与国标法《GB4789.2-2010食品卫生微生物学检验菌落总数测定》检测鸡蛋壳表面细菌总数的相关性。采用ATP生物荧光检测法和国标法对40个混合样品表面细菌总数进行检测,以log CFU/个蛋壳为横坐标(x),以logRLU/个蛋壳为纵坐标(y),分别进行线性、对数、乘幂、指数拟合。结果表明,ATP荧光检测法与国标法检测结果 Pearson相关系数为0.912,线性模型y=0.7306x-1.0041(R2=0.8322)拟合度较高。该试验结果为ATP荧光检测法在鸡蛋壳表面细菌总数快速检测中应用的可行性提供了依据。     

基于ATP生物发光法的微生物数量快速检测技术的研究进展

微生物数量的快速检测一直是工业生产与食品行业需要解决的问题,腺嘌呤核苷三磷酸(adenosine triphosphate,ATP)生物发光法具有操作简便、检测周期短等优点,可满足一般微生物检测的需求。然而,ATP生物发光法的准确性也受到不同因素的影响,如微生物的ATP检测限值较高、微生物自身及其他因素(如非微生物ATP、提取剂种类、荧光素酶活性等)均对微生物数量的检测产生影响。本文简述了不同微生物数量检测方法的优缺点,介绍了ATP生物发光法的发展历程及原理,综述了非微生物ATP与游离ATP、微生物量、ATP提取剂、荧光素酶等因素对ATP生物发光法灵敏度与稳定性的影响,归纳总结了ATP生物发光法及检测设备在食品、医疗、污水处理等领域的应用现状,并就ATP生物发光法体系的优化及ATP在线检测的应用等方面进行了展望,以期为ATP生物发光法的高效应用提供新的思路。     

An ATP Bioluminescence Assay Applicable to Rapid Fluconazole Susceptibility Testing of Dermatophytes

An ATP bioluminescence assay as a rapid reference method for fluconazole (FLCZ) susceptibility testing of dermatophytes, as well as yeasts, was developed and evaluated by comparing it with viability, turbidity and fungal protein content-based conventional methods. FLCZ susceptibility results obtained with strains of Candida albicans and dermatophytes by the bioluminescence method in high-resolution medium were well correlated with those obtained by conventional methods currently used in clinical microbiology laboratories or reported previously, including a broth dilution method by the National Committee for Clinical Laboratory Standards (NCCLS). Thus, ATP bioluminescence assay can be used to monitor fungal growth in liquid culture media. The procedure has considerable potential for the rapid testing of FLCZ susceptibility of dermatophytes and other fungi.     

ATP bioluminescence rapid detection of total viable count in soy sauce

The adenosine triphosphate (ATP) bioluminescence rapid determination method may be useful for enumerating the total viable count (TVC) in soy sauce, as it has been previously used in food and beverages for sanitation with good precision. However, many factors interfere with the correlation between total aerobic plate counts and ATP bioluminescence. This study investigated these interfering factors, including ingredients of soy sauce and bacteria at different physiological stages. Using the ATP bioluminescence method, TVC was obtained within 4 h, compared to 48 h required for the conventional aerobic plate count (APC) method. Our results also indicated a high correlation coefficient (r = 0.90) between total aerobic plate counts and ATP bioluminescence after filtration and resuscitation with special medium. The limit of quantification of the novel detection method is 100 CFU/mL; there is a good linear correlation between the bioluminescence intensity and TVC in soy sauce in the range 1 × 10²–3 × 10⁴ CFU/mL and even wider. The method employed a luminescence recorder (Tristar LB‐941) and 96‐well plates and could analyse 50–100 samples simultaneously at low cost. In this study, we evaluated and eliminated the interfering factors and made the ATP bioluminescence rapid method available for enumerating TVC in soy sauce. Copyright © 2011 John Wiley & Sons, Ltd.     

ATP amplification for ultrasensitive bioluminescence assay: detection of a single bacterial cell

We developed an ultrasensitive bioluminescence assay of ATP by employing (i) adenylate kinase (ADK) for converting AMP + ATP to two molecules of ADP, (ii) polyphosphate (polyP) kinase (PPK) for converting ADP back to ATP (ATP amplification), and (iii) a commercially available firefly luciferase. A highly purified PPK-ADK fusion protein efficiently amplified ATP, resulting in high levels of bioluminescence in the firefly luciferase reaction. The present method, which was approximately 10,000-fold more sensitive to ATP than the conventional bioluminescence assay, allowed us to detect bacterial contamination as low as one colony-forming unit (CFU) of Escherichia coli per assay.     

Application of a bioluminescence ATP assay in brewery wastewater treatment studies

The importance of having a rapid method for determining the viable biomass in activated-sludge wastewater treatment plants (WWTP) for process control and development is well recognized. The firefly bioluminescence ATP assay has been proposed for this purpose. Such an assay using partially purified firefly luciferase and synthetic firefly luciferin for the bioluminescence reaction, a liquid scintillation counter in the out-of-coincidence mode as luminescence detector, and a sludge ATP extraction technique involving dimethyl sulfoxide at room temperature is described. Experiments with several pure bacteria cultures were done to demonstrate the feasibility of applying this assay to activated sludge to activated sludge WWTP investigation and control. The ATP content of samples taken from various points in a 350000 gal/day brewery activated-sludge WWTP was monitored for 4.5 months. Good linear correlation between ATP and mixed-liquor suspended solids, return sludge suspended solids, and effluent suspended solids were observed. Percentage viabilities of the various sludge samples were derived from the ATP results.     

利用ATP扩增反应与生物发光法结合检测微量微生物

摘要:【目的】腺苷酸激酶（adenylate kinase, ADK）和多聚磷酸盐激酶（polyphosphate kinase, PPK）偶联催化的ATP扩增反应结合生物发光检测法能够对微量微生物进行检测。但是PPK当中结合的内源性的ADP会产生背景干扰,影响测定。本文旨在融合表达ADK和PPK,并建立一种方便有效的内源性ADP的去除方法,降低背景,使之与传统生物发光法结合,实现高灵敏生物发光法检测微量ATP及微生物。【方法】PCR扩增得到PPK、ADK基因,插入表达载体pET28a (+)中构建重组表达质粒pET28a (+)-PPKADK,表达PPK-ADK融合蛋白。利用表面包裹聚胺醇（Polyurethane）的磁珠（magnetic beads）,通过化学反应将腺苷酸双磷酸酶（apyrase）固定于磁珠表面,制备固相腺苷酸双磷酸酶（Beads-apyrase）,用于除去与融合蛋白结合的内源性ADP,降低ATP扩增反应的背景,从而使之与生物发光反应相结合,测定微量外源ATP及细菌菌落数。【结果】表达的融合蛋白具有PPK和ADK的活性,利用Beads-apyrase可以方便而有效的去除内源性ADP,显著地降低反应背景,从而实现了利用ATP扩增反应与传统生物发光反应结合,测定了小于1 fmol的外源微量ATP,使生物发光法检测ATP及微生物的灵敏度提高至少100倍。【结论】利用Beads-apyrase能够方便、有效地降低PPK-ADK中的ADP背景,从而使PPK-ADK催化的ATP扩增反应能够与传统生物发光法相结合,极大地提高了生物发光法的灵敏度。     

Fast Monitoring of Indoor Bioaerosol Concentrations with ATP Bioluminescence Assay Using an Electrostatic Rod-Type Sampler

A culture-based colony counting method is the most widely used analytical technique for monitoring bioaerosols in both indoor and outdoor environments. However, this method requires several days for colony formation. In this study, our goal was fast monitoring (Sampling: 3 min, Detection: < 1 min) of indoor bioaerosol concentrations with ATP bioluminescence assay using a bioaerosol sampler. For this purpose, a novel hand-held electrostatic rod-type sampler (110 mm wide, 115 mm long, and 200 mm tall) was developed and used with a commercial luminometer, which employs the Adenosine triphosphate (ATP) bioluminescence method. The sampler consisted of a wire-rod type charger and a cylindrical collector, and was operated with an applied voltage of 4.5 kV and a sampling flow rate of 150.7 lpm. Its performance was tested using Staphylococcus epidermidis which was aerosolized with an atomizer. Bioaerosol concentrations were measured using ATP bioluminescence method with our sampler and compared with the culture-based method using Andersen cascade impactor under controlled laboratory conditions. Indoor bioaerosol concentrations were also measured using both methods in various indoor environments. A linear correlation was obtained between both methods in lab-tests and field-tests. Our proposed sampler with ATP bioluminescence method may be effective for fast monitoring of indoor bioaerosol concentrations.     

ATP as a biomarker of viable microorganisms in clean-room facilities

A new firefly luciferase bioluminescence assay method that differentiates free extracellular ATP (dead cells, etc.) from intracellular ATP (viable microbes) was used to determine the viable microbial cleanliness of various clean-room facilities. For comparison, samples were taken from both clean-rooms, where the air was filtered to remove particles >0.5 microm, and ordinary rooms with unfiltered air. The intracellular ATP was determined after enzymatically degrading the sample's free ATP. Also for comparison, cultivable microbial populations were counted on nutrient-rich trypticase soy agar (TSA) plates. Both the cultivable and ATP-based determinations indicate that the microbial burden was lower in clean-room facilities than in ordinary rooms. However, there was no direct correlation between the two sets of measurements because the two assays measured very different populations. A large fraction of the samples yielded no colony formers on TSA, but were positive for intracellular ATP. Subsequently, genomic DNA was isolated directly from selected samples and 16S rDNA fragments were cloned and sequenced, identifying nearest neighbors, many of which are known to be noncultivable in the media employed. It was concluded that viable microbial contamination can be reliably monitored by measurement of intracellular ATP, and that this method may be considered superior to cultivable colony counts due to its speed and its ability to report the presence of viable but noncultivable organisms. When the detection of nonviable microbes is of interest, the ATP assay can be supplemented with DNA analysis.     

The effects of short-term training on platelet functions and total antioxidant capacity in rats

The purpose of the present study was to investigate the effect of short-term endurance training on plasma total antioxidant status (TAS) and on in vitro platelet aggregation and ATP release. Blood samples were collected from the abdominal aorta of rats following short-term treadmill exercise (25 m/min, 0 % grade, 30 min) for three consecutive days, as well as in non-exercised control group. Platelet aggregation and platelet ATP release were evaluated by impedance and bioluminescence techniques, respectively. Plasma TAS was measured spectrophotometrically. Plasma TAS was higher and ADP-induced platelet ATP release was lower in the short-term training group with respect to the control group (p<0.001). Significant negative correlation (r = -0.56, p<0.05) was found between plasma TAS and ADP-induced platelet ATP release. Neither ADP- and collagen-induced maximum aggregation rate nor collagen-induced platelet ATP release were significantly different between the groups. According to these results, short-term training caused an alteration in platelet functions limited to the secretion response, which may be related to the oxidant/antioxidant balance changes favoring the antioxidants. The improved plasma total antioxidant capacity was possibly sufficient to prevent exercise-induced oxidative damage, and the adaptive response of platelets might be associated with enhanced antioxidant status.     

Rapid separation and quantitation of mixed microorganisms by filtration and bioluminescence

A membrane filtration/bioluminescence system was developed for the differentiation and quantitation of mixed populations of microorganisms. Samples containing microorganisms were filtered through two membrane filters of descending pore size. The microorganisms retained on the filter contain ATP that can be extracted and measured on the filter via the firefly luciferase-luciferin bioluminescence assay. Results, obtained in less than 20 min, show a good correlation (r greater than or equal to 0.95) between the light produced and the number of organisms in the sample. Using these techniques, Escherichia coli can be separated from yeast or mold and measured in samples containing both microorganisms. When lysostaphin is used to selectively lyse Staphylococci on the filter, the specific quantification of these bacteria among other microorganisms can also be accomplished. The filtration/bioluminescence technique offers the potential of being a rapid and sensitive method to differentiate and detect microorganisms, by selective sizing or lysing, in a variety of samples.     

Intracellular adenosine triphosphate as a measure of human tumor cell viability and drug modulated growth

Summary Adenosine triphosphate is the primary energy unit for cells, and levels of this compound offer a potential marker for cell viability and growth. The availability of a bioluminescence assay allows for a rapid, sensitive, and reproducible measurement of ATP. A method is described for the quantification of intracellular ATP levels in human cancer cells. ATP levels were linearly related to the number of viable cells and increased with time in human cancer cell line cultures correlating with growth kinetics. The effect of 5-fluorouracil, doxorubicin, methotrexate, cytosine arabinoside, nitrogen mustard, melphalan, vinblastine, and cisplatin on the growth of human cancer cell lines was studied utilizing ATP levels. ATP levels and colony formation in agar of drug-exposed cells were compared. Overall there was a significant correlation between drug effects on colony formation and ATP levels. The ATP assay is rapid, simple, reproducible, and a relatively inexpensive method of quantifying drug effects on malignant cells. This makes it a potentially useful method for screening new anticancer drugs in human cancer cell lines.     

A convenient one-step extraction of cellular ATP using boiling water for the luciferin-luciferase assay of ATP

Cellular ATP is commonly determined as production of bioluminescence using a luciferin-luciferase reaction system. Before the measurement of bioluminescence, cellular ATP must first be extracted. Two commonly used extraction methods are: () Tris-borate buffer (pH 9.2) coupled with a heating process (to inactivate ATPase) and () perchloric acid followed by neutralization. However, we found that both Tris-borate buffer and perchloric acid interfered with the luciferin-luciferase system. Here, we report a convenient single-step boiling deionized water (DW) method for extracting cellular ATP to replace perchloric acid and Tris-borate buffer. We showed that the boiling DW method did not interfere with the bioluminescence and was effective in inhibiting ATPase. This improved method required no neutralization and dilution and thus was more convenient than the perchloric acid method. Unlike the Tris-borate/heating procedure, our method did not require a separate heating step because boiling DW effectively inhibited ATPase and thus accomplished the two missions in one step for both suspended and attached cells. The improved method was precise for both suspended cells and attached cells, when cell numbers were between 10(3) and 10(6). The method also was more sensitive than other methods because it required much fewer cells (10(4) to 10(5)) than other methods for ATP determination. Thus, this one-step method is suitable for routine assay of cellular ATP for both suspended and attached cells.     

两种萤火虫荧光素酶活性检测方法的一致性比较

目的：比较2种萤火虫荧光素酶活性检测方法的一致性。方法：分别采用化学发光技术（Che）及活体光学成像技术（Bio）,从细胞和动物水平检测在转染以萤火虫荧光素酶为报告基因的载体pCI-AAA-Fluc-neo后不同时间点,萤火虫荧光素酶的表达强度。结果：在细胞和动物水平,萤火虫荧光素酶的表达强度均随时间推移逐步递减。在HepG2细胞,萤火虫荧光素酶表达持续96h,活性从24h的2781±220mV（1．6×10^6±2．3×10^5光子）降至96h的49±3．5mV（6．4×10^4±2．5×10^4光子）。在动物水平得到相似的结果,BALB／c小鼠萤火虫荧光素酶表达持续20d,其活性从1d的16592±409mV（1．9×10^8±3．6×10^6光子）降至20d的798±139mV（3．37×10^5±3．8×10^4光子）。通过一致性检验,2种检测方法在细胞和动物水平的直线回归方程分别为lgChe=1．186·lgBio-3．764（r=-0．937,P〈0．001）和lgChe=0．451·lgBio＋0．64（r=0．915,P〈0．001）;进一步将理论数据与实验数据进行配对t检验,二者无统计学差异（P〉0．05）。结论：2种检测方法是一致的;从整个实验过程来看,活体光学成像技术较化学发光法更为简便、直观,可量化地对同一个体连续检测,减少了个体间差异和实验动物用量。     

The enumeration of Leptospira interrogans serovar pomona by a bioluminescence ATP assay

A rapid method for enumerating viable Leptospira interrogans serovar pomona cells was investigated using a bacterial adenosine triphosphate (ATP) assay. The ATP was assayed by the luciferin-luciferase bioluminescence reaction. Samples of serovar pomona grown in liquid polysorbate 80-bovine albumin (P80-BA) medium for 1-3 days were analysed for ATP content, culture density (nephelometry), direct cell count and most probable number of viable cells (MPNVC) as determined by the dilution tube technique. A linear relationship was found between ATP content and the number of viable cells over the range of 4 X 10(8) to 8 X 10(9) leptospires/ml. Over this range the correlation coefficient for ATP content versus viable cells (0.96) was similar to the coefficient for culture density versus the number of viable cells. The coefficient for direct counts versus the number of viable cells was smaller. The bioluminescence assay of bacterial ATP is a promising method for enumerating viable leptospires in pure culture.     

饮用水微生物的安全快速检测

【目的】为了更好地分析饮用水中的微生物含量。【方法】利用流式细胞术(Flowcytometry,FCM)、ATP测定方法检测瓶装无气饮用水中的微生物数量、可同化有机碳(Assimilable organic carbon,AOC)含量以及微生物活性,并将检测结果与传统的饮用水微生物检测技术相对照。【结果】FCM方法可快速区分水样中的活性细菌和非活性细菌,AOC含量反映了水样中微生物再生能力;而ATP检测方法也能比异养细菌平板计数法(Heterotrophic plate count,HPC)更好地反映瓶装无气饮用水中的实际微生物含量。【结论】FCM、ATP测定方法要明显优于依赖于培养的传统方法。     

Development of a biosensor for on-line detection of tributyltin with a recombinant bioluminescent Escherichia coli strain

A biosensor was developed for the detection of tributyltin (TBT), using a bioluminescent recombinant Escherichia coli:: luxAB strain. Dedicated devices allowed the on-line measurement of bioluminescence, pH and dissolved oxygen values and the feed-back regulation of temperature. Bacterial physiology was monitored by the measurement of the cellular density, respiratory activity and the intracellular level of ATP, glucose and acetate levels. Our results showed that a synthetic glucose medium gave a better TBT detection limit than LB medium (respectively 0.02 micro M and 1.5 micro M TBT). High growth and dilution rates ( D=0.9 h(-1)) allowed maximum light emission from the bacterium. Moreover, simple atmospheric air bubbling was sufficient to provide oxygen for growth and the bioluminescence reaction. Real-time monitoring of bioluminescence after TBT induction occurred with continuous addition of decanal up to 300 micro M, which was not toxic throughout a 7-day experiment. The design of our biosensor and the optimization of the main parameters that influence microbial activity led to the capacity for the detection of TBT.