The adhesion of thin carbon films to metallic substrates.

As part of the development of carbon-coated prosthetic devices, the adhesion of thin carbon films to metallic substrates has been studied. The bond strength of carbon films about 5000 A thick on Ti-6A1-4V and stainless steel was measured in a pull test and found to be greater than 4700 psi. Auger electron spectroscopy showed a reactive film/substrate interface. The ultimate bond strength was found to be dependent on the substrate and the deposition parameters.     

Properties and microstructure of thermo-pressed wheat gluten films: a comparison with cast films

Wheat gluten films were prepared by thermo-pressing, and their mechanical properties were compared to those of cast films. The stress-strain relationship was established for films with various amounts of glycerol. Both relationships were quite different, revealing a different network organization. Thermo-pressed films presented higher stress values than cast films, but the effect of the glycerol amount was similar in both cases, an increase of the glycerol amount leading to a decrease of both films stress. The glycerol influence on the strain at break of thermo-pressed films was very limited, with strain values reaching a maximum around 200%. The role of disulfide bridges on themomoulded films mechanical properties was investigated, and it was shown that some rearrangements and a significative protein insolubilization occurred during the process. The effective flow porosity of the protein network for thermo-pressed films was estimated by water capillary rise measurements to about 7%. Scanning electron microscopy was used to obtain some information about the microstructure of both cast and thermo-pressed films.     

On the unique isotropic aragonitic tube microstructure of some serpulids (Polychaeta,Annelida)

A Scanning electron microscopy study of peculiar serpulid tube microstructures was carried out to determine whether this structure is unique to serpulids and to understand its formation and evolution. The isotropic aragonitic tube microstructure of some serpulids, termed spherulitic irregularly oriented prismatic structure (SIOP), is unknown in other animal skeletons. After nucleation, initial spherulitic prismatic aragonite crystals presumably grow in length and width at one end, collide with the surrounding growing crystal fans, and then continue intertwined growth until the secreted carbonate‐charged mucus is completely crystallized. Spherulitic irregularly oriented prismati structure presumably evolved either from the IOP or homogeneous rounded crystal microstructures. J. Morphol., 2013. © 2012 Wiley Periodicals, Inc.     

The surface of evaporated carbon films is an insulating, high-bandgap material

The electrical conductance and the optical density of evaporated carbon films are measured as a function of the thickness of the films. The resulting data show that up to a thickness of approximately 4 nm, carbon films are optically transparent and electrically insulating. The same data also suggest that this insulating character persists near to the surface when the overall thickness is further increased. Since a support film with poor surface conductivity is undesirable for many applications in electron microscopy, we suggest that the usefulness of evaporated carbon films in electron microscopy might be further improved by doping or by other methods that improve the electrical conductivity near the surface.     

Physical properties of emulsion-based hydroxypropyl methylcellulose films: Effect of their microstructure

The initial characteristics of emulsions and the rearrangement of the oil droplets in the film matrix during film drying, which defines its microstructure, has an important role in the physical properties of the emulsion-based films. The objective of this work was to study the effect of the microstructure (two droplet size distributions) and stability (with or without surfactant) of HPMC oil-in-water emulsions over physical properties of HPMC emulsion-based edible films. HPMC was used to prepare sunflower oil-in-water emulsions containing 0.3 or 1.0% (w/w) of oil with or without SDS, as surfactant, using an ultrasonic homogenizer. Microstructure, rheological properties and stability of emulsions (creaming) were measured. In addition, microstructure, coalescence of oil droplets, surface free energy, optical and mechanical properties and water vapor transfer of HPMC films were evaluated. Image analysis did not show differences among droplet size distributions of emulsions prepared at different oil contents; however, by using SDS the droplet size distributions were shifted to lower values. Volume mean diameters were 3.79 and 3.77μm for emulsions containing 0.3 and 1.0% without surfactant, respectively, and 2.72 and 2.71μm for emulsions with SDS. Emulsions formulated with 1.0% of oil presented higher stability, with almost no change during 5 and 3 days of storage, for emulsions with and without SDS, respectively. Internal and surface microstructure of emulsion-based films was influenced by the degree of coalescence and creaming of the oil droplets. No effect of microstructure over the surface free energy of films was found. The incorporation of oil impaired the optical properties of films due to light scattering of light. Addition of oil and SDS decreased the stress at break of the emulsion-based films. The replace of HPMC by oil and SDS produce a lower "amount" of network structure in the films, leading to a weakening of their structure. The oil content and SDS addition had an effect over the microstructure and physical properties of HPMC-based emulsions which lead to different microstructures during film formation. The way that oil droplets were structured into the film had an enormous influence over the physical properties of HPMC films.     

The effect of metal microstructure on the initial attachment of Escherichia coli to 1010 carbon steel

Metallurgical features have been shown to play an important role in the attachment of microorganisms to metal surfaces. In the present study, the influence of the microstructure of as-received (AR) and heat-treated (HT) 1010 carbon steel on the initial attachment of bacteria was investigated. Heat treatment was carried out with the aim of increasing the grain size of the carbon steel coupons. Mirror-polished carbon steel coupons were immersed in a minimal medium inoculated with Escherichia coli (ATCC 25922) to investigate the early (15, 30 and 60?min) and relatively longer-term (4?h) stages of bacterial attachment. The results showed preferential colonisation of bacteria on the grain boundaries of the steel coupons. The bacterial attachment to AR steel coupons was relatively uniform compared to the HT steel coupons where an increased number of localised aggregates of bacteria were found. Quantitative analysis showed that the ratio of the total number of isolated (ie single) bacteria to the number of bacteria in aggregates was significantly higher on the AR coupons than the HT coupons. Longer-term immersion studies showed production of extracellular polymeric substances by the bacteria and corrosion at the grain boundaries on both types of steel coupon tested.     

Chemically functionalized carbon films for single molecule imaging

Many biological complexes are naturally low in abundance and pose a significant challenge to their structural and functional studies. Here we describe a new method that utilizes strong oxidation and chemical linkage to introduce a high density of bioactive ligands onto nanometer-thick carbon films and enable selective enrichment of individual macromolecular complexes at subnanogram levels. The introduced ligands are physically separated. Ni-NTA, Protein G and DNA/RNA oligonucleotides were covalently linked to the carbon surface. They embody negligible mass and their stability makes the functionalized films able to survive long-term storage and tolerate variations in pH, temperature, salts, detergents, and solvents. We demonstrated the application of the new method to the electron microscopic imaging of the substrate-bound C3PO, an RNA-processing enzyme important for the RNA interference pathway. On the ssRNA-linked carbon surface, the formation of C3PO oligomers at subnanomolar concentrations likely mimics their assembly onto ssRNA substrates presented by their native partners. Interestingly, the 3D reconstructions by negative stain EM reveal a side port in the C3PO/ssRNA complex, and the 15 Å cryoEM map showed extra density right above the side port, which probably represents the ssRNA. These results suggest a new way for ssRNAs to interact with the active sites of the complex. Together our data demonstrate that the surface-engineered carbon films are suitable for selectively enriching low-abundance biological complexes at nanomolar level and for developing novel applications on a large number of surface-presented molecules.     

Relative permeabilities of plastic films to water and carbon dioxide

The permeabilities of several types of plastic films to water and to carbon dioxide were measured. No material was found to have a carbon dioxide permeability as great as its water permeability.     

Electrochemical investigations of cholesterol enriched glassy carbon supported thin lipid films

The formation and study of stable cholesterol enriched thin lipid layers onto the surface of glassy carbon electrode is reported in this work. The method of formation relies on additional thinning of wetting films by electrostriction. Electrochemical techniques based on the concepts of impedance and voltammetry are used to explore the films' features. The impedance data reveal a substantial change of relaxation characteristics of the modified films. In this respect, opportunities for the evaluation of the films' stage based on the approximation with 'constant phase angle element' are discussed. The possible final structure of the films, as well as, their relevance for development of sensor elements are briefly viewed.     

The bone tissue of the canine mandible is elastically isotropic

This paper reports experimental measurements which show that canine mandibular bone tissue is elastically isotropic. Earlier work has established that human, canine and bovine cortical bone tissue of the femur, tibia and skull are elastically anisotropic and therefore the reported isotropy of mandibular tissue was unexpected. The isotropic elastic moduli of the canine mandible are represented by a Young's modulus of 7.5 GPa and a Poisson's ratio of 0.4. Earlier work gave the three orthotropic Young's moduli of the cortical one of the canine femur as 12.8 GPa, 15.6 GPa and 20.1 GPa. The experimental technique employed is elastic wave propagation at ultrasonic frequencies.     

The radiation crosslinked films based on PLLA/PDLA stereocomplex after TAIC absorption in supercritical carbon dioxide

The absorption of triallyl isocyanurate (TAIC) to equimolar stereo blends of PLLA and PDLA (sb-PLA samples) with crosslinker (TAIC) was controlled by supercritical carbon dioxide (sc-CO₂) treatment. The well-mixed sb-PLA/TAIC (sc-PLA) samples containing certain ratios of TAIC were obtained after vacuum evaporation. The sc-PLA samples were become much softer by sc-CO₂ treatment. The crosslinked sc-PLA materials with different crosslinking density were prepared by irradiation treatment at different radiation doses. Gel fraction, thermal properties and mechanical properties of crosslinked samples were investigated with different sc-PLA samples irradiated at the same radiation dose of 30 kGy and sc-PLA3 irradiated at different radiation doses. The crosslinking network inhibited crystallization, and enhanced the rigidity as well as lowered brittleness of irradiated samples. Although tensile strength and Young’s modulus of sc-PLA are reduced by sc-CO₂ treatment, they are much improved by radiation crosslinking at a suitable dose and the crosslinked samples become harder and tougher. The typical crosslinked obtained from sc-PLA3 irradiated at 30 kGy reveals the best thermal stability with the improved mechanical properties.     

The evolution of dinosaur tooth enamel microstructure

The evolution of tooth enamel microstructure in both extinct and extant mammalian groups has been extensively documented, but is poorly known in reptiles, including dinosaurs. Previous intensive sampling of dinosaur tooth enamel microstructure revealed that: (1) the three‐dimensional arrangement of enamel types and features within a tooth—the schmelzmuster—is most useful in diagnosing dinosaur clades at or around the family level; (2) enamel microstructure complexity is correlated with tooth morphology complexity and not necessarily with phylogenetic position; and (3) there is a large amount of homoplasy within Theropoda but much less within Ornithischia. In this study, the examination of the enamel microstructure of 28 additional dinosaur taxa fills in taxonomic gaps of previous studies and reinforces the aforementioned conclusions. Additionally, these new specimens reveal that within clades such as Sauropodomorpha, Neotheropoda, and Euornithopoda, the more basal taxa have simpler enamel that is a precursor to the more complex enamel of more derived taxa and that schmelzmusters evolve in a stepwise fashion. In the particularly well‐sampled clade of Euornithopoda, correlations between the evolution of dental and enamel characters could be drawn. The ancestral schmelzmuster for Genasauria remains ambiguous due to the dearth of basal ornithischian teeth available for study. These new specimens provide new insights into the evolution of tooth enamel microstructure in dinosaurs, emphasizing the importance of thorough sampling within broadly inclusive clades, especially among their more basal members.     

The significance of bone microstructure in mechanotransduction

Recent developments in modeling the relationship between bone microstructure and mechanotransduction are reviewed. The focus is on the relationship between the bone microstructure and the mechanosensation mechanism by which osteocytes sense the bone fluid motion propelled by the mechanical loading of the whole bone.