Fabrication and characterization of non-enzymatic glucose sensor based on ternary NiO/CuO/polyaniline nanocomposite

Novel nickel and copper oxide nanoparticle modified polyaniline (PANI) nanofibers (NiO/CuO/PANI) were fabricated and used as a non-enzymatic sensor for detecting glucose. PANI nanofibers were prepared through electrodeposition, whereas nickel and copper oxide nanoparticles were deposited on PANI nanofibers by electrodeposition and electrochemical oxidation in situ. The morphology and structure of NiO/CuO/PANI nanocomposites were characterized by field emission scanning electron microscopy (FE–SEM), X-ray diffraction (XRD), Raman spectroscopy, and Fourier transform infrared (FT–IR). The as-prepared NiO/CuO/PANI electrode was employed for non-enzymatic glucose detection in alkaline electrolyte and showed better electrocatalytic activity compared with the PANI, CuO/PANI, and NiO/PANI electrodes. Consequently, an amperometric electrode of glucose was achieved under 0.6 V versus Ag/AgCl with a wide linear range from 20 to 2500 μM (R² = 0.9978) and a low detection limit of 2.0 μM (signal/noise [S/N] = 3). This electrode can effectively analyze glucose concentration in human serum samples, avoiding interference, and is a promising non-enzymatic glucose sensor due to its low overpotential, high sensitivity, good selectivity and stability, fast response, and low cost.     

Polyaniline grafted polyacylonitrile conductive composite fibers for reversible immobilization of enzymes: Stability and catalytic properties of invertase

Polyacylonitrile fibers (PAN) surfaces were modified with chemical polymerization of conductive polyaniline (PANI) in the presence of potassium dichromate as an oxidizing agent. The effect of aniline concentration on the grafting efficiency and on the electrical surface resistance of PAN/PANI composite fibers was investigated. The surface resistance of the conductive composite fibers in this work was found to be between 8.0 and 0.5 kΩ/cm. As the amount of grafted PANI increased on the PAN fibers the electrical resistance of composite fibers decreased. The PAN/PANI composite fibers were characterized by SEM and FTIR studies. Composite PAN/PANI fibers were used for reversible immobilization of invertase. The immobilization efficiency and the activity of the immobilized invertase (from 1.0 mg/mL invertase solution at pH 5.5) were increased with increasing PANI contents of the composite fibers. The maximum amount of immobilized enzyme onto composite fibers containing 2.0% PANI was about 76.6 mg/g. The optimum pH for the free enzyme was observed at 5.0. On the other hand, immobilized invertase yielded a broad optimum pH profile between pH 5.0 and 7.0. Immobilized invertase exhibited 83% of its original activity even after two months storage at 4 °C while the free enzyme showed only 7% of its initial activity.     

Glucose biosensor based on Au nanoparticles-conductive polyaniline nanocomposite

In this paper, we report a novel glucose biosensor based on composite of Au nanoparticles (NPs)-conductive polyaniline (PANI) nanofibers. Immobilized with glucose oxidase (GOx) and Nafion on the surface of nanocomposite, a sensitive and selective biosensor for glucose was successfully developed by electrochemical oxidation of H2O2. The glucose biosensor shows a linear calibration curve over the range from 1.0x10(-6) to 8.0x10(-4) mol/L, with a slope and detection limit (S/N=3) of 2.3 mA/M and 5.0x10(-7) M, respectively. In addition, the glucose biosensor system indicates excellent reproducibility (less than 5% R.S.D.) and good operational stability (over 2 weeks).     

Preparation and characterization of polyaniline/chitosan blend film

Films consisting of a blend of a chitosan hydrogel and a conductive polymer, polyaniline (PANI), were prepared and characterized for their electrical and mechanical properties. Polyaniline in emeraldine base (EB) form was dispersed in chitosan solution and blend films were obtained by solution casting. The PANI particles in the blend films were then doped with HCl where we observed reductions in the film tensile strength and Young's modulus by about 30%, but the films electrical conductivity increased by 6 orders of magnitude. The highest electrical conductivity of the blend films was of the order 10⁻⁴ S/cm. The electrical and mechanical properties of the films varied with polyaniline content, acid dopant type, acid dopant concentration, and doping time.     

Surface functionalization of porous polypropylene membranes with polyaniline for protein immobilization

Commercial porous polypropylene membranes were chemically modified with polyaniline (PANI) using ammonium persulfate as the oxidizer. The influence of polymerization conditions on the membrane properties was studied by adsorption analysis and membrane permeability. The PANI-coated polypropylene (PANI/PP) membranes possessed high affinity toward the proteins, which can be immobilized onto the membrane surface through physical adsorption or covalent immobilization. The quantity of immobilized horseradish peroxidase (HRP) and its activity depended on the quantity and quality (oxidation level) of PANI. The storage conditions for PANI/PP membranes containing immobilized HRP were studied. HRP immobilized on the PANI/PP membrane was shown to retain 70% of its activity after 3-month storage at +5 degrees C, suggesting that this material can be used for practical application, such as in bioreactors as enzyme membranes.     

Glucose biosensor based on platinum microparticles dispersed in nano-fibrous polyaniline

A sensitive and selective amperometric glucose biosensor based on platinum microparticles dispersed in nano-fibrous polyaniline (PANI) was investigated. Poly (m-phenylenediamine) (PMPD), which was employed as an anti-interferent barrier and a protective layer to platinum microparticles, was deposited onto platinum-modified PANI in the presence of glucose oxidase. The morphology of PANI, Pt/PANI and PMPD-GOD/Pt/PANI were investigated by scanning electron microscopy. The results show that PANI has a nano-fibrous morphology. The enzyme electrode exhibits excellent response performance to glucose with linear range from 2 x 10(-6) to 12 x 10(-3) M and fast response time within 7s. Due to the selective permeability of PMPD, the enzyme electrode also shows good anti-interference to uric acid and ascorbic acid. The Michaelis-Menten constant km and the maximum current density imax of the enzyme electrode were 9.34 x 10(-3) M and 917.43 microA cm(-2), respectively. Furthermore, this glucose biosensor also has good stability and reproducibility.     

Assembly of dandelion-like Au/PANI nanocomposites and their application as SERS nanosensors

The monodisperse, uniform dandelion-like Au/polyaniline (PANI) composite nanospheres were synthesized by a simple one-step process without any additives or templates. The nanospheres are really composed of many short nanorods and the average diameter of whole nanospheres is about 180 nm. The morphology of Au/PANI composites could be controlled by adjusting the molar ratio of HAuCl(4) to aniline. The prepared nanocomposite is developed as a wonderful sensor for the detection of Hg(2+) ions, which is based upon the Raman intensity response of PANI to Hg(2+) ions. Results from the morphology-dependent sensitivity investigations show that the dandelion-like nanospheres have an ultra sensitive response (as low as 10(-11)M) compared with other morphologies. The nanosensor also exhibits good reproducibility and greater selectivity for Hg(2+) ions than the other heavy metal ions. And the mechanism was proposed. The proposed nanosensors can be applied for highly sensitive and selective chemical analysis in a variety of environmental detection.     

A sensitive nonenzymatic glucose sensor in alkaline media with a copper nanocluster/multiwall carbon nanotube-modified glassy carbon electrode

Copper (Cu) nanoclusters were electrochemically deposited on the film of a Nafion-solubilized multiwall carbon nanotube (CNTs)-modified glassy carbon electrode (CNTs-GCE), which fabricated a Cu-CNTs composite sensor (Cu-CNTs-GCE) to detect glucose with nonenzyme. Transmission electron microscopy (TEM) and X-ray diffraction (XRD) were used for the characterization of the distribution of the Cu nanoclusters on the CNTs matrix. The composite of the Cu-CNTs was investigated by the electrochemical characterization of cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS). The preliminary study shows that the nonenzymatic sensor has synergistic electrocatalytic activity to the oxidation of glucose in alkaline media. A well applicable sensor was constructed to use for the analysis of the glucose in real blood serum samples due to the large number of electrons taking part in the oxidation process, the high apparent kinetic rate constant, and the stable operation of the electrode. The linear range for the detection of the glucose is 7.0 x 10(-7) to 3.5 x 10(-3) M with a high sensitivity of 17.76 microA mM(-1), a low detection limit of 2.1 x 10(-7) M, and a fast response time of within 5s. Experiment results also showed that the sensor has good reproducibility and long-term stability and is interference free.     

Mediator-free glucose/O<Subscript>2</Subscript> biofuel cell based on a 3-dimensional glucose oxidase/SWNT/polypyrrole composite electrode

In this study, a mediator-free glucose/O₂ bio-fuel cell was developed based on a 3-dimensional carbon nanomaterial/polypyrrole composite with glucose oxidase and tyrosinase as the anodic and cathodic catalysts, respectively. This mediator-free biofuel cell has the following merits: (1) the biocatalyst was unaffected by toxic mediators and (2) current generation is independent, because there is no problem associated with mediator leakage from the electrode. The carbon nanomaterial in this 3-dimensional composite was used not only as immobilization support for the biocatalyst, but also as an electron carrier. This would be advantageous for glucose oxidation on the bioanode and O₂ reduction on the biocathode in the glucose/O₂ biofuel cell. This biofuel cell showed enhanced power density and half-life compared to other glucose/O₂ biofuel cells previously reported, producing 157.4 μW/cm³ with 1 mM glucose as fuel and 0.5 M NaCl as the electrolyte, at a cell voltage of +85 mV over 29 h with continuous 1 mM glucose feeding.     

Amperometric glucose biosensor based on single-walled carbon nanohorns

The biosensing application of single-walled carbon nanohorns (SWCNHs) was demonstrated through fabrication of an amperometric glucose biosensor. The biosensor was constructed by encapsulating glucose oxidase in the Nafion-SWCNHs composite film. The cyclic voltammograms for glucose oxidase immobilized on the composite film displayed a pair of well-defined and nearly symmetric redox peaks with a formal potential of -0.453 V. The biosensor had good electrocatalytic activity toward oxidation of glucose. To decrease detection potential, ferrocene monocarboxylic acid was used as a redox mediator. The mediated glucose biosensor shows a linear range from 0 to 6.0 mM. The biosensor shows high sensitivity (1.06 microA/mM) and stability, and can avoid the commonly coexisted interference. Because of impressive properties of SWCNHs, such as high purity and high surface area, SWCNHs and their composites are expected to be promising material for biomolecular immobilization and biosensing applications.     

High-performance bioanode based on the composite of CNTs-immobilized mediator and silk film-immobilized glucose oxidase for glucose/O2 biofuel cells

A high-performance bioanode based on the composite of carbon nanotubes (CNTs)-immobilized mediator and silk film (SF)-immobilized glucose oxidase (GOD) was developed for glucose/O(2) biofuel cell (BFC). Ferrocenecarboxaldehyde (Fc) was used as the mediator and covalently immobilized on the ethylenediamine (EDA)-functionalized CNTs (CNTs-EDA). GOD was cross-linked on the SF with glutaraldehyde (GA) as the cross-linking agent. The resulting electrode (CNTs-Fc/SF-GOD/glassy carbon (GC) electrode) exhibited good catalytic activity towards glucose oxidation and excellent stability. For the assembled glucose/O(2) BFC with the CNTs-Fc/SF-GOD/GC electrode as the bioanode and a commercial E-TEK Pt/C modified GC electrode as the cathode, the open circuit potential is 0.48 V and the maximum power density of 50.70 μW cm(-2) can be achieved at 0.15 V.     

Mechanical properties of chitosan/bamboo charcoal composite films made with normal and surface oxidized charcoal

Chitosan/bamboo charcoal composite films were prepared by blending chitosan with either virgin bamboo charcoal or bamboo charcoal modified by nitric acid oxidation to provide more hydrophilic regions on the bamboo charcoal surface. Investigation of the physical properties of these composite films revealed that the tensile strength and Young’s modulus of the chitosan films were enhanced in a dose-dependent manner by the inclusion of modified bamboo charcoal at up to 1% (w/w), whilst the elongation at break was increased by inclusion of modified bamboo charcoal at up to 0.5% (w/w). In contrast, chitosan composites with virgin bamboo charcoal at up to 0.5% or 1.0% (w/w) showed no enhancement of the tensile strength or Young’s modulus, respectively, and both parameters were reduced with higher levels of virgin bamboo charcoal. Oil, and especially water, absorption of the composite films displayed a marked and dose-dependent increase compared to those of the pure chitosan film.     

Amperometric glucose biosensor based on multilayer films via layer-by-layer self-assembly of multi-wall carbon nanotubes, gold nanoparticles and glucose oxidase on the Pt electrode

A novel amperometric glucose biosensor based on the nine layers of multilayer films composed of multi-wall carbon nanotubes (MWCNTs), gold nanoparticles (GNp) and glucose oxidase (GOD) was developed for the specific detection of glucose. MWCNTs were chemically modified with the H₂SO₄–HNO₃ pretreatment to introduce carboxyl groups which were used to interact with the amino groups of poly(allylamine) (PAA) and cysteamine via 1-ethyl-3-(3-dimethylaminopropyl) carbodiimide/N-hydroxysuccinimide cross-linking reaction, respectively. A cleaned Pt electrode was immersed in PAA, MWCNTs, cysteamine and GNp, respectively, followed by the adsorption of GOD, assembling the one layer of multilayer films on the surface of Pt electrode (GOD/GNp/MWCNTs/Pt electrode). Repeating the above process could assemble different layers of multilayer films on the Pt electrode. PBS washing was applied at the end of each assembly deposition for dissociating the weak adsorption. Film assembling and characterization were studied by transmission electron microscopy and quartz crystal microbalance, and properties of the resulting glucose biosensors were measured by electrochemical measurements. The marked electrocatalytic activity of Pt electrode based on multilayer films toward H₂O₂ produced during GOD enzymatic reactions with glucose permitted effective low-potential amperometric measurement of glucose. Taking the sensitivity and selectivity into consideration, the applied potential of 0.35 V versus Ag/AgCl was chosen for the oxidation detection of H₂O₂ in this work. Among the resulting glucose biosensors, the biosensor based on nine layers of multilayer films was best. It showed a wide linear range of 0.1–10 mM glucose, with a remarkable sensitivity of 2.527 μA/mM, a detection limit of 6.7 μM estimated at a signal-to-noise ratio of 3 and fast response time (within 7 s). Moreover, it exhibited good reproducibility, long-term stability and the negligible interferences of ascorbic acid, uric acid and acetaminophen. The study can provide a feasible approach on developing new kinds of oxidase-based amperometric biosensors, and can be used as an illustration for constructing various hybrid structures.     

Amperometric biosensor for choline based on layer-by-layer assembled functionalized carbon nanotube and polyaniline multilayer film

Conducting polymer film was prepared by electrochemical polymerization of aniline. Multiwalled carbon nanotubes (MWNTs) were treated with a mixture of concentrated sulfuric and nitric acid to introduce carboxylic acid groups to the nanotubes. By using the layer-by-layer method, homogeneous and stable MWNTs and polyaniline (PANI) multilayer films were alternately assembled on glassy carbon (GC) electrodes. Conducting polymer of PANI had three main functions: (i) excellent antiinterference ability, (ii) protection ability in favor of increasing the amount of the MWNTs immobilized on GC electrodes, and (iii) superior transducing ability. The protection effect of PANI film and the electrostatic interaction between positively charged PANI and negatively charged MWNTs both attributed to immobilizing abundant MWNTs stably, thereby enhancing the catalytic activity. The layer-by-layer assembled MWNTs and PANI-modified GC electrodes offered a significant decrease in the overvoltage for the H2O2 and were shown to be excellent amperometric sensors for H2O2 from +0.2V over a wide range of concentrations. As an application example, by linking choline oxidase (CHOD), an amplified biosensor toward choline was prepared. The choline biosensor exhibited a linear response range of 1x10(-6) to 2x10(-3) M with a correlation coefficient of 0.997, and the response time and detection limit (S/N=3) were determined to be 3 s and 0.3 microM, respectively. The antiinterference biosensor displays a rapid response and an expanded linear response range as well as excellent reproducibility and stability.     

A metal dispersed sol-gel biocomposite amperometric glucose biosensor

A new glucose biosensor has been fabricated by immobilizing glucose oxidase into a copper dispersed sol-gel derived ceramic-graphite composite. The copper in the biocomposite offers excellent electrocatalytic activity towards the reduction (at -0.2 V) as well as oxidation (at +0.45 V) of hydrogen peroxide liberated in the enzymatic reaction enabling sensitive and selective determination of glucose. A linear response to glucose in the concentration range between 2.7 x 10(-5) to 4.0 x 10(-3) M with a correlation coefficient of 0.9987 and 4.0 x 10(-5) to 5.6 x 10(-3) M with a correlation coefficient of 0.9989 were observed with the electrocatalytic reduction and oxidation, respectively. Ascorbic acid and uric acid did not interfere with the glucose measurement during catalytic reduction at -0.2 V, a Nafion membrane was used to eliminate these interferences during the electrocatalytic oxidation at +0.45 V. The combination of copper catalysis and the promising feature of sol-gel biocomposite favor the sensitive and selective determination of glucose with improved analytical capabilities.     

Controllable anchoring of gold nanoparticles to polypyrrole nanofibers by hydrogen bonding and their application in nonenzymatic glucose sensors

An enzymeless glucose biosensor based on polypyrrole nanofibers-supporting Au nanoparticles (Au/PPyNFs) was investigated in this study. The Au/PPyNFs heterogeneous composite materials were synthesized in-situ via hydrogen bonding interactions for the assembly of polyethyleneimine (PEI) on the surface of polypyrrole nanofibers (PPyNFs). By changing the molar ratio of PPy to HAuCl(4), Au/PPyNFs with different Au loadings were obtained. The morphology and composition of Au/PPyNFs were characterized using SEM, TEM, FTIR, XRD and XPS, respectively. The hybrids exhibited a high electrocatalytic activity toward glucose oxidation, which is prerequisite for the catalysts to be applied in amperometric glucose sensors. By using the nonenzymatic glucose sensor based on Au/PPyNFs, 0.2-13mM glucose can be detected with a sensitivity of 1.003μAcm(-2)mM(-1) and a good linearity (R(2)=0.9993) between current density and glucose concentration. The proposed glucose sensor provides a promising strategy to construct fast, sensitive, and anti-interfering amperometric sensors for early diagnosis and prevention of diabetes.     

An amperometric biosensor based on laccase immobilized onto Fe(3)O(4)NPs/cMWCNT/PANI/Au electrode for determination of phenolic content in tea leaves extract

A method is described for the construction of an amperometric biosensor for detection of phenolic compounds based on covalent immobilization of laccase onto iron oxide nanoparticles (Fe(3)O(4)NPs) decorated carboxylated multiwalled carbon nanotubes (cMWCNTs)/polyaniline (PANI) composite electrodeposited onto a gold (Au) electrode. The modified electrode was characterized by scanning electron microscopy (SEM), Fourier transform infrared (FTIR) spectroscopy, cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS). The biosensor showed optimum response within 3s at pH 6.0 (0.1M sodium acetate buffer) and 35°C, when operated at 0.3V vs. Ag/AgCl. Linear range, detection limit were 0.1-10μM (lower concentration range) and 10-500μM (higher concentration range), and 0.03μM respectively. The sensor measured total phenolic content in tea leaves extract. The enzyme electrode lost 25% of its initial activity after its 150 uses over a period of 4 months, when stored at 4°C.     

Carbon nanotube/gold nanoparticles/polyethylenimine-functionalized ionic liquid thin film composites for glucose biosensing

A novel glucose biosensor based on immobilization of glucose oxidase (GOD) in thin films of polyethylenimine-functionalized ionic liquid (PFIL), containing a mixture of carbon nanotubes (CNT) and gold nanoparticles (AuNPs) and deposited on glassy carbon electrodes, was developed. Direct electrochemistry of glucose oxidase in the film was observed, with linear glucose response up to 12mM. The PFIL-stabilized gold nanoparticles had a diameter of 2.4+/-0.8nm and exhibited favorable stability (stored even over one month with invisible change in UV-vis spectroscopic measurements). In addition, CNT were also well dispersed in the PFIL matrix, then, the resulting CNT/AuNPs/PFIL composites film showed high electrocatalytic activity toward reduction of hydrogen peroxide and oxygen. Here, PFIL, due to its high ionic conductivity, good solubility to CNT, and stability to nanoparticles, played an important role in constructing stable CNT/AuNPs/PFIL/GOD composites. And good biocompatibility of PFIL also offered a friendly environment for the immobilization of biomolecules.     

A super highly sensitive glucose biosensor based on Au nanoparticles-AgCl@polyaniline hybrid material

Gold nanoparticles (AuNPs) with an average diameter of 5nm were assembled on the surface of silver chloride@polyaniline (PANI) core-shell nanocomposites (AgCl@PANI). Attenuated total reflection Fourier transform infrared spectroscopy (ATR-FTIR) suggested that AuNPs were incorporated on AgCl@PANI through coordination bonds instead of electrostatic interaction. The resulting AuNPs-AgCl@PANI hybrid material exhibited good electroactivity at a neutral pH environment. An amperometric glucose biosensor was developed by adsorption of glucose oxidase (GOx) on an AuNPs-AgCl@PANI modified glassy carbon (GC) electrode. AuNPs-AgCl@PANI could provide a biocompatible surface for high enzyme loading. Due to size effect, the AuNPs in the hybrid material could act as a good catalyst for both oxidation and reduction of H(2)O(2). As the measurement of glucose was based on the electrochemical detection of H(2)O(2) generated by enzyme-catalyzed-oxidation of glucose, the biosensor exhibited a super highly sensitive response to the analyte with a detection limit of 4 pM. Moreover, the biosensor showed good reproducibility and operation stability. The effects of some factors, such as temperature and pH value, were also studied.     

Glucose biosensor prepared by glucose oxidase encapsulated sol-gel and carbon-nanotube-modified basal plane pyrolytic graphite electrode

A new glucose biosensor has been fabricated by immobilizing glucose oxidase into a sol-gel composite at the surface of a basal plane pyrolytic graphite (bppg) electrode modified with multiwall carbon nanotube. First, the bppg electrode is subjected to abrasive immobilization of carbon nanotubes by gently rubbing the electrode surface on a filter paper supporting the carbon nanotubes. Second, the electrode surface is covered with a thin film of a sol-gel composite containing encapsulated glucose oxidase. The carbon nanotubes offer excellent electrocatalytic activity toward reduction and oxidation of hydrogen peroxide liberated in the enzymatic reaction between glucose oxidase and glucose, enabling sensitive determination of glucose. The amperometric detection of glucose is carried out at 0.3 V (vs saturated calomel electrode) in 0.05 M phosphate buffer solution (pH 7.4) with linear response range of 0.2-20 mM glucose, sensitivity of 196 nA/mM, and detection limit of 50 microM (S/N=3). The response time of the electrode is < 5s when it is stored dried at 4 degrees C, the sensor showed almost no change in the analytical performance after operation for 3 weeks. The present carbon nanotube sol-gel biocomposite glucose oxidase sensor showed excellent properties for the sensitive determination of glucose with good reproducibility, remarkable stability, and rapid response and in comparison to bulk modified composite biosensors the amounts of enzyme and carbon nanotube needed for electrode fabrication are dramatically decreased.