Comparison of plate count agar and R2A medium for enumeration of heterotrophic bacteria in natural mineral water

In order to recover as many viable bacteria as possible from natural mineral water, in this study we have compared the counts obtained with the standard method (pour plate procedure with Plate Count Agar (PCA)) and counts with alternative test methods (PCA/spread plates, R2A medium/pour plates and R2A medium/spread plates). The results showed that counts with R2A medium/spread plates at 22°C and after a 7-day incubation period were more than 343% higher than those obtained with PCA/pour plate method. At 37°C and after a 3-day incubation period, the R2A pour plate technique gave counts about 368% greater than for the standard method. Moreover, while Pseudomonas, Comamonas and Acinetobacter species were isolated both from PCA and R2A medium, Flavobacterium spp. and Arthrobacter spp. were isolated only from R2A medium. For its higher productivity, R2A medium should be recommended for heterotrophic plate counts in natural mineral water.     

A new medium for the enumeration and subculture of bacteria from potable water.

Plate count agar is presently the recommended medium for the standard bacterial plate count (35 degrees C, 48-h incubation) of water and wastewater. However, plate count agar does not permit the growth of many bacteria that may be present in treated potable water supplies. A new medium was developed for use in heterotrophic plate count analyses and for subculture of bacteria isolated from potable water samples. The new medium, designated R2A, contains 0.5 g of yeast extract, 0.5 g of Difco Proteose Peptone no. 3 (Difco Laboratories), 0.5 g of Casamino Acids (Difco), 0.5 g of glucose, 0.5 g of soluble starch, 0.3 g of K2HPO4, 0.05 g of MgSO4 X 7H2O, 0.3 g of sodium pyruvate, and 15 g of agar per liter of laboratory quality water. Adjust the pH to 7.2 with crystalline K2HPO4 or KH2PO4 and sterilize at 121 degrees C for 15 min. Results from parallel studies with spread, membrane filter, and pour plate procedures showed that R2A medium yielded significantly higher bacterial counts than did plate count agar. Studies of the effect of incubation temperature showed that the magnitude of the count was inversely proportional to the incubation temperature. Longer incubation time, up to 14 days, yielded higher counts and increased detection of pigmented bacteria. Maximal bacterial counts were obtained after incubation at 20 degrees C for 14 days. As a tool to monitor heterotrophic bacterial populations in water treatment processes and in treated distribution water, R2A spread or membrane filter plates incubated at 28 degrees C for 5 to 7 days is recommended.(ABSTRACT TRUNCATED AT 250 WORDS)     

A new medium for the enumeration and subculture of bacteria from potable water

Plate count agar is presently the recommended medium for the standard bacterial plate count (35 degrees C, 48-h incubation) of water and wastewater. However, plate count agar does not permit the growth of many bacteria that may be present in treated potable water supplies. A new medium was developed for use in heterotrophic plate count analyses and for subculture of bacteria isolated from potable water samples. The new medium, designated R2A, contains 0.5 g of yeast extract, 0.5 g of Difco Proteose Peptone no. 3 (Difco Laboratories), 0.5 g of Casamino Acids (Difco), 0.5 g of glucose, 0.5 g of soluble starch, 0.3 g of K2HPO4, 0.05 g of MgSO4 X 7H2O, 0.3 g of sodium pyruvate, and 15 g of agar per liter of laboratory quality water. Adjust the pH to 7.2 with crystalline K2HPO4 or KH2PO4 and sterilize at 121 degrees C for 15 min. Results from parallel studies with spread, membrane filter, and pour plate procedures showed that R2A medium yielded significantly higher bacterial counts than did plate count agar. Studies of the effect of incubation temperature showed that the magnitude of the count was inversely proportional to the incubation temperature. Longer incubation time, up to 14 days, yielded higher counts and increased detection of pigmented bacteria. Maximal bacterial counts were obtained after incubation at 20 degrees C for 14 days. As a tool to monitor heterotrophic bacterial populations in water treatment processes and in treated distribution water, R2A spread or membrane filter plates incubated at 28 degrees C for 5 to 7 days is recommended.(ABSTRACT TRUNCATED AT 250 WORDS)     

Heterotrophic plate counts of surface water samples by using impedance methods.

Membrane filtration, spread plating, and pour plating are conventional methods used to determine the heterotrophic plate counts of water samples. Impedance methods were investigated as an alternative to conventional methods, since sample dilution is not required and the bacterial count can be estimated within 24 h. Comparisons of impedance signals obtained with different water samples revealed that capacitance produced faster detection times than conductance. Moreover, the correlation between heterotrophic plate count and detection time was highest (r = 0.966) when capacitance was used. Linear and quadratic regressions of heterotrophic plate count and impedance detection time were affected by incubation temperatures. Regressions between heterotrophic plate counts based on conventional methods and detection times of water samples incubated at less than or equal to 25 degrees C had R2 values of 0.878 to 0.933. However, regressions using detection times of water samples incubated at greater than or equal to 30 degrees C had lower R2 values, even though water samples produced faster detection times. Comparisons between broth-based versions of R2A medium and plate count agar revealed that the latter correlated highly with heterotrophic plate count, provided that water samples were incubated at 25 degrees C and impedance measurements were conducted with the capacitance signal (r = 0.966). When the linear regression of this relationship was tested with 100 water samples, the correlation between predicted and actual log10 CFU milliliter-1 was 0.869. These results indicate that impedance methods provide a suitable alternative to conventional methods.     

Heterotrophic plate counts of surface water samples by using impedance methods.

Membrane filtration, spread plating, and pour plating are conventional methods used to determine the heterotrophic plate counts of water samples. Impedance methods were investigated as an alternative to conventional methods, since sample dilution is not required and the bacterial count can be estimated within 24 h. Comparisons of impedance signals obtained with different water samples revealed that capacitance produced faster detection times than conductance. Moreover, the correlation between heterotrophic plate count and detection time was highest (r = 0.966) when capacitance was used. Linear and quadratic regressions of heterotrophic plate count and impedance detection time were affected by incubation temperatures. Regressions between heterotrophic plate counts based on conventional methods and detection times of water samples incubated at less than or equal to 25 degrees C had R2 values of 0.878 to 0.933. However, regressions using detection times of water samples incubated at greater than or equal to 30 degrees C had lower R2 values, even though water samples produced faster detection times. Comparisons between broth-based versions of R2A medium and plate count agar revealed that the latter correlated highly with heterotrophic plate count, provided that water samples were incubated at 25 degrees C and impedance measurements were conducted with the capacitance signal (r = 0.966). When the linear regression of this relationship was tested with 100 water samples, the correlation between predicted and actual log10 CFU milliliter-1 was 0.869. These results indicate that impedance methods provide a suitable alternative to conventional methods.     

Statistical approach for comparison between methods of bacterial enumeration in drinking water

A general statistical procedure based on the likelihood ratio test is presented for the purpose of comparing estimates of mean bacterial density derived from different sets of data. This approach is much more appropriate than the conventional ways of analyzing bacteriological results (e.g., analysis of variance) which usually require previous transformation of the data. An illustrative application of the method compares three distinct titration techniques for enumerating heterotrophic bacteria in drinking water at 20°C incubation temperature. It was shown that both the standard plate count (SPC) and the membrane filter (MF) procedures supplied substantially the same information, whereas the microplate technique using the most probable number (MPN) for total bacterial enumeration could yield considerably different estimates: MPN values were significantly lower in three cases and significantly higher in one case out of a total of five experiments. The results consistently indicate a strong interaction between the technique used and the sample analyzed. Three different media (nutrient agar, R-2A low nutrient agar and m-SPC agar) were then evaluated for enumerating heterotrophic bacteria, using the MF technique at 48, 72 and 96 h of incubation time at 20°C. Although the media recovered approximately the same numbers of bacteria after 96 h of incubation, statistically significant discrepancies occurred after intermediate periods of incubation, perhaps because the relative rates of bacterial growth differed among media.     

A membrane filter procedure for assaying cytotoxic activity in heterotrophic bacteria isolated from drinking water

Cytotoxic activity assays of Gram-negative, heterotrophic bacteria are often laborious and time consuming. The objective of this study was to develop in situ procedures for testing potential cytotoxic activities of heterotrophic bacteria isolated from drinking water systems. Water samples were passed through 0·45 μm membrane filters which were then placed upon appropriate media and incubated. After incubation, each membrane filter was transferred to the surface of Y-1 mouse adrenal cells overlaid with 1% agar. The filters were removed after exposure for 15 min. The Y-1 cells were then incubated at 37°C in 2·5% CO₂ for an additional 24 h. The release of putative cytotoxic and cytotonic products from the bacterial colonies was recognized by zones of cellular lysis and injury of Y-1 cells that appeared immediately beneath the membrane. Cytotoxic strains of Aeromonas, Vibrio, Escherichia , and Legionella spp. were readily recognized by this method. About 1% of the bacteria isolated from drinking water also released cytotoxic products. This frequency was dependent upon the primary medium used and the density of bacteria present. The majority of cytotoxic strains isolated from drinking water also expressed protease activity (95%) and haemolytic activity (70%). This in situ membrane filter procedure is a facile method for simultaneously testing many different bacterial colonies.     

Phylogenetic assessment of heterotrophic bacteria from a water distribution system using 16S rDNA sequencing

Determination of a heterotrophic plate count (HPC) for drinking-water samples alone is not enough to assess possible health hazards associated with sudden changes in the bacterial count. Speciation is very crucial to determine whether the population includes pathogens and (or) opportunistic pathogens. Most of the isolates recovered from drinking water samples could not be allocated to a specific phylogenetic branch based on the use of conventional diagnostic methods. The present study had to use phylogenetic analysis, which was simplified by determining and using the first 500-bp sequence of the 16S rDNA, to successfully identify the type and species of bacteria found in the samples. Gram-positive bacteria alpha-, beta-, and gamma-Proteobacteria were found to be the major groups representing the heterotrophic bacteria in drinking water. The study also revealed that the presence of sphingomonads in drinking water supplies may be much more common than has been reported so far and thus further studies are merited. The intermittent mode of supply, mainly characterized by water stagnation and flow interruption associated possibly with biofilm detachment, raised the possibility that the studied bacterial populations in such systems represented organisms coming from 2 different niches, the biofilm and the water column.     

Nonphotosynthetic pigmented bacteria in a potable water treatment and distribution system

The occurrence of pigmented bacteria in potable water, from raw source water through treatment to distribution water, including dead-end locations, was compared at sample sites in a large municipal water system. Media used to enumerate heterotrophic bacteria and differentiate pigmented colonies were standard method plate count (SPC), m-SPC, and R2A agars, incubated up to 7 days at 35 degrees C. The predominant pigmented bacteria at most sample locations were yellow and orange, with a small incidence of pink organisms at the flowing distribution site. Seasonal variations were seen, with the yellow and orange organisms shifting in dominance. SPC agar was the least productive medium for both heterotroph counts and pigmented bacteria differentiation. At the flowing distribution site, percentages of pigmented bacteria on SPC medium ranged from 2.3 to 9.67 times less than on m-SPC and from 2.3 to 9.86 times less than on R2A. At the same site, seasonal trends in the percentage of pigmented bacteria were the same for m-SPC and R2A media, and the highest and lowest percentages occurred in the fall and winter, respectively. At site 6, there appeared to be an inverse relationship between the yellow and orange pigmented groups, but upon analysis, this did not hold and all correlations between yellow and orange pigmented bacteria were positive. The study results indicate that pigmented bacteria could readily be detected by using plate counting media developed for heterotroph enumeration in potable waters with incubation periods of 7 days. Pigmented bacteria can be used as an additional marker for monitoring changes in water quality. High numbers of heterotrophs, including pigmented forms, were found at dead-end locations, usually in the absence of a free chlorine residual and when the water temperature was greater than 16 degrees C. The association of some pigmented bacteria with nosocomial and other infections raises concern that the organisms may have originated from the potable water supply. High levels of pigmented bacteria could pose an increased health risk to immunologically compromised individuals. Therefore, the bacterial quality of the distribution water should be controlled to prevent the development of high concentrations of heterotrophic plate count bacteria, including the pigmented forms.     

Nonphotosynthetic pigmented bacteria in a potable water treatment and distribution system.

The occurrence of pigmented bacteria in potable water, from raw source water through treatment to distribution water, including dead-end locations, was compared at sample sites in a large municipal water system. Media used to enumerate heterotrophic bacteria and differentiate pigmented colonies were standard method plate count (SPC), m-SPC, and R2A agars, incubated up to 7 days at 35 degrees C. The predominant pigmented bacteria at most sample locations were yellow and orange, with a small incidence of pink organisms at the flowing distribution site. Seasonal variations were seen, with the yellow and orange organisms shifting in dominance. SPC agar was the least productive medium for both heterotroph counts and pigmented bacteria differentiation. At the flowing distribution site, percentages of pigmented bacteria on SPC medium ranged from 2.3 to 9.67 times less than on m-SPC and from 2.3 to 9.86 times less than on R2A. At the same site, seasonal trends in the percentage of pigmented bacteria were the same for m-SPC and R2A media, and the highest and lowest percentages occurred in the fall and winter, respectively. At site 6, there appeared to be an inverse relationship between the yellow and orange pigmented groups, but upon analysis, this did not hold and all correlations between yellow and orange pigmented bacteria were positive. The study results indicate that pigmented bacteria could readily be detected by using plate counting media developed for heterotroph enumeration in potable waters with incubation periods of 7 days. Pigmented bacteria can be used as an additional marker for monitoring changes in water quality. High numbers of heterotrophs, including pigmented forms, were found at dead-end locations, usually in the absence of a free chlorine residual and when the water temperature was greater than 16 degrees C. The association of some pigmented bacteria with nosocomial and other infections raises concern that the organisms may have originated from the potable water supply. High levels of pigmented bacteria could pose an increased health risk to immunologically compromised individuals. Therefore, the bacterial quality of the distribution water should be controlled to prevent the development of high concentrations of heterotrophic plate count bacteria, including the pigmented forms.     

Bacterial colonization of domestic reverse-osmosis water filtration units

We have analyzed the bacterial content of water from the reservoirs of 300 reverse-osmosis units installed in households. The heterotrophic plate counts on R2A medium (20 and 35 degrees C) ranged from 0 to 10(7) colony forming units per millilitre (cfu/mL). Most reservoirs contained water with bacterial counts between 10(4) and 10(5) cfu/mL. The bacteria identified were Pseudomonas (not aeruginosa), Alcaligenes or Moraxella, Acinetobacter, Flavobacterium, and Chromobacterium. This report emphasizes the importance of bacterial colonization by heterotrophic bacteria in water reservoirs from domestic reverse-osmosis units.     

A membrane filter procedure for assaying cytotoxic activity in heterotrophic bacteria isolated from drinking water

Cytotoxic activity assays of Gram-negative, heterotrophic bacteria are often laborious and time consuming. The objective of this study was to develop in situ procedures for testing potential cytotoxic activities of heterotrophic bacteria isolated from drinking water systems. Water samples were passed through 0.45 microns membrane filters which were then placed upon appropriate media incubated. After incubation, each membrane filter was transferred to the surface of Y-1 mouse adrenal cells overlaid with 1% agar. The filters were removed after exposure for 15 min. The Y-1 cells were then incubated at 37 degrees C in 2.5% CO2 for an additional 24 h. The release of putative cytotoxic and cytotonic products from the bacterial colonies was recognized by zones of cellular lysis and injury of Y-1 cells that appeared immediately beneath the membrane. Cytotoxic strains of Aeromonas, Vibrio, Escherichia, and Legionella spp. were readily recognized by this method. About 1% of the bacteria isolated from drinking water also released cytotoxic products. This frequency was dependent upon the primary medium used and the density of bacteria present. The majority of cytotoxic strains isolated from drinking water also expressed protease activity (95%) and haemolytic activity (70%). This in situ membrane filter procedure is a facile method for simultaneously testing many different bacterial colonies.     

Biofilm formation in drinking water affected by low concentrations of phosphorus

Abstract: There are geographical regions where microbial growth in drinking waters is limited by phosphorus instead of organic carbon. In these drinking waters even a low amount of phosphorus can strongly enhance microbial growth. The formation of biofilm can be limited by low availability of phosphorus in drinking waters with low content of phosphorus. The formation of biofilms on polyvinyl chloride plates was studied in laboratory experiments with water containing 48 microg/L assimilable organic carbon and 0.19 microg/L microbially available phosphorus. We found that low additions of phosphate (1-5 microg/L PO4(3-)-P) to water increased microbial growth in the water and in the biofilm. The effect of phosphorus on microbial growth could be detected by determining either the microbial cell production or the content of ATP in biofilms. Also, in steady-state biofilms, microbial concentrations were higher with phosphorus addition as enumerated by heterotrophic plate counts on R2A-agar and acridine orange direct counting. This work confirms the earlier findings of the importance of phosphorus for microbial growth in humic-rich drinking waters.     

Alterations in the major heterotrophic bacterial populations isolated from a still bottled mineral water

The heterotrophic bacterial population of a bottled mineral water stored in returnable glass bottles and in polyvinyl chloride (PVC) bottles at room temperature was studied over 9-12 months. The plate counts in R2A medium incubated at 22 degrees and 37 degrees C were low initially, increasing to 10(4)-10(5) cfu/ml within a few days of bottling. The number of bacteria recovered at 22 degrees C from PVC bottles was fairly constant during the storage period, but the population isolated at 37 degrees C decreased markedly after storage for 1 year. The major components of the population were Pseudomonas strains, one of which was identified as Pseudomonas vesicularis. Major changes took place during storage; two groups of bacteria (B and C) were dominant initially, but during the latter period of storage other groups (F, G and H) increased in number.     

饮用水微生物的安全快速检测

【目的】为了更好地分析饮用水中的微生物含量。【方法】利用流式细胞术(Flowcytometry,FCM)、ATP测定方法检测瓶装无气饮用水中的微生物数量、可同化有机碳(Assimilable organic carbon,AOC)含量以及微生物活性,并将检测结果与传统的饮用水微生物检测技术相对照。【结果】FCM方法可快速区分水样中的活性细菌和非活性细菌,AOC含量反映了水样中微生物再生能力;而ATP检测方法也能比异养细菌平板计数法(Heterotrophic plate count,HPC)更好地反映瓶装无气饮用水中的实际微生物含量。【结论】FCM、ATP测定方法要明显优于依赖于培养的传统方法。     

Fluorometric determination of the DNA concentration in municipal drinking water

DNA concentrations in municipal drinking water samples were measured by fluorometry, using Hoechst 33258 fluorochrome. The concentration, extraction, and detection methods used were adapted from existing techniques. The method is reproducible, fast, accurate, and simple. The amounts of DNA per cell for five different bacterial isolates obtained from drinking water samples were determined by measuring DNA concentration and total cell concentration (acridine orange epifluorescence direct cell counting) in stationary pure cultures. The relationship between DNA concentration and epifluorescence total direct cell concentration in 11 different drinking water samples was linear and positive; the amounts of DNA per cell in these samples did not differ significantly from the amounts in pure culture isolates. We found significant linear correlations between DNA concentration and colony-forming unit concentration, as well as between epifluorescence direct cell counts and colony-forming unit concentration. DNA concentration measurements of municipal drinking water samples appear to monitor changes in bacteriological quality at least as well as total heterotrophic plate counting and epifluorescence direct cell counting.     

Fluorometric determination of the DNA concentration in municipal drinking water.

DNA concentrations in municipal drinking water samples were measured by fluorometry, using Hoechst 33258 fluorochrome. The concentration, extraction, and detection methods used were adapted from existing techniques. The method is reproducible, fast, accurate, and simple. The amounts of DNA per cell for five different bacterial isolates obtained from drinking water samples were determined by measuring DNA concentration and total cell concentration (acridine orange epifluorescence direct cell counting) in stationary pure cultures. The relationship between DNA concentration and epifluorescence total direct cell concentration in 11 different drinking water samples was linear and positive; the amounts of DNA per cell in these samples did not differ significantly from the amounts in pure culture isolates. We found significant linear correlations between DNA concentration and colony-forming unit concentration, as well as between epifluorescence direct cell counts and colony-forming unit concentration. DNA concentration measurements of municipal drinking water samples appear to monitor changes in bacteriological quality at least as well as total heterotrophic plate counting and epifluorescence direct cell counting.     

Improved methods for the enumeration of heterotrophic bacteria in bottled mineral waters

At this time the European Union regulations require that the heterotrophic plate counts (HPC) of mineral waters be assessed at two recovery temperatures: 22 degrees C for 72 h and 37 degrees C for 24 h. This procedure is time consuming and expensive. Development of new rapid methods for microbiological assessment of the microbial flora in the bottled water is an industry-driven need.The objectives of this work were to develop a method for the HPC that utilises only one recovery temperature and one incubation period and evaluate the use of, the LIVE/DEAD(R) BacLight Bacterial Viability Kit, 5-cyano-2,3-ditotyl tetrazolium chloride (CTC) and impedance methods to enumerate viable bacteria in bottled mineral water.Results showed that incubation at 30 degrees C could be used instead of incubation at 22 degrees C and 37 degrees C. Good correlation exists between counts at 30 degrees C and counts at 22 degrees C (r>0.90) and all the pathogens important in mineral water analyses grow similarly at 30 degrees C and 37 degrees C during 24 h.It was demonstrated that impedance methods might be useful to the mineral water industry as a rapid indicator of microbiological quality of the water.Results obtained with BacLight and CTC were similar to those obtained with plate counts.     

How to optimize the drop plate method for enumerating bacteria

The drop plate (DP) method can be used to determine the number of viable suspended bacteria in a known beaker volume. The drop plate method has some advantages over the spread plate (SP) method. Less time and effort are required to dispense the drops onto an agar plate than to spread an equivalent total sample volume into the agar. By distributing the sample in drops, colony counting can be done faster and perhaps more accurately. Even though it has been present in the laboratory for many years, the drop plate method has not been standardized. Some technicians use 10-fold dilutions, others use twofold. Some technicians plate a total volume of 0.1 ml, others plate 0.2 ml. The optimal combination of such factors would be useful to know when performing the drop plate method.This investigation was conducted to determine (i) the standard deviation of the bacterial density estimate, (ii) the cost of performing the drop plate procedure, (iii) the optimal drop plate design, and (iv) the advantages of the drop plate method in comparison to the standard spread plate method. The optimal design is the combination of factor settings that achieves the smallest standard deviation for a fixed cost. Computer simulation techniques and regression analysis were used to express the standard deviation as a function of the beaker volume, dilution factor, and volume plated. The standard deviation expression is also applicable to the spread plate method.     

Bacteria associated with granular activated carbon particles in drinking water

A sampling protocol was developed to examine particles released from granular activated carbon filter beds. A gauze filter/Swinnex procedure was used to collect carbon fines from 201 granular activated carbon-treated drinking water samples over 12 months. Application of a homogenization procedure (developed previously) indicated that 41.4% of the water samples had heterotrophic plate count bacteria attached to carbon particles. With the enumeration procedures described, heterotrophic plate count bacteria were recovered at an average rate of 8.6 times higher than by conventional analyses. Over 17% of the samples contained carbon particles colonized with coliform bacteria as enumerated with modified most-probable-number and membrane filter techniques. In some instances coliform recoveries were 122 to 1,194 times higher than by standard procedures. Nearly 28% of the coliforms attached to these particles in drinking water exhibited the fecal biotype. Scanning electron micrographs of carbon fines from treated drinking water showed microcolonies of bacteria on particle surfaces. These data indicate that bacteria attached to carbon fines may be an important mechanism by which microorganisms penetrate treatment barriers and enter potable water supplies.