Production of 1,3-propanediol by Klebsiella pneumoniae from glycerol broth

Broth containing 152 g glycerol l⁻¹ from Candida krusei culture was converted to 1,3-propanediol by Klebsiella pneumoniae. Residual glucose in the broth promoted growth of K. pneumoniae while acetate was inhibitory. After desalination treatment of glycerol broth by electrodialysis, the acetate in the broth was removed. A fed-batch culture with electrodialytically pretreated broth as␣substrate was developed giving 53 g 1,3- propanediol l⁻¹ with a yield of 0.41 g g⁻¹ glycerol and a productivity of 0.94 g l⁻¹ h⁻¹.     

Microbial production of 1,3-propanediol by Klebsiella pneumoniae using crude glycerol from biodiesel preparations

1,3-Propanediol (1,3-PD) was produced by Klebsiella pneumoniae using crude glycerol obtained from biodiesel production. The 1,3-PD concentration of 51.3 g/l⁻¹ on crude glycerol from alkali-catalyzed methanolysis of soybean oil was comparable to that of 53 g/l⁻¹ on crude glycerol derived from a lipase-catalyzed process. The productivities of 1.7 g l⁻¹ h⁻¹ on crude glycerol were comparable to that of 2 g l⁻¹ h⁻¹ on pure glycerol. It could be concluded that the crude glycerol could be directly converted to 1,3-PD without any prior purification.     

一株产1，3-丙二醇的克雷伯氏菌的噬菌体生物学特性

[目的]克雷伯氏菌发酵生产1,3-丙二醇过程中发生噬菌体感染会严重影响宿主菌的生长和目标产物的生成,因此分离克雷伯氏菌噬菌体并考察其生物学特性对预防和控制噬菌体感染具有重要意义.[方法]采用敏感指示菌法及Adams双层平板法从感染噬菌体的肺炎克雷伯氏杆菌发酵液中分离得到一株噬菌体;纯化后用磷钨酸负染法电镜观察;手工法提取噬菌体核酸,酶切后琼脂糖凝胶电泳分析;同时考察了其最佳感染复数、一步生长曲线及对温度、pH、紫外线、乙醚和氯仿等理化因素的敏感性等生理特性;最后考察了噬菌体对肺炎克雷伯氏杆菌生长和发酵的影响.[结果]分离出一株肺炎克雷伯氏杆菌溶源性噬菌体,其噬菌斑为无晕环透明圆斑,直径约1.5 mm;其头部为直径约60 nm-70 nm的球体,有一长约160 nm的丝状长尾;基因组核酸能被双链DNA内切酶EcoR Ⅰ及HindⅢ切开,大小约42 kb;对高温和紫外线敏感,耐碱性而受强酸抑制,对氯仿不敏感;最佳感染复数为1,潜伏期与裂解期均为50 min,裂解量为343个;感染噬菌体的肺炎克雷伯氏杆菌的细胞生长延滞约8h,代谢流偏向乳酸途径.[结论]该噬菌体属于无包膜长尾噬菌体,能改变克雷伯氏菌发酵生产1,3-丙二醇的代谢规律,为1,3-丙二醇发酵生产过程中噬菌体感染的预防和控制研究奠定了基础.     

Potential and limitations of Klebsiella pneumoniae as a microbial cell factory utilizing glycerol as the carbon source

Klebsiella pneumoniae is a Gram-negative facultative anaerobe that metabolizes glycerol efficiently under both aerobic and anaerobic conditions. This microbe is considered an outstanding biocatalyst for transforming glycerol into a variety of value-added products. Crude glycerol is a cheap carbon source and can be converted by K. pneumoniae into useful compounds such as lactic acid, 3-hydroxypropionic acid, ethanol, 1,3-propanediol, 2,3-butanediol, and succinic acid. This review summarizes glycerol metabolism in K. pneumoniae and its potential as a microbial cell factory for the production of commercially important acids and alcohols. Although many challenges remain, K. pneumoniae is a promising workhorse when glycerol is used as the carbon source.     

Systems metabolic engineering of Corynebacterium glutamicum for high-level production of 1,3-propanediol from glucose and xylose

Corynebacterium glutamicum is a versatile chassis which has been widely used to produce various amino acids and organic acids. In this study, we report the development of an efficient C. glutamicum strain to produce 1,3-propanediol (1,3-PDO) from glucose and xylose by systems metabolic engineering approaches, including (1) construction and optimization of two different glycerol synthesis modules; (2) combining glycerol and 1,3-PDO synthesis modules; (3) reducing 3-hydroxypropionate accumulation by clarifying a mechanism involving 1,3-PDO re-consumption; (4) reducing the accumulation of toxic 3-hydroxypropionaldehyde by pathway engineering; (5) engineering NADPH generation pathway and anaplerotic pathway. The final engineered strain can efficiently produce 1,3-PDO from glucose with a titer of 110.4 g/L, a yield of 0.42 g/g glucose, and a productivity of 2.30 g/L/h in fed-batch fermentation. By further introducing an optimized xylose metabolism module, the engineered strain can simultaneously utilize glucose and xylose to produce 1,3-PDO with a titer of 98.2 g/L and a yield of 0.38 g/g sugars. This result demonstrates that C. glutamicum is a potential chassis for the industrial production of 1,3-PDO from abundant lignocellulosic feedstocks.     

不同pH调节剂对补料批式发酵产1,3-丙二醇的影响

对肺炎克雷伯氏菌（Klebsiellapneumoniae）发酵生产1,3-丙二醇（1,3-Propanediol,1,3．PD）的补碱策略进行了研究。分别利用NaOH、氨水、KOH三种溶液作为pH调节剂,优化三种pH调节剂并得到按一定比例混合的混合碱。当采用混合碱调控发酵pH值为7．0时,1,3-丙二醇的产量达到了55dL,比无pH调控（对照）发酵过程发酵水平提高了10．6倍。     

Use of ceramic-based cell immobilization to produce 1,3-propanediol from biodiesel-derived waste glycerol with Klebsiella pneumoniae

Aims: The feasibility of the continuous production of a valuable bioplastic raw material, namely 1,3‐propanediol (1,3‐PDO) from biodiesel by‐product glycerol, using immobilized cells was investigated. In addition, the effect of hydraulic retention time (HRT) was also analysed. Methods and Results: Ceramic balls and ceramic rings were used for the immobilization of a locally isolated strain; Klebsiella pneumoniae (GenBank no. 27F HM063413 ). HRT of 1 h is the best one in terms of volumetric production rate (g 1,3‐PDO l^?1 h^?1). The results indicated that ceramic‐based cell immobilization achieved a 2‐fold higher production rate (10 g 1,3‐PDO l^?1 h^?1) in comparison with suspended cell system (4·9 g 1,3‐PDO l^?1 h^?1). Conclusions: Continuous cultures with immobilized cells revealed that 1,3‐PDO production was more effective and more stable than suspended culture systems. Furthermore, cell immobilization had also obvious benefits especially for resistance of the production for extreme conditions (high organic loading rates, cell washouts). The results were important for understanding the significance of continuous immobilization process among other well‐known 1,3‐PDO fermentation processes. Significance and Impact of the Study: This work is a promising process for further studies, as the immobilized micro‐organism was able to reach high volumetric production rates at short HRT, it has an important role in tolerating and converting glycerol during fermentation. Therefore, HRT is a very significant operational parameter (P value <0·05) directly affecting the bioreactor performance and production rate.     

Inactivation of aldehyde dehydrogenase: a key factor for engineering 1,3-propanediol production by Klebsiella pneumoniae

Production of 1,3-propanediol (1,3-PD) from glycerol by Klebsiella pneumoniae is restrained by ethanol formation. The first step in the formation of ethanol from acetyl-CoA is catalyzed by aldehyde dehydrogenase (ALDH), an enzyme that competes with 1,3-PD oxidoreductase for the cofactor NADH. This study aimed to improve the production of 1,3-PD by engineering the ethanol formation pathway. An inactivation mutation of the aldA gene encoding ALDH in K. pneumoniae YMU2 was generated by insertion of a tetracycline resistance marker. Inactivation of ALDH resulted in a nearly abolished ethanol formation but a significantly improved 1,3-PD production. Metabolic flux analysis revealed that a pronounced redistribution of intracellular metabolic flux occurred. The final titer, the productivity of 1,3-PD and the yield of 1,3-PD relative to glycerol of the mutant strain reached 927.6 mmol L(-1), 14.05 mmol L(-1)h(-1) and 0.699 mol mol(-1), respectively, which were much higher than those of the parent strain. In addition, the specific 1,3-PD-producing capability (1,3-PD produced per gram of cells) of the mutant strain was 2-fold that of the parent strain due to a lower growth yield of the mutant. By increasing NADH availability, this study demonstrates an important metabolic engineering approach to improve the efficiency of oxidoreduction-coupled bioprocesses.     

Debottlenecking the 1,3-propanediol pathway by metabolic engineering

The history of 1,3-propanediol (1,3-PD) conversion from being a specialty chemical to being a bulk chemical illustrates that the concerted effort of different metabolic engineering approaches brings the most successful results. In order to metabolically tailor the 1,3-PD production pathway multiple strategies have been pursued. Knocking-out genes responsible for by-products formation, intergeneric transfer and overexpression of the genes directly involved in the pathway, manipulation with internal redox balance, introduction of a synthetic flux control point, and modification of the substrate mechanism of transport are some of the strategies applied. The metabolic engineering of the microbial 1,3-PD production exploits both native producers and microorganisms with acquired ability to produce the diol via genetic manipulations. Combination of the appropriate genes from homologous and heterologous hosts is expected to bring a desired objective of production of 1,3-PD cheaply, efficiently and independently from non-renewable resources. The state-of-the-art of the 1,3-PD pathway metabolic engineering is reviewed in this paper.     

Identification and utilization of a 1,3-propanediol oxidoreductase isoenzyme for production of 1,3-propanediol from glycerol in Klebsiella pneumoniae

In a previous study, we showed that 1,3-propanediol (1,3-PD) was still produced from glycerol by the Klebsiella pneumoniae mutant strain defective in 1,3-PD oxidoreductase (DhaT), although the production level was lower compared to the parent strain. As a potential candidate for another putative 1,3-PD oxidoreductase, we identified and characterized a homolog of Escherichia coli yqhD (88% homology in amino acid sequence), which encodes an alcohol dehydrogenase and is well known to replace the function of DhaT in E. coli. Introduction of multiple copies of the yqhD homolog restored 1,3-PD production in the mutant K. pneumoniae strain defective in DhaT. In addition, by-product formation was still eliminated in the recombinant strain due to the elimination of the glycerol oxidative pathway. An increase in NADP-dependent 1,3-PD oxidoreductase activity was observed in the recombinant strain harboring multiple copies of the yqhD homolog. The level of 1,3-PD production during batch fermentation in the recombinant strain was comparable to that of the parent strain; further engineering can generate an industrial strain producing 1,3-propanediol.     

Simultaneous production of 3-hydroxypropionic acid and 1,3-propanediol from glycerol by a recombinant strain of Klebsiella pneumoniae

In this study, an aldehyde dehydrogenase (ALDH) was over-expressed in Klebsiella pneumoniae for simultaneous production of 3-hydroxypropionic acid (3-HP) and 1,3-propanediol (1,3-PDO). Various genes encoding ALDH were cloned and expressed in K. pneumoniae, and expression of Escherichia colialdH resulted in the highest 3-HP titer in anaerobic cultures in shake flasks. Anaerobic fed-batch culture of this recombinant strain was further performed in a 5-L reactor. The 3-HP concentration and yield reached 24.4 g/L and 0.18 mol/mol glycerol, respectively, and at the same time 1,3-PDO achieved 49.3 g/L with a yield of 0.43 mol/mol in 24 h. The overall yield of 3-HP plus 1,3-PDO was 0.61 mol/mol. Over-expression of the E. coli AldH also reduced the yields of by-products except for lactate. This study demonstrated the possibility of simultaneous production of 3-HP and 1,3-PDO by K. pneumoniae under anaerobic conditions without supply of vitamin B₁₂.     

The effects of cell recycling on the production of 1,3-propanediol by Klebsiella pneumoniae

The effects of both biomass age and cell recycling on the 1,3-propanediol (1,3-PDO) production by Klebsiella pneumoniae were investigated in a membrane-supported bioreactor using hollow-fiber ultrafiltration membrane module in two separate experiments. It was determined that older cells have a negative effect on 1,3-PDO production. The concentrations of by-products, such as acetic acid and ethanol, increased in cultures with older cells, whereas the concentrations of succinic acid, lactic acid and 2,3-butanediol decreased. The effect of cell recycling was comparatively studied at a cell recycling ratio of 100 %. The results showed that cell recycling had also negative effects on 1,3-PDO fermentation. It was hypothesized that both cell recycling and biomass age caused metabolic shifts to undesired by-products which then inhibited the 1,3-PDO production. On the other hand, the use of hollow-fiber ultrafiltration membrane module was found to be very effective in terms of removal of cells from the fermentation broth.     

Study of two-stage processes for the microbial production of 1,3-propanediol from glucose

The microbial production of 1,3-propanediol (1,3-PD) from glucose was studied in a two-stage fermentation process on a laboratory scale. In the first stage, glucose was converted to glycerol either by the osmotolerant yeast Pichia farinosa or by a recombinant Escherichia coli strain. In the second stage, glycerol in the broth from the first stage was converted to 1,3-PD by Klebsiella pneumoniae. The culture broth from P. farinosa was shown to contain toxic metabolites that strongly impair the growth of K. pneumoniae and the formation of 1,3-PD. Recombinant E. coli is more suitable than P. farinosa for producing glycerol in the first stage. The fermentation pattern from glycerol can be significantly altered by the presence of acetate, leading to a significant reduction of PD yield in the second stage. However, in the recombinant E. coli culture acetate formation can be prevented by fed-batch cultivation under limiting glucose supply, resulting in an effective production of 1,3-PD in the second stage with a productivity of 2.0 g l(-1) h(-1) and a high yield (0.53 g/g) close to that of glycerol fermentation in a synthetic medium. The overall 1,3-PD yield from glucose in the two stage-process with E. coli and K. pneumoniae reached 0.17 g/g.     

Microbial production of 1,3-propanediol: Recent developments and emerging opportunities

1,3-Propanediol, a valuable bifunctional molecule, can be produced from renewable resources using microorganisms. It has several promising properties for many synthetic reactions, particularly for polymer and cosmetic industries. By virtue of being a natural product, relevant biochemical pathways can be harnessed into fermentation processes to produce 1,3-propanediol. Various strategies for the microbial production of 1,3-propanediol are reviewed and compared in this article with their promises and constraints. Furthermore, genetic and metabolic engineering could significantly improve product yields and overcome the limitations of fermentation technology. Present review gives an overview on 1,3-propanediol production by wild and recombinant strains. It also attempts to encompass the various issues concerned in utilization of crude glycerol for 1,3-propanediol production, with particular emphasis laid on biodiesel industries. This review also summarizes the present state of strategies studied for the downstream processing and purification of biologically produced 1,3-propanediol. The future prospect of 1,3-propanediol and its potential as a major bulk chemical are discussed under the light of the current research.     

Microbial production of 1,3-propanediol from glycerol by Klebsiella pneumoniae under micro-aerobic conditions up to a pilot scale

1,3-Propanediol (1,3-PD) can be produced from glycerol by Klebsiella pneumoniae under micro-aerobic conditions. Recently, this fed-batch fermentation process has been successfully scaled up to 1 m³. The final 1,3-PD concentration, molar yield and volumetric productivity of 72 g l⁻¹, 57% and 2.1 g l⁻¹ h⁻¹, respectively, are close to those of 75 g l⁻¹, 61%, and 2.2 g l⁻¹ h⁻¹ under anaerobic conditions. This process would be suitable for the production of 1,3-PD on a large scale.     

Coordination of metabolic pathways: Enhanced carbon conservation in 1,3-propanediol production by coupling with optically pure lactate biosynthesis

Metabolic engineering has emerged as a powerful tool for bioproduction of both fine and bulk chemicals. The natural coordination among different metabolic pathways contributes to the complexity of metabolic modification, which hampers the development of biorefineries. Herein, the coordination between the oxidative and reductive branches of glycerol metabolism was rearranged in Klebsiella oxytoca to improve the 1,3-propanediol production. After deliberating on the product value, carbon conservation, redox balance, biological compatibility and downstream processing, the lactate-producing pathway was chosen for coupling with the 1,3-propanediol-producing pathway. Then, the other pathways of 2,3-butanediol, ethanol, acetate, and succinate were blocked in sequence, leading to improved d-lactate biosynthesis, which as return drove the 1,3-propanediol production. Meanwhile, efficient co-production of 1,3-propanediol and l-lactate was also achieved by replacing ldhD with ldhL from Bacillus coagulans. The engineered strains PDL-5 and PLL co-produced over 70 g/L 1,3-propanediol and over 100 g/L optically pure d-lactate and l-lactate, respectively, with high conversion yields of over 0.95 mol/mol from glycerol.     

Physiologic mechanisms of sequential products synthesis in 1,3-propanediol fed-batch fermentation by Klebsiella pneumoniae

The glycerol fed-batch fermentation by Klebsiella pneumoniae CGMCC 1.6366 exhibited the sequential synthesis of products, including acetate, 1,3-propanediol (1,3-PD), 2,3-butanediol, ethanol, succinate, and lactate. The dominant flux distribution was shifted from acetate formation to 1,3-PD formation in early- exponential growth phase and then to lactate synthesis in late-exponential growth phase. The underlying physiological mechanism of the above observations has been investigated via the related enzymes, nucleotide, and intermediary metabolites analysis. The carbon flow shift is dictated by the intrinsic physiological state and enzymatic activity regulation. Especially, the internal redox state could serve as a rate-controlling factor for 1,3-PD production. The q(1,3-PD) formation was the combined outcomes of regulations of glycerol dehydratase activity and internal redox balancing. The q(ethanol)/q(acetate) ratios demonstrated the flexible adaptation mechanism of K. pneumoniae preferring ATP generation in early-exponential growth phase. A low PEP to pyruvate ratio corresponded LDH activity increase, leading to lactate accumulation in stationary phase.