Efficient solution‐processed double‐layer red OLEDs based on a new europium complex with a carbazole group

A new europium complex EuL₃(Phen) was used as guest dopant, and a blend of Polyvinylcarbazole and 2‐(biphenyl‐4‐yl)‐5‐(4‐tert‐butylphenyl)‐1,3,4‐oxadiazole (PVK and PBD) as host matrix. Efficient red organic light‐emitting devices (OLEDs) with double‐layer structures were manufactured via a solution‐processed technique. The guest‐doped levels were 1, 3 and 5 wt% relative to the blend mass, respectively. For the 1 wt% doping‐level device, the luminous efficiency and luminance were up to 2.96 cd/A and 635.78 cd/m² with emissions from both EuL₃(Phen) and from the host; for the 3 wt% doping‐level device, the maximum luminous efficiency and luminance were 1.01 cd/A and 370.91 cd/m² for the single emission from EuL₃(Phen) only. Copyright © 2014 John Wiley & Sons, Ltd.     

Scaling Printable Zn–Ag2O Batteries for Integrated Electronics

Printed batteries are an emerging solution for integrated energy storage using low‐cost, high accuracy fabrication techniques. While several printed batteries have been previously shown, few have designed a battery that can be incorporated into an integrated device. Specifically, a fully printed battery with a small active electrode area (<1 cm²) achieving high areal capacities (>10 mAh cm^?2) at high current densities (1–10 mA cm^?2) has not been demonstrated, which represents the minimum form‐factor and performance requirements for many low‐power device applications. This work addresses these challenges by investigating the scaling limits of a fully printed Zn–Ag₂O battery and determining the electrochemical limitations for a mm²‐scale battery. Processed entirely in air, Zn–Ag₂O batteries are well suited for integration in typical semiconductor packaging flows compared to lithium‐based chemistries. Printed cells with electrodes as small as 1 mm² maintain steady operating voltages above (>1.4 V) at high current densities (1–12 mA cm^?2) and achieve the highest reported areal capacity for a fully printed battery at 11 mAh cm^?2. The findings represent the first demonstration of a small, packaged, fully printed Zn–Ag₂O battery with high areal capacities at high current densities, a crucial step toward realizing chip‐scale energy storage for integrated electronic systems.     

A Cost Analysis of Fully Solution‐Processed ITO‐Free Organic Solar Modules

Organic photovoltaics (OPVs) have become a potential candidate for clean and renewable photovoltaic productions. This work examines the current cost drivers and potential avenues to reduce costs for organic solar modules by constructing a comprehensive bottom‐up cost model. The direct manufacturing cost (MC) and the minimum sustainable price (MSP) for an opaque single solar module (SSM) (MC = 187 ¥ m^?2, MSP = 297 ¥ m^?2) and for a tandem solar module (MC = 224 ¥ m^?2, MSP = 438 ¥ m^?2) are analyzed in detail. Within this calculation, the most expensive layers and processing steps are identified and highlighted. Importantly, the low levelized cost of energy (LCOE) value for an SSM with a 10% power conversion efficiency in a 20‐year range from 0.185 to 0.486 ¥ kWh^?1, with a national average of 0.324 ¥ kWh^?1 in China under an average solar irradiance of 1200 kWh m^?2 year^?1. Moreover, the impact on the cost of alternative materials and constructions, process throughputs, module efficiency, and module lifetime, etc., is presented and avenues to further reduce the MSP and LCOE values are indicated. The analysis shows that OPVs can emerge as a competitive alternative to established power generation technologies if the remaining issues (e.g., active layer material cost, module efficiency, and lifetime) can be resolved.     

Regulation of flowering by green light depends on its photon flux density and involves cryptochromes

Photoperiodic lighting can promote flowering of long‐day plants (LDPs) and inhibit flowering of short‐day plants (SDPs). Red (R) and far‐red (FR) light regulate flowering through phytochromes, whereas blue light does so primarily through cryptochromes. In contrast, the role of green light in photoperiodic regulation of flowering has been inconsistent in previous studies. We grew four LDP species (two petunia cultivars, ageratum, snapdragon and Arabidopsis) and two SDP species (three chrysanthemum cultivars and marigold) in a greenhouse under truncated 9‐h short days with or without 7‐h day‐extension lighting from green light (peak = 521 nm) at 0, 2, 13 or 25 μmol m^?2 s^?1 or R + white (W) + FR light at 2 μmol m^?2 s^?1. Increasing the green photon flux density from 0 to 25 μmol m^?2 s^?1 accelerated flowering of all LDPs and delayed flowering of all SDPs. Petunia flowered similarly fast under R + W + FR light and moderate green light but was shorter and developed more branches under green light. To be as effective as R + W + FR light, saturation green photon flux densities were 2 μmol m^?2 s^?1 for LDP ageratum and SDP marigold and 13 μmol m^?2 s^?1 for LDP petunia. Snapdragon was the least sensitive to green light. In Arabidopsis, cryptochrome 2 mediated promotion of flowering under moderate green light, whereas both phytochrome B and cryptochrome 2 mediated that under R + W + FR light. We conclude that 7‐h day‐extension lighting from green light‐emitting diodes can control flowering of photoperiodic ornamentals and that in Arabidopsis, cryptochrome 2 mediates promotion of flowering under green light.     

Monolithic Perovskite/Si Tandem Solar Cells: Pathways to Over 30% Efficiency

The article commences with a review focusing on three critical aspects of the perovskite/Si tandem technology: the evolution of efficiencies to date, comparisons of Si subcell choices, and the interconnection design strategies. Building on this review, a clear route is provided for minimizing optical losses aided by optical simulations of a recently reported high‐efficiency perovskite/Si tandem system, optimizations which result in tandem current densities of ≈20 mAcm^?2 with front‐side texture. The primary focus is on electrical modeling on the Si‐subcell, in order to understand the efficiency potential of this cell under filtered light in a tandem configuration. The possibility of increasing the Si subcell efficiency by 1% absolute is offered through joint improvements to the bulk lifetime, which exceeds 4 ms, and improves surface passivation quality to saturation current densities below 10 fA cm^?2. Polycrystalline‐Si/SiO_x passivating contacts are proposed as a promising alternative to partial‐area rear contacts, with the potential for further simplifying cell fabrication and improving device performance. A combination of optical modeling of the complete tandem structure alongside electrical modeling of the Si‐subcell, both with state‐of‐the‐art modeling tools, provides the first complete picture of the practical efficiency potential of perovskite/Si tandems.     

Critical flicker detection frequency and double pulse recognition threshold do not depend on the spectral properties of stimuli

We have measured the critical flicker detection frequency (CFDF) and double pulse recognition threshold (DPT) using three LEDs with power peaks at 460, 525 and 625 nm for target illumination. Brightness equalization was performed by customized heterochromatic flicker photometry (cHFP). Reference luminance levels were 170 cd/m² (blue LED, 60 subjects), 4 cd/m² (green LED, 20 subjects), and 1 cd/m² (green LED, 20 subjects). The measurement at 1 cd/m² was preceded by 15 min of dark adaptation. The angle of view for the target was 3°, and the duration of stimuli was 1 ms. An experimental pulse generator with three channels and a projector was used. No differences in CFDF at different spectral properties of stimulus were observed at all three levels of luminance. Thus, it is concluded that temporal vision resolution does not depend on the spectral properties of visual stimuli.     

Thin Film Encapsulation of Organic Solar Cells by Direct Deposition of Polysilazanes from Solution

Organic electronic devices (OEDs), e.g., organic solar cells, degrade quickly in the presence of ambient gases, such as water vapor and oxygen. Thus, in order to extend the lifetime of flexible OEDs, they have to be protected by encapsulation. A solution‐based encapsulation method is developed, which allows the direct deposition of the diffusion barrier on top of OEDs, thus avoiding lamination of barrier films. The method is based on the deposition of a perhydropolysilazane (PHPS) ink and its subsequent conversion into a silica layer by deep UV irradiation. The resulting barrier films show water vapor transmission rates (WVTRs) of <10^?2 g m^?2 d^?1 (40 °C/85% relative humidity (RH)) and oxygen transmission rates (OTRs) of <10^?2 cm³ m^?2 d^?1 bar^?1 at ambient conditions. Flexibility of the resulting barrier films is improved by coating a barrier stack of several thin PHPS layers alternating with organic polymer interlayers. These stacks show an increase of WVTR values by less than 10% after 3000 bending cycles. Direct coating of the PHPS films on top of organic solar cells enhances the device lifetime in damp heat conditions from a few hours to beyond 300 h.     

Paper‐Based Energy‐Storage Devices Comprising Carbon Fiber‐Reinforced Polypyrrole‐Cladophora Nanocellulose Composite Electrodes

Composites of polypyrrole (PPy) and Cladophora nanocellulose, reinforced with 8 μm‐thick chopped carbon filaments, can be used as electrode materials to obtain paper‐based energy‐storage devices with unprecedented performance at high charge and discharge rates. Charge capacities of more than 200 C g^?1 (PPy) are obtained for paper‐based electrodes at potential scan rates as high as 500 mV s^?1, whereas cell capacitances of ～60–70 F g^?1 (PPy) are reached for symmetric supercapacitor cells with capacitances up to 3.0 F (i.e.,0.48 F cm^?2) when charged to 0.6 V using current densities as high as 31 A g^?1 based on the PPy weight (i.e., 99 mA cm^?2). Energy and power densities of 1.75 Wh kg^?1 and 2.7 kW kg^?1, respectively, are obtained when normalized with respect to twice the PPy weight of the smaller electrode. No loss in cell capacitance is seen during charging/discharging at 7.7 A g^?1 (PPy) over 1500 cycles. It is proposed that the nonelectroactive carbon filaments decrease the contact resistances and the resistance of the reduced PPy composite. The present straightforward approach represents significant progress in the development of low‐cost and environmentally friendly paper‐based energy‐storage devices for high‐power applications.     

The contribution of single and double cones to spectral sensitivity in budgerigars during changing light conditions

Bird colour vision is mediated by single cones, while double cones and rods mediate luminance vision in bright and dim light, respectively. In daylight conditions, birds use colour vision to discriminate large objects such as fruit and plumage patches, and luminance vision to detect fine spatial detail and motion. However, decreasing light intensity favours achromatic mechanisms and eventually, in dim light, luminance vision outperforms colour vision in all visual tasks. We have used behavioural tests in budgerigars (Melopsittacus undulatus) to investigate how single cones, double cones and rods contribute to spectral sensitivity for large (3.4°) static monochromatic stimuli at light intensities ranging from 0.08 to 63.5 cd/m². We found no influences of rods at any intensity level. Single cones dominate the spectral sensitivity function at intensities above 1.1 cd/m², as predicted by a receptor noise-limited colour discrimination model. Below 1.1 cd/m², spectral sensitivity is lower than expected at all wavelengths except 575 nm, which corresponds to double cone function. We suggest that luminance vision mediated by double cones restores visual sensitivity when single cone sensitivity quickly decreases at light intensities close to the absolute threshold of colour vision.     

Rational Design of Nickel Hydroxide‐Based Nanocrystals on Graphene for Ultrafast Energy Storage

Compact, light, and powerful energy storage devices are urgently needed for many emerging applications; however, the development of advanced power sources relies heavily on advances in materials innovation. Here, the findings in rational design, one‐pot synthesis, and characterization of a series of Ni hydroxide‐based electrode materials in alkaline media for fast energy storage are reported. Under the guidance of density functional theory calculations and experimental investigations, a composite electrode composed of Co‐/Mn‐substituted Ni hydroxides grown on reduced graphene oxide (rGO) is designed and prepared, demonstrating capacities of 665 and 427 C g^?1 at current densities of 2 and 20 A g^?1, respectively. The superior performance is attributed mainly to the low deprotonation energy and the facile electron transport, as elaborated by theoretical calculations. When coupled with an electrode based on organic molecular‐modified rGO, the resulting hybrid device demonstrates an energy density of 74.7 W h kg^?1 at a power density of 1.68 kW kg^?1 while maintaining capacity retention of 91% after 10,000 cycles (20 A g^?1). The findings not only provide a promising electrode material for high‐performance hybrid capacitors but also open a new avenue toward knowledge‐based design of efficient electrode materials for other energy storage applications.     

Visual acuity and spatial contrast sensitivity in tree squirrels

The visual sensitivity of tree squirrels from three different species (two western gray squirrels, Sciurus griseus; three fox squirrels, Sciurus niger; and an eastern gray squirrel, Sciurus carolinensis) was measured for spatial patterns defined by luminance differences. Spatial contrast sensitivity functions were determined in behavioral discrimination experiments in which the stimuli were sinusoidally-modulated gratings. At an average luminance level of 3.4 cd/m² these squirrels were maximally sensitive to spatial frequencies of about 0.5 cycles/degree (c/d). These experiments, in conjunction with additional measurements involving discrimination of square-wave grating patterns, also indicate that the finest gratings these squirrels can discriminate average 2.2 c/d (SD = 0.42 c/d). There are no obvious differences in resolution acuity among the three species. Grating acuity also was measured at a much higher luminance level (340 cd/m²). The results of this experiment indicate that the spatial acuity of the tree squirrel increases with luminance level, reaching a maximum of 3.9 c/d at 340 cd/m².     

Facile and Scalable Preparation of Ruthenium Oxide‐Based Flexible Micro‐Supercapacitors

Tremendous efforts have been invested in the development of the internet of things during the past 10 years. Implantable sensors still need embedded miniaturized energy harvesting devices, since commercialized thin films and microbatteries do not provide sufficient power densities and suffer from limited lifetime. Therefore, micro‐supercapacitors are good candidates to store energy and deliver power pulses while providing non‐constant voltage output with time. However, multistep expensive protocols involving mask aligners and sophisticated cleanrooms are used to prepare these devices. Here, a simple and versatile laser‐writing procedure to integrate flexible micro‐supercapacitors and microbatteries on current‐collector‐free polyimide foils is reported, starting from commercial powders. Ruthenium oxide (RuO₂)‐based micro‐supercapacitors are prepared by laser irradiation of a bilayered tetrachloroauric acid (HAuCl₄ · 3H₂O)–cellulose acetate/RuO₂ film deposited by spin‐coating, which leads to adherent Au/RuO₂ electrodes with a unique pillar morphology. The as‐prepared microdevices deliver 27 mF cm^?2/540 F cm^?3 in 1 m H₂SO₄ and retain 80% of the initial capacitance after 10 000 cycles. This simple process is applied to make carbon‐based micro‐supercapacitors, as well as metal oxide based pseudocapacitors and battery electrodes, thus offering a straightforward solution to prepare low‐cost flexible microdevices at a large scale.     

Age-related changes in pattern visual evoked potentials: differential effects of luminance,contrast and check size

We recorded visual evoked potentials (VEPs) to checkerboard pattern-reversal stimulation in 109 normal subjects (51 males and 59 females; aged 19–84 years) in order to study the aging effect on the multiple channels of the visual system in humans. Transient VEPs to 3 check sizes (15′, 30′ and 50′) were obtained by monocular stimulation. Two test conditions were employed: (1) a high luminance (180 cd/m²) and a low luminance (11 cd/m²) both with a fixed contrast (90%), and (2) a high contrast (85%) and a low contrast (10%) both at a fixed luminance (57 cd/m²). The major features of our results included: (1) the presence of a curvilinear relationship between P100 latency and age for all conditions, while the P100 amplitude did not show any such aging effect, (2) the age-latency function was similar between the two luminance conditions, while it was different between the two contrast conditions, and (3) the differential age effect on the P100 latency caused by changes in contrast depended on the check size. These results suggest that age-related changes in the human visual system are not uniform, but rather are different in the specific functional subdivisions. It is thus hypothesized that aging may differentially influence the separate channels of the human visual system.     

High‐Performance Relaxor Ferroelectric Materials for Energy Storage Applications

Relaxor ferroelectrics usually possess low remnant polarizations and slim hystereses, which can provide high saturated polarizations and superior energy conversion efficiencies, thus receiving increasing interest as energy storage materials with high discharge energy densities and fast discharge ability. In this study, a relaxor ferroelectric multilayer energy storage ceramic capacitor (MLESCC) based on 0.87BaTiO₃‐0.13Bi(Zn_2/3(Nb_0.85Ta_0.15)_1/3)O₃ (BT‐BZNT) with inexpensive Ag/Pd inner electrodes is prepared by the tape casting method. The MLESCC with two dielectric layers (layer thicknesses of 5 µm) sintered by a two‐step sintering method exhibits excellent energy storage properties with a record‐high discharge energy density of 10.12 J cm^?3, a high energy efficiency of 89.4% achieved at an electric field of 104.7 MV m^?1, a high temperature stability of the energy storage density (with minimal variation of <±5%), and energy efficiency (>90%) over a range of ?75 to 150 °C at 40 MV m^?1. These results suggest that the BT‐BZNT relaxor ferroelectric ceramic material can provide realistic solutions for high‐power energy storage capacitors.     

All‐Solid‐State On‐Chip Supercapacitors Based on Free‐Standing 4H‐SiC Nanowire Arrays

All‐solid‐state on‐chip SiC supercapacitors (SCs) based on free‐standing SiC nanowire arrays (NWAs) are reported. In comparison to the widely used technique based on the interdigitated fingers, the present strategy can be much more facile for constructing on‐chip SCs devices, which is directly sandwiched with a solid electrolyte layer between two pieces of SiC NWAs film without any substrate. The mass loading of active materials of on‐chip SiC SCs can be up to ≈5.6 mg cm^?2, and the total device thickness is limited in ≈40 µm. The specific area energy and power densities of the SCs device reach 5.24 µWh cm^?2 and 11.2 mW cm^?2, and their specific volume energy and power densities run up to 1.31 mWh cm^–3 and 2.8 W cm^?3, respectively, which are two orders of magnitude higher than those of state‐of‐the‐art SiC‐based SCs, and also much higher than those of other solid‐state carbon‐based SCs ever reported. Furthermore, such on‐chip SCs exhibit superior rate capability and robust stability with over 94% capacitance retention after 10 000 cycles at a scan rate of 100 mV s^?1, representing their high performance in all merits.     

Efficient blue organic light‐emitting diodes using N2,N2,N11,N11,5,6,7,8‐octaphenyltriphenylene‐2,11‐diamine derivatives

In this study, we have synthesized phenyl‐substituted triphenylene derivatives, using the Diels–Alder reaction and the Buchwald–Hartwig reaction. To investigate electroluminescence properties of these materials, multilayer organic light‐emitting diode (OLED) devices were fabricated with a structure of indium–tin–oxide (ITO) (180 nm)/4,4′‐bis(N‐(1‐naphthyl)‐N‐phenylamino)biphenyl (NPB) (50 nm)/blue‐emitting materials (1–3) (30 nm)/bathophenanthroline (Bphen) (35 nm)/lithium quinolate (Liq) (2 nm)/Al (100 nm). A device using N²,N²,N¹¹,N¹¹,5,6,7‐heptaphenyltriphenylene‐2,11‐diamine (2) exhibited efficient blue emission with luminous, power, and external quantum efficiencies of 0.92 cd/A, 0.67 lm/W, and 1.17% at 20 mA/cm², respectively. The Commission International de L'Éclairage coordinates of this device were (x = 0.15, y = 0.09) at 6.0 V. Copyright © 2015 John Wiley & Sons, Ltd.     

3D Vertically Aligned Li Metal Anodes with Ultrahigh Cycling Currents and Capacities of 10 mA cm−2/20 mAh cm−2 Realized by Selective Nucleation within Microchannel Walls

Although metallic lithium is regarded as the “Holy Grail” for next‐generation rechargeable batteries due to its high theoretical capacity and low overpotential, the uncontrollable Li dendrite growth, especially under high current densities and deep plating/striping, has inhibited its practical application. Herein, a 3D‐printed, vertically aligned Li anode (3DP‐VALi) is shown to efficiently guide Li deposition via a “nucleation within microchannel walls” process, enabling a high‐performance, dendrite‐free Li anode. Moreover, the microchannels within the microwalls are beneficial for promoting fast Li⁺ diffusion, supplying large space for the accommodation of Li during the plating/stripping process. The high‐surface‐area 3D anode design enables high operating current densities and high areal capacities. As a result, the Li–Li symmetric cells using 3DP‐VALi demonstrate excellent electrochemical performances as high as 10 mA cm^?2/10 mAh cm^?2 for 1500 h and 5 mA cm^?2/20 mAh cm^?2 for 400 h, respectively. Additionally, the Li–S and Li–LiFePO₄ cells using 3DP‐VALi anodes present excellent cycling stability up to 250 and 800 cycles at a rate of 1 C, respectively. It is believed that these new findings could open a new window for dendrite‐free metal anode design and pave the way toward energy storage devices with high energy/power density.     

Comparison of four outdoor pilot-scale photobioreactors

Background

Microalgae are a potential source of sustainable commodities of fuels, chemicals and food and feed additives. The current high production costs, as a result of the low areal productivities, limit the application of microalgae in industry. A first step is determining how the different production system designs relate to each other under identical climate conditions. The productivity and photosynthetic efficiency of Nannochloropsis sp. CCAP 211/78 cultivated in four different outdoor continuously operated pilot-scale photobioreactors under the same climatological conditions were compared. The optimal dilution rate was determined for each photobioreactor by operation of the different photobioreactors at different dilution rates.

Results

In vertical photobioreactors, higher areal productivities and photosynthetic efficiencies, 19–24 g m^?2 day^?1 and 2.4–4.2 %, respectively, were found in comparison to the horizontal systems; 12–15 g m^?2 day^?1 and 1.5–1.8 %. The higher ground areal productivity in the vertical systems could be explained by light dilution in combination with a higher light capture. In the raceway pond low productivities were obtained, due to the long optical path in this system. Areal productivities in all systems increased with increasing photon flux densities up to a photon flux density of 30 mol m^?2 day^?1. Photosynthetic efficiencies remained constant in all systems with increasing photon flux densities. The highest photosynthetic efficiencies obtained were; 4.2 % for the vertical tubular photobioreactor, 3.8 % for the flat panel reactor, 1.8 % for the horizontal tubular reactor, and 1.5 % for the open raceway pond.

Conclusions

Vertical photobioreactors resulted in higher areal productivities than horizontal photobioreactors because of the lower incident photon flux densities on the reactor surface. The flat panel photobioreactor resulted, among the vertical photobioreactors studied, in the highest average photosynthetic efficiency, areal and volumetric productivities due to the short optical path. Photobioreactor light interception should be further optimized to maximize ground areal productivity and photosynthetic efficiency.

     

Battery‐like Supercapacitors from Vertically Aligned Carbon Nanofiber Coated Diamond: Design and Demonstrator

To fabricate battery‐like supercapacitors with high power and energy densities, big capacitances, as well as long‐term capacitance retention, vertically aligned carbon nanofibers (CNFs) grown on boron doped diamond (BDD) films are employed as the capacitor electrodes. They possess large surface areas, high conductivity, high stability, and importantly are free of binder. The large surface areas result from their porous structures. The containment of graphene layers and copper metal catalysts inside CNFs leads to their high conductivity. Both electrical double layer capacitors (EDLCs) in inert solutions and pseudocapacitors (PCs) using Fe(CN)₆^3?/4? redox‐active electrolytes are constructed with three‐ and two‐electrode systems. The assembled two‐electrode symmetrical supercapacitor devices exhibit capacitances of 30 and 48 mF cm^?2 at 10 mV s^?1 for EDLC and PC devices, respectively. They remain constant even after 10 000 charging/discharging cycles. The power densities are 27.3 and 25.3 kW kg^?1 for EDLC and PC devices, together with their energy densities of 22.9 and 44.1 W h kg^?1, respectively. The performance of these devices is superior to most of the reported supercapacitors and batteries. Vertically aligned CNF/BDD hybrid films are thus useful to construct high‐performance battery‐like and industry‐orientated supercapacitors for future power devices.     

Electrocatalytic Reduction of Gaseous CO2 to CO on Sn/Cu‐Nanofiber‐Based Gas Diffusion Electrodes

Earth‐abundant Sn/Cu catalysts are highly selective for the electrocatalytic reduction of CO₂ to CO in aqueous electrolytes. However, CO₂ mass transport limitations, resulting from the low solubility of CO₂ in water, so far limit the CO partial current density for Sn/Cu catalysts to about 10 mA cm^?2. Here, a freestanding gas diffusion electrode design based on Sn‐decorated Cu‐coated electrospun polyvinylidene fluoride nanofibers is demonstrated. The use of gaseous CO₂ as a feedstock alleviates mass transport limitations, resulting in high CO partial current densities above 100 mA cm^?2, while maintaining high CO faradaic efficiencies above 80%. These results represent an important step toward an economically viable pathway to CO₂ reduction.