Modulation of End Groups for Low‐Bandgap Nonfullerene Acceptors Enabling High‐Performance Organic Solar Cells

The field of nonfullerene organic solar cells (OSCs) has seen an impressive progress, largely due to advances in high‐performance small molecule acceptors (SMAs). As a large portion of the solar energy is located in the near‐infrared region, it is important to develop ultralow‐bandgap SMAs that have extended absorption in the spectral range of 800–1000 nm to maximize light absorption and efficiencies. In this work, three low‐bandgap SMAs, namely, IXIC, IXIC‐2Cl, and IXIC‐4Cl, are designed and synthesized with same fused terthieno[3,2‐b]thiophene donor unit and different end groups (EGs). The three SMAs all have low optical bandgap (E_g) of 1.35, 1.30, and 1.25 eV, respectively. The chlorination on EGs can lower the energy level and broaden absorption range of the SMAs. As a result, the V_oc of the devices is reduced but the J_sc is significantly increased. In addition, the addition of chlorine atoms can enhance π–π stacking and crystallinity of the SMAs, which result in high fill factors. Overall, the optimum EGs are monochlorine‐substituted IC and OSCs based on PBDB‐T:IXIC‐2Cl that can achieve remarkable power conversion efficiencies (PCEs) of 12.2%, which is one of the highest PCEs for nonfullerene organic solar cells based on low‐bandgap SMAs.     

Morphological Characterization of a Low‐Bandgap Crystalline Polymer:PCBM Bulk Heterojunction Solar Cells

Understanding the morphology of polymer‐based bulk heterojunction (BHJ) solar cells is necessary to improve device efficiencies. Blends of a low‐bandgap silole‐containing conjugated polymer, poly[(4,4′‐bis(2‐ethylhexyl)dithieno[3,2‐b;2′,3′‐d]silole)‐2,6‐diyl‐alt‐(4,7‐bis(2‐thienyl)‐2,1,3‐benzothiadiazole)‐5,5′‐diyl] (PSBTBT) with [6,6]phenyl‐C61‐butyric acid methyl ester (PCBM) were investigated under different processing conditions. The surface morphologies and vertical segregation of the “As‐Spun”, “Pre‐Annealed”, and “Post‐Annealed” films were studied by scanning force microscopy, contact angle measurements, X‐ray photoelectron spectroscopy, near‐edge X‐ray absorption fine structure spectroscopy, dynamic secondary ion mass spectrometry, and neutron reflectivity. The results showed that PSBTBT was enriched at the cathode interface in the “As‐Spun” films and thermal annealing increased the segregation of PSBTBT to the free surface, while thermal annealing after deposition of the cathode increased the PCBM concentration at the cathode interface. Grazing‐incidence X‐ray diffraction and small‐angle neutron scattering showed that the crystallization of PSBTBT and segregation of PCBM occurred during spin coating, and thermal annealing increased the ordering of PSBTBT and enhanced the segregation of the PCBM, forming domains ～10 nm in size, leading to an improvement in photovoltaic performance.     

High‐Performance Ta2O5/Al‐Doped Ag Electrode for Resonant Light Harvesting in Efficient Organic Solar Cells

A efficient indium tin oxide (ITO)‐free transparent electrode based on an improved Ag film is designed by introducing small amount of Al during co‐deposition, producing ultrathin and smooth Ag film with low loss. A transparent electrode as thin as 4 nm is achieved by depositing the film on top of Ta₂O₅ layer, and organic solar cells based on such ultrathin electrode are built, producing power conversion efficiency over 7%. The device efficiency can be optimized by simply tuning Ta₂O₅ layer thickness external to the organic photovoltaic (OPV) structure to create an optical cavity resonance inside the photoactive layer. Therefore Ta₂O₅/Al‐doped Ag films function as a high‐performance electrode with high transparency, low resistance, improved photon management capability and mechanical flexibility.     

Solution‐Processed Low‐Bandgap CuIn(S,Se)2 Absorbers for High‐Efficiency Single‐Junction and Monolithic Chalcopyrite‐Perovskite Tandem Solar Cells

A novel molecular‐ink deposition route based on thiourea and N,N‐dimethylformamide (DMF) that results in a certified solar cell efficiency world record for non‐vacuum deposited CuIn(S,Se)₂ (CIS) absorbers and non‐vacuum deposited absorbers with a bandgap of 1.0 eV, is presented. It is found that by substituting the widely employed solvent dimethyl sulfoxide with DMF, the coordination chemistry of InCl₃ could be altered, dramatically improving ink stability, enabling up to tenfold increased concentrations, omitting the necessity for elevated ink temperatures, and radically accelerating the deposition process. Furthermore, it is shown that by introducing compositionally graded precursor films, film porosity, compositional gradients, and the surface roughness of the absorbers are effectively reduced and device conversion efficiencies are increased up to 13.8% (13.1% certified, active area). The reduced roughness is also seen as crucial to realize monolithically interconnected CIS‐perovskite tandem devices, where semitransparent MAPbI₃ devices are directly deposited on the CIS bottom cell. Confirming the feasibility of this approach, monolithic devices with near perfect voltage addition between subcells of up to 1.40 V are presented.     

Efficiency Enhancement of Polymer Solar Cells Based on Poly(3‐hexylthiophene)/Indene‐C70 Bisadduct via Methylthiophene Additive

Photovoltaic performance of polymer solar cells based on poly(3‐hexylthiophene) (P3HT) as the donor and indene‐C₇₀ bisadduct (IC₇₀BA) as the acceptor is improved by adding 3 vol% 3‐methylthiophene (MT) or 3‐hexylthiophene (HT) as processing additives. The results of UV‐vis absorption spectroscopy, X‐ray diffraction analysis and atomic force microscopy indicate that with the MT or HT processing additive, the active layer of the blend of P3HT/IC₇₀BA showed strengthened absorbance, enhanced crystallinity and improved film morphology. The power conversion efficiency (PCE) of the PSCs was improved from 5.80% for the device without the additive to 6.35% for the device with HT additive and to 6.69% with MT additive. The PCE of 6.69% is the top value reported so far for the PSCs based on P3HT.     

Efficient CH3NH3PbI3 Perovskite Solar Cells Based on Graphdiyne (GD)‐Modified P3HT Hole‐Transporting Material

Novel large π‐conjugated carbon material, graphdiyne (GD), as a dopant to poly(3‐hexylthiophene) (P3HT) hole‐transporting material (HTM) layer, is introduced into perovskite solar cells for the first time. Raman spectroscopy and ultraviolet photoelectron spectroscopy measurements reveal that relatively strong π–π stacking interaction occurs between GD particles and P3HT (so‐called P3HT/GD composite HTM), favorable for the hole transportation and improvement of the cell performance. On the other hand, some GD aggregates exhibit a scattering nature, and thus help to increase the light absorption of the perovskite solar cells in the long wavelength range. As high as 14.58% light‐to‐electricity conversion efficiency is achieved, superior to the pristine P3HT‐based devices. Additionally, the devices exhibit good stability and reproducibility. Time‐resolved photoluminescence decay measurements reveal that the P3HT/GD HTM can accelerate the hole extraction compared with pristine P3HT.     

Vacuum‐Assisted Growth of Low‐Bandgap Thin Films (FA0.8MA0.2Sn0.5Pb0.5I3) for All‐Perovskite Tandem Solar Cells

All‐perovskite multijunction photovoltaics, combining a wide‐bandgap (WBG) perovskite top solar cell (E_G ≈1.6–1.8 eV) with a low‐bandgap (LBG) perovskite bottom solar cell (E_G < 1.3 eV), promise power conversion efficiencies (PCEs) >33%. While the research on WBG perovskite solar cells has advanced rapidly over the past decade, LBG perovskite solar cells lack PCE as well as stability. In this work, vacuum‐assisted growth control (VAGC) of solution‐processed LBG perovskite thin films based on mixed Sn–Pb perovskite compositions is reported. The reported perovskite thin films processed by VAGC exhibit large columnar crystals. Compared to the well‐established processing of LBG perovskites via antisolvent deposition, the VAGC approach results in a significantly enhanced charge‐carrier lifetime. The improved optoelectronic characteristics enable high‐performance LBG perovskite solar cells (1.27 eV) with PCEs up to 18.2% as well as very efficient four‐terminal all‐perovskite tandem solar cells with PCEs up to 23%. Moreover, VAGC leads to promising reproducibility and potential in the fabrication of larger active‐area solar cells up to 1 cm².     

Morphology‐Limited Free Carrier Generation in Donor/Acceptor Polymer Blend Solar Cells Composed of Poly(3‐hexylthiophene) and Fluorene‐Based Copolymer

The charge generation and recombination dynamics in polymer/polymer blend solar cells composed of poly(3‐hexylthiophene) (P3HT, electron donor) and poly[2,7‐(9,9‐didodecylfluorene)‐alt‐5,5‐(4′,7′‐bis(2‐thienyl)‐2′,1′,3′‐benzothiadiazole)] (PF12TBT, electron acceptor) are studied by transient absorption measurements. In the unannealed blend film, charge carriers are efficiently generated from polymer excitons, but some of them recombine geminately. In the blend film annealed at 160 °C, on the other hand, the geminate recombination loss is suppressed and hence free carrier generation efficiency increases up to 74%. These findings suggest that P3HT and PF12TBT are intermixed within a few nanometers, resulting in impure PF12TBT and disordered P3HT domains. The geminate recombination is likely due to charge carriers generated on isolated polymer chains in the matrix of the other polymer and at the domain interface with disordered P3HT. The undesired charge loss by geminate recombination is reduced by both the purification of the PF12TBT‐rich domain and crystallization of the P3HT chains. These results show that efficient free carrier generation is not inherent to the polymer/fullerene domain interface, but is possible with polymer/polymer systems composed of crystalline donor and amorphous acceptor polymers, opening up a new potential method for the improvement of solar cell materials.     

High‐Performance Thick‐Film All‐Polymer Solar Cells Created Via Ternary Blending of a Novel Wide‐Bandgap Electron‐Donating Copolymer

A novel wide‐bandgap electron‐donating copolymer containing an electron‐deficient, difluorobenzotriazole building block with a siloxane‐terminated side chain is developed. The resulting polymer, poly{(4,8‐bis(4,5‐dihexylthiophen‐2‐yl)benzo[1,2‐b:4,5‐b′]dithiophene‐co‐4,7‐di(thiophen‐2‐yl)‐5,6‐difluoro‐2‐(6‐(1,1,1,3,5,5,5‐heptamethyltri‐siloxan‐3‐yl)hexyl)‐2H‐benzo[d][1,2,3]triazole} (PBTA‐Si), is used to successfully fabricate high‐performance, ternary, all‐polymer solar cells (all‐PSCs) insensitive to the active layer thickness. An impressively high fill factor of ≈76% is achieved with various ternary‐blending ratios. The optimized all‐PSCs attain a power conversion efficiency (PCE) of 9.17% with an active layer thickness of 350 nm and maintain a PCE over 8% for thicknesses over 400 nm, which is the highest reported efficiency for thick all‐PSCs. These results can be attributed to efficient charge transfer, additional energy transfer, high and balanced charge transport, and weak recombination behavior in the photoactive layer. Moreover, the photoactive layers of the ternary all‐PSCs are processed in a nonhalogenated solvent, 2‐methyltetrahydrofuran, which greatly improves their compatibility with large‐scale manufacturing.     

High‐Performance Perovskite Solar Cells with Enhanced Environmental Stability Based on a (p‐FC6H4C2H4NH3)2[PbI4] Capping Layer

Supported by the density functional theory (DFT) calculations, for the first time, a fluorinated aromatic cation, 2‐(4‐fluorophenyl)ethyl ammonium iodide (FPEAI), is introduced to grow in situ a low dimensional perovskite layer atop 3D perovskite film with excess PbI₂. The resulted (p‐FC₆H₄C₂H₄NH₃)₂[PbI₄] perovskite functions as a protective capping layer to protect the 3D perovskite from moisture. In the meantime, the thin layer facilitates charge transfer at the interfaces, thereby reducing the nonradiative recombination pathways. Laser scanning confocal microscopy unveils visually the distribution of the 2D perovskite layer on top of the 3D perovskite. When employing the 3D–2D perovskite as the absorbing layer in the photovoltaic cells, a high power conversion efficiency of 20.54% is realized. Superior device performance and moisture stability are observed with the modified perovskite over the whole stability test period.     

Medium Bandgap Polymer Donor Based on Bi(trialkylsilylthienyl‐benzo[1,2‐b:4,5‐b′]‐difuran) for High Performance Nonfullerene Polymer Solar Cells

A new 2D‐conjugated medium bandgap donor–acceptor copolymer, J81 , based on benzodifuran with trialkylsilyl thiophene side chains as donor unit and fluorobenzothiazole as acceptor, is synthesized and successfully used in nonfullerene polymer solar cells (PSCs) with low bandgap n‐type organic semiconductor (n‐OS) 3,9‐bis(2‐methylene‐ (3‐(1,1‐dicyanomethylene)‐indanone)‐5,5,11,11‐tetrakis(4‐ hexylphenyl)‐dithieno[2,3‐d:2′,3′‐d′]‐s‐indaceno[1,2‐b:5,6‐b′]‐ dithiophene (ITIC) and m ‐ITIC as acceptor. J81 possesses a lower‐lying highest occupied molecular orbital (HOMO) energy level of ?5.43 eV and medium bandgap of 1.93 eV with complementary absorption in the visible–near infrared region with the n‐OS acceptor. The PSCs based on J81 :ITIC and J81 :m ‐ITIC yield high power conversion efficiency of 10.60% and 11.05%, respectively, with high V _oc of 0.95–0.96 V benefit from the lower‐lying HOMO energy level of J81 donor. The work indicates that J81 is another promising polymer donor for the nonfullerene PSCs.     

A High‐Performance D–A Copolymer Based on Dithieno[3,2‐b:2′,3′‐d]Pyridin‐5(4H)‐One Unit Compatible with Fullerene and Nonfullerene Acceptors in Solar Cells

Development of high‐performance donor–acceptor (D–A) copolymers is vital in the research of polymer solar cells (PSCs). In this work, a low‐bandgap D–A copolymer based on dithieno[3,2‐b:2′,3′‐d]pyridin‐5(4H)‐one unit (DTP), PDTP4TFBT, is developed and used as the donor material for PSCs with PC₇₁BM or ITIC as the acceptor. PDTP4TFBT:PC₇₁BM and PDTP4TFBT:ITIC solar cells give power conversion efficiencies (PCEs) up to 8.75% and 7.58%, respectively. 1,8‐Diiodooctane affects film morphology and device performance for fullerene and nonfullerene solar cells. It inhibits the active materials from forming large domains and improves PCE for PDTP4TFBT:PC₇₁BM cells, while it promotes the aggregation and deteriorates performance for PDTP4TFBT:ITIC cells. The ternary‐blend cells based on PDTP4TFBT:PC₇₁BM:ITIC (1:1.2:0.3) give a decent PCE of 9.20%.