High Capacity All‐Solid‐State Lithium Batteries Enabled by Pyrite‐Sulfur Composites

As the theoretical limit of intercalation material‐based lithium‐ion batteries is approached, alternative chemistries based on conversion reactions are presently considered. The conversion of sulfur is particularly appealing as it is associated with a theoretical gravimetric energy density up to 2510 Wh kg^?1. In this paper, three different carbon‐iron disulfide‐sulfur (C‐FeS₂‐S) composites are proposed as alternative positive electrode materials for all‐solid‐state lithium‐sulfur batteries. These are synthesized through a facile, low‐cost, single‐step ball‐milling procedure. It is found that the crystalline structure (evaluated by X‐ray diffraction) and the morphology of the composites (evaluated by scanning electron microscopy) are greatly influenced by the FeS₂:S ratio. Li/LiI‐Li₃PS₄/C‐FeS₂‐S solid‐state cells are tested under galvanostatic conditions, while differential capacity plots are used to discuss the peculiar electrochemical features of these novel materials. These cells deliver capacities as high as 1200 mAh g_(FeS2+S)^?1 at the intermediate loading of 1 mg cm^?2 (1.2 mAh cm^?2), and up to 3.55 mAh cm^?2 for active material loadings as high as 5 mg cm^?2 at 20 °C. Such an excellent performance, rarely reported for (sulfur/metal sulfide)‐based, all solid‐state cells, makes these composites highly promising for real application where high positive electrode loadings are required.     

Optimized 4‐V Spinel Cathode Material with High Energy Density for Li‐Ion Cells Operating at 60 °C

Spinel cathodes comprising 16‐μm, AlPO₄‐coated Li_1.09Mn_1.83Al_0.08O₄ with a high energy density of 1.2 W h cm^‐3 are synthesized via a conventional solid‐state reaction using MnO₂ and Li₂CO₃ at 770 °C for 10 h and using a solution‐based coating method in bulk scale (>20 kg). The cathodes are coated by aluminum phosphate at a thickness of <10 nm. The coated cathodes exhibit a first discharge capacity of 108 mA·h g^‐1 and a coulombic efficiency of >99.8%, and their capacity retention is 78% after 200 cycles at a 0.5C rate in a Li‐ion cell under 60 °C. More importantly, a Li‐ion cell containing the coated cathode does not exhibit a swelling problem after 200 cycles at 60 °C. Transmission and scanning electron microscopy suggest that the uniformly distributed AlPO₄ coating and the possible formation of a solid solution phase along the surface play key roles in enhancing the electrochemical performance of the LiMn₂O₄ spinel at 60 °C.     

Mixed Phase Solid‐State Plastic Crystal Electrolytes Based on a Phosphonium Cation for Sodium Devices

Na batteries are seen as a feasible alternative technology to lithium ion batteries due to the greater abundance of sodium and potentially similar electrochemical behavior. In this work, mixed phase electrolyte materials based on solid‐state compositions of a tri methylisobutylphosphonium (P_111i4) bis(tri fluromethanesulphonyl)amide (NTf₂) organic ionic plastic crystal (OIPC) and high concentration of NaNTf₂ that support safe, sodium metal electrochemistry are demonstrated. A Na symmetric cell can be cycled efficiently, even in the solid state (at 50 °C and 60 °C), for a 25 mol% (P_111i4NTf₂)–75 mol% NaNTf₂ composition at 0.1 mA cm^?2 for 100 cycles. Thus, these mixed phase materials can be potentially used in Na‐based devices under moderate temperature conditions. It is also investigated that the phase behavior, conductivity, and electrochemical properties of mixtures of NaNTf₂ with this OIPC. It is observed that these mixtures have complex phase behavior. For high compositions of the Na salt, the materials are solid at room temperature and retain a soft solid consistency even at 50 °C with remarkably high conductivity, approaching that of the pure ionic liquid at 50 °C, i.e., 10^?3–10^?2 S cm^?1.     

Fast and Stable Proton Conduction in Heavily Scandium‐Doped Polycrystalline Barium Zirconate at Intermediate Temperatures

The environmental benefits of fuel cells and electrolyzers have become increasingly recognized in recent years. Fuel cells and electrolyzers that can operate at intermediate temperatures (300–450 °C) require, in principle, neither the precious metal catalysts that are typically used in polymer‐electrolyte‐membrane systems nor the costly heat‐resistant alloys used in balance‐of‐plant components of high‐temperature solid oxide electrochemical cells. These devices require an electrolyte with high ionic conductivity, typically more than 0.01 S cm^?1, and high chemical stability. To date, however, high ionic conductivities have been found in chemically unstable materials such as CsH₂PO₄, In‐doped SnP₂O₇, BaH₂, and LaH_3?2xO_x. Here, fast and stable proton conduction in 60‐at% Sc‐doped barium zirconate polycrystal, with a total conductivity of 0.01 S cm^?1 at 396 °C for 200 h is demonstrated. Heavy doping of Sc in barium zirconate simultaneously enhances the proton concentration, bulk proton diffusivity, specific grain boundary conductivity, and grain growth. An accelerated stability test under a highly concentrated and humidified CO₂ stream using in situ X‐ray diffraction shows that the perovskite phase is stable over 240 h at 400 °C under 0.98 atm of CO₂. These results show great promises as an electrolyte in solid‐state electrochemical devices operated at intermediate temperatures.     

Stable Seamless Interfaces and Rapid Ionic Conductivity of Ca–CeO2/LiTFSI/PEO Composite Electrolyte for High‐Rate and High‐Voltage All‐Solid‐State Battery

Stable and seamless interfaces among solid components in all‐solid‐state batteries (ASSBs) are crucial for high ionic conductivity and high rate performance. This can be achieved by the combination of functional inorganic material and flexible polymer solid electrolyte. In this work, a flexible all‐solid‐state composite electrolyte is synthesized based on oxygen‐vacancy‐rich Ca‐doped CeO₂ (Ca–CeO₂) nanotube, lithium bis(trifluoromethanesulfonyl)imide (LiTFSI), and poly(ethylene oxide) (PEO), namely Ca–CeO₂/LiTFSI/PEO. Ca–CeO₂ nanotubes play a key role in enhancing the ionic conductivity and mechanical strength while the PEO offers flexibility and assures the stable seamless contact between the solid electrolyte and the electrodes in ASSBs. The as‐prepared electrolyte exhibits high ionic conductivity of 1.3 × 10^?4 S cm^?1 at 60 °C, a high lithium ion transference number of 0.453, and high‐voltage stability. More importantly, various electrochemical characterizations and density functional theory (DFT) calculations reveal that Ca–CeO₂ helps dissociate LiTFSI, produce free Li ions, and therefore enhance ionic conductivity. The ASSBs based on the as‐prepared Ca–CeO₂/LiTFSI/PEO composite electrolyte deliver high‐rate capability and high‐voltage stability.     

Low‐Cost Hollow Mesoporous Polymer Spheres and All‐Solid‐State Lithium,Sodium Batteries

A practical, low‐cost synthesis of hollow mesoporous organic polymer (HMOP) spheres is reported. The electrochemical properties of Li⁺/Na⁺‐electrolyte membranes with these spheres substituting for oxide filler particles in poly(ethylene oxide) (PEO)‐filler composite are explored. The electrolyte membranes are mechanically robust, thermally stable to over 250 °C, and block dendrites from a metallic‐lithium/sodium anode. The Li⁺/Na⁺ transfer impedance across the lithium/sodium–electrolyte interface is initially acceptable at 65 °C and scavenging of impurities by the porous‐spheres filler lowers this impedance relative to that with Al₂O₃. All‐solid‐state Li/LiFePO₄ and Na/NaTi₂(PO4)₃ cells give stable discharge capacity of ≈130 and 80 mAh g^?1, respectively, at 0.5 C and 65 °C for 100 cycles.     

Ultrathin,Flexible Polymer Electrolyte for Cost‐Effective Fabrication of All‐Solid‐State Lithium Metal Batteries

All‐solid‐state batteries are promising candidates for the next‐generation safer batteries. However, a number of obstacles have limited the practical application of all‐solid‐state Li batteries (ASSLBs), such as moderate ionic conductivity at room temperature. Here, unlike most of the previous approaches, superior performances of ASSLBs are achieved by greatly reducing the thickness of the solid‐state electrolyte (SSE), where ionic conductivity is no longer a limiting factor. The ultrathin SSE (7.5 µm) is developed by integrating the low‐cost polyethylene separator with polyethylene oxide (PEO)/Li‐salt (PPL). The ultrathin PPL shortens Li⁺ diffusion time and distance within the electrolyte, and provides sufficient Li⁺ conductance for batteries to operate at room temperature. The robust yet flexible polyethylene offers mechanical support for the soft PEO/Li‐salt, effectively preventing short‐circuits even under mechanical deformation. Various ASSLBs with PPL electrolyte show superior electrochemical performance. An initial capacity of 135 mAh g^?1 at room temperature and the high‐rate capacity up to 10 C at 60 °C can be achieved in LiFePO₄/PPL/Li batteries. The high‐energy‐density sulfur cathode and MoS₂ anode employing PPL electrolyte also realize remarkable performance. Moreover, the ASSLB can be assembled by a facile process, which can be easily scaled up to mass production.     

High‐Performance All‐Solid‐State Lithium–Sulfur Batteries Enabled by Amorphous Sulfur‐Coated Reduced Graphene Oxide Cathodes

Safety and the polysulfide shuttle reaction are two major challenges for liquid electrolyte lithium–sulfur (Li–S) batteries. Although use of solid‐state electrolytes can overcome these two challenges, it also brings new challenges by increasing the interface resistance and stress/strain. In this work, the interface resistance and stress/strain of sulfur cathodes are significantly reduced by conformal coating ≈2 nm sulfur (S) onto reduced graphene oxide (rGO). An Li–S full cell consisting of an rGO@S‐Li₁₀GeP₂S₁₂‐acetylene black (AB) composite cathode is evaluated. At 60 °C, the all‐solid‐state Li–S cell demonstrates a similar electrochemical performance as in liquid organic electrolyte, with high rate capacities of 1525.6, 1384.5, 1336.3, 903.2, 502.6, and 204.7 mA h g^?1 at 0.05, 0.1, 0.5, 1.0, 2.0, and 5.0 C, respectively. It can maintain a high and reversible capacity of 830 mA h g^?1 at 1.0 C for 750 cycles. The uniform distribution of the rGO@S nanocomposite in the Li₁₀GeP₂S₁₂‐AB matrix generates uniform volume changes during lithiation/delithiation, significantly reducing the stress/strain, thus extending the cycle life. Minimization of the stress/strain of solid cells is the key for a long cycle life of all‐solid‐state Li–S batteries.     

A Lithium Amide‐Borohydride Solid‐State Electrolyte with Lithium‐Ion Conductivities Comparable to Liquid Electrolytes

High ionic conductivity of up to 6.4 × 10^?3 S cm^?1 near room temperature (40 °C) in lithium amide‐borohydrides is reported, comparable to values of liquid organic electrolytes commonly employed in lithium‐ion batteries. Density functional theory is applied coupled with X‐ray diffraction, calorimetry, and nuclear magnetic resonance experiments to shed light on the conduction mechanism. A Li₄Ti₅O₁₂ half‐cell battery incorporating the lithium amide‐borohydride electrolyte exhibits good rate performance up to 3.5 mA cm^?2 (5 C) and stable cycling over 400 cycles at 1 C at 40 °C, indicating high bulk and interfacial stability. The results demonstrate the potential of lithium amide‐borohydrides as solid‐state electrolytes for high‐power lithium‐ion batteries.     

The size effect to O2−–Ce4+ charge transfer emission and band gap structure of Sr2CeO4

Sr₂CeO₄ phosphors with different crystalline sizes were synthesized by the sol–gel method or the solid‐state reaction. Their crystalline size, luminescence intensity of O^2??Ce⁴⁺ charge transfer and energy gaps were obtained through the characterization by X‐ray diffraction, photoluminescence spectra, as well as UV–visible diffuse reflectance measurements. An inverse relationship between photoluminescence (PL) spectra and crystalline size was observed when the heating temperature was from 1000°C to 1300°C. In addition, band energy calculated for all samples showed that a reaction temperature of 1200°C for the solid‐state method and 1100°C for sol–gel method gave the largest values, which corresponded with the smallest crystalline size. Correlation between PL intensity and crystalline size showed an inverse relationship. Band structure, density of states and partial density of states of the crystal were calculated to analyze the mechanism using the cambrige sequential total energy package (CASTEP) module integrated with Materials Studio software.     

Effect of cooling rate on the microstructure and luminescence properties of Sr2MgSi2O7:Eu2+,Dy3+ materials

Sr₂MgSi₂O₇:Eu²⁺,Dy³⁺ long afterglow materials were prepared by a high‐temperature solid‐state reaction method with different cooling rates. The cooling rate had a slight effect on X‐ray diffraction patterns and photoluminescence performance, but significantly modified the grain boundaries and long afterglow properties of the Sr₂MgSi₂O₇:Eu²⁺,Dy³⁺ materials. When the cooling rate was 1°C/min, grains remained intact with clear grain boundaries. As the cooling rate increased from 1°C/min to 5°C/min, some grain boundaries became indistinguishable. The afterglow properties were optimized, presenting best performance at the cooling rate of 3°C/min. The trap state was investigated and illustrated through thermoluminescence curves. The depths of the traps of all the samples were unchanged, whereas densities changed to a large extent, leading to different afterglow properties. The retrapping process is discussed based on the afterglow curves.     

A Flexible Solid Electrolyte with Multilayer Structure for Sodium Metal Batteries

Solid electrolytes (SEs) can potentially address the inherent safety problems of conventional organic liquid electrolytes. However, their low ionic conductivity and large interfacial resistance limit the practical applications of SEs. Here, a flexible solid electrolyte with a multilayer structure is fabricated by the UV curing of an interpenetrating network of poly(ether‐acrylate) (ipn‐PEA) in the Na₃Zr₂Si₂PO₁₂/poly(vinylidene fluoride‐hexafluoropropylene) porous skeleton (NZSP/PVDF‐HFP), exhibiting a high Na⁺ transference number of 0.63 and a suitable ionic conductivity of above 10^?4 S cm^?1 at 60 °C. In addition, due to the unique structure of the internal rigidity and external flexibility, the composite solid electrolyte can effectively mitigate interfacial ion transfer issues while guaranteeing a certain mechanical strength, and largely inhibiting the formation of dendrite and dead sodium. The solid sodium metal batteries using Na₃V₂(PO₄)₃ (NVP) as a cathode possess a discharge capacity of 85 mA h g^?1 after 100 cycles at 0.5 C, and achieve above 90% of capacity retention rate during 100 cycles at 0.1 C for Na_2/3Ni_1/3Mn_1/3Ti_1/3O₂ (NTMO) at 60 °C. The flexible solid electrolyte with multilayer structure shows a great advantage for managing the ionic conductivity and interface resistance problem, suggesting a promise as a practical sodium metal battery.     

Luminescence of the near‐ultraviolet blue‐emitting Ba9Al2Si6O24:Ce3+ phosphor

A near‐ultraviolet (NUV) blue‐emitting phosphor Ba₉Al₂Si₆O₂₄:Ce³⁺ (BAS:Ce³⁺) was synthesized using a high‐temperature solid‐state reaction. BAS:Ce³⁺ had an excitation band peak at about 328 nm and showed a blue emission band. The NUV‐blue emission band had a peak at about 386 nm with a band width of about 60 nm, attributed to the 5d–4f transition of Ce³⁺. Fluorescent decay showed an exponential model with a lifetime of 27.2 nsec. At 150°C, the luminescence intensity decreased to 68.7% compared with the intensity at room temperature.     

Rational Design of Hierarchical “Ceramic‐in‐Polymer” and “Polymer‐in‐Ceramic” Electrolytes for Dendrite‐Free Solid‐State Batteries

Solid polymer electrolytes as one of the promising solid‐state electrolytes have received extensive attention due to their excellent flexibility. However, the issues of lithium (Li) dendrite growth still hinder their practical applications in solid‐state batteries (SSBs). Herein, composite electrolytes from “ceramic‐in‐polymer” (CIP) to “polymer‐in‐ceramic” (PIC) with different sizes of garnet particles are investigated for their effectiveness in dendrite suppression. While the CIP electrolyte with 20 vol% 200 nm Li_6.4La₃Zr_1.4Ta_0.6O₁₂ (LLZTO) particles (CIP‐200 nm) exhibits the highest ionic conductivity of 1.6 × 10^?4 S cm^?1 at 30 °C and excellent flexibility, the PIC electrolyte with 80 vol% 5 µm LLZTO (PIC‐5 µm) shows the highest tensile strength of 12.7 MPa. A sandwich‐type composite electrolyte (SCE) with hierarchical garnet particles (a PIC‐5 µm interlayer sandwiched between two CIP‐200 nm thin layers) is constructed to simultaneously achieve dendrite suppression and excellent interfacial contact with Li metal. The SCE enables highly stable Li plating/stripping cycling for over 400 h at 0.2 mA cm^?2 at 30 °C. The LiFePO₄/SCE/Li cells also demonstrate excellent cycle performance at room temperature. Fabricating sandwich‐type composite electrolytes with hierarchical filler designs can be an effective strategy to achieve dendrite‐free SSBs with high performance and high safety at room temperature.     

Characterization of CaMKIIα holoenzyme stability

Ca²⁺/calmodulin‐dependent protein kinase II (CaMKII) is a Ser/Thr kinase necessary for long‐term memory formation and other Ca²⁺‐dependent signaling cascades such as fertilization. Here, we investigated the stability of CaMKIIα using a combination of differential scanning calorimetry (DSC), X‐ray crystallography, and mass photometry (MP). The kinase domain has a low thermal stability (apparent T_m = 36°C), which is slightly stabilized by ATP/MgCl₂ binding (apparent T_m = 40°C) and significantly stabilized by regulatory segment binding (apparent T_m = 60°C). We crystallized the kinase domain of CaMKII bound to p‐coumaric acid in the active site. This structure reveals solvent‐exposed hydrophobic residues in the substrate‐binding pocket, which are normally buried in the autoinhibited structure when the regulatory segment is present. This likely accounts for the large stabilization that we observe in DSC measurements comparing the kinase alone with the kinase plus regulatory segment. The hub domain alone is extremely stable (apparent T_m ~ 90°C), and the holoenzyme structure has multiple unfolding transitions ranging from ~60°C to 100°C. Using MP, we compared a CaMKIIα holoenzyme with different variable linker regions and determined that the dissociation of both these holoenzymes occurs at a higher concentration (is less stable) compared with the hub domain alone. We conclude that within the context of the holoenzyme structure, the kinase domain is stabilized, whereas the hub domain is destabilized. These data support a model where domains within the holoenzyme interact.     

Effect of CaCN2 on the preparation of CaAlSiN3:Eu2+ phosphors

Highly efficient red‐emitting phosphors, CaAlSiN₃:Eu²⁺, were successfully prepared by the solid‐state method using calcium cyanide (CaCN₂) as the single calcium source. The influences of crystallization temperature, crystallization time, calcination mode and compounds ratio on the photoluminescent properties were investigated. The CaAlSiN₃:Eu²⁺ phosphors were obtained with 1 mol% CaCN₂ by a two‐step calcination procedure at 900°C for 2 h and subsequently at 1600°C for 8 h. The CaAlSiN₃:Eu²⁺ phosphors showed the strongest luminescent intensity at 660 nm when excited by 468 nm. With an increase in crystallization time, the maximum wavelength of the emission was shifted from 644 nm to 660 nm.     

Ultra‐stable phosphoglucose isomerase through immobilization of cellulose‐binding module‐tagged thermophilic enzyme on low‐cost high‐capacity cellulosic adsorbent

One‐step enzyme purification and immobilization were developed based on simple adsorption of a family 3 cellulose‐binding module (CBM)‐tagged protein on the external surface of high‐capacity regenerated amorphous cellulose (RAC). An open reading frame (ORF) Cthe0217 encoding a putative phosphoglucose isomerase (PGI, EC 5.3.1.9) from a thermophilic bacterium Clostridium thermocellum was cloned and the recombinant proteins with or without CBM were over‐expressed in Escherichia coli. The rate constant (k_cat) and Michaelis–Menten constant (K_m) of CBM‐free PGI at 60°C were 2,765 s^?1 and 2.89 mM, respectively. PGI was stable at a high protein concentration of 0.1 g/L but deactivated rapidly at low concentrations. Immobilized CBM (iCBM)‐PGI on RAC was extremely stable at ～60°C, nearly independent of its mass concentration in bulk solution, because its local concentration on the solid support was constant. iCBM‐PGI at a low concentration of 0.001 g/L had a half‐life time of 190 h, approximately 80‐fold of that of free PGI. Total turn‐over number of iCBM‐PGI was as high as 1.1 × 10⁹ mole of product per mole of enzyme at 60°C. These results suggest that a combination of low‐cost enzyme immobilization and thermoenzyme led to an ultra‐stable enzyme building block suitable for cell‐free synthetic pathway biotransformation that can implement complicated biochemical reactions in vitro. © 2011 American Institute of Chemical Engineers Biotechnol. Prog., 2011.     

Physically Stable Polymer‐Membrane Electrolytes for Highly Efficient Solid‐State Dye‐Sensitized Solar Cells with Long‐Term Stability

A 3D polymer‐network‐membrane (3D‐PNM) electrolyte is described for highly stable, solid‐state dye‐sensitized solar cells (DSCs) with excellent power‐conversion efficiency (PCE). The 3D‐PNM electrolyte is prepared by using one‐pot in situ cross‐linking polymerization on the surface of dye‐sensitized TiO₂ particles in the presence of redox species. This method allows the direct connection of the 3D‐PNM to the surface of the TiO₂ particles as well as the in situ preparation of the electrolyte gel during device assembly. There are two junction areas (liquid and solid‐state junctions) in the DSCs that employ conventional polymer electrolytes, and the major interface is at the liquid‐state junction. The solid‐state junction is dominant in the DSCs that employ the 3D‐PNM electrolyte, which exhibit almost constant performance during aging at 65 °C for over 700 h (17.0 to 17.2 mA cm^–2). The best cell performance gives a PCE of 9.1%; this is slightly better than the performance of a DSC that employs a liquid electrolyte.     

Low‐Temperature Micro‐Solid Oxide Fuel Cells with Partially Amorphous La0.6Sr0.4CoO3‐δ Cathodes

Partially amorphous La_0.6Sr_0.4CoO_3‐δ (LSC) thin‐film cathodes are fabricated using pulsed laser deposition and are integrated in free‐standing micro‐solid oxide fuel cells (micro‐SOFC) with a 3YSZ electrolyte and a Pt anode. A low degree of crystallinity of the LSC layers is achieved by taking advantage of the miniaturization of the cells, which permits low‐temperature operation (300–450 °C). Thermomechanically stable micro‐SOFC are obtained with strongly buckled electrolyte membranes. The nanoporous columnar microstructure of the LSC layers provides a large surface area for oxygen incorporation and is also believed to reduce the amount of stress at the cathode/electrolyte interface. With a high rate of failure‐free micro‐SOFC membranes, it is possible to avoid gas cross‐over and open‐circuit voltages of 1.06 V are attained. First power densities as high as 200–262 mW cm^?2 at 400–450 °C are achieved. The area‐specific resistance of the oxygen reduction reaction is lower than 0.3 Ω cm² at 400 °C around the peak power density. These outstanding findings demonstrate that partially amorphous oxides are promising electrode candidates for the next‐generation of solid oxide fuel cells working at low‐temperatures.     

Protein stabilization with a dipeptide‐mimic triazine‐scaffolded synthetic affinity ligand

Protein stabilization was achieved by a novel approach based on the adsorption and establishment of affinity‐like interactions with a biomimetic triazine‐scaffolded ligand. A synthetic lead compound (ligand 3′/11, K_a ≈ 10⁴ M^?1) was selected from a previously screened solid‐phase library of affinity ligands for studies of adsorption and stabilization of cutinase from Fusarium solani pisi used as a model system. This ligand, directly synthesized in agarose by a well‐established solid‐phase synthesis method, was able to strongly bind cutinase and led to impressive half‐lives of more than 8 h at 70 °C, and of approximately 34 h at 60 °C for bound protein (a 25‐ and 57‐fold increase as compared with the free enzyme, respectively). The ligand density in the solid matrix was found to be a determinant parameter for cutinase stabilization. It is conceivable that the highly stabilizing effect observed results from the binding of more than one ligand residue to the enzyme, creating specific macromolecular configurations that lock structural mobility thus improving molecular stability. Copyright © 2013 John Wiley & Sons, Ltd.