Anomalous Charge‐Extraction Behavior for Graphene‐Oxide (GO) and Reduced Graphene‐Oxide (rGO) Films as Efficient p‐Contact Layers for High‐Performance Perovskite Solar Cells

Reduced graphene oxides (rGO) are synthesized via reduction of GO with reducing agents as a hole‐extraction layer for high‐performance inverted planar heterojunction perovskite solar cells. The best efficiencies of power conversion (PCE) of these rGO cells exceed 16%, much greater than those made of GO and poly(3,4‐ethenedioxythiophene):poly(styrenesulfonate) films. A flexible rGO device shows PCE 13.8% and maintains 70% of its initial performance over 150 bending cycles. It is found that the hole‐extraction period is much smaller for the GO/methylammonium lead‐iodide perovskite (PSK) film than for the other rGO/PSK films, which contradicts their device performances. Photoluminescence and transient photoelectric decays are measured and control experiments are performed to prove that the reduction of the oxygen‐containing groups in GO significantly decreases the ability of hole extraction from PSK to rGO and also retards the charge recombination at the rGO/PSK interface. When the hole injection from PSK to GO occurs rapidly, hole propagation from GO to the indium‐doped tin oxide (ITO) substrate becomes a bottleneck to overcome, which leads to a rapid charge recombination that decreases the performance of the GO device relative to the rGO device.     

Nanodiamond‐Embedded p‐Type Copper(I) Oxide Nanocrystals for Broad‐Spectrum Photocatalytic Hydrogen Evolution

Copper(I) oxide (Cu₂O) is an attractive photocatalyst because of its abundance, low toxicity, environmental compatibility, and narrow direct band gap, which allows efficient light harvesting. However, Cu₂O exhibits poor photocatalytic performance and photostability because of its short electron diffusion length and low hole mobility. Here, it is demonstrated that nanodiamond (ND) can greatly improve the photocatalytic hydrogen evolution reaction (HER) of the p‐type photocatalyst Cu₂O nanocrystals by nanocomposition. Compared with pure Cu₂O nanocrystals, this composite shows a tremendous improvement in HER performance and photostability. HER rates of 100.0 mg NDs‐Cu₂O nanocrystals are 1597 and 824 under the simulated solar light irradiation (AM 1.5, 100 mW cm^?2) and visible light irradiation (420–760 nm, 77.5 mW cm^?2), respectively. The solar‐to‐hydrogen conversion efficiency of this composite is 0.85%, which is nearly ten times higher than that of pure Cu₂O. The quantum efficiency of the composite is high, with values of 0.17% at and 0.23% at . The broad spectral response of ND provides numerous carriers for the subsequent reactions. The electron‐donating ability of ND and suitable band structures of the two components promote electron injection from ND to Cu₂O. These results suggest the broad applicability of ND to ameliorate the photoelectric properties of semiconductors.     

Electron‐Beam‐Evaporated Nickel Oxide Hole Transport Layers for Perovskite‐Based Photovoltaics

High‐quality charge carrier transport materials are of key importance for stable and efficient perovskite‐based photovoltaics. This work reports on electron‐beam‐evaporated nickel oxide (NiO_x) layers, resulting in stable power conversion efficiencies (PCEs) of up to 18.5% when integrated into solar cells employing inkjet‐printed perovskite absorbers. By adding oxygen as a process gas and optimizing the layer thickness, transparent and efficient NiO_x hole transport layers (HTLs) are fabricated, exhibiting an average absorptance of only 1%. The versatility of the material is demonstrated for different absorber compositions and deposition techniques. As another highlight of this work, all‐evaporated perovskite solar cells employing an inorganic NiO_x HTL are presented, achieving stable PCEs of up to 15.4%. Along with good PCEs, devices with electron‐beam‐evaporated NiO_x show improved stability under realistic operating conditions with negligible degradation after 40 h of maximum power point tracking at 75 °C. Additionally, a strong improvement in device stability under ultraviolet radiation is found if compared to conventional perovskite solar cell architectures employing other metal oxide charge transport layers (e.g., titanium dioxide). Finally, an all‐evaporated perovskite solar mini‐module with a NiO_x HTL is presented, reaching a PCE of 12.4% on an active device area of 2.3 cm².     

Understanding Performance Degradation in Cation‐Disordered Rock‐Salt Oxide Cathodes

The collective redox activities of transition‐metal (TM) cations and oxygen anions have been shown to increase charge storage capacity in both Li‐rich layered and cation‐disordered rock‐salt cathodes. Repeated cycling involving anionic redox is known to trigger TM migration and phase transformation in layered Li‐ and Mn‐rich (LMR) oxides, however, detailed mechanistic understanding on the recently discovered Li‐rich rock‐salt cathodes is largely missing. The present study systematically investigates the effect of oxygen redox on a Li_1.3Nb_0.3Mn_0.4O₂ cathode and demonstrates that performance deterioration is directly correlated to the extent of oxygen redox. It is shown that voltage fade and hysteresis begin only after initiating anionic redox at high voltages, which grows progressively with either deeper oxidation of oxygen at higher potential or extended cycling. In contrast to what is reported on layered LMR oxides, extensive TM reduction is observed but phase transition is not detected in the cycled oxide. A densification/degradation mechanism is proposed accordingly which elucidates how a unique combination of extensive chemical reduction of TM and reduced quality of the Li percolation network in cation‐disordered rock‐salts can lead to performance degradation in these newer cathodes with 3D Li migration pathways. Design strategies to achieve balanced capacity and stability are also discussed.     

Lithium‐ and Manganese‐Rich Oxide Cathode Materials for High‐Energy Lithium Ion Batteries

Layered lithium‐ and manganese‐rich oxides (LMROs), described as xLi₂MnO₃·(1–x)LiMO₂ or Li_1+yM_1–yO₂ (M = Mn, Ni, Co, etc., 0 < x <1, 0 < y ≤ 0.33), have attracted much attention as cathode materials for lithium ion batteries in recent years. They exhibit very promising capacities, up to above 300 mA h g^?1, due to transition metal redox reactions and unconventional oxygen anion redox reaction. However, they suffer from structural degradation and severe voltage fade (i.e., decreasing energy storage) upon cycling, which are plaguing their practical application. Thus, this review will aim to describe the pristine structure, high‐capacity mechanisms and structure evolutions of LMROs. Also, recent progress associated with understanding and mitigating the voltage decay of LMROs will be discussed. Several approaches to solve this problem, such as adjusting cycling voltage window and chemical composition, optimizing synthesis strategy, controlling morphology, doping, surface modification, constructing core‐shell and layered‐spinel hetero structures, are described in detail.     

Amorphous Tin‐Based Composite Oxide: A High‐Rate and Ultralong‐Life Sodium‐Ion‐Storage Material

Energy‐storage technology is moving beyond lithium batteries to sodium as a result of its high abundance and low cost. However, this sensible transition requires the discovery of high‐rate and long‐lifespan anode materials, which remains a significant challenge. Here, the facile synthesis of an amorphous Sn₂P₂O₇/reduced graphene oxide nanocomposite and its sodium storage performance between 0.01 and 3.0 V are reported for the first time. This hybrid electrode delivers a high specific capacity of 480 mA h g^?1 at a current density of 50 mA g^?1 and superior rate performance of 250 and 165 mA h g^?1 at 2 and 10 A g^?1, respectively. Strikingly, this anode can sustain 15 000 cycles while retaining over 70% of the initial capacity. Quantitative kinetic analysis reveals that the sodium storage is governed by pseudocapacitance, particularly at high current rates. A full cell with sodium super ionic conductor (NASICON)‐structured Na₃V₂(PO₄)₂F₃ and Na₃V₂(PO₄)₃ as cathodes exhibits a high energy density of over 140 W h kg^?1 and a power density of nearly 9000 W kg^?1 as well as stability over 1000 cycles. This exceptional performance suggests that the present system is a promising power source for promoting the substantial use of low‐cost energy storage systems.     

Ethylene Carbonate‐Free Electrolytes for High‐Nickel Layered Oxide Cathodes in Lithium‐Ion Batteries

Layered lithium nickel oxide (LiNiO₂) can provide very high energy density among intercalation cathode materials for lithium‐ion batteries, but suffers from poor cycle life and thermal‐abuse tolerance with large lithium utilization. In addition to stabilization of the active cathode material, a concurrent development of electrolyte systems of better compatibility is critical to overcome these limitations for practical applications. Here, with nonaqueous electrolytes based on exclusively aprotic acyclic carbonates free of ethylene carbonate (EC), superior electrochemical and thermal characteristics are obtained with an ultrahigh‐nickel cathode (LiNi_0.94Co_0.06O₂), capable of reaching a 235 mA h g^?1 specific capacity. Pouch‐type graphite|LiNi_0.94Co_0.06O₂ cells in EC‐free electrolytes withstand several hundred charge–discharge cycles with minor degradation at both ambient and elevated temperatures. In thermal‐abuse tests, the cathode at full charge, while reacting aggressively with EC‐based electrolytes below 200 °C, shows suppressed self‐heating without EC. Through 3D chemical and structural analyses, the intriguing impact of EC is visualized in aggravating unwanted surface parasitic reactions and irreversible bulk structural degradation of the cathode at high voltages. These results provide important insights in designing high‐energy electrodes for long‐lasting and reliable lithium‐ion batteries.     

A Layered–Tunnel Intergrowth Structure for High‐Performance Sodium‐Ion Oxide Cathode

Delivery of high‐energy density with long cycle life is facing a severe challenge in developing cathode materials for rechargeable sodium‐ion batteries (SIBs). Here a composite Na_0.6MnO₂ with layered–tunnel structure combining intergrowth morphology of nanoplates and nanorods for SIBs, which is clearly confirmed by micro scanning electron microscopy, high‐resolution transmission electron microscopy as well as scanning transmission electron microscopy with atomic resolution is presented. Owing to the integrated advantages of P2 layered structure with high capacity and that of the tunnel structure with excellent cycling stability and superior rate performance, the composite electrode delivers a reversible discharge capacity of 198.2 mAh g^?1 at 0.2C rate, leading to a high‐energy density of 520.4 Wh kg^?1. This intergrowth integration engineering strategy may modulate the physical and chemical properties in oxide cathodes and provide new perspectives on the optimal design of high‐energy density and high‐stable materials for SIBs.     

A Stable Layered Oxide Cathode Material for High‐Performance Sodium‐Ion Battery

As one of the most promising cathode candidates for room‐temperature sodium‐ion batteries (SIBs), P2‐type layered oxides face the challenge of simultaneously realizing high‐rate performance while achieving long cycle life. Here, a stable Na_2/3Ni_1/6Mn_2/3Cu_1/9Mg_1/18O₂ cathode material is proposed that consists of multiple‐layer oriented stacking nanoflakes, in which the nickel sites are partially substituted by copper and magnesium, a characteristic of the material that is confirmed by multiscale scanning transmission electron microscopy and electron energy loss spectroscopy techniques. Owing to the optimal morphology structure modulation and chemical element substitution strategy, the electrode displays remarkable rate performance (73% capacity retention at 30C compared to 0.5C) and outstanding cycling stability in Na half‐cell system couple with unprecedented full battery performance. The underlying thermal stability, phase stability, and Na⁺ storage mechanisms are clearly elucidated through the systematical characterizations of electrochemical behaviors, in situ X‐ray diffraction at different temperatures, and operando X‐ray diffraction upon Na⁺ deintercalation/intercalation. Surprisingly, a quasi‐solid‐solution reaction is switched to an absolute solid‐solution reaction and a capacitive Na⁺ storage mechanism is demonstrated via quantitative electrochemical kinetics calculation during charge/discharge process. Such a simple and effective strategy might reveal a new avenue into the rational design of excellent rate capability and long cycle stability cathode materials for practical SIBs.     

Nickel‐Rich and Lithium‐Rich Layered Oxide Cathodes: Progress and Perspectives

Ni‐rich layered oxides and Li‐rich layered oxides are topics of much research interest as cathodes for Li‐ion batteries due to their low cost and higher discharge capacities compared to those of LiCoO₂ and LiMn₂O₄. However, Ni‐rich layered oxides have several pitfalls, including difficulty in synthesizing a well‐ordered material with all Ni³⁺ ions, poor cyclability, moisture sensitivity, a thermal runaway reaction, and formation of a harmful surface layer caused by side reactions with the electrolyte. Recent efforts towards Ni‐rich layered oxides have centered on optimizing the composition and processing conditions to obtain controlled bulk and surface compositions to overcome the capacity fade. Li‐rich layered oxides also have negative aspects, including oxygen loss from the lattice during first charge, a large first cycle irreversible capacity loss, poor rate capability, side reactions with the electrolyte, low tap density, and voltage decay during extended cycling. Recent work on Li‐rich layered oxides has focused on understanding the surface and bulk structures and eliminating the undesirable properties. Followed by a brief introduction, an account of recent developments on the understanding and performance gains of Ni‐rich and Li‐rich layered oxide cathodes is provided, along with future research directions.     

High‐Performance All‐Solid‐State Lithium–Sulfur Batteries Enabled by Amorphous Sulfur‐Coated Reduced Graphene Oxide Cathodes

Safety and the polysulfide shuttle reaction are two major challenges for liquid electrolyte lithium–sulfur (Li–S) batteries. Although use of solid‐state electrolytes can overcome these two challenges, it also brings new challenges by increasing the interface resistance and stress/strain. In this work, the interface resistance and stress/strain of sulfur cathodes are significantly reduced by conformal coating ≈2 nm sulfur (S) onto reduced graphene oxide (rGO). An Li–S full cell consisting of an rGO@S‐Li₁₀GeP₂S₁₂‐acetylene black (AB) composite cathode is evaluated. At 60 °C, the all‐solid‐state Li–S cell demonstrates a similar electrochemical performance as in liquid organic electrolyte, with high rate capacities of 1525.6, 1384.5, 1336.3, 903.2, 502.6, and 204.7 mA h g^?1 at 0.05, 0.1, 0.5, 1.0, 2.0, and 5.0 C, respectively. It can maintain a high and reversible capacity of 830 mA h g^?1 at 1.0 C for 750 cycles. The uniform distribution of the rGO@S nanocomposite in the Li₁₀GeP₂S₁₂‐AB matrix generates uniform volume changes during lithiation/delithiation, significantly reducing the stress/strain, thus extending the cycle life. Minimization of the stress/strain of solid cells is the key for a long cycle life of all‐solid‐state Li–S batteries.     

Resolution of 1‐n‐Butyl‐3‐Methyl‐3‐Phospholene 1‐Oxide With TADDOL Derivatives and Calcium Salts of O,O'‐Dibenzoyl‐(2R,3R)‐ or O,O'‐di‐p‐Toluoyl‐(2R,3R)‐tartaric Acid

The resolution methods applying (?)‐(4R,5R)‐4,5‐bis(diphenylhydroxymethyl)‐2,2‐dimethyldioxolane (“TADDOL”), (?)‐(2R,3R)‐α,α,α',α'‐tetraphenyl‐1,4‐dioxaspiro[4.5]decan‐2,3‐dimethanol (“spiro‐TADDOL”), as well as the acidic and neutral Ca²⁺ salts of (?)‐O,O'‐dibenzoyl‐ and (?)‐O,O'‐di‐p‐toluoyl‐(2R,3R)‐tartaric acid were extended for the preparation of 1‐n‐butyl‐3‐methyl‐3‐phospholene 1‐oxide in optically active form. In one case, the intermediate diastereomeric complex could be identified by single‐crystal X‐ray analysis. The absolute P‐configuration of the enantiomers of the phospholene oxide was also determined by comparing the experimentally obtained and calculated CD spectra. Chirality 26:174–182, 2014. © 2014 Wiley Periodicals, Inc.     

Sodium Ion Stabilized Vanadium Oxide Nanowire Cathode for High‐Performance Zinc‐Ion Batteries

Aqueous Zn‐ion batteries (ZIBs) have received incremental attention because of their cost‐effectiveness and the materials abundance. They are a promising choice for large‐scale energy storage applications. However, developing suitable cathode materials for ZIBs remains a great challenge. In this work, pioneering work on the designing and construction of aqueous Zn//Na_0.33V₂O₅ batteries is reported. The Na_0.33V₂O₅ (NVO) electrode delivers a high capacity of 367.1 mA h g^?1 at 0.1 A g^?1, and exhibits long‐term cyclic stability with a capacity retention over 93% for 1000 cycles. The improvement of electrical conductivity, resulting from the intercalation of sodium ions between the [V₄O₁₂]_n layers, is demonstrated by single nanowire device. Furthermore, the reversible intercalation reaction mechanism is confirmed by X‐ray diffraction, Raman, X‐ray photoelectron spectroscopy, scanning electron microscopy, and transmission electron microscopy analysis. The outstanding performance can be attributed to the stable layered structure and high conductivity of NVO. This work also indicates that layered structural materials show great potential as the cathode of ZIBs, and the indigenous ions can act as pillars to stabilize the layered structure, thereby ensuring an enhanced cycling stability.     

Stabilized Co‐Free Li‐Rich Oxide Cathode Particles with An Artificial Surface Prereconstruction

Li‐rich metal oxide (LXMO) cathodes have attracted intense interest for rechargeable batteries because of their high capacity above 250 mAh g^?1. However, the side effects of hybrid anion and cation redox (HACR) reactions, such as oxygen release and phase collapse that result from global oxygen migration (GOM), have prohibited the commercialization of LXMO. GOM not only destabilizes the oxygen sublattice in cycling, aggravating the well‐known voltage fading, but also intensifies electrolyte decomposition and Mn dissolution, causing severe full‐cell performance degradation. Herein, an artificial surface prereconstruction (ASR) for Li_1.2Mn_0.6Ni_0.2O₂ particles with a molten‐molybdate leaching is conducted, which creates a crystal‐dense anion‐redox‐free LiMn_1.5Ni_0.5O₄ shell that completely encloses the LXMO lattice (ASR‐LXMO). Differential electrochemical mass spectroscopy and soft X‐ray absorption spectroscopy analyses demonstrate that GOM is shut down in cycling, which not only stabilizes HACR in ASR‐LXMO, but also mitigates the electrolyte decomposition and Mn dissolution. ASR‐LXMO displays greatly stabilized cycling performance as it retains 237.4 mAh g^?1 with an average discharge voltage of 3.30 V after 200 cycles. More crucially, while the pristine LXMO cycling cannot survive 90 cycles in a pouch full‐cell matched with a commercial graphite anode and lean (2 g A^?1 h^?1) electrolyte, ASR‐LXMO shows high capacity retention of 76% after 125 cycles in full‐cell cycling.     

Three‐Dimensional Nanostructured Indium‐Tin‐Oxide Electrodes for Enhanced Performance of Bulk Heterojunction Organic Solar Cells

A three‐dimensional indium tin oxide (ITO) nanohelix (NH) array is presented as a multifunctional electrode for bulk heterojunction organic solar cells for simultaneously improving light absorption and charge transport from the active region to the anode. It is shown that the ITO NH array, which is easily fabricated using an oblique‐angle‐deposition technique, acts as an effective antireflection coating as well as a light‐scattering layer, resulting in much enhanced light harvesting. Furthermore, the larger interfacial area between the electrode and the active layer, together with the enhanced carrier mobility through highly conductive ITO NH facilitate transport and collection of charge carriers. The optical and electrical improvements enabled by the ITO NH electrode result in a 10% increase in short‐circuit current density and power‐conversion efficiency of the solar cells.     

Nanowire‐Based Three‐Dimensional Transparent Conducting Oxide Electrodes for Extremely Fast Charge Collection

A 3D transparent conducting oxide (3D‐TCO) has been fabricated by growing Sn‐doped indium oxide (ITO) nanowire arrays on glass substrates via a vapor transport method. The 3D TCO charge‐collection properties have been compared to those of conventional two‐dimensional TCO (2D‐TCO) thin films. For use as a photoelectrode in dye‐sensitized solar cells, ITO‐TiO₂ core‐shell nanowire arrays were prepared by depositing a 45 nm‐thick mesoporous TiO₂ shell layer consisting of ～6 nm anatase nanoparticles using TiCl₄ treatments. Dye‐sensitized solar cells fabricated using these ITO‐TiO₂ core‐shell nanowire arrays show extremely fast charge collection owing to the shorter electron paths across the 45 nm‐thick TiO₂ shell compared to the 2D TCO. Interestingly, the charge‐collection time does not increase with the overall electrode thickness, which is counterintuitive to conventional diffusion models. This result implies that, in principle, maximum light harvesting can be achieved without hindering the charge collection. The proposed new 3D TCO should also be attractive for other photovoltaic applications where the active layer thickness is limited by poor charge collection.