Variation of cellulose microfibril angles in softwoods and hardwoods-a possible strategy of mechanical optimization

Position-resolved small-angle X-ray scattering was used to investigate the nanostructure of the wood cell wall in two softwood species (Norwegian spruce and Scots pine) and two hardwood species (pedunculate oak and copper beech). The tilt angle of the cellulose fibrils in the wood cell wall versus the longitudinal cell axis (microfibril angle) was systematically studied over a wide range of annual rings in each tree. The measured angles were correlated with the distance from the pith and the results were compared. The microfibril angle was found to decrease from pith to bark in all four trees, but was generally higher in the softwood than in the hardwood. In Norwegian spruce, the microfibril angles were higher in late wood than in early wood; in Scots pine the opposite was observed. In pedunculate oak and copper beech, low angles were found in the major part of the stem, except for the very first annual rings in pedunculate oak. The results are interpreted in terms of mechanical optimization. An attempt was made to give a quantitative estimation for the mechanical constraints imposed on a tree of given dimensions and to establish a model that could explain the general decrease of microfibril angles from pith to bark.     

Enzyme-inducing and cytotoxic effects of wood-based materials used as bedding for laboratory animals. Comparison by a cell culture study

Enzyme-inducing and cytotoxic effects of wood-based materials used as bedding for laboratory animals were studied in a cell culture system. Mouse hepatoma cell line, Hepa-1, was exposed to acetone extracts of hardwoods (alder and aspen), softwoods (pine and a mixture of pine and spruce) and cellulose materials. Cytotoxicity and induction of cytochrome P450IA1 (aryl hydrocarbon hydroxylase) and aldehyde dehydrogenase were measured. Both softwood and hardwood extracts were shown to contain inducers of these enzymes. Pine appeared to be the most potent inducer and softwoods more potent than hardwoods. The softwoods and alder were clearly more cytotoxic than aspen. The two bleached cellulose materials were found to contain inducers of aryl hydrocarbon hydroxylase. Unlike the wood beddings, the extracts of the cellulose materials were not found to be toxic to the cells. Hepa-1 cell culture system was found to be a rapid and sensitive method for screening and comparative purposes.     

Decay and termite resistance of medium density fiberboard (MDF) made from different wood species

Medium density fiberboard (MDF) production worldwide is increasing due to the development of new manufacturing technologies. As a result, MDF products are increasingly utilized in traditional wood applications that require fungal and insect resistance. This study evaluated the ability of white and brown rot fungi and termites to decompose MDF consisting of different wood species by measuring weight loss. Furnish in the boards was prepared from heart and sapwood portions of pine (Pinus nigra Arnold var. pallasiana), beech (Fagus orientalis Lipsky), and European oak (Quercus robur L.) species. Fungal decay resistance tests were performed according to ASTM D 2017-81 standard method using two brown-rot fungi, Gloeophyllum trabeum (Pers. ex Fr.) Murr. (Mad 617), Postia placenta (Fries) M. Larsen et Lombard (Mad 698), and one white-rot fungus, Trametes versicolor (L. ex Ft.) Pilat (Mad 697). MDF and wood specimens were also bioassayed against the eastern subterranean termite, Reticulitermes flavipes (Kollar) in order to determine termite resistance of the specimens. MDF specimens containing oak and mixed furnish demonstrated increased durability against decay fungi. Only pine, oak, and mixed MDF specimens met the 25% or less weight loss limit to be classified resistant according to ASTM D 2017-81 standard method. Overall, MDF specimens made from oak showed better performance than oak solid wood specimens. Accelerated aging according to ASTM D 1037-96a standard method before fungal bioassay decreased fungal resistance of the specimens. In contrast to the fungal bioassay, MDF specimens made from beech and mixed furnish showed decreased weight losses from termite attack after 4 weeks. However, none of the MDF specimens were resistant to termite attack. In severe conditions, the MDFs may require the incorporation of chemical biocides prior to board production for increasing the resistance of MDF to termite attack.     

Performance of oak,beech and spruce beams after more than 100 years in service

The aim of this study was to investigate differences in the mechanical and fungicidal properties of three different wood species (English oak (Quercus sp.), common beech (Fagus sylvatica) and Norway spruce (Picea abies)) that had been in indoor use for several decades, compared to control specimens of freshly cut timber. The collected material was cut into smaller samples prior to further analysis. Extractive content, mechanical, fungicidal and sorption properties were determined according to standard procedures. The obtained results showed that the mechanical properties of oak wood do not deteriorate over the investigated time frame. On the other hand, the resistance of oak wood against fungi decreases over time. The reason for this is yet to be confirmed; it may be due to degradation of secondary metabolites. Similar results have been reported for spruce wood. There were no statistically significant differences in the mechanical properties of old and new spruce wood. In contrast to oak wood, there were also no significant differences in fungicidal properties, bearing in mind that spruce wood has lower durability than oak wood. Aging of beech wood resulted in a considerable decrease in the tested mechanical properties but showed no significant differences in fungicidal properties. Old beech wood specimens were moderately deteriorated by insects and fungi, which was the reason for the loss of bending and compressive strength. Our results confirm that most of the relevant properties do not deteriorate with time and that wood can be reused for a variety of other applications even after decades in service.     

Vibrational spectroscopy and X-ray diffraction methods to establish the differences between hardwood and softwood

FT-IR spectrometry and X-ray diffraction were applied to probe the differences between pulp fibers from Eucalyptus wood (hardwood) and Norway spruce wood (softwood). Wood processing was found to induce certain structural alterations within its components depending on the type of wood and the applied procedure. These differences were established by using techniques such as; spectral comparison of wood samples with those of individual component fractions, derivative spectroscopy, bands deconvolution, etc. FT-IR spectroscopy was shown to be an important tool that provided details about the structural characteristics of hardwood and softwood samples. Using second-derivative spectra and deconvolution processes small differences between spectra became apparent that allowed correlations to be made related to wood composition. In addition a correlation was established between the integral absorptions for the various bands and lignin content as well as the lignin/carbohydrate content. Relations between various spectral characteristics and the degree of crystallinity and sample composition were established.     

Ultrastructural changes during wood decay by Antrodiella sp. RK1

Southern yellow pine (softwood) and maple (hardwood) wood decayed for 12 weeks by Antrodiella sp. RK1 had average weight losses of 20 and 19%, respectively, and approximately 34 to 35% lignin loss. The ratio of percentage lignin loss to glucose loss was 3.6 and 2.7 for softwood and hardwood, respectively. There was negligible loss of other wood sugars such as xylose, arabinose, galactose and mannose. Scanning electron microscopy revealed the presence of erosion troughs and bore holes in decayed samples of both softwood and hardwood. Secondary walls were void of lignin, middle lamella and cell corners were extensively decayed. Ca²⁺ crystals were abundantly present in the areas of decay. Transmission electron micrographs revealed the presence of hyphal sheath and growth of hyphae directly through the cell corners.R.N. Patel and K.K. Rao are with the Department of Microbiology & Biotechnology Center, Faculty of Science, M.S. University of Baroda, Baroda-390 002, India.     

Enzymatic hydrolysis of biomass from wood

Current research and development in cellulosic ethanol production has been focused mainly on agricultural residues and dedicated energy crops such as corn stover and switchgrass; however, woody biomass remains a very important feedstock for ethanol production. The precise composition of hemicellulose in the wood is strongly dependent on the plant species, therefore different types of enzymes are needed based on hemicellulose complexity and type of pretreatment. In general, hardwood species have much lower recalcitrance to enzymes than softwood. For hardwood, xylanases, beta‐xylosidases and xyloglucanases are the main hemicellulases involved in degradation of the hemicellulose backbone, while for softwood the effect of mannanases and beta‐mannosidases is more relevant. Furthermore, there are different key accessory enzymes involved in removing the hemicellulosic fraction and increasing accessibility of cellulases to the cellulose fibres improving the hydrolysis process. A diversity of enzymatic cocktails has been tested using from low to high densities of biomass (2–20% total solids) and a broad range of results has been obtained. The performance of recently developed commercial cocktails on hardwoods and softwoods will enable a further step for the commercialization of fuel ethanol from wood.     

Comparative durability of untreated wood in use above ground

Cross-brace units constructed of 10 different softwoods and nine different hardwoods were exposed on a test fence in Wisconsin for up to 22 years. Sapwood was included for all species and heartwood for some. The objective of this study was to determine the above-ground longevity of these woods against decay. The wood was classified into above-ground decay resistance groups. The longevity spans apply only to structural components similar in cross-sectional size to the test units used in this study. Millwork and fencing components may fit into this category. Woods estimated to last more than 20 years above ground, and thus classified as most resistant, included the heartwood of Douglas-fir, western white pine, redwood, Eucalyptus sp., red and white oak, lodgepole pine, ponderosa pine, western red cedar, and the sapwood of redwood, white oak, and red oak. No woods fell into the nonresistant class ( 7 years expected average life). The remaining woods were classified moderately resistant or resistant based upon service lives of 8 to 13 and 14 to 19 years, respectively.     

The relationship between wood litter infall and relative abundance and feeding activity of subterranean termites Reticulitermes spp. in three southeastern coastal plain habitats

We estimated the densities of termites in dead wood using a point-quarter technique in four habitats: pine plantations subject to control burning and unburned, lowland hardwood forest, and turkey oak woodland. The burned pine plantation had the highest estimated termite density, 13×10⁶·ha^-1 unburned pine plantation and lowland hardwood had estimated densities of 2.6×10⁶·ha^-1 and 2.2×10⁶·ha^-1, respectively, and the turkey oak woodland had an estimated densities of 61.9×10³·ha^-1. There were varying percentages of Reticulitermes flavipes and R. virginicus in the various habitats. There was nearly linear increase in percentage of pine blocks attacked by termites in the pine and hardwood forests and by the end of the growing season, nearly all had been channelized by termites. In the turkey oak habitat 70% of the pine blocks were channelized. Termites removed between 3% and 12% of the original mass of over one-fourth of the pine blocks during the growing season.Wood litter in fall was highest in the lowland hardwood forest: 2869 kg·ha^-1·yr^-1. Wood litter input in the long leaf pine plantation, 792 kg·ha^-1·yr^-1 was nearly equivalent to the three year average wood litter in fall in a Danish oak forest.     

Characterisation of thermally modified hard- and softwoods by C CPMAS NMR

The changes induced by thermal modification in the chemical structure of spruce [Picea abies (L.) Karst.], birch (Betula pendula), aspen (Populus tremula) and oak (Quercus robur) were studied by ¹³C CPMAS NMR spectroscopy. Spruce, birch and aspen were thermally modified at 195 °C and oak at 160 °C, under steam, according to an industrial-scale heat treatment process. In both hard- and softwood samples, ¹³C CPMAS NMR measurements revealed a degradation of less ordered carbohydrates (i.e. hemicelluloses and amorphous cellulose) in the thermally modified wood, which resulted in an increase in the cellulose crystallinity. Furthermore, thermal modification induced changes in the lignin structure by a cleavage of the β-O-4 linkages. In the softwood lignin, a decrease also occurred in the methoxyl group content leading to a more condensed lignin structure.     

Parameter-specific hydroclimatic sensitivity of a low-elevation network of living and historical tree-ring series from north-eastern Austria

Compared to the alpine regions of Austria, the eastern part of the country is overall warmer and drier with some tree species growing at the dry limit within their ecological range. This suggests that tree rings may be a valuable proxy for hydroclimatic variability. In this study, we develop ring-width, earlywood-width and latewood-width chronologies obtained from drought sensitive living trees and historical timber from one of the driest and warmest regions of Austria, the Weinviertel. For this, samples of four different tree species − fir (Abies alba Mill.), spruce (Picea abies (L.) Karst.), oak (Quercus petraea Liebl., Q. robur L., Q. cerris L.), and pine (Pinus sylvestris L., P. nigra Arnold) were collected from 88 sites (23 forest stands and 65 historical constructions). 1589 samples (oak: 592 samples, pine: 577, spruce: 212, fir: 208) were dated. Dendro-provenancing was required to ensure that only regional material has entered the chronologies. According to the analyses, historical pine and oak wood were nearly 100% regional, while spruce and fir wood were imported to a great extent with only 44% spruce and 35% fir confirmed to be regional. Because site conditions of historical wood samples are unknown but can have a significant influence on tree growth, changes to site replication over time were important in the assessment of chronology reliability. We also controlled for potential artificial increases in sample depth when more than one construction element is made from a single trunk.We assessed the pine (1584-2011 AD) and oak (1244-2011 AD) chronologies’ potential for reconstructing past hydroclimatic variability by means of response functions in a 17-months window from previous June to current October with climate data from three weather stations (Vienna, Retz, Brno) from 1897 to 2010 AD. The highest seasonal response coefficients are for oak and pine ring width (∼0.43) with respect to aggregated March to July precipitation totals and Thornthwaite climatic water balance. These chronologies reveal a high potential for estimating past changes in regional-scale moisture availability during the earlier growing season.     

Anaerobic Fermentation of Woody Biomass Pretreated with Supercritical Ammonia

The degradability of ground hardwood by thermophilic anaerobic bacteria (Clostridium thermocellum with or without Thermoanaerobacter strain B6A) was greatly enhanced by pretreatment of the substrate with supercritical ammonia. Relative to C. thermocellum monocultures, cocultures of C. thermocellum and Thermoanaerobacter strain B6A degraded 1.5-fold more pretreated soft maple but produced 2- to 5-fold more fermentation endproducts because Thermoanaerobacter sp. removed reducing sugars produced by C. thermocellum during the fermentation. Dry weight losses were not totally accounted for in end products, due to formation of partially degraded material (<0.4 μm diameter wood particles) during the fermentation. One pretreated hardwood, Southern red oak, was fermented poorly because it released soluble inhibitors at the 60°C incubation temperature. Considerable (6- to 11-fold) increases in substrate degradability were also noted for supercritical ammonia-pretreated wood materials fermented in an in vitro rumen digestibility assay. Degradation of pretreated softwoods by either thermophilic or mesophilic fermentation was not measurable under the conditions tested.     

The timing of bud burst and its effect on tree growth

A phenology model for estimating the timings of bud burst – one of the most influential phenological phases for the simulation of tree growth – is presented in this study. The model calculates the timings of the leafing of beech (Fagus sylvatica L.) and oak (Quercus robur L.) and the May shoot of Norway spruce (Picea abies L.) and Scots pine (Pinus sylvestris L.) on the basis of the daily maximum temperature. The data for parameterisation and validation of the model have been taken from 40 climate and 120 phenological stations in southern Germany with time series for temperature and bud burst of up to 30 years. The validation of the phenology module by means of an independent data set showed correlation coefficients for comparisons between observed and simulated values of 54% (beech), 55% (oak), 59% (spruce) and 56% (pine) with mean absolute errors varying from 4.4 days (spruce) to 5.0 days (pine). These results correspond well with the results of other – often more complex – phenology models. After the phenology module had been implemented in the tree-growth model BALANCE, the growth of a mixed forest stand with the former static and the new dynamic timings for the bud burst was simulated. The results of the two simulation runs showed that phenology has to be taken into account when simulating forest growth, particularly in mixed stands.     

Role of man in the history of vegetation of the Ellero valley (maritime Alps, Italy)

The pollen analysis of a sediment core from a peat bog (Rifugio Mondovi) at the mountain belt (1760 m) in the Ellero Valley (Italian Maritime Alps) shows the postglacial vegetation history. The sequence starts at 12,000 BP during a peak of pine pollen; this first phase shows a low representation of birch and the presence of Tilia. Younger Dryas is characterised by increasing percentages of Artemisia, showing the presence of deciduous Quercus, fir and beech. Elm appears at the beginning of the Holocene during the second pine peak (9800 BP). A 3000-year hiatus is present. Sedimentation resumes at 6000 BP in a Rhododendron fir-wood. The present timberline at 1500 m, at the limit of the beech wood, is a result of the decline of the fir-wood at 2600 BP, which allowed an expansion of beech. During this period, there was a continual increase in Gramineae and deciduous oak and the first occurrences of evergreen oak are observed. The development of larch occurs at 1800 BP, together with walnut, chestnut, cereals and vine.     

The Spatial Distribution of Fungi on Decomposing Woody Litter in a Freshwater Stream,Western Ghats,India

We mapped filamentous fungal association with mechanically “hard” and “soft” woody litter naturally deposited in a stream of the Western Ghats of India. Using a durometer (rubber hardness tester), the toughness of surface of wood collected from stream was determined by considering durometer reading from 60–72 to 30–37 as hardwood and softwood, respectively. From each wood (1.5 cm diameter), two segments each of 3 cm length were excised and vertically cut into nine sections comprising eight marginal and one central section. From three stream locations, hardwood and softwood sections were assessed for the occurrence of lignicolous and Ingoldian fungi. A first set of wood sections was incubated in damp chambers up to 4 months with periodical screening (every 2 weeks) for lignicolous fungi. Another set was incubated in bubble chambers up to 72 h to ascertain colonization of Ingoldian fungi. In hardwood sections, 17 lignicolous fungi (ascomycetes, four; mitosporic fungi, 13; mean, 6.8; range, 6–8/section) and ten Ingoldian fungi (mean, 2; range, 0–4/section) comprising nine lignicolous (11.1–40.7%) and three Ingoldian (11.1–14.8%) fungi as core-group taxa were recovered. In softwood, ten lignicolous fungi (ascomycetes, 0; mitosporic fungi, ten; mean, 3.8; range, 2–5/section) and 26 Ingoldian fungi (mean, 8.1; range, 5–10/section) comprising six lignicolous (11.1–85.2%) and 12 Ingoldian (11.1–88.9%) fungi as core-group taxa were recovered. The ratio of lignicolous fungi/Ingoldian fungi was higher in hardwood than softwood (1.7 vs. 0.4). The spore output of Ingoldian fungi was higher in softwood (mean, 901 g⁻¹; range, 80–2546 g⁻¹) than hardwood (mean, 21 g⁻¹; range, 0–140 g⁻¹). The Shannon diversity of lignicolous fungi was higher in hardwood than softwood (3.604 vs. 2.665), whereas it was opposite for Ingoldian fungi (3.116 vs. 3.918). The overall fungal diversity was higher in softwood than hardwood (4.413 vs. 4.219). The range of Jaccard’s index of similarity among wood sections was higher in lignicolous fungi (8–71% and 13–75%) than Ingoldian fungi (0–50% and 8–55%) in hardwood and softwood. The rarefaction indices of expected number of taxa against hardwood sections revealed higher and persistent lignicolous fungi than the Ingoldian fungi, while the Ingoldian fungi were persistent in softwood sections, although they were lower than lignicolous fungi. Our study demonstrated the dominance of lignicolous fungi and Ingoldian fungi in hardwood and softwood, respectively.     

Resistance of European tree species to drought stress in mixed versus pure forests: evidence of stress release by inter‐specific facilitation

While previous studies focused on tree growth in pure stands, we reveal that tree resistance and resilience to drought stress can be modified distinctly through species mixing. Our study is based on tree ring measurement on cores from increment boring of 559 trees of Norway spruce (Picea abies [L.] Karst.), European beech (Fagus sylvatica [L.]) and sessile oak (Quercus petraea (Matt.) Liebl.) in South Germany, with half sampled in pure, respectively, mixed stands. Indices for resistance, recovery and resilience were applied for quantifying the tree growth reaction on the episodic drought stress in 1976 and 2003. The following general reaction patterns were found. (i) In pure stands, spruce has the lowest resistance, but the quickest recovery; oak and beech were more resistant, but recover was much slower and they are less resilient. (ii) In mixture, spruce and oak perform as in pure stands, but beech was significantly more resistant and resilient than in monoculture. (iii) Especially when mixed with oak, beech is facilitated. We hypothesise that the revealed water stress release of beech emerges in mixture because of the asynchronous stress reaction pattern of beech and oak and a facilitation of beech by hydraulic lift of water by oak. This facilitation of beech in mixture with oak means a contribution to the frequently reported overyield of beech in mixed versus pure stands. We discuss the far‐reaching implications that these differences in stress response under intra‐ and inter‐specific environments have for forest ecosystem dynamics and management under climate change.     

Wood species utilization for timber constructions in the Czech lands over the period 1400–1900

Longstanding demographic growth accompanied by rising settlement activities and development of industry led to an increasing demand on utilization of wood. Tree species were selected for their specific properties. As a consequence of regional differences of forest species composition, wood has become an extremely important trade commodity. Therefore, the utilization of individual species could substantially change in space and time. In this study, we use 8´135 precisely dated timber constructions from a dendrochronological database to investigate spatio-temporal changes in wood utilization across the Czech lands from the 15th to the 19th century. Our results suggest that the utilization of individual species in historical timber constructions was primarily limited by their availability. Species selection was also based on wood properties and stem geometry. Most of historical constructions (99.7%), represented mainly by roofs and ceilings, are made of fir, spruce, pine, and oak. While fir constructions prevail in eastern Moravia and Silesia, spruce constructions are largely spread across the western and central part of the Czech Republic. Pine and oak constructions reflect natural occurrence of such forests in lower elevated central Bohemia and southern Moravia. Although fir prevailed in timber construction in the late-Medieval and post-Medieval times, planting of spruce monocultures resulted in its significantly increased utilization by the end of the 19th century. This study demonstrates the value of dendrochronological databases as an indicator of historical wood utilization.     

Study of microbial adhesion on some wood species: Theoretical prediction

The initial interaction between microorganisms and substrata is mediated by physicochemical forces, which in turn originate from the physicochemical surface properties of both interacting phases. In this context, we have determined the physicochemical proprieties of all microorganisms isolated from cedar wood decay in an old monument at the Medina of Fez-Morocco. The cedar wood was also assayed in terms of hydrophobicity and electron donor-electron acceptor (acid-base) properties. Investigations of these two aspects were performed by contact angles measurements via sessile drop technique. Except Bacillus subtilis strain (Giwi < 0), all strains studied showed positive values of the degree of hydrophobicity (Giwi > 0) and can therefore be considered as hydrophilic while cedar wood revealed a hydrophobic character (Giwi = 58.81 mJ m⁻²). All microbial strains were predominantly electron donor. The results show also that all strains were weak electron acceptors. Cedar wood exhibits a weak electron donor/acceptor character. Based on the thermodynamic approach, the Lifshitz-van der Waals interaction free energy, the acid-basic interactions free energy, the total interaction free energy between the microbial cells and six different wood species (cedar, oak, beech, ash, pine and teak) in aqueous media was calculated and used to predict which microbial strains have a higher ability to adhere to wooden surfaces. Except of weak wood, for all the situations studied, generalizations concerning the adhesion of the microbiata on wood species cannot be made and the microbial adhesion on wooden substrata was dependent on wood species and microorganisms tested.