Development of a novel FRET immunosensor technique

We report on a novel technique to develop an optical immunosensor based on fluorescence resonance energy transfer (FRET). IgG antibodies were labeled with acceptor fluorophores while one of three carrier molecules (protein A, protein G, or F(ab')2 fragment) was labeled with donor fluorophores. The carrier molecule was incubated with the antibody to allow specific binding to the Fc portion. The labeled antibody-protein complex was then exposed to specific and nonspecific antigens, and experiments were designed to determine the 'in solution' response. The paper reports the results of three different donor-acceptor FRET pairs, fluorescein isothiocyanate/tetramethylrhodamine isothiocyanate, Texas Red/Cy5, and Alexa Fluor 546/Alexa Fluor 594. The effects of the fluorophore to protein conjugation ratio (F/P ratio) and acceptor to donor fluorophore ratios between the antibody and protein (A/D ratio) were examined. In the presence of specific antigens, the antibodies underwent a conformational change, resulting in an energy transfer from the donor to the acceptor fluorophore as measured by a change in fluorescence. The non-specific antigens elicited little or no changes. The Alexa Fluor FRET pair demonstrated the largest change in fluorescence, resulting in a 35% change. The F/P and A/D ratio will affect the efficiency of energy transfer, but there exists a suitable range of A/D and F/P ratios for the FRET pairs. The feasibility of the FRET immunosensor technique was established; however, it will be necessary to immobilize the complexes onto optical substrates so that consistent trends can be obtained that would allow calibration plots.     

A novel FRET-based optical fiber biosensor for rapid detection of Salmonella typhimurium

A biosensor that is portable and permits on-site analysis of samples would significantly reduce the large economical burden of food products recalls. A fiber optic portable biosensor utilizing the principle of fluorescence resonance energy transfer (FRET) was developed for fast detection of Salmonella typhimurium (S. typhimurium) in ground pork samples. Labeled antibody-protein G complexes were formed via the incubation of anti-Salmonella antibodies labeled with FRET donor fluorophores (Alexa Fluor 546) and protein G (PG) labeled with FRET acceptor fluorophores (Alexa Fluor 594). Utilizing silanization, the labeled antibodies-PG complexes were then immobilized on decladded, tapered silica fiber cores to form the evanescent wave-sensing region. The biosensors were tested in two different solutions: (1) PBS doped with S. typhimurium and (2) homogenized pork sample with S. typhimurium. The fiber probes tested in a S. typhimurium doped phosphate buffered solution demonstrated the feasibility of the biosensor for detecting S. typhimurium as well as determined the optimal packing density of the labeled antibody-PG complexes on the surface of fibers. The results showed that a packing density of 0.033 mg/ml produced the lowest limit of detection of 10(3)cells/ml with 8.2% change in fluorescence. The fiber probes placed in homogenized pork samples inoculated with S. typhimurium showed a limit of detection of 10(5)CFU/g with a 6.67% in fluorescence within a 5-min response time. These results showed that the FRET-based fiber optic biosensor can become a useful analytical tool for detection of S. typhimurium in real food samples.     

Fluorescence of Alexa Fluor Dye Tracks Protein Folding

Fluorescence spectroscopy is an important tool for the characterization of protein folding. Often, a protein is labeled with appropriate fluorescent donor and acceptor probes and folding-induced changes in Förster Resonance Energy Transfer (FRET) are monitored. However, conformational changes of the protein potentially affect fluorescence properties of both probes, thereby profoundly complicating interpretation of FRET data. In this study, we assess the effects protein folding has on fluorescence properties of Alexa Fluor 488 (A488), which is commonly used as FRET donor. Here, A488 is covalently attached to Cys69 of apoflavodoxin from Azotobacter vinelandii. Although coupling of A488 slightly destabilizes apoflavodoxin, the three-state folding of this protein, which involves a molten globule intermediate, is unaffected. Upon folding of apoflavodoxin, fluorescence emission intensity of A488 changes significantly. To illuminate the molecular sources of this alteration, we applied steady state and time-resolved fluorescence techniques. The results obtained show that tryptophans cause folding-induced changes in quenching of Alexa dye. Compared to unfolded protein, static quenching of A488 is increased in the molten globule. Upon populating the native state both static and dynamic quenching of A488 decrease considerably. We show that fluorescence quenching of Alexa Fluor dyes is a sensitive reporter of conformational changes during protein folding.     

Fluorometric assay for quantitation of biotin covalently attached to proteins and nucleic acids

As a component of the (strept)avidin affinity system, biotin is often covalently linked to proteins or nucleic acids. We describe here a microplate-based high-throughput fluorometric assay for biotin linked to either proteins or nucleic acids based on fluorescence resonance energy transfer (FRET). This assay utilizes a complex of Alexa Fluoro 488 dye-labeled avidin with a quencher dye, 2-(4'-hydroxyazobenzene) benzoic acid (HABA), occupying the biotin binding sites of the avidin. In the absence of biotin, HABA quenches the fluorescence emission of the Alexa Fluor 488 dyes via FRET HABA is displaced when biotin binds to the Alexa Fluor 488 dye-labeled avidin, resulting in decreased FRET efficiency. This mechanism results in an increase in fluorescence intensity directly related to the amount of biotin present in the sample. The assay is able to detect as little as 4 pmol biotin in a 0.1 mL volume within 15 min of adding sample to the reagent, with a Z-factor > 0.9.     

DNA hybridization detection in a microfluidic channel using two fluorescently labelled nucleic acid probes

A conceptually new technique for fast DNA detection has been developed. Here, we report a fast and sensitive online fluorescence resonance energy transfer (FRET) detection technique for label-free target DNA. This method is based on changes in the FRET signal resulting from the sequence-specific hybridization between two fluorescently labelled nucleic acid probes and target DNA in a PDMS microfluidic channel. Confocal laser-induced microscopy has been used for the detection of fluorescence signal changes. In the present study, DNA hybridizations could be detected without PCR amplification because the sensitivity of confocal laser-induced fluorescence detection is very high. Two probe DNA oligomers (5'-CTGAT TAGAG AGAGAA-TAMRA-3' and 5'-TET-ATGTC TGAGC TGCAGG-3') and target DNA (3'-GACTA ATCTC TCTCT TACAG GCACT ACAGA CTCGA CGTCC-5') were introduced into the channel by a microsyringe pump, and they were efficiently mixed by passing through the alligator teeth-shaped PDMS microfluidic channel. Here, the nucleic acid probes were terminally labelled with the fluorescent dyes, tetrafluororescein (TET) and tetramethyl-6-carboxyrhodamine (TAMRA), respectively. According to our confocal fluorescence measurements, the limit of detection of the target DNA is estimated to be 1.0 x 10(-6) to 1.0 x 10(-7)M. Our result demonstrates that this analytical technique is a promising diagnostic tool that can be applied to the real-time analysis of DNA targets in the solution phase.     

Quantitative Assessment of Antibody Internalization with Novel Monoclonal Antibodies against Alexa Fluorophores

Antibodies against cell surface antigens may be internalized through their specific interactions with these proteins and in some cases may induce or perturb antigen internalization. The anti-cancer efficacy of antibody-drug conjugates is thought to rely on their uptake by cancer cells expressing the surface antigen. Numerous techniques, including microscopy and flow cytometry, have been used to identify antibodies with desired cellular uptake rates. To enable quantitative measurements of internalization of labeled antibodies, an assay based on internalized and quenched fluorescence was developed. For this approach, we generated novel anti-Alexa Fluor monoclonal antibodies (mAbs) that effectively and specifically quench cell surface–bound Alexa Fluor 488 or Alexa Fluor 594 fluorescence. Utilizing Alexa Fluor–labeled mAbs against the EphA2 receptor tyrosine kinase, we showed that the anti-Alexa Fluor reagents could be used to monitor internalization quantitatively over time. The anti-Alexa Fluor mAbs were also validated in a proof of concept dual-label internalization assay with simultaneous exposure of cells to two different mAbs. Importantly, the unique anti-Alexa Fluor mAbs described here may also enable other single- and dual-label experiments, including label detection and signal enhancement in macromolecules, trafficking of proteins and microorganisms, and cell migration and morphology.     

Fluorescent resonance energy transfer (FRET) based detection of a multiplex ligation-dependent probe amplification assay (MLPA) product

A fluorescent resonance energy transfer (FRET)-based hybridization assay for detecting multiplex ligation-dependent probe amplification (MLPA) products has been developed, extending the diagnostic power of the technique and demonstrating the possibility of combining MLPA with microarrays for the detection of multiple mutations. FRET is one of the most commonly used detection techniques for hybridization assays. To investigate the applicability of FRET based detection of MLPA products, a sandwich assay was designed to detect gene copy number by exploiting an immobilized probe labeled with an acceptor dye, Alexa Fluor 555, which hybridises to specific PCR amplicons, followed by hybridization of a second probe labeled with the donor dye, Alexa Fluor 488. Following excitation of the Alexa Fluor 488, a FRET signal was produced only if a DNA sequence specific to the BRCA1 exon 13 was present in the test sample. We have verified this assay on a DNA sample of a patient carrying a heterozygous BRCA1 exon 13 deletion using male genomic DNA as control. Here we demonstrate that the DNA sample containing the heterozygous deletion generated a considerably reduced FRET signal as compared to the control male human DNA. Our results show that the FRET design presented in this study can differentiate between reduced copy numbers any genomic DNA sequence after MLPA analysis, and the reported format is applicable to multiplex detection of MLPA products, using microarrays, or optical biosensor arrays, and future work will focus on the demonstration of this.     

Immunofluorescent test for simultaneous detection of Edwardsiella ictaluri and Flavobacterium columnare

Enteric septicemia of catfish (ESC) and columnaris disease are 2 bacterial diseases significantly affecting the aquaculture industry, and thus rapid diagnosis of disease is imperative for making judicious management decisions. A rapid indirect fluorescent antibody (IFA) test with antibody conjugated fluorochromes having 2 different spectral properties (Alexa Fluor 488-emitting green fluorescence, and Alexa Fluor 594-emitting red fluorescence) was compared with bacteriological culture (accepted standard) for simultaneous detection of Edwardsiella ictaluri (EI) and Flavobacterium columnare (FC) in 3 groups of experimentally infected channel catfish (Ictalurus punctatus Rafinesque), and a fourth group that acquired an aquarium-infection with F. columnare. A total of 303 samples (derived from kidney, brain and nares) from 101 fish were concurrently examined by both tests. Fish in the 3 experimentally infected groups (I to III) were culture positive for the bacteria with which they were infected, and fish in Group IV, (the spontaneously infected fish) revealed F. columnare only. The IFA test compared favorably in sensitivity (EI= 80.7 %; FC = 87.2%) and specificity (EI = 83.9%; FC = 88.9%) with the standard bacteriological culture. The positive predictive value (EI = 96.2% Group I, 90.8% Group II, 93.7% Groups I and II combined; FC = 95.2% Group II, 95.3% Groups II, III and IV combined) was high, while the negative predictive value (EI = 66.7% Group I, 31.3% Group II, 59.5% Groups I and II combined; FC = 73.7% Group II, 72.7% Groups II, III and IV combined) was relatively low. The IFA test will serve as an efficient tool for rapid simultaneous detection of E. ictaluri and F. columnare in outbreaks of disease.     

Real-time closed tube single nucleotide polymorphism (SNP) quantification in pooled samples by quencher extension (QEXT)

Quencher extension (QEXT) is a novel single step closed tube real-time method to quantify SNPs using reporters and quenchers in combination with primer extension. A probe with a 5′-reporter dye is single base extended with a dideoxy nucleotide containing a quencher dye if the target SNP allele is present. The extension is recorded from the quenching (reduced fluorescence) of the reporter dye. This avoids the influence of the unincorporated dye-labeled nucleotides, resulting in high accuracy and a high signal-to-noise ratio. The relative amount of a specific SNP allele is determined from the nucleotide incorporation rate in a thermo-cycling reaction. We tested the QEXT assay using five SNPs in the Listeria monocytogenes inlA gene as a model system. The presence of the target SNP alleles was determined with high statistical confidence (P < 0.0005). The quantitative detection limits were between 0 and 5% for the targeted SNP alleles on a background of other SNP alleles (P < 0.05). The QEXT method is directly adaptable to current real-time PCR equipment and is thus suited for high throughput and a wide application range.     

Development of DNA Aptamers to a Foot-and-Mouth Disease Peptide for Competitive FRET-Based Detection

We sought to develop a novel competitive fluorescence resonance energy transfer (FRET)-aptamer-based strategy for detection of foot-and-mouth (FMD) disease within minutes. A 14-amino-acid peptide from the VP1 structural protein, which is conserved among 16 strains of O-serotype FMD virus, was synthesized and labeled with Black Hole Quencher-2 (BHQ-2) dye. Polyclonal FMD DNA aptamers were labeled with Alexa Fluor 546-14-dUTP by polymerase chain reaction and allowed to bind the BHQ-2-peptide conjugate. Following purification of the FRET–aptamer–peptide complex, a “lights off” response was observed within 10 minutes and was sensitive to a level of 25–250 ng/mL of FMD peptide. Ten candidate aptamers were sequenced from the polyclonal family. The aptamer candidates were screened in an enzyme-based plate assay. A high- and low-affinity aptamer candidate were each labeled with Alexa Fluor 546-14-dUTP by asymmetric polymerase chain reaction and used in the competitive FRET assay, but neither matched the sensitivity of the polyclonal FRET response, indicating the need for further screening of the aptamer library.     

Violet laser diodes in flow cytometry: an update.

INTRODUCTION: In previous studies we and others have demonstrated the usefulness of violet laser diodes (VLDs) as replacement laser sources for krypton-ion lasers on stream-in-air cytometers. Previously available VLDs had a maximum available power of less than 25 mW; this was sufficient for excitation of densely labeled cell surface antigens using fluorochromes such as Cascade Blue or Pacific Blue, but may have been insufficient for applications requiring higher levels of photon saturation, such as low-level expression of Cyan Fluorescent Protein (ECFP) in CFP-YFP FRET applications. In this follow-up study, we have tested more powerful VLDs emitting at 55 mW, and a beam-merged dual module VLD with 100 mW combined output, for their ability to excite a variety of violet-excited fluorochromes, including CFP. METHODS: A dual module VLD (two linear polarized VLDs with their beams merged by a polarized beam combiner) emitting at 404 nm was mounted on a BD FACSVantage DiVa stream-in-air cytometer. The individual polarized 55 mW beams or the 100 mW combined beams were used to analyze PBMCs labeled with the violet-excited probes Cascade Blue, Alexa Fluor 405, Cascade Yellow and Pacific Orange dyes. Violet-excited fluorescent microsphere mixtures with decreasing fluorescence levels were also used to detect the minimum sensitivity threshold and precision of these lasers. VLD excitation on a gel-coupled cuvette flow cytometer was used as a sensitivity baseline. RESULTS: The dual module 100 mW VLD gave both sensitivity and precision levels approaching that observed for lower-power sources on a cuvette cytometer. Single polarized VLD modules at 55 mW gave slightly decreased sensitivity for the microspheres standards and all the tested fluorochromes compared to the 100 mW source. CONCLUSIONS: While 55 mW laser sources performed adequately in the stream-in-air format, increasing the power to 100 mW did give a small but detectable increase in instrument sensitivity. This sensitivity level approached that of cuvette systems.     

Triple-FRET Technique for Energy Transfer Between Conjugated Polymer and TAMRA Dye with Possible Applications in Medical Diagnostics

Three-component Förster resonance energy transfer (FRET) has been used to obtain efficient FRET between the cationic conjugated polymer (CCP) as donor and 5-carboxy tetramethylrhodamine (TAMRA) dye as acceptor, by using an intermediate donor, fluorescein. In spite of the fact that there is enough overlap between the emission spectra of CCP and absorption spectra of TAMRA, the efficiency of FRET between CCP and TAMRA is poor. The reason for this is that while the Förster critical distance is not very sensitive to the overlap, the FRET efficiency is extremely sensitive to it. However, it is observed that the FRET efficiency between CCP and TAMRA improves considerably when fluorescein is introduced in the solution. The triple FRET so obtained can be used for deoxyribonucleic acid sequence detection in medical diagnostics because the fluorescence emission from TAMRA is pH-insensitive.     

Possible sources of dye-related signal correlation bias in two-color DNA microarray assays

DNA microarray analyses commonly use two spectrally distinct fluorescent labels to simultaneously compare different mRNA pools. Signal correlation bias currently limits accepted resolution to twofold changes in gene expression. This bias was investigated by (i) examining fluorescence and absorption spectra and changes in relative fluorescence of DNAs labeled with the Cy3, Cy5, Alexa Fluor 555, and Alexa Fluor 647 dyes and by (ii) using homotypic hybridization assays to compare the Cy dye pair with the Alexa Fluor dye pair. Cy3 or Cy5 dye-labeled DNA exhibited reduced fluorescence and absorption anomalies that were eliminated by nuclease treatment, consistent with fluorescence quenching that arises from dye-dye or dye-DNA-dye interactions. Alexa Fluor 555 and Alexa Fluor 647 dye-labeled DNA exhibited little or no such anomalies. In microarray hybridization, the Alexa Fluor dye pair provided higher signal correlation coefficients (R2) than did the Cy dye pair; at the 95% prediction level, a 1.3-fold change in gene expression was significant using the Alexa Fluor dye pair. Lowered signal correlation of the Cy dye pair was associated with high variance in Cy5 dye signals. These results indicate that fluorescence quenching may be a source of signal bias associated with the Cy dye pair.     

Caspase-3 sensitive signaling in vivo in apoptotic HeLa cells by chemically engineered intramolecular fluorescence resonance energy transfer mutants of green fluorescent protein

Green fluorescent protein (UV5) was re-engineered to remove native cysteine residues, and a new cysteine was introduced near the C-terminus, approximately 20 A from the native fluorophore, for site-specific attachment of chemical fluorophores. The resultant efficient intramolecular FRET quenched GFP emission and gave a new emission band from the conjugated fluorophore. Caspase-3 cleavage of constructs with a caspase-3 sequence near the C-terminus in the sequence between the native fluorophore and the new cysteine, located C-terminal to the caspase site, destroyed the FRET, the emitted color reverting to that of unmodified GFP. This process was demonstrated in vitro with caspase-3 and lysates from cells undergoing apoptosis. Real-time emission changes for the Alexa Fluor 532 conjugate of this GFP, studied quantitatively in vivo for single HeLa cells using the ratios of fluorescence at the red and green maxima by confocal microscopy, showed that caspase-3 action in the cytosol preceded that in the nucleus.     

A fluorescence resonance energy transfer-based approach for investigating late endosome-lysosome retrograde fusion events

Traditionally, lysosomes have been considered to be a terminal endocytic compartment. Recent studies suggest that lysosomes are quite dynamic, being able to fuse with other late endocytic compartments as well as with the plasma membrane. Here we describe a quantitative fluorescence energy transfer (FRET)-based method for assessing rates of retrograde fusion between terminal lysosomes and late endosomes in living cells. Late endosomes were specifically labeled with 800-nm latex beads that were conjugated with streptavidin and Alexa Fluor 555 (FRET donor). Terminal lysosomes were specifically labeled with 10,000-MW dextran polymers conjugated with biotin and Alexa Fluor 647 (FRET acceptor). Following late endosome-lysosome fusion, the strong binding affinity between streptavidin and biotin brought the donor and acceptor fluorophore molecules into close proximity, thereby facilitating the appearance of a FRET emission signal. Because apparent size restrictions in the endocytic pathway do not permit endocytosed latex beads from reaching terminal lysosomes in an anterograde fashion, the appearance of the FRET signal is consistent with retrograde transport of lysosomal cargo back to late endosomes. We assessed the efficiency of this transport step in fibroblasts affected by different lysosome storage disorders—Niemann-Pick type C, mucolipidosis type IV, and Sandhoff’s disease, all of which have a similar lysosomal lipid accumulation phenotype. We report here, for the first time, that these disorders can be distinguished by their rate of transfer of lysosome cargos to late endosomes, and we discuss the implications of these findings for developing new therapeutic strategies.     

肌动蛋白结合脂筏促进巨噬细胞摄入土拉弗朗西斯菌

观察土拉弗朗西斯菌LVS借助脂筏以肌动蛋白为动力被鼠巨噬细胞摄入的过程。细胞胆固醇用菲律平Ⅲ染色,结合神经节苷酯GM1的霍乱毒素B亚基用键合了Alexa 594的兔抗霍乱毒素B亚基二抗显色;肌动蛋白用键合了Alexa 594的鬼笔环肽显色。免疫荧光显微镜观察到脂筏成分中的胆固醇、神经节苷酯GM1均可与细菌共定位;胆固醇可与肌动蛋白共定位。随着感染时间的延长,细菌可离开脂筏。离开脂筏的细菌囊泡可与肌动蛋白共定位。这些发现提示肌动蛋白与脂筏结合,在弗朗西斯菌早期进入巨噬细胞期间发挥重要作用。     

Fluorescence resonance energy transfer in ferritin labeled with multiple fluorescent dyes

We simultaneously labeled ferritin with two Alexa Fluor fluorophores (AF350 and AF430). When both fluorophores label the same ferritin subunit, fluorescence resonance energy transfer (FRET) takes place from the excited AF350 to the acceptor AF430. By varying the number and the ratio of labeling fluorophores, we can modulate FRET such that the ferritin particles can exhibit multiple colors under UV illumination. Labeling of the ferritin shell does not affect the properties of the metallic core. Electronic supplementary material The online version of this article (doi:) contains supplementary material, which is available to authorized users.     

Observation of protein folding/unfolding dynamics of ubiquitin trapped in agarose gel by single-molecule FRET

A ubiquitin mutant with two Cys mutations, m[C]q/S65C, was site-specifically labeled with two dye molecules, Alexa Fluor 488 (donor) and Alexa Fluor 594 (acceptor), due to the different reactivity of these two Cys residues. This doubly dye-labeled ubiquitin has lower structural stability than wild-type ubiquitin. Taking advantage of this decreased stability, conformational heterogeneity of this protein under nondenaturing condition was observed at the single-molecule level using single-paired Förster resonance energy transfer (FRET) by trapping the protein in agarose gel. Three conformational populations corresponding to folded (E _ET ≈ 0.95), loosely packed (E _ET ≈ 0.72), and unfolded (E _ET ≈ 0.22) structures, and the structural transitions between them were observed. Our results suggest that agarose immobilization is good for observing structural dynamics of proteins under native condition.