尿样中三种蛋白质的毛细管电泳分离检测方法研究

目的:建立毛细管电泳分离测定人尿样中转铁蛋白、白蛋白和血红蛋白的新方法.方法:通过选择运行缓冲溶液种类及浓度、pH、表面活性荆种类及浓度、分离电压、进样时间对蛋白质分离效果的影响,优化了毛细管电泳法分离转铁蛋白、白蛋白和血红蛋白的条件.结果:利用此方法测定三种蛋白质的含量,浓度在0.01到1.00 g L-1范围内与峰电流呈良好的线性关系,检出限均为10-4 g L-1.结论:所建立的方法用于人尿样中转铁蛋白、白蛋白和血红蛋白的测定,结果满意.     

Optimization of capillary coating by hydroxyethyl methacrylate for capillary zone electrophoresis of proteins

This work describes further improvements of coating fused silica capillaries with 2-hydroxyethyl methacrylate (HEMA) by atom transfer radical polymerization (ATRP). First, endcapping with a sterically less bulky silanyl reagent reduces the electrosmotic flow (EOF) by 25% in addition to the 40% EOF reduction caused by HEMA coating compared to a bare fused silica capillary. An additional hydrolysis step was introduced into the preparation of HEMA coated capillaries and leads to better reproducible migration times. The influence of the solvent during ATRP and the resulting polymer coating was investigated by replacement of DMF with water or water-methanol mixtures. The quality of the optimized coating was characterized by protein separations at pH 3. HEMA coated capillaries reveal up to 746000 plates. The polyvinyl alcohol (PVA) coated capillary provides only half of this efficiency. A long-term test at pH 9 shows good stability of the HEMA coated capillaries in basic medium. Also the numbers of plates in this medium was about 30% higher than for separations with the PVA capillary. In addition, the phosphate buffer was replaced by a volatile ammonium acetate buffer for later use with mass spectrometry (MS).     

Identifying kinetically stable proteins with capillary electrophoresis

Unlike most proteins, which are in equilibrium with partially and globally unfolded conformations, kinetically stable proteins (KSPs) are trapped in their native conformations and are often resistant to harsh environment. Based on a previous correlation between kinetic stability (KS) and a protein's resistance to sodium dodecyl sulfate (SDS), we show here a simple method to identify KSPs by SDS‐capillary electrophoresis (CE). Control non‐KSPs were fully denatured by SDS and formed protein:SDS complexes that exhibited similar mobility in CE. In contrast, KSPs bound fewer SDS molecules, and showed a very different migration time and peak pattern in CE, thereby providing some insight about the structural heterogeneity of SDS:protein complexes and the relative KS of the various proteins.     

Determination of poorly separated monoclonal serum proteins by capillary zone electrophoresis

A capillary zone electrophoresis (CZE) technique was developed for the determination of poorly separated monoclonal serum proteins by agarose gel electrophoresis (AGE). A P/ACE 5500 capillary instrument (Beckman) was used under the following conditions: 57 cm x 50 microm I.D. fused-silica capillary, pH 9.6 borate buffer, and 214 nm on-line detection. Sixty patients (61 +/- 13 years) with a well isolated (n=24, group A) or poorly separated monoclonal band(s) by AGE (n=36, group B) were included in this study. Within- and between-run precision for CZE was below 4% for albumin and 7% for gamma-globulin. A 100% (group A) or 61% agreement (group B, more bands detected by CZE in 10 cases) was obtained between CZE and AGE for the number of monoclonal bands. In group B, quantification was possible in 92% of samples by CZE vs. 64% by AGE (P<0.05, chi-square). The proposed CZE method appears as an additional helpful technique for the determination of poorly separated monoclonal serum proteins by AGE.     

Completely monodisperse, highly repetitive proteins for bioconjugate capillary electrophoresis: development and characterization

Protein-based polymers are increasingly being used in biomaterial applications because of their ease of customization and potential monodispersity. These advantages make protein polymers excellent candidates for bioanalytical applications. Here we describe improved methods for producing drag-tags for free-solution conjugate electrophoresis (FSCE). FSCE utilizes a pure, monodisperse recombinant protein, tethered end-on to a ssDNA molecule, to enable DNA size separation in aqueous buffer. FSCE also provides a highly sensitive method to evaluate the polydispersity of a protein drag-tag and thus its suitability for bioanalytical uses. This method is able to detect slight differences in drag-tag charge or mass. We have devised an improved cloning, expression, and purification strategy that enables us to generate, for the first time, a truly monodisperse 20 kDa protein polymer and a nearly monodisperse 38 kDa protein. These newly produced proteins can be used as drag-tags to enable longer read DNA sequencing by free-solution microchannel electrophoresis.     

Laser-induced fluorescence technique for DNA and proteins separated by capillary electrophoresis

Recent developments in capillary electrophoresis (CE) in conjunction with laser-induced fluorescence (LIF) using long-wavelength (maximum excitation wavelength>500 nm) dyes are reviewed. These dyes are particularly of interest when conducting the analyses of biopolymers by CE-LIF using He-Ne lasers. These systems are benefited from low background, low costs, easy maintenance, and compactness. Derivatizations of DNA and proteins with fluorescent or nonfluorescent chemicals can be carried out prior to, during, or after separations. With the advantages of sensitivity, rapidity, and high efficiency, the applications of CE-LIF to the analysis of polymerase chain reaction products, DNA sequencing, trace analysis of proteins, and single cell analysis have been presented.     

Surface characterization and on-line activity measurements of microorganisms by capillary zone electrophoresis

Capillary zone electrophoresis (CZE) was applied to the electrophoretic characterization for microorganisms. The electrophoretic peaks detected using light scattering phenomena were characteristic of the microorganisms used. The electrophoretic mobility (μ) evaluated by CZE was in good agreement with that obtained by classical electrophoresis of microorganisms. The migration time was reproducible and depended on the ionic strength (I). Analysis of the μ vs. I relationship provided information regarding the charge density and the hardness of the microbial cell surface. The redox enzymatic activity of microorganisms was also evaluated by CZE using a running buffer containing a corresponding substrate and an appropriate exogenous electron acceptor. A decrease in the concentration of the electron acceptor due to microbial activity can be simultaneously monitored during the electrophoretic process without significant modification of the CZE instrument. Effects of some chemical treatments of microbial cells were also studied using this technique.     

Separation, identification, and characterization of microorganisms by capillary electrophoresis.

The use of capillary electrophoresis (CE) for the analysis, identification, and characterization of microorganisms has been gaining in popularity. The advantages of CE, such as small sample requirements, minimal sample preparation, rapid and simultaneous analysis, ease of quantitation and identification, and viability assessment, make it an attractive technique for the analysis of microbial analytes. As this instrumental method has evolved, higher peak efficiencies have been achieved by optimizing CE conditions, such as pH, ionic strength, and polymer additive concentration. Experimental improvements have allowed better quantitation and more accurate results. Many practical applications of this technique have been investigated. Viability and identification of microbes can be accomplished in a single analysis. This is useful for evaluation of microbial analytes in consumer products. Diagnosis of microbe-based diseases is now possible, in some cases, without the need for culture methods. Microbe-molecule, virus-antibody, or bacteria-antibiotic interactions can be monitored using CE, allowing for the screening of possible drug candidates. Fermentation can be monitored using this system. This instrumental approach can be adapted to many different applications, including assessing the viability of sperm cells. Progress has been made in the development of microelectrophoresis instrumentation. These advances will eventually allow the development of small, dedicated devices for the rapid, repetitive analyses of specific microbial samples. Although these methods may never fully replace traditional approaches, they are proving to be a valuable addition to the collection of techniques used to analyze, quantitate, and characterize microbes. This review outlines the recent developments in this rapidly growing field.     

Analysis of proteins in microsamples of rat airway surface fluid by capillary electrophoresis

A thin layer of airway surface fluid (ASF) lining the pulmonary airways plays an important role in the primary defense mechanisms of the lung against bacterial infection. However, little is known about the composition of ASF due to the thinness (typically 5–30 μm in healthy animals) of the fluid layer and its relative inaccessibility, which causes considerable difficulties in sample collection and subsequent analysis. We have used a novel technique of capillary sampling coupled with capillary electrophoresis (CE) to analyze the protein composition of rat ASF. CE analyses were performed under two different conditions: a borate buffer, pH 9.1, or a phosphate buffer, pH 2.5, with 0.5 mM spermine. The different selectivities afforded by the two methods aid in peak identification, and quantitation of most of the major species was possible using both separation conditions. Albumin, transferrin and globulins are observed to be the major protein components in rat ASF, at concentrations of 28 mg ml⁻¹, 4.0 mg ml⁻¹ and 34 mg ml⁻¹ respectively, in comparison to 31 mg ml⁻¹, 3.1 mg ml⁻¹ and 40 mg ml⁻¹, respectively, in rat plasma.     

Coated capillaries and additives for the separation of proteins by capillary zone electrophoresis and capillary isoelectric focusing

Strategies reported for the separation of proteins in capillary zone electrophoresis and capillary isoelectric focusing are reviewed. The strategies are grouped into two categories: coated capillaries and buffer/sample additives. Success attained with each case and also, more importantly, the limitations of the methodology are discussed. Recent results from our own laboratory in the area of capillary isoelectric focusing in uncoated, fused silica capillaries using additives are summarized. The advantages and disadvantages of coated columns vs. additives are delineated.     

Diagnosing AICA-ribosiduria by capillary electrophoresis

AICA-ribosiduria is a recently discovered inherited metabolic disease caused by a defect in final steps of purine de novo biosynthesis-5-amino-4-imidazolecarboxamide ribotide (AICAR)-transformylase/inosinemonophosphate (IMP)-cyclohydrolase (ATIC). A rapid and selective capillary electrophoretic method for screening of patients with AICA-ribosiduria is described. The method is based on direct ultraviolet detection of 5-amino-4-imidazolecarboxamide (AICA) and 5-amino-4-imidazolecarboxamide riboside (AICAr) in untreated urine. Background electrolyte consists of 100mM malonic acid adjusted with gamma-aminobutyric acid (pH 2.7). Under the given separation conditions both compounds of interest are well separated from other substances with separation efficiency of 1020000 and 130000 theoretical plates/m for AICA and AICAr, respectively. Total analysis time is 3 min with the limits of detection of 3.6 microM and 4.5 microM for AICA and AICAr, respectively. The usefulness of the presented method for screening of patients with ATIC deficiency is demonstrated on samples of Chinese hamster ovary cell line defective in ATIC activity, spiked urine samples and urine samples from patients treated with high-dose MTX which do not excrete increased amounts of AICA and AICAr compared to untreated controls (p<0.05). The described method is fast and effective enough for diagnostic applications.     

Myoglobinuria detection by capillary electrophoresis

Capillary electrophoresis was used in this study to separate urinary myoglobin from hemoglobin based on its electrophoretic mobility. Urine was applied directly without any treatment. The separation was accomplished in less than 7 min. Myoglobin extracted from human muscle tissues was separated, in a borate buffer 150 mM, pH 8.7 containing 0.5% polyethyleneglycol at 6 kV, into two peaks (MI and MII) which were also resolved far from hemoglobin. Upon standing at room temperature, MII converted into MI. Horse myoglobin eluted close to MI.The addition of polyethyleneglycol to the buffer enhanced the separation and increased the peak height of myoglobin. Optimum conditions for the separation are discussed. The method is suitable for routine clinical analysis because of its simplicity and speed.     

Recent advances in enantiomer separations by affinity capillary electrophoresis using proteins and peptides

Enantiomer separations by capillary electrophoresis (CE), using proteins as chiral selectors--affinity capillary electrophoresis (ACE) with free solutions and capillary electrochromatography (CEC)--with protein immobilized capillaries, are reviewed. The separation principle, recent advances in this field and some interesting topics are presented. In ACE, various enantiomer separations have been already reported using either plasma proteins or egg white ones. Miscellaneous proteins were also explored in the last few years. On the contrary, only a limited number of enantiomer separations have been successfully achieved in CEC. CEC is not yet mature enough to date, and further investigations, such as efficiency, durability and reproducibility of capillaries, will be necessary for the use of routine analyses. The study of enantioselective drug-protein binding is important in pharmaceutical developments. Some applications including high-performance CE/frontal analysis (HPCE/FA) are introduced in this paper.     

On-line concentration of microheterogeneous proteins by capillary electrophoresis using SDS and PEO as additives

In this paper, we describe a method for analyzing large-volume protein samples using capillary electrophoresis in conjunction with laser-induced fluorescence detection (CE-LIF). To improve the stacking and separation efficiencies of proteins, we added either 0.01% sodium dodecyl sulfate (SDS) or 0.01% poly(ethylene oxide) (PEO) to the Tris-borate solutions (pH 10.0) used to prepare the protein samples. After injection of the large-volume samples (ca. 1.0 microL, 0.1 microM), the proteins migrate against the electroosmotic flow (EOF) and enter the PEO zone; this process causes them to slow and stack at the boundary between the PEO and sample zones. As a result, the limits of detection (LODs) at a signal-to-noise (S/N) of 3 for most proteins are sub-nM to several nM. For instance, the LOD (S/N = 3) for alpha-lactalbumin is 0.48 nM, which is an 84-fold sensitivity enhancement over the traditional method. By applying a short plug of 0.2% SDS prior to sample injection, a greater number of peaks, representing the microheterogeneity of the proteins, were resolved and the stacking efficiency of the proteins increased slightly. This method allowed us to detect 12 peaks when injecting a large volume of sample containing six model proteins (0.1 microM). We also analyzed the microheterogeneities of the proteins by using CE with UV-Vis absorption detection when injecting a large volume of sample containing six model proteins (1.0 microM) in the presence of a 1.0% SDS plug. The practical method is validated by the detection of human serum albumin in a urine sample, obtained from a healthy female, without sample pretreatment; its concentration was 0.18 microM. We further demonstrate the capability of this method to detect low amounts of proteins through the detection of 45 nM hemoglobin after injecting ca. 1.0 microL of ultradilute lysed red blood cells. The experimental results indicate that our proposed method has great potential for use in diagnosis and proteomics applications.     

Oligonucleotide analysis by gel capillary electrophoresis

Several million oligonucleotides are synthesized each year for a broad variety of molecular biology applications. Steady improvements in the synthesis chemistry efficiency and the automated DNA synthesizers have made production of oligonucleotides routine and reliable. Many applications, such as PCR and sequencing, are often successful when the primers have not been rigorously purified. To ensure an adequate level of quality and purity, rapid and convenient analytical methods are necessary for the dozens of oligonucleotides produced each day by a DNA synthesis laboratory. Traditional methods of analysis have been HPLC and polyacrylamide slab tel electrophoresis (PAGE). Gel capillary electrophoresis is a new option, combining the advantages of the HPLC and PAGE, with unprecedented resolution and speed.     

Serum lamotrigine analysis by capillary electrophoresis

Lamotrigine, a new antiepileptic drug, is analyzed by capillary zone electrophoresis. Samples were deproteinized with acetonitrile containing an internal standard, acidified with dilute acetic acid and injected into the capillary. The drug migrated rapidly with the cationic compounds in about 3.5 min far from any interfering substances. The test was linear between 0.5–10 mg/l. The analysis time was about 5 min. The CE values correlated well with an HPLC method (r=0.97; n=35). The mean serum concentration of 121 patients on this drug was 3.7 mg/l. Incubating the serum with ß-glucuronidase for 1 h increased the peak height of lamotrigine by about 24%.     

Selectivity change in the separation of proteins and peptides by capillary electrophoresis using high-molecular-mass polyethyleneimine

A study of the capillary electrophoretic separations of proteins and peptides using high-molecular-mass polyethyleneimine (PEI) is presented. Experiments were performed in the PEI-coated capillaries together with the use of this polymer as a buffer additive under different separation conditions. The effects of pH and the concentration of PEI in the buffer on the electroosmotic flow and the migration orders of biopolymers were investigated. The use of the cationic polymer offers an alternative for the modification of the separation selectivity and resolution of biopolymers.     

Estimation of binding constants by capillary electrophoresis

Capillary electrophoresis (CE) has become a useful technique for measuring binding constants. This review is focused on recent trends in the estimation of binding constants by affinity CE. First, we introduce several mathematical equations in which it is assumed that the stoichiometry of the binding between drug and protein is 1:1 as a simple model. In order to calculate accurate binding constants by affinity CE, several experimental considerations are described in this review. In addition, some recent methodologies, such as partial filling technique and multiple-step ligand injection method, are introduced. Among research publications within 3 years, recent applications for determining binding constants are reviewed.     

Noncovalent labeling of proteins in capillary electrophoresis with laser-induced fluorescence detection

Interest in the use of capillary electrophoresis (CE) as a tool for protein separations continues to grow. Additionally, laser-induced fluorescence (LIF) detection schemes promise ultrasensitive detection of small quantities of these important biomolecules following their separation. In most cases, LIF detection of proteins necessitates their prior derivatization with a fluorescent label molecule. To minimize the amount of additional sample handling and time associated with such labeling procedures, not to mention the sometimes-stringent pH and temperature controls they require, noncovalent labeling is presented as a viable alternative. This review article considers established methods for noncovalent labeling of proteins for their subsequent analysis by CE-LIF. Label molecules suitable for excitation and emission in the ultraviolet, visible, and near-infrared regions of the spectrum are enumerated for a variety of protein analytes.