Enumeration of heterotrophs, fecal coliforms and Escherichia coli in water: comparison of 3M Petrifilm plates with standard plating procedures

A total of 177 naturally contaminated water samples were analyzed by membrane filtration according to the Standard Methods for the Examination of Water and Wastewater published by the American Public Health Association. Filters were incubated in parallel on mHPC-agar and 3M™ Petrifilm™ Aerobic Count Plates (Petrifilm™ AC plates) for heterotrophic counts. Fecal coliforms and Escherichia coli were enumerated on mFC-agar and 3M™ Petrifilm™ E. coli/Coliform Count Plates (Petrifilm™ EC plates). Typical colonies on each media type were confirmed following standard procedures. Heterotrophic counts were between 10³ and 10⁴ CFU/mL and the average log₁₀ counts obtained on Petrifilm™ AC plates were about two-fold lower than on mHPC-agar. Counts for fecal coliforms and E. coli were between 10² and 10³ CFU/mL. Average log₁₀ counts for confirmed fecal coliforms obtained on Petrifilm™ EC plates were slightly lower than on mFC agar with a correlation coefficient of 0.949. The average log₁₀ counts for confirmed E. coli on Petrifilm™ EC plates and on mFC agar were statistically not different (P=0.126) with a correlation coefficient of 0.879. Specificity of Petrifilm™ EC plates and mFC agar was evaluated by comparing typical colony counts with confirmed counts. On mFC agar, counts for typical colonies were by 2 log₁₀ CFU higher than the actual confirmed counts. In contrast, on Petrifilm™ EC plates typical colony counts were almost identical to confirmed colony counts for both fecal coliforms and E. coli. This comparison illustrates the high specificity of Petrifilm™ EC plates for enumeration of both fecal coliforms and E. coli in water.     

An over expression and high efficient mutation system of a cobalt-containing nitrile hydratase

A superior novel recombinant strain, E. coli BL21(DE3)/pETNH^M, containing the start codon mutation of the subunit, was constructed and selected as an overexpression and high efficient mutation platform for the genetic manipulation of the nitrile hydratase (NHase). Under optimal conditions, the specific activity of the recombinant strain reached as high as 452 U/mg dry cell. Enzymatic characteristics studies showed that the reaction activation energy of the recombinant NHase^M was 24.4 ± 0.5 kJ/mol, the suited pH range for catalysis was 5.5–7.5, and the K_m value was 4.34 g/L (82 mM). To assess the feasibility of the NHase improvement by protein rational design using this E. coli, site-directed mutagenesis of S122A, S122C, S122D and βW47E of the NHase^M were carried out. The NHase^M (S122A) and NHase^M (S122D) mutants were entirely inactive due to the charge change of the side-chain group. The product tolerance of the NHase^M (S122C) mutant was enhanced while its activity decreased by 30%. The thermo-stability of the NHase^M (βW47E) mutant was significantly strengthened, while its activity reduced by nearly 50%. These results confirmed that the specific activity of the mutant NHase expressed by the recombinant E. coli BL21(DE3)/pETNH^M can reasonably change with and without mutations. Therefore, this recombinant E. coli can be efficiently and confidently used for the further rational/random evolution of the NHase to simultaneously improve the activity, thermo-stability and product tolerance of the target NHase.     

Surface display of a glucose binding protein

Glucose binding protein (GBP) from Escherichia coli has been widely used to develop minimally invasive glucose biosensors for diabetics. To develop a cell-based glucose biosensor, it is essential to functionally display GBP on the cell surface. In this study, we designed a molecular structure to display GBP on the outer membrane of E. coli. We fused GBP with the first nine N-terminal residues of Lpp (major E. coli lipoprotein) and the 46–150 residues of OmpA (an outer membrane protein of E. coli). With this molecular design, we have successfully displayed GBP on the surface of E. coli. Using FITC-conjugated Dextran, we demonstrated that glucose’s binding sites of surface-displayed GBP were accessible to glucose. Furthermore, we showed that glucose transport in a GBP-deficient E. coli NM303 could be restored by displaying GBP on the surface of NM303. 0.51 h⁻¹ of specific growth rate was attained for NM303/pESDG grown in M9 minimal medium supplemented with 2 g/l glucose, whereas no growth was observed for NM303 in the same medium. Both NM303 and NM303/pESDG grew in M9 medium supplemented with 1 mM of fucose. Because cell surface is an interface between intracellular and extracellular molecular events, this technique paves a way to develop cell-based glucose biosensors.     

Simultaneous expression of glutaryl-7-aminocephalosporanic acid acylase gene and lysis genes of phage λ in a recombinant E. coli

Glutaryl-7-aminocephalosporanic acid acylase (GLA), recommended for use in the form of immobilized-enzyme, is one of the two key enzymes in the two-step synthesis of 7-aminocephalosporanic acid. For simplifying the process of cell disruption and immobilization, the lysis genes of phage λ (S⁻RRz) with the S amber mutation were designed to introduce into the over-expression system of GLA. A novel recombinant strain, E. coli TB1/pMKC-AS, simultaneously containing the maltose binding protein gene (malE), the lysis genes (S⁻RRz) and the target GLA gene (Acy) in a same operon, was successfully constructed. Under neutral pH conditions, cell growth and GLA activity of TB1/pMKC-AS was not affected by the presence of the lysis genes, however, autolysis phenomenon was observed under weak alkaline conditions. Through pH control and fed-batch culture, the GLA activity of TB1/pMKC-AS reached as high as 6810 U/L with 24.8 g/L dry cell density (OD₆₀₀ = 67.9) in a 5 L fermentor. In contrast to the cells of E. coli TB1/pMKC-Acy without the lysis genes, the mild EDTA/Tris buffer (pH 8.0) can cause the lysis of the cells of TB1/pMKC-AS containing the lysis genes. Correspondingly, a mild pH 9.0/42 °C incubation method was developed for conveniently degrading the recombinant cells of TB1/pMKC-AS, based on the expression of the lysis genes. Further experiments showed that the cell lysate after the mild incubation disruption can be directly immobilized by 10% polyacrylamide to make the immobilized enzymes. In comparison with the immobilized GLA from TB1/pMKC-Acy, the immobilized cell lysate of TB1/pMKC-AS has the similar characteristics of catalysis stability, implying a great potential for industrial application of the lysis genes-assisted cell disruption.     

Evaluation of 5'-nuclease and hybridization probe assays for the detection of shiga toxin-producing Escherichia coli in human stools

5′-Nuclease and a hybridization probe assays for the detection of shiga toxin-producing Escherichia coli were validated with regard to selectivity, analytical sensitivity, reproducibility and clinical performance. Both assays were capable of detecting the classical stx₁ and stx₂ genes when challenged with reference strains of E. coli (n = 40), although 1 to 4 minority sequence variants, whose clinical relevance is limited (stx_1c, stx_1d, and stx_2f), were detected less efficiently or not at all by one or both assays. No cross reaction was observed for both assays with 37 strains representing other gastrointestinal pathogens, or normal gastrointestinal flora. Analytical sensitivity ranged from 3.07 to 3.52 log₁₀ and 3.42 to 4.63 log₁₀ CFU/g of stool for 5′-nuclease and hybridization probe assay, respectively. Reproducibility was high with coefficients of variation of ≤ 5% for both inter- and intra-assay variation. Clinical performance was identical with a panel of archived positive specimens (n = 19) and a prospective panel of stools associated with bloody diarrhea (n = 115). In conclusion, both assays proved to be sensitive and reproducible.     

Optimization of bio-indigo production by recombinant E. coli harboring fmo gene

A bacterial flavin-containing monooxygenase (FMO) gene was cloned from Methylophaga aminisulfidivorans MP^T, and a plasmid pBlue 2.0 was constructed to express the bacterial fmo gene in E. coli. To increase the production of bio-indigo, upstream sequence size of fmo gene was optimized and response surface methodology was used. The pBlue 1.7 plasmid (1686 bp) was prepared by the deletion of upstream sequence of pBlue 2.0. The recombinant E. coli harboring the pBlue 1.7 plasmid produced 662 mg l⁻¹ of bio-indigo in tryptophan medium after 24 h of cultivation in flask. The production of bio-indigo was optimized using a response surface methodology with a 2ⁿ central composite design. The optimal combination of media constituents for the maximum production of bio-indigo was determined as tryptophan 2.4 g l⁻¹, yeast extract 4.5 g l⁻¹ and sodium chloride 11.4 g l⁻¹. In addition, the optimum culture temperature and pH were 30 °C and pH 7.0, respectively. Under the optimized conditions mentioned above, the recombinant E. coli harboring pBlue 1.7 plasmid produced 920 mg of bio-indigo per liter in optimum tryptophan medium after 24 h of cultivation in fermentor. The combination of truncated insert sizes and culture optimization resulted in a 575% increase in the production of bio-indigo.     

Lysozyme for capture of microorganisms on protein biochips

Lysozyme placed on the SiO₂ surfaces that have previously been derivatized with C₁₈ coating will capture both Escherichia coli and Listeria monocytogenes cells from PBS buffer at pH 7.2. This phenomenon is of significance for the design and fabrication of protein biochips that are designed to capture bacteria from buffer or water so that these can be further interrogated with respect to possible pathogenicity. Fluorescent microscopy shows that two types of bacteria (gram-negative E. coli and gram-positive Listeria spp.) will be adsorbed by lysozyme placed on the surface of the biochip but that strong adsorption of the bacteria is reduced but not eliminated when Tween 20 is present (at 0.5%) in the PBS buffer in which the cells are suspended. In comparison, Tween 20 and Bovine Serum Albumin (BSA) almost completely block adsorption of these bacteria on C₁₈ coated surfaces. The combination of a lysozyme surface with Tween 20 gives a greater degree of adsorption of L. monocytogenes than E. coli, and hence suggests selectivity for the more hydrophobic E. coli may be reduced by the Tween 20. This paper presents protocols for preparing protein-coated, SiO₂ surfaces and the effect of buffer containing Tween 20 on adsorption of bacteria by SiO₂ surfaces coated with C₁₈ to which BSA, lysozyme or C11E9 antibody is immobilized at pH 7.2 and ambient temperature.     

Isarfelin, a peptide with antifungal and insecticidal activities from Isaria felina

Isarfelin, a peptide with inhibitory activity on mycelial growth in Rhizoctonia solani and Sclerotinia sclerotiorum and insecticidal activity toward Leucania separata, was isolated from the mycelia of Isaria felina. The IC₅₀ value of its antifungal activity against R. solani was 3.1 μg mL⁻¹. However, it was devoid of activity toward several bacterial species including Bacillus subtilis, E. coli and Staphylococcus aureus. The isolation procedure involved ethanol extraction, adsorption on YPR II macropore adsorption resin, ethyl acetate extraction, petroleum ether precipitation and recrystallization from ethyl acetate.     

Thermostable glutamate dehydrogenase from a commensal thermophile, Symbiobacterium toebii; overproduction, characterization, and application

A gene encoding glutamate dehydrogenase (GDH) was found in the genome sequence of a commensal thermophile, Symbiobacterium toebii. The amino acid sequence deduced from the gdh I of S. toebii was well conserved with other thermostable GDHs. The gdh I which encodes GDH consisting of 409 amino acids was cloned and expressed in E. coli DH5 under the control of a highly constitutive expression (HCE) promoter in a pHCE system. The recombinant GDH was expressed without addition of any inducers in a soluble form. The molecular mass of the GDH was estimated to be 263 kDa by Superose 6 HR gel filtration chromatography and 44 kDa by sodium dodecyl sulfate-polyacrylamide gel electrophoresis (SDS-PAGE) indicating that the GDH was composed of hexameric form. The optimal temperature and pH of the purified enzyme were 60 °C and 9.0, respectively, and the purified GDH retained more than 75% of its original activity after an incubation at 70 °C for 30 min. Although NADP(H) was the preferred cofactor, S. toebii GDH was able to utilize either NADP(H) or NAD(H) as coenzyme.     

Effects of geometry on transmission and sensing potential of tapered fiber sensors

Geometry of tapered fiber sensors critically affects the response of an evanescent field sensor to cell suspensions. Single-mode fibers (nominally at 1300 nm) were tapered to symmetric or asymmetric tapers with diameters in the range of 3–20 μm, and overall lengths of 1–7 mm. Their transmission characteristics in air, water and in the presence of Escherichia coli (JM101 strain) at concentrations of 100, 1000, 7000 and 7 million cells/mL were measured in the 400–800 nm range and gave rich spectral data that lead to the following conclusions. (1) No change in transmission was observed due to E. coli with tapers that showed no relative change in transmission in water compared to air. (2) Tapers that exhibited a significant difference in transmission in water compared to air gave weak response to the presence of the E. coli. Of these, tapers with low waist diameters (6 μm) showed sensitivity to E. coli at 7000 cells/mL and higher concentration. (3) Tapers that showed modest difference in water transmission compared to air, and those that had small waist diameters gave excellent response to E. coli at 100–7000 cells/mL. In addition, mathematical modeling showed that: (1) at low wavelength (470 nm) and small waist diameter (6 μm), transmission with water in the waist region is higher than in air. (2) Small changes in waist diameter (0.05 μm) can cause larger changes in transmission at 470 nm than at 550 nm at waist diameter of 6 μm. (3) For the same overall geometry, a 5.5 μm diameter taper showed larger refractive index sensitivity compared to a 6.25 μm taper at 470 nm.     

Characterization of reactions catalysed by yeast phosphatidylinositol synthase

The nature of reactions catalysed by yeast phosphatidylinositol synthase expressed in E. coli has been investigated. The single enzyme is shown to carry both CDP-diacylglycerol-dependent incorporation of inositol into phosphatidylinositol (K_m for inositol of 0.090 mM) and a CDP-diacylglycerol-independent exchange reaction between phosphatidylinositol and inositol (K_m for inositol of 0.066 mM). The exchange reaction and reversal of phosphatidylinositol synthase were both stimulated by CMP, but had different optimum pH and requirements for substrates. These results suggest that CMP-stimulated exchange and CMP-dependent reverse reactions are distinct processes catalysed by the same enzyme. phosphatidylinositol synthase.     

Role of Hydroxyl Radicals in Escherzchza Colz Killing Induced by Hydrogen Peroxide

Escherichia coli lethality by hydrogen peroxide is characterized by two modes of killing. In this paper we have found that hydroxyl radicals (OH -) generated by H₂O₂ and intracellular divalent iron are not involved in the induction of mode one lethality (i.e. cell killing produced by concentrations of H₂O₂ lower than 2.5 mM). In fact, the OH radical scavengers, thiourea, ethanol and dimethyl sulfoxide, and the iron chelator, desferrioxarnine, did not affect the survival of cells exposed to 2.5mM H₂O₂. In addition cell vulnerability to the same H₂O₂ concentration was independent on the intracellular iron content. In contrast, mode two lethality (i.e. cell killing generated by concentrations of H₂O₂ higher than 10mM) was markedly reduced by OH radical scavengers and desferrioxamine and was augmented by increasing the intracellular iron content.

It is concluded that OH. are required for mode two killing of E. coli by hydrogen peroxide.     

Catalytic domain of Salmonella typhimurium 2-oxoglutarate dehydrogenase is localized in N-terminal region

2-Oxoglutarate dehydrogenase (lipoamide) [OGDH or E1o: 2-oxoglutarate: lipoamide 2-oxidoreductase (decarboxylating and acceptor-succinating); EC 1.2.4.2] is a component enzyme of the 2-oxoglutarate dehydrogenase complex. Salmonella typhimurium gene encoding OGDH (ogdh) has been cloned in Escherichia coli. The libraries were screened for the expression of OGDH by complementing the gene in E. coli E1o-deficient mutant. Three positive clones (named Odh-3, Odh-5 and Odh-7) contained the identical 2.9 kb Sau3AI fragment as determined by restriction mapping and Southern hybridization, and expressed OGDH efficiently and constitutively using its own promoter in the heterologous host. This gene spans 2878 bases and contains an open reading frame of 2802 nucleotides encoding a mature protein of 927 amino acid residues (M_r=110,000). The comparison of the deduced amino acid sequence of the cloned OGDH with E. coli OGDH shows 91% sequence identity. To localize the catalytic domain responsible for E. coli E1o-complementation, several deletion mutants lacking each portion of the ogdh gene were constructed using restriction enzymes. From the sodium dodecyl sulfate-polyacrylamide gel electrophoresis (SDS-PAGE) analysis, a polypeptide which showed a complementation activity with an M_r of 30,000 was detected. The catalytic domain was localized in N-terminal region of the gene. Therefore, this is a first identification of the catalytic domain in bacterial ogdh gene.     

The Sulfolobus tokodaii gene ST1704 codes highly thermostable glucose dehydrogenase

NAD(P)-dependent glucose-1-dehydrogenase (GDH) has been used for glucose determination and NAD(P)H production in bioreactors. Thermostable glucose dehydrogenase exhibits potential advantage for its application in biological processes. The function of the putative GDH gene (ST1704, 360-encoding amino acids) annotated from the total genome analysis of a thermoacidophilic archeaon Sulfolobus tokodaii strain 7 was investigated to develop more effective application of GDH. The gene encoding S. tokodaii GDH was cloned and the activity was expressed in Escherichia coli, which did not originally possess GDH. This shows that the gene (ST1704) codes the sequence of GDH. The enzyme was effectively purified from the recombinant E. coli with three steps containing a heat treatment and two successive chromatographies. The native enzyme (molecular mass: 160 kDa) is composed of a tetrameric structure with a type of subunit (41 kDa). The enzyme utilized both NAD and NADP as the coenzyme. The maximum activity for glucose oxidation in the presence of NAD was observed around pH 9 and 75 °C in the presence of 20 mM Mg²⁺. The enzyme showed broad substrate specificity: several monosaccarides such as 6-deoxy- -glucose, 2-amino-2-deoxy- -glucose and -xylose were oxidized as well as -glucose as the electron donor. -Mannose, -ribose and glucose-6-phosphate were inert as the donor. The enzyme showed high thermostability: remarkable loss of activity was not observed up to 80 °C by incubation for 15 min at pH 8.0. In addition, the enzyme was stable in a wide pH range of 5.0–10.5 by incubation at 37 °C. From the steady-state kinetic analysis, the enzyme reaction of -glucose oxidation proceeds via a sequential ordered Bi–Bi mechanism: NAD and -glucose bind to the enzyme in this order and then -glucono-1,5-lactone and NADH are released from the enzyme in this order. The amino acid sequence alignment showed that S. tokodaii GDH exhibited high homology with the Sulfolobus solfataricus hypothetical glucose dehydrogenase and a Thermoplasma acidophilum one.     

Enantioselective microbial reduction of 6-oxo-8-[4-[4-(2-pyrimidinyl)-1-piperazinyl]butyl]-8-azaspiro[4.5]decane-7,9-dione: Cloning and expression of reductases

The enantioselective microbial reduction of 6-oxo-8-[4-[4-(2-pyrimidinyl)-1-piperazinyl]butyl]-8-azaspiro[4.5]decane-7,9-dione (1) to either of the corresponding (S)- and (R)-6-hydroxy-8-[4-[4-(2-pyrimidinyl)-1-piperazinyl]butyl]-8-azaspiro[4.5]decane-7,9-diones (2 and 3, respectively) is described. The NADP⁺-dependent (R)-reductase (RHBR) which catalyzes the reduction of 6-ketobuspirone (1) to (R)-6-hydroxybuspirone (3) was purified to homogeneity from cell extracts of Hansenula polymorpha SC 13845. The subunit molecular weight of the enzyme is 35,000 kDa based on sodium dodecyl sulfate gel electrophoresis and the molecular weight of the enzyme is 37,000 kDa as estimated by gel filtration chromatography. (R)-reductase from H. polymorpha was cloned and expressed in Escherichia coli. To regenerate the cofactor NADPH required for reduction we have cloned and expressed the glucose-6-phosphate dehydrogenase gene from Saccharomyces cerevisiae in E. coli. The NAD⁺-dependent (S)-reductase (SHBR) which catalyzes the reduction of 6-ketobuspirone (1) to (S)-6-hydroxybuspirone (2) was purified to homogeneity from cell extracts of Pseudomonas putida SC 16269. The subunit molecular weight of the enzyme is 25,000 kDa based on sodium dodecyl sulfate gel electrophoresis. The (S)-reductase from P. putida was cloned and expressed in E. coli. To regenerate the cofactor NADH required for reduction we have cloned and expressed the formate dehydrogenase gene from Pichia pastoris in E. coli. Recombinant E. coli expressing (S)-reductase and (R)-reductase catalyzed the reduction of 1 to (S)-6-hyroxybuspirone (2) and (R)-6-hyroxybuspirone (3), respectively, in >98% yield and >99.9% e.e.     

Ferredoxin reductase enhances heterologously expressed cytochrome CYP105D1 in Escherichia coli and Streptomyces lividans

The ability of two different ferredoxin reductases from Streptomyces coelicolor, to enhance the amount of active recombinant Streptomyces griseus soyC (CYP105D1) was investigated in both Escherichia coli and Streptomyces lividans. In E. coli a two-plasmid system and a single operon construct were used for expression of the CYP105D1 and the ferredoxin reductase(s) under the control of T7 promoters. Expression levels of CYP105D1 were found to range between 85 and 280 nmol l⁻¹ cell culture after prolonged growth. In S. lividans the CYP105D1 and its ferredoxin were cloned downstream of the Pact1 promoter in the E. coli/Streptomyces shuttle vector pBW160. The recombinant E. coli and S. lividans cells converted 7-ethoxycoumarin into 7-hydroxycoumarin efficiently. Expression of a ferredoxin reductase as an operon with CYP105D1 and its ferredoxin enhances the o-dealkylation of 7-ethoxycoumarin. Ferredoxin NADPH reductase was found to enhance the level of the active form of CYP105D1 monooxygenase when no substrate was present.     

Methionine analogues as inhibitors of methionyl-tRNA synthetase

A series of methionine analogues have been synthesized as inhibitors of methionyl-tRNA synthetase and evaluated for their inhibitory activities of E. coli methionyl-tRNA synthetase and bacterial growth. Among them, -methionine hydroxamate 20 has proved to be the best inhibitor of the enzyme with K_i = 19 μM and showed a growth inhibition against E.coli JM 109, P. vulganis 6059 and C. freundii 8090.     

基于转录物组学的大肠杆菌血红素过氧化物酶EfeB的生理功能解析

大肠杆菌血红素过氧化物酶EfeB属于染料脱色过氧化物酶超家族。该家族的酶类一般具有良好的合成染料降解能力,但是其在生物体内的功能尚不清楚。为了深入研究EfeB的生理功能,本文通过同源重组的方法构建了efeB敲除菌株Eco△efeB,比较了亲本菌株E.coli BL21和Eco△efeB在基因组转录水平上、不同条件下的细胞生长以及对铁离子应答上的差异。结果表明:efeB基因的缺失引起了菌体1 765个基因的差异表达,这些基因主要与菌体的细胞代谢途径、细胞膜合成和鞭毛运动有关;在pH为7.0时,BL21和EcoΔefeB的生长无显著差异,但在pH4.5时BL21的生长明显优于EcoΔefeB,efeB基因的功能性表达可以支持大肠杆菌在低pH下的生存;当培养环境中有Fe²⁺存在时,efeB显著上调。以上结果为EfeB生理功能的认知和利用提供了一定的理论依据。     

Glyoxyl agarose as a new chromatographic matrix

At alkaline pHs, glyoxyl agarose is able to immobilize most of the proteins contained in a crude extract. However, due to its special immobilization features, at pH 7.0 only proteins that contain at least two exposed low pK amino groups in the same plane were immobilized (β-galactosidase from Escherichia coli, catalase from bovine liver, and IgG from rabbit). However, with many other proteins, even multimeric ones, immobilization could not be achieved (e.g.: glucose oxidase from Aspergillus niger and Penicillium vitale; catalase from Micococcus sp., A. niger and bovine liver; alcohol oxidase from Pichia pastoris, Hansenula sp. and Candida boidinii, β-galactosidase from Thermus sp., etc.). Elution of the attached proteins under mild conditions was not simple, if the number of protein-support bonds was very high, only boiling in SDS allowed the elution of the proteins. However, using glyoxyl agarose 4BCL with only 20 μmol of aldheyde groups/g of support, proteins could be fully eluted by competition with amino compounds (e.g., Tris buffer). In this first approach, we have tried to take advantage of this specific immobilization at pH 7.0 to purify multimeric proteins, using a β-galactosidase from E. coli as a model. The enzyme could be eluted from the support using Tris–HCl buffer as eluting agent, with a high yield (80%) and a high purification factor (32).     

Purification and partial characterization of Cu, Zn containing superoxide dismutase from entomogenous fungal species Cordyceps militaris

Cordyceps militaris mycelium produced mainly Cu, Zn containing superoxide dismutase (Cu, Zn-SOD). Cu, Zn-SOD activity was detectable in the culture filtrates, and intracellular Cu, Zn-SOD activity as a proportion protein was highest in early log phase culture. The effects of Cu²⁺, Zn²⁺, Mn²⁺ and Fe²⁺ on enzyme biosynthesis were studied. The Cu, Zn-SOD was isolated and purified to homogeneity from C. militaris mycelium and partially characterized. The purification was performed through four steps: (NH₄)₂SO₄ precipitation, DEAE-sepharose™ fast flow anion-exchange chromatography, CM-650 cation-exchange chromatography, and Sephadex G-100 gel filtration chromatography. The purified enzyme had a molecular weight of 35070 ± 400 Da and consisted of two equal-sized subunits each having a Cu and Zn element. Isoelectric point value of 7.0 was obtained for the purified enzyme. The N-terminal amino acid sequence of the purified enzyme was determined for 12 amino acid residues and the sequences was compared with other Cu, Zn-SODs. The optimum pH of the purified enzyme was obtained to be 8.2–8.8. The purified enzyme remained stable at pH 5.8–9.8, 25 °C and up to 50 °C at pH 7.8 for 1.5 h incubation. The purified enzyme was sensitive to H₂O₂, KCN. 2.5 mM NaN₃, PMSF, Triton X-100, β-mercaptoethanol and DTT showed no significant inhibition effect on the purified enzyme within 5 h incubation period.