Covalent immobilization of acetylcholinesterase on a novel polyacrylic acid‐based nanofiber membrane

In this study, polyacrylic acid‐based nanofiber (NF) membrane was prepared via electrospinning method. Acetylcholinesterase (AChE) from Electrophorus electricus was covalently immobilized onto polyacrylic acid‐based NF membrane by demonstrating efficient enzyme immobilization, and immobilization capacity of polymer membranes was found to be 0.4 mg/g. The novel NF membrane was synthesized via thermally activated surface reconstruction, and activation with carbonyldiimidazole upon electrospinning. The morphology of the polyacrylic acid‐based membrane was investigated by scanning electron microscopy, Fourier Transform Infrared Spectroscopy, and thermogravimetric analysis. The effect of temperature and pH on enzyme activity was investigated and maxima activities for free and immobilized enzyme were observed at 30 and 35°C, and pH 7.4 and 8.0, respectively. The effect of 1 mM Mn²⁺, Ni²⁺, Cu²⁺, Zn²⁺, Mg²⁺, Ca²⁺ ions on the stability of the immobilized AChE was also investigated. According to the Michaelis–Menten plot, AChE possessed a lower affinity to acetylthiocholine iodide after immobilization, and the Michaelis–Menten constant of immobilized and free AChE were found to be 0.5008 and 0.4733 mM, respectively. The immobilized AChE demonstrated satisfactory reusability, and even after 10 consecutive activity assay runs, AChE maintained ca. 87% of its initial activity. Free enzyme lost its activity completely within 60 days, while the immobilized enzyme retained approximately 70% of the initial activity under the same storage time. The favorable reusability of immobilized AChE enables the support to be employable to develop the AChE‐based biosensors.     

Adsorption of peroxidase on Celite 545 directly from ammonium sulfate fractionated white radish (Raphanus sativus) proteins

This paper demonstrates the direct immobilization of peroxidase from ammonium sulfate fractionated white radish proteins on an inorganic support, Celite 545. The adsorbed peroxidase was crosslinked by using glutaraldehyde. The activity yield for white radish peroxidase was adsorbed on Celite 545 was 70% and this activity was decreased and remained 60% of the initial activity after crosslinking by glutaraldehyde. The pH and temperature-optima for both soluble and immobilized peroxidase was at pH 5.5 and 40°C. Immobilized peroxidase retained higher stability against heat and water-miscible organic solvents. In the presence of 5.0 mM mercuric chloride, immobilized white radish peroxidase retained 41% of its initial activity while the free enzyme lost 93% activity. Soluble enzyme lost 61% of its initial activity while immobilized peroxidase retained 86% of the original activity when exposed to 0.02 mM sodium azide for 1 h. The K_m values were 0.056 and 0.07 mM for free and immobilized enzyme, respectively. Immobilized white radish peroxidase exhibited lower V_max as compared to the soluble enzyme. Immobilized peroxidase preparation showed better storage stability as compared to its soluble counterpart.     

Electrospun polyvinyl alcohol/bovine serum albumin biocomposite membranes for horseradish peroxidase immobilization

Electrospinning, a simple and versatile method to fabricate nanofibrous supports, has attracted attention in the field of enzyme immobilization. Biocomposite nanofibers were fabricated from mixed PVA/BSA solution and the effects of glutaraldehyde treatment, initial BSA concentration and PVA concentration on protein loading were investigated. Glutaraldehyde cross-linking significantly decreased protein release from nanofibers and BSA loading reached as high as 27.3% (w/w). In comparison with the HRP immobilized into the nascent nanofibrous membrane, a significant increase was observed in the activity retention of the enzyme immobilized into the PVA/BSA biocomposite nanofibers. The immobilized HRP was able to tolerate much higher concentrations of hydrogen peroxide than the free enzyme and thus the immobilized enzyme did not demonstrate substrate inhibition. The immobilized HRP retained ⿼50% of the free enzyme activity at 6.4 mM hydrogen peroxide and no significant variation was observed in the KM value of the enzyme for hydrogen peroxide after immobilization. In addition, reusability tests showed that the residual activity of the immobilized HRP were 73% after 11 reuse cycles. Together, these results demonstrate efficient immobilization of HRP into electrospun PVA/BSA biocomposite nanofibers and provide a promising immobilization strategy for biotechnological applications.     

Polyelectrolyte complex formation mediated immobilization of chitosan-invertase neoglycoconjugate on pectin-coated chitin

Saccharomyces cerevisiae invertase, chemically modified with chitosan, was immobilized on pectin-coated chitin support via polyelectrolyte complex formation. The yield of immobilized enzyme protein was determined as 85% and the immobilized biocatalyst retained 97% of the initial chitosan-invertase activity. The optimum temperature for invertase was increased by 10 °C and its thermostability was enhanced by about 10 °C after immobilization. The immobilized enzyme was stable against incubation in high ionic strength solutions and was 4-fold more resistant to thermal treatment at 65 °C than the native counterpart. The biocatalyst prepared retained 96 and 95% of the original catalytic activity after ten cycles of reuse and 74 h of continuous operational regime in a packed bed reactor, respectively.     

Immobilization of endo-polygalacturonase from Aspergillus ustus on silica gel

Endo-polygalacturonase from Aspergillus ustus when immobilized on to modified silica gel retained 28% of its original activity. The immobilized enzyme could be re-used through 10 cycles of reaction with almost 90% retention of its original activity. It had increased thermostability over its soluble form: the half-life of the soluble enzyme at 40 °C was less than 10 h whereas the immobilized enzyme retained 82% of its activity after 10 h at 40 °C. Similarly, at 50 °C the half-life of the soluble enzyme was 30 min whereas that of the immobilized enzyme was 5 h.     

Silanized palygorskite for lipase immobilization

Lipase from Candida lipolytica has been immobilized on 3-aminopropyltriethoxysilane-modified palygorskite support. Scanning electron micrographs proved the covalently immobilization of C. lipolytica lipase on the palygorskite support through glutaraldehyde. Using an optimized immobilization protocol, a high activity of 3300 U/g immobilized lipase was obtained. Immobilized lipase retained activity over wider ranges of temperature and pH than those of the free enzyme. The optimum pH of the immobilized lipase was at pH 7.0–8.0, while the optimum pH of free lipase was at 7.0. The retained activity of the immobilized enzyme was improved both at lower and higher pH in comparison to the free enzyme. The immobilized enzyme retained more than 70% activity at 40 °C, while the free enzyme retained only 30% activity. The immobilization stabilized the enzyme with 81% retention of activity after 10 weeks at 30 °C whereas most of the free enzyme was inactive after a week. The immobilized enzyme retains high activity after eight cycles. The kinetic constants of the immobilized and free lipase were also determined. The K_m and V_max values of immobilized lipase were 0.0117 mg/ml and 4.51 μmol/(mg min), respectively.     

Immobilization of glucose oxidase on Fe<Subscript>3</Subscript>O<Subscript>4</Subscript>/SiO<Subscript>2</Subscript> magnetic nanoparticles

Glucose oxidase (GOD) was covalently immobilized onto Fe₃O₄/SiO₂ magnetic nanoparticles (FSMNs) using glutaraldehyde (GA). Optimal immobilization was at pH 6 with 3-aminopropyltriethoxysilane at 2% (v/v), GA at 3% (v/v) and 0.143 g GOD per g carrier. The activity of immobilized GOD was 4,570 U/g at pH 7 and 50°C. The immobilized GOD retained 80% of its initial activity after 6 h at 45°C while free enzyme retained only 20% activity. The immobilized GOD maintained 60% of its initial activity after 6 cycles of repeated use and retained 75% of its initial activity after 1 month at 4°C whereas free enzymes retained 62% of its activity.     

Acetylcholinesterase with mesoporous silica: Covalent immobilization,physiochemical characterization,and its application in food for pesticide detection

Toxic contamination of commonly consumed food products and water due to food chain vulnerability via agricultural products and commodities is a serious health hazard. This study reports on Santa Barbara Amorphous (SBA-15), a type of mesoporous silica nanoparticles, for efficient and stable acetylcholinesterase (AChE) adhesion toward detection of toxic pesticides. AChE was immobilized to the inert framework of mesoporous materials viz. SBA-15 with a proficient hydrolytic response toward acetylthiocholine. The immobilized system acts as a biosensor for the detection of pesticides, which are organophosphorus compounds in food. Both the SBA-15 and immobilized SBA-15 were characterized to give an insight on the physiochemical and morphological modification properties. The enzyme activity was accessed by Ellman’s spectrophotometric bioassay for bare and enzyme-immobilized SBA-15 that resulted in promising enzymatic activity with the counterpart. Enzyme stability was also studied, which exhibited that immobilized AChE retained its catalytic activity up to 60 days and retained 80% of the hydrolytic activity even at 37°C. On the basis of the success of immobilized enzyme (covalent) being inhibited by acetylthiocholine, the sensor was administered for the inhibition by monocrotophos and dimethoate that are used widely as pesticides in agricultural. The inhibitory concentration (IC₅₀) value was found to be 2.5 ppb for monocrotophos and 1.5 ppb for dimethoate inhibiting immobilized AChE. This was verified using cyclic voltammetry, an electrochemical analysis thus proving that the SBA-15@AChE complex could be used as a sensitive and highly stable sensor for detecting the concentration of hazardous pesticide compounds.     

Immobilization of goat brain aminopeptidase B in calcium alginate beads

Aminopeptidase B, an arginyl aminopeptidase, was purified from goat brain with a purification factor of ～280 and a yield of 2.7%. It was entrapped in calcium alginate together with bovine serum albumin. The optimal conditions for immobilization for maximum activity yield were 1% CaCl₂ and 2.5% alginate. The immobilized enzyme retained ～62% of its initial activity and could be used for five successive batch reactions with retention of 30% of the initial activity. The pH and temperature optima of the free and immobilized enzyme were pH 7.4, 45°C and pH 7.8, 50°C respectively, while the pH and thermal stability as well as the stability of the enzyme in organic solvents were improved significantly after entrapment. The K_m value for the immobilized enzyme was about twofold higher than that of the soluble enzyme. Because of this increased stability, the immobilized enzyme may be useful in the meat processing industry.     

The potential of immobilized bacterial α-amylase on coconut coir,a smart carrier for biocatalysts

Purified α-amylase from a soil bacterium Bacillus sp. SKB4 was immobilized on coconut coir, an inexpensive cellulosic fiber, with the cross-linking agent glutaraldehyde. The catalytic properties and stability of the immobilized enzyme were compared with those of its soluble form. The enzyme retained 97.2% of its activity and its catalytic properties were not drastically altered after immobilization. The pH optimum and stability of the immobilized enzyme were shifted towards the alkaline range compared to the free enzyme. The optimum temperature for enzymatic activity was 90°C in both forms of the enzyme. The soluble and immobilized enzyme retained 19% and 70% of original activity, respectively, after pre-incubation for 1 h at 90°C. Immobilized amylase was less susceptible to attack by heavy metal ions and showed higher K_m and V_max values than its free form. The bound enzyme showed significant activity and stability after 6 months of storage at 4°C. All of these characteristics make the new carrier system suitable for use in the bioprocess and food industries.     

A new method for immobilization of acetylcholinesterase

A new method for immobilization of acetylcholinesterase (AChE) to alginate gel beads by activating the carbonyl groups of alginate using carbodiimide coupling agent has been successfully developed. Maximum reaction rate (V _max) and Michaelis–Menten constant (K _m) were determined for the free and binary immobilized enzyme. The effects of pH, temperature, storage stability, reuse number and thermal stability on the free and immobilized AChE were also investigated. For the free and binary immobilized enzyme on the Ca–alginate gel beads, optimum pH values were found to be 7 and 8, respectively. Optimum temperatures for the free and immobilized enzyme were observed to be 30 and 35 °C, respectively. Upon 60 days of storage the preserved activity of free and immobilized enzyme were found as 4 and 68%, respectively. In addition, reuse number, and thermal stability of the free AChE were increased by as a result of binary immobilization.     

Immobilization of levan fructotransferase for the production of di-fructose anhydride from levan

Levan fructotransferase (LFTase) from Arthrobacter ureafaciens K2032 was immobilized on various carriers of which Chitopearl BCW2501 beads showed the higher activity of 320 U g^–1 for the formation of di-fructose anhydride compounds. The immobilized enzyme retained about 60% of its initial activity after being used for 20 cycles.     

Immobilization of chitosan-invertase neoglycoconjugate on carboxymethylcellulose-modified chitin

Saccharomyces cerevisiae invertase, chemically modified with chitosan, was immobilized on a carboxymethylcellulose-coated chitin support via polyelectrolyte complex formation. The yield of immobilized protein was determined to be 72% and the enzyme retained 68% of the initial invertase activity. The optimum temperature for invertase was increased by 5 degrees C and its thermostability was enhanced by about 9 degrees C after immobilization. The immobilized enzyme was stable against incubation in high ionic strength solutions and was 12.6-fold more resistant to thermal treatment at 65 degrees C than the native counterpart. The prepared biocatalyst retained 98% and 100% of the original catalytic activity after 10 cycles of reuse and 70 h of continuous operational regime in a packed bed reactor, respectively. The immobilized enzyme retained 95% of its activity after 50 days of storage at 37 degrees C.     

Covalent immobilization of ω-transaminase from Vibrio fluvialis JS17 on chitosan beads

Chitosan beads were prepared by emulsion method and used for the immobilization of ω-transaminase of Vibrio fluvialis. The yield of enzyme immobilization (54.3%) and its residual activity (17.8%) were higher than those obtained with other commercial beads. ω-Transaminase was effectively immobilized on the chitosan beads at pH 6.0. The optimal pH of the immobilized enzyme was pH 9.0, which is the same as that of the free enzyme. The immobilized enzyme on chitosan beads retained ca. 77% of its conversion after five consecutive reactions with the 25 mM substrate, while the immobilized enzyme on Eupergit^® C retained 12%. Also, the immobilized ω-transaminase on chitosan bead retained 70% of initial activity when it's stored at 4 °C for 3.5 weeks. Addition of the co-factor, pyridoxal 5-phosphate (PLP), was needed to maintain the stability of the immobilized ω-transaminase.     

Electrospun polyacrylonitrile nanofibrous membranes for lipase immobilization

Polyacrylonitrile (PAN) nanofibers could be fabricated by electrospinning with fiber diameter in the range of 150–300 nm, providing huge surface area for enzyme immobilization and catalytic reactions. Lipase from Candida rugosa was covalently immobilized onto PAN nanofibers by amidination reaction. Aggregates of enzyme molecules were found on nanofiber surface from field emission scanning electron microscopy and covalent bond formation between enzyme molecule and the nanofiber was confirmed from FTIR measurements. After 5 min activation and 60 min reaction with enzyme-containing solution, the protein loading efficiency was quantitative and the activity retention of the immobilized lipase was 81% that of free enzyme. The mechanical strength of the NFM improved after lipase immobilization where tensile stress at break and Young's modulus were almost doubled. The immobilized lipase retained >95% of its initial activity when stored in buffer at 30 °C for 20 days, whereas free lipase lost 80% of its initial activity. The immobilized lipase still retained 70% of its specific activity after 10 repeated batches of reaction. This lipase immobilization method shows the best performance among various immobilized lipase systems using the same source of lipase and substrate when considering protein loading, activity retention, and kinetic parameters.     

Purification, immobilization and characterization of linoleic acid isomerase on modified palygorskite

Linoleic acid isomerase from Lactobacillus delbrueckii subsp. bulgaricus 1.1480 was purified by DEAE ion-exchange chromatography and gel filtration chromatography. An overall 5.1% yield and purification of 93-fold were obtained. The molecular weight of the purified protein was ~41 kDa which was analyzed by SDS-PAGE. The purified enzyme was immobilized on palygorskite modified with 3-aminopropyltriethoxysilane. The immobilized enzyme showed an activity of 82 U/g. The optimal temperature and pH for the activity of the free enzyme were 30 °C and pH 6.5, respectively; whereas those for the immobilized enzyme were 35 °C and pH 7.0, respectively. The immobilized enzyme was more stable than the free enzyme at 30–60 °C, and the operational stability result showed that more than 85% of its initial activity was retained after incubation for 3 h. The K _m and V _max values of the immobilized enzyme were found to be 0.0619 mmol l⁻¹ and 0.147 mmol h⁻¹ mg⁻¹, respectively. The immobilized enzyme had high operational stability and retained high enzymatic activity after seven cycles of reuse at 37 °C.     

Thermo-sensitive amphiphilic block copolymer poly (styrene-<Emphasis Type="Italic">b</Emphasis>-N-isopropylacrylamide) with switchable catalytic activity immobilizing pectinase

Pectinase was immobilized onto thermo-sensitive amphiphilic block copolymers poly(styrene-b-Nisopropylacrylamide) PS-b-poly(N-isopropylacrylamide) (PNIPAM) by covalent attachment. Biochemical studies have found that the stability of the PS-b-PNIPAM support is not impeded by the bound proteins despite that up to 242.5 mg of enzyme is immobilized per gram of carrier particles. The immobilized enzyme retained nearly 65% of its initial activity over 30 days, and the optimum temperature and pH also increased to the range of 60 ∼ 70°C and 4.0 ∼ 6.0, respectively. The immobilized enzyme also exhibited great operational stability, and more than 60% residual activity was observed in the immobilized enzyme after 10 batch reactions. Moreover, the lower critical solution temperature of the PS-b-PNIPAM support could be switched on or off by a small change in solution temperature. Thus, the immobilized pectinase could be recovered and showed durable activity during the recycle process.     

Optimization of covalent immobilization of pectinase on sodium alginate support

Pectinase was immobilized on a sodium alginate support using glutaraldehyde and retained 66% activity. The optimal pH for activity shifted from 3.0 to 3.5 after immobilization; however, the optimum temperature remained unchanged at 40°C. The immobilized enzyme also had a higher thermal stability and reusability than the free enzyme, and retained 80% of initial activity after 11 batch reactions.     

Calcium alginate–starch hybrid support for both surface immobilization and entrapment of bitter gourd (Momordica charantia) peroxidase

Calcium alginate–starch hybrid gel was employed as an enzyme carrier both for surface immobilization and entrapment of bitter gourd peroxidase. Entrapped crosslinked concanavalin A–bitter gourd peroxidase retained 52% of the initial activity while surface immobilized and glutaraldehyde crosslinked enzyme showed 63% activity. A comparative stability of both forms of immobilized bitter gourd peroxidase was investigated against pH, temperature and chaotropic agent; like urea, heavy metals, water-miscible organic solvents, detergent and inhibitors. Entrapped peroxidase was significantly more stable as compared to surface immobilized form of enzyme. The pH and temperature-optima for both immobilized preparations were the same as for soluble bitter gourd peroxidase. Entrapped crosslinked concanavalin A–bitter gourd peroxidase showed 75% of the initial activity while the surface immobilized and crosslinked bitter gourd peroxidase retained 69% of the original activity after its seventh repeated use.     

Catalytic properties of the immobilized Aspergillus tamarii xylanase

Xylanase from Aspergillus tamarii was covalently immobilized on Duolite A147 pretreated with the bifunctional agent glutaraldehyde. The bound enzyme retained 54.2% of the original specific activity exhibited by the free enzyme (120 U/mg protein). Compared to the free enzyme, the immobilized enzyme exhibited lower optimum pH, higher optimum reaction temperature, lower energy of activation, higher K_m (Michaelis constant), lower V_max (maximal reaction rate). The half-life for the free enzyme was 186.0, 93.0, and 50.0 min for 40, 50, and 60°C, respectively, whereas the immobilized form at the same temperatures had half-life of 320, 136, and 65 min. The deactivation rate constant at 60°C for the immobilized enzyme is about 6.0 × 10⁻³, which is lower than that of the free enzyme (7.77 × 10⁻³ min). The energy of thermal deactivation was 15.22 and 20.72 kcal/mol, respectively for the free and immobilized enzyme, confirming stabilization by immobilization. An external mass transfer resistance was identified with the immobilization carrier (Duolite A147). The effect of some metal ions on the activity of the free and immobilized xylanase has been investigated. The immobilized enzyme retained about 73.0% of the initial catalytic activity even after being used 8 cycles.