Highly selective ratiometric fluorescent Zn2+ chemosensor based on diarylethene derivative with bi‐8‐carboxamidoquinoline unit

An asymmetrical diarylethene (1O) with a bi‐8‐carboxamidoquinoline unit was synthesized. Its photochromic and fluorescence performances on stimulation with both light and metal ions showed that the diarylethene could serve as a highly selective ratiometric fluorescent chemosensor to detect Zn²⁺ ions based on internal charge transfer and chelation‐enhanced fluorescence processes. The diarylethene could selectively discriminate Zn²⁺ from Cd²⁺ in acetonitrile. Furthermore, Job's plots based on fluorescence titration and electrospray ionization mass spectrometry analysis showed 1 : 1 binding stoichiometry between 1O and Zn²⁺. The binding constant of 1O with Zn²⁺, estimated using the Benesi–Hildebrand method, and the limit of detection were 3.37 × 10⁵ M^–1 and 4.6 × 10^–8 mol/L, respectively. Additionally, the light and metal‐responsive fluorescence behavior of 1O was used successfully to construct a molecular logic circuit with four inputs and one output. Copyright © 2016 John Wiley & Sons, Ltd.     

A new quaternary photoluminescence enhancement system of Eu−N‐(o‐vanillin)‐1,8‐diaminonaphthalene−1,10‐phenanthroline−Zn and its application in determining trace amounts of europium and zinc

A new sensitive quaternary photoluminescence enhancement system has been successfully developed to determine trace amounts of Eu³⁺ and Zn²⁺. The photoluminescence intensity of Eu ? N‐(o‐vanilin)‐1,8‐diaminonaphthalene systems was greatly increased by the addition of specific concentrations of 1, 10‐phenanthroline and Zn²⁺. The excitation and emission wavelengths were 274 and 617 nm, respectively. Under optimal system conditions, the photoluminescence intensity showed a linear response toward Eu³⁺ in the range of 5.0 × 10^–6 ~ 2.0 × 10^–5 M with a limit of detection (= 2.2 × 10^–9 M) and the photoluminescence intensity of the system decreased linearly by increasing the Zn²⁺ concentration in the range of 5.0 × 10^–8 ~ 1.0 × 10^–6 M with a limit of detection (= 8.8 × 10^–11 M). This system was successfully applied for the determination of trace amounts of Eu³⁺ in a high purity La₂O₃ matrix and in the synthetic rare earth oxide mixture, and of Zn²⁺ in a high purity Mg(NO₃)₂ · 6H₂O matrix and in synthetic coexisting ionic matrixes. The energy transfer mechanism, photoluminescence enhancement of the system and interference of other lanthanide ions and common coexisting ions were also studied in detail. Copyright © 2013 John Wiley & Sons, Ltd.     

Phenothiazine–rhodamine‐based colorimetric and fluorogenic ‘turn‐on' sensor for Zn2+ and bioimaging studies in live cells

A phenothiazine–rhodamine (PTRH) fluorescent dyad was synthesized and its ability to selectively sense Zn²⁺ ions in solution and in in vitro cell lines was tested using various techniques. When compared with other competing metal ions, the PTRH probe showed the high selectivity for Zn²⁺ ions that was supported by electronic and emission spectral analyses. The emission band at 528 nm for the PTRH probe indicated the ring closed form of PTRH, as for Zn²⁺ ion binding to PTRH, the λ_em get shift to 608 nm was accompanied by a pale yellow to pink colour (under visible light) and green to pinkish red fluorescence emission (under UV light) due to ring opening of the spirolactam moiety in the PTRH ligand. Spectral overlap of the donor emission band and the absorption band of the ring opened form of the acceptor moiety contributed towards the fluorescence resonance energy transfer ON mechanism for Zn²⁺ ion detection. The PTRH sensor had the lowest detection limit for Zn²⁺, found to be 2.89 × 10^?8 M. The sensor also demonstrated good sensing application with minimum toxicity for in vitro analyses using HeLa cells.     

Characterization of a highly Al3+‐selective fluorescence probe based on naphthalimide‐Schiff base and its application to practical water samples

A new fluorescent Al³⁺‐probe, N‐allyl‐4‐[3,3′‐((2‐aminoethyl)azanediyl)‐bis(N´‐(2‐hydroxybenzylidene)propanehy‐drazide)]‐1,8‐naphthalimide ( L ), was designed and synthesized based on 1,8‐naphthalimide. The probe L contains 1,8‐naphthalimide moiety as the fluorophore and a Schiff base as the recognition group. The structure of L was determined by single crystal X‐ray. L emission at 526 nm increased on addition of Al³⁺ under excitation wavelength at 350 nm. L exhibited high selectivity and sensitivity fluorescence emission towards to Al³⁺ in ethanol/Tris–HCl buffer solution (1:1, v/v, pH = 7.2) as compared with other tested metal ions. A good linearity with a correlation coefficient (R²) of 0.99 was observed in the concentration range 2–10 μM. The binding constant and the detection limit of L for Al³⁺ were calculated to 2.6 × 10⁴ M^?1 and 0.34 μM, respectively. The results of experiments that including Job plot, ultraviolet–visible (UV–Vis) light titration, fluorescence titration, ESI‐MS and ¹H NMR titration, indicated a 1:1 stoichiometric complex between L and Al³⁺. L was highly effective in monitoring Al³⁺ in real‐life Yellow River and tap water samples.     

Light emission from the Fe2+–EDTA–ascorbic acid–H2O2 system strongly enhanced by plant phenolic acids

Oxidative reactions can result in the formation of electronically excited species that undergo radiative decay depending on electronic transition from the excited state to the ground state with subsequent ultra‐weak photon emission (UPE). We investigated the UPE from the Fe²⁺–EDTA (ethylenediaminetetraacetic acid)–AA (ascorbic acid)–H₂O₂ (hydrogen peroxide) system with a multitube luminometer (Peltier‐cooled photon counter, spectral range 380–630 nm). The UPE, of 92.6 μmol/L Fe²⁺, 185.2 μmol/L EDTA, 472 μmol/L AA, 2.6 mmol/L H₂O₂, reached 1217 ± 118 relative light units during 2 min measurement and was about two times higher (P < 0.001) than the UPE of incomplete systems (Fe²⁺–AA–H₂O₂, Fe²⁺–EDTA–H₂O₂, AA–H₂O₂) and medium alone. Substitution of Fe²⁺ with Cr²⁺, Co²⁺, Mn²⁺ or Cu²⁺ as well as of EDTA with EGTA (ethylene glycol‐bis(β‐aminoethyl ether)‐N,N,N′,N′‐tetraacetic acid) or citrate powerfully inhibited UPE. Experiments with scavengers of reactive oxygen species (dimethyl sulfoxide, mannitol, sodium azide, superoxide dismutase) revealed the dependence of UPE only on hydroxyl radicals. Dimethyl sulfoxide at the concentration of 0.74 mmol/L inhibited UPE by 79 ± 4%. Plant phenolics (ferulic, chlorogenic and caffec acids) at the concentration of 870 μmol/L strongly enhanced UPE by 5‐, 13.9‐ and 46.8‐times (P < 0.001), respectively. It is suggested that augmentation of UPE from Fe²⁺–EDTA–AA–H₂O₂ system can be applied for detection of these phytochemicals.     

A carbonothioate‐based highly selective fluorescent probe with a large Stokes shift for detection of Hg2+

Mercury (Hg) is one of the heavy metal pollutants in the environment. Even a very small amount of mercury can cause serious harm to human beings. Herein, we reported a new carbonothioate‐based fluorescent probe for the detection of Hg²⁺ without interference from other metal ions. This probe possessed a very large Stokes shift (192 nm), which could improve the detection sensitivity by minimizing the interferences resulted from self‐absorption or auto‐fluorescence. With the addition of Hg²⁺ to the probe solution, considerable fluorescence enhancement was observed. Additionally, the Hg²⁺ concentration of 0–16 μM and fluorescence intensity showed a good linear relationship (y = 22106× + 53108, R² = 0.9955). Finally, the proposed probe was used to detect Hg²⁺ in real water samples, and its result was satisfactory. Therefore, our proposed probe would provide a promising method for the determination of Hg²⁺ in the environment.     

Enantiomeric assay of escitalopram S(+)‐enantiomer and its “in‐process impurities” using two different techniques

The enantiomeric purity of escitalopram oxalate ESC and its “in‐process impurities,” namely, ESC‐N‐oxide, ESC‐citadiol, and R(?)‐enantiomer were studied in drug substance and products using high‐performance liquid chromatography (HPLC)‐UV (Method I), synchronous fluorescence spectroscopy (SFS) (Method IIA), and first derivative SFS (Method IIB). Method I describes as an isocratic HPLC‐UV for the direct resolution and determination of enantiomeric purity of ESC and its “in‐process impurities.” The proposed method involved the use of α_l‐acid glycoprotein (AGP) chiral stationary phase. The regression plots revealed good linear relationships of concentration range of 0.25 to 100 and 0.25 to 10 μg mL^?1 for ESC and its impurities. The limits of detection and quantifications for ESC were 0.075 and 0.235 μg mL^?1, respectively. Method II involves the significant enhancement of the fluorescence intensities of ESC and its impurities through inclusion complexes formation with hydroxyl propyl‐β‐cyclodextrin as a chiral selector in Micliavain buffer. Method IIA describes SFS technique for assay of ESC at 225 nm in presence of its impurities: R(?)‐enantiomer, citadiol, and N‐oxide at ?λ of 100 nm. This method was extended to (Method IIB) to apply first derivative SFS for the simultaneous determination of ESC at 236 nm and its impurities: the R(?)‐enantiomer, citadiol, and N‐oxide at 308, 275, and 280 nm, respectively. Linearity ranges were found to be 0.01 to 1.0 μg mL^?1 for ESC and its impurities with lower detection and quantification limits of 0.033/0.011 and 0.038/0.013 μg mL^?1 for SFS and first derivative synchronous fluorescence spectra (FDSFS), respectively. The methods were used to investigate the enantiomeric purity of escitalopram.     

A selective and sensitive fluorescent sensor for cysteine detection based on bi‐8‐carboxamidoquinoline derivative and Cu2+ complex

In this paper, a novel fluorescent sensor 1 for selective and sensitive detection of cysteine was developed based on a complex between bi‐8‐carboxamidoquinoline derivative ligand ( L ) and Cu²⁺. The interaction of Cu²⁺ with the ligand causes a dramatic fluorescence quenching most likely due to its high affinity towards Cu²⁺ and a ligand–metal charge transfer (LMCT) process. The in situ generated L–Cu ² complex was utilized as a chemosensing ensemble for cysteine. In the presence of cysteine, the fluorophore, L , was released from L–Cu ² complex because of the strong affinity of cysteine to Cu²⁺ via the Cu–S bond, leading to the fluorescence recovery of the ligand. The proposed displacement mechanism was confirmed by the results of mass spectrometry (MS) study. Under optimized conditions, the recovered fluorescence intensity is linear with cysteine concentrations in the range 1 × 10^?6 mol/l to 8 × 10^?6 mol/l. The detection limit for cysteine is 1.92 × 10^?7 mol/l. Furthermore, the established method showed a highly sensitive and selective response to cysteine among the 20 fundamental α‐amino acids used as the building blocks of proteins, after Ni²⁺ was used as a masking agent to eliminate the interference of His. The proposed sensor is applicable in monitoring cysteine in practical samples with good recovery rate.     

Polymer composite fluorescent hydrogel film based on nitrogen‐doped carbon dots and their application in the detection of Hg2+ ions

A simple microwave‐assisted solvothermal method was used to prepare fluorescent nitrogen‐doped carbon dots (N‐CDs) with high fluorescence quantum yield (79.63%) using citric acid and N‐(2‐hydroxyethyl)ethylenediamine as starting materials. The PVAm‐g‐N‐CDs grafted products were synthesized by amide bond formation between the carboxylic groups of N‐CDs and amine groups of polyvinylamine (PVAm). Fluorescent hydrogel films (PVAm‐g‐N‐CDs/PAM) were synthesized by interpenetration polymer network polymerization of PVAm‐g‐N‐CDs and acrylamide (AM). When used for ion detection, we found that the fluorescence of the hydrogel films was clearly quenched by addition of Hg²⁺. Repeatability tests on using the hydrogel films for Hg²⁺ detection showed that they could be applied at least three times. The PVAm‐g‐N‐CDs/PAM could serve as an effective fluorescent sensing platform for sensitive detection of Hg²⁺ ions with a detection limit of 0.089 μmol/L. This work may offer a new approach for developing recoverable and sensitive N‐CDs‐based sensors for biological and environmental applications.     

Novel fluorescent sensor using molecularly imprinted silica microsphere‐coated CdSe@CdS quantum dots and its application in the detection of 2,4,6‐trichlorophenol from environmental water samples

In this study, a high fluorescence sensitivity and selectivity, molecularly imprinted nanofluorescent polymer sensor (MIP@SiO₂@QDs) was prepared using a reverse microemulsion method. 2,4,6‐Trichlorophenol (2,4,6‐TCP) was detected using fluorescence quenching. Tetraethyl orthosilicate (TEOS), quantum dots (QDs) and 3‐aminopropyltriethoxysilane (APTS) were used as cross‐linker, signal sources and functional monomer respectively. The sensor (MIP@SiO₂@QDs) and the non‐imprinted polymer sensor (NIP@SiO₂@QDs) were characterized using infra‐red (IR) analysis, X‐ray diffraction (XRD), transmission electron microscopy (TEM) and scanning electron microscopy (SEM). The selectivity of MIP@SiO₂@QDs was examined by comparing 2,4,6‐TCP with other similar functional substances including 2,4‐dichlorophenol (2,4‐DCP), 2,6‐dichlorophenol (2,6‐DCP) and 4‐chlorophenol (4‐CP). Results showed that MIP@SiO₂@QDs had better selectivity for 2,4,6‐TCP than the other compounds. Fluorescence quenching efficiency displayed a good linear response at the 2,4,6‐TCP concentration range 5–1000 μmol/L. The limit of detection (LOD) was 0.9 μmol/L (3σ, n = 9). This method was equally applicable for testing actual samples with a recovery rate of 98.0–105.8%. The sensor had advantages of simple pretreatment, good sensitivity and selectivity, and wide linear range and could be applied for the rapid detection of 2,4,6‐TCP in actual samples.     

Construction of a novel turn‐on–off fluorescence sensor used for highly selective detection of thiamine via its quenching effect on o‐phen‐Zn2+ complex

In this work, a simple and selective fluorescence sensor approach called ‘turn‐on–off’ for the determination of thiamine (TM) has been developed. As known, the o‐phenanthroline (o‐phen) has inner fluorescence, though when reacted with zinc ions to form the o‐phen–Zn²⁺ complex the fluorescence intensity was enhanced effectively, while upon addition of TM into the o‐phen–Zn²⁺ complex solution, the intensity of the system was gently quenched, which was termed the ‘turn‐on–off’ probe. Notably, the method possessed highly selective, sensitive determination for TM with a detection limit of 0.25 μmol L^?1 and the reduced fluorescence intensity was proportional to the concentration of TM in the range 0.84–80.0 μmol L^?1. Besides, the proposed mechanism was also investigated through exploring the Fourier transform infrared (FT‐IR), nuclear magnetic resonance (NMR) spectroscopy. Furthermore, this manner was successfully applied into practical samples for TM detection with satisfactory results.     

Luminescent sensor for Cd2+, Hg2+ and Ag+ in water based on a sulphur‐containing receptor: quantitative binding–softness relationship

A water‐soluble, high‐output fluorescent sensor, based on a lumazine ligand with a thiophene substituent for Cd²⁺, Hg²⁺ and Ag⁺ metal ions, is reported. The sensor displays fluorescence enhancement upon Cd²⁺ binding (log  β = 2.79 ± 0.08) and fluorescence quenching by chelating with Ag⁺ and Hg²⁺ (log β = 4.31 ± 0.15 and 5.42 ± 0.1, respectively). The mechanism of quenching is static and occurs by formation of a ground‐state non‐fluorescent complex followed by rapid intersystem crossing. The value of the Stern–Volmer quenching rate constant (k_q) by Ag⁺ ions is close to 6.71 × 10¹² mol/L/s at 298 K. The thermodynamic parameters (ΔG, ΔH and ΔS) were also evaluated and indicated that the complexation process is spontaneous, exothermic and entropically favourable. The quantitative linear relationship between the softness values of Klopman (σ_K) or Ahrland (σ_A) and the experimental binding constants (β) being in the order of Hg²⁺ > Ag⁺ > Cd²⁺ suggests that soft–soft interactions are the key for the observed sensitivity and selectivity in the presence of other metal ions, such as: Pb²⁺, Ni²⁺, Mn²⁺, Cu²⁺, Co²⁺, Zn²⁺ and Mg²⁺ ions. Copyright © 2008 John Wiley & Sons, Ltd.     

Multimode selective detection of mercury by chiroptical fluorescent sensors based on methionine/cysteine

Two multimode Hg(II) sensors, L‐MethBQA and L‐CysBQA, were obtained by fusing methionine or S‐methyl cysteine, into a bis‐quinolyl amine‐based chiral podand scaffold. Quinolyl groups serve as the fluorophore and possess nitrogen lone pairs capable of chelating metal ions. On exposure to Hg²⁺ or Zn²⁺, these sensors show signal enhancement in fluorescence. However, Cu²⁺ quenches their fluorescence in 30:70 acetontrile/water. L‐CysBQA complexes with Hg²⁺, producing an exciton‐coupled circular dichroism spectrum with the opposite sign to the one that is produced by Cu²⁺ or Zn²⁺ complexation. L‐CysBQA binds Hg²⁺ more strongly than Zn²⁺ and is shown to differentiate Hg²⁺ from other metal ions, such as Zn²⁺, Cu²⁺, Ni²⁺, and Pb²⁺, exceptionally well. The synergistic use of relatively soft sulfur, quinoline‐based chiral ligands and chiroptically enhanced fluorescence detection results in high sensitivity and selectivity for Hg²⁺. Chirality, 2011. © 2011 Wiley‐Liss, Inc.     

Quantification of three triterpenic acids in dried rosemary using HPLC‐fluorescence detection and 4‐(4,5‐diphenyl‐1H‐imidazole‐2‐yl)benzoyl chloride derivatization

Functional triterpenic acids such as ursolic acid (UA), oleanolic acid (OA) and betulinic acid (BA) are representative ingredients in rosemary that may have health benefits. UA, OA and BA in rosemary extracts were derivatized with 4‐(4,5‐diphenyl‐1H‐imidazole‐2‐yl)benzoyl chloride (DIB‐Cl) and detected using HPLC‐fluorescence (FL). Dried rosemary (50 mg) was ground, added to 3 ml of ethanol, sonicated for 40 min, then the sample solution was added to a mixture of 1% trimethylamine and 1 mM DIB‐Cl in acetonitrile. The mixture was settled for 5 min at room temperature, then the DIB‐triterpenic acid derivatives were separated using a Wakopak Handy ODS column (250 × 4.6 mm, 6 μm) eluted with 25 mM acetate buffer (pH 4.5)/methanol/acetonitrile (= 8:10:82 v/v/v%). The fluorescence intensity of the eluent was monitored at 365 (λ_ex) and 490 nm (λ_em) and the maximum retention time of the derivatives was 30 min. Calibration curves constructed using rosemary extract spiked with standards showed good linearity (r ≥ 0.997) in the range 2.5–100 ng/ml. The detection limits at 3σ for internal BA, UA and OA peaks in rosemary extract were 0.2, 0.4 and 0.5 ng/ml, respectively. This method was used to quantify BA, UA and OA in commercially available dried rosemary products.     

Ratiometric fluorescent detection of Cu2+ based on dual‐emission ZIF‐8@rhodamine‐B nanocomposites

Zeolitic imidazolate framework‐8 (ZIF‐8) loading rhodamine‐B (ZIF‐8@rhodamine‐B) nanocomposites was proposed and used as ratiometric fluorescent sensor to detect copper(II) ion (Cu²⁺). Scanning electron microscopy, Fourier transform infrared spectroscopy, X‐ray powder diffraction, nitrogen adsorption/desorption isotherms and fluorescence emission spectroscopy were employed to characterize the ZIF‐8@rhodamine‐B nanocomposites. The results showed the rhodamine‐B was successfully assembled on ZIF‐8 based on the π‐π interaction and the hydrogen bond between the nitrogen atom of ZIF‐8 and –COOH of rhodamine‐B. The as‐obtained ZIF‐8@rhodamine‐B nanocomposites were octahedron with size about 150–200 nm, had good water dispersion, and exhibited the characteristic fluorescence emission of ZIF‐8 at 335 nm and rhodamine‐B at 575 nm. The Cu²⁺ could quench fluorescence of ZIF‐8 rather than rhodamine‐B. The ZIF‐8 not only acted as the template to assemble rhodamine‐B, but also was employed as the signal fluorescence together with the fluorescence of rhodamine‐B as the reference to construct a novel ratiometric fluorescent sensor to detect Cu²⁺. The resulted ZIF‐8@rhodamine‐B nanocomposite fluorescence probe showed good linear range (68.4 nM to 125 μM) with a low detection limit (22.8 nM) for Cu²⁺ combined with good sensitivity and selectivity. The work also provides a better way to design ratiometric fluorescent sensors from ZIF‐8 and other fluorescent molecules.     

Flow‐injection method for the determination of iodide/iodine using Ru(bpy)33+–NADH chemiluminescence detection

A two‐channel flow‐injection (FI) method is reported for the determination of iodide and iodine by its enhancement effect on the Ru(bpy)₃³⁺–NADH chemiluminescence (CL) system. The limit of detection (3 s of blank) was 1.0 × 10^–9 mol/L iodide/iodine, with a sample throughput of 60/h. The calibration graphs over the range 1.0–50 × 10^–8 mol/L gave correlation coefficients of 0.9994 and 0.999 (n = 5) with relative standard deviations (RSD; n = 4) of 1.0–2.5%, respectively. The effects of interfering cations, anions and some organic compounds were also studied. The method was applied to iodized salts and pharmaceutical samples and the results obtained were in good agreement with the value quoted. The CL method developed was compared with spectrophotometric method. Copyright © 2008 John Wiley & Sons, Ltd.     

Chemiluminescence method for the determination of piroxicam by the enhancement of the tris‐(4,7‐diphenyl‐1,10‐phenanthrolinedisulphonic acid) ruthenium(II) (RuBPS)–cerium(IV) system and its application

A simple, rapid chemiluminescence (CL) method was described for the determination of piroxicam, a commonly used analgesic agent drug. A strong CL signal was detected when cerium(IV) sulphate was injected into tris‐(4,7‐diphenyl‐1,10‐phenanthrolinedisulphonic acid) ruthenium(II) (RuBPS)–piroxicam solution. The CL signal was proportional to the concentration of piroxicam in the range 2.8 × 10^–8–1.2 × 10^–5 mol/L. The detection limit was 2 × 10^–8 mol/L and the relative standard deviation (RSD) was 3.7% (c = 7.0 × 10^–7 mol/L piroxicam; n = 11). The proposed method was applied to the determination of piroxicam in pharmaceutical preparations in capsules, spiked serum and urine samples with satisfactory results. Copyright © 2008 John Wiley & Sons, Ltd.     

Purification of glucose‐6‐phosphate dehydrogenase from rat (Rattus norvegicus) erythrocytes and inhibition effects of some metal ions on enzyme activity

Glucose‐6‐phosphate dehydrogenase (G6PD) is the first enzyme on which the pentose phosphate pathway was checked. In this study, purification of a G6PD enzyme was carried out by using rat erythrocytes with a specific activity of 13.7 EU/mg and a yield of 67.7 and 155.6‐fold by using 2′,5′‐ADP Sepharose‐4B affinity column chromatography. For the purpose of identifying the purity of enzyme and molecular mass of the subunit, a sodium dodecyl sulfate‐polyacrylamide gel electrophoresis was carried out. The molecular mass of subunit was calculated 56.5 kDa approximately. Then, an investigation was carried out regarding the inhibitory effects caused by various metal ions (Fe²⁺, Pb²⁺, Cd²⁺, Ag⁺, and Zn²⁺) on G6PD enzyme activities, as per Beutler method at 340 nm under in vitro conditions. Lineweaver–Burk diagrams were used for estimation of the IC₅₀ and K_i values for the metals. K_i values for Pb⁺², Cd⁺², Ag⁺, and Zn⁺² were 113.3, 215.2, 19.4, and 474.7 μM, respectively.     

Hg2+‐selective ratiometric and colorimetric probe based on dansyl–rhodamine and its staining function in cell imaging

A new ratiometric probe composed of a dansyl–rhodamine dyad for the detection of Hg²⁺ via fluorescence resonance energy transfer was designed and synthesized. Rhodamine, dansyl chloride, and hydrazide were selected as the acceptor, donor, and reaction site, respectively. It displayed high selectivity and sensitivity to Hg²⁺ with obvious colour change and fluorescence change due to Hg²⁺‐assisted hydrolysis of rhodamine hydrazide. A good linear relationship ranging from 0 to 16 μM and 0–28 μM for the Hg²⁺ concentration was found based on absorbance and fluorescence assay, respectively. Detection limits of absorbance and fluorescence for Hg²⁺ were calculated to be 1.22 μM and 9.10 μM, respectively.     

Hydrothermal synthesis for high‐quality glutathione‐capped CdxZn1 – xSe and CdxZn1 – xSe/ZnS alloyed quantum dots and its application in Hg(II) sensing

High‐quality Cd_xZn_{1 – x}Se and Cd_xZn_{1 – x}Se/ZnS core/shell quantum dots (QDs) emitting in the violet–green spectral range have been successfully prepared using hydrothermal methods. The obtained aqueous Cd_xZn_{1 – x}Se and Cd_xZn_{1 – x}Se/ZnS QDs exhibit a tunable photoluminescence (PL) emission (from 433.5 nm to 501.2 nm) and a favorable narrow photoluminescence bandwidth [full width at half maximum (FWHM): 30–42 nm]. After coating with a ZnS shell, the quantum yield increases from 40.2% to 48.1%. These Cd_xZn_{1 – x}Se and Cd_xZn_{1 – x}Se/ZnS QDs were characterized by transmission electron microscopy, X‐ray diffraction, X‐ray photoelectron spectroscopy and Fourier transform infrared (FTIR) spectroscopy. To further understand the alloying mechanism, the growth kinetics of Cd_xZn_{1 – x}Se were investigated through measuring the fluorescence spectra and X‐ray diffraction spectra at different growth intervals. The results demonstrate that the inverted ZnSe/CdSe core/shell structure is formed initially after the injection of Cd²⁺. With further heating, the core/shell structured ZnSe/CdSe is transformed into alloyed Cd_xZn_{1 – x}Se QDs with the diffusion of Cd²⁺ into ZnSe matrices. With increasing the reaction temperature from 100 °C to 180 °C, the duration time of the alloying process decreases from 210 min to 20 min. In addition, the cytotoxicity of Cd_xZn_{1 – x}Se and Cd_xZn_{1 – x}Se/ZnS QDs were investigated. The results indicate that the as‐prepared Cd_xZn_{1 – x}Se/ZnS QDs have low cytotoxicity, which makes them a promising probe for cell imaging. Finally, the as‐prepared Cd_xZn_{1 – x}Se/ZnS QDs were utilized to ultrasensitively and selectively detect Hg²⁺ ions with a low detection limit (1.8 nM).