Anammox反应器启动过程中颗粒污泥性状变化特性

以厌氧颗粒污泥作为接种物,通过185 d的运行,成功启动了上流式厌氧氨氧化污泥床(Upflow anaerobic sludge blanket,UASB)反应器。反应器的进水氨氮与亚硝氮浓度分别提升至224 mg/L和255 mg/L,容积氮去除速率提升至3.76 kg/(m3·d)。采用红外光谱、扫描电镜和透射电镜等对厌氧氨氧化颗粒污泥的性状进行观察,发现颗粒污泥在启动过程中经历了污泥颗粒裂解到污泥颗粒重组的过程,且厌氧氨氧化颗粒污泥表面含有丰富的官能团,说明厌氧氨氧化颗粒污泥可能具有良好的吸附性能。采用宏基因组测序的方法对启动前后颗粒污泥的生态结构进行分析,发现原接种污泥优势菌群(变形菌门、厚壁菌门、拟杆菌门)丰度大幅减少,厌氧氨氧化菌所属的浮霉状菌门丰度则由1.59%提升到23.24%。     

中试厌氧氨氧化反应器的启动与调控

研究了中试厌氧氨氧化(Anaerobic ammonium oxidation,Anammox)反应器的启动性能。结果表明,以硝化反硝化污泥、短程硝化污泥、厌氧絮体污泥和厌氧颗粒污泥混合接种,经过255d的运行,可在常温下(5oC～27oC)成功启动中试Anammox反应器,反应器的基质氮去除速率可达1.30kg/(m3·d)。厌氧氨氧化是致碱反应,厌氧氨氧化成为反应器内的主导反应后,进水pH宜控制在厌氧氨氧化适宜范围的偏低水平(6.8左右)。亚硝酸盐既是Anammox菌的基质,也是抑制剂,控制进水亚硝酸盐浓度(13～36mg/L)有助于厌氧氨氧化反应。菌种是生物反应器的功能之源,向中试装置投加少量厌氧氨氧化污泥(投加比2%),可大大加速中试Anammox反应器的启动进程。     

气提式内循环硝化反应器运行性能的研究

气提式内循环反应器具有很好的生物硝化性能,能承受高进水氨浓度（78.49mmol/L）,具有高容积转化效率（163.18 mmol/L·d）,运行性能稳定（氨去除率保持在94.42%以上）。在气提式内循环反应器的运行过程中,可产生硝化颗粒污泥。颗粒污泥开始出现的时间约为45d,颗粒污泥的粒径平均值0.83 mm,沉降速度55.53m/h,氨氧化活性0.95mmol (NH⁺₄-N)/g(VS)·d。硝化颗粒污泥也具有厌氧氨氧化活性,氨氧化速率0.23mmol (NH⁺₄-N)/g(VS)·d,亚硝酸还原速率0.24mmol (NO^-₂-N)/g(VS)·d。     

厌氧氨氧化反应器的启动研究

目的：对UASB-生物膜反应器进行厌氧氨氧化反应的启动研究。方法：以自配含氨氮和亚硝氮的废水为进水,以氧化沟工艺城市污水处理厂回流污泥为接种污泥。结果：反应器内部菌群进行了竞争,在运行至第66d时氨氮、亚硝酸盐氮的去除率分别达到了60.4%、58.7%,同时有硝酸盐氮生成,表明厌氧氨氧化反应已经成为反应器内的主导反应。结论：厌氧氨氧化反应器实现了快速启动。     

流加菌种对厌氧氨氧化工艺的影响

厌氧氨氧化工艺具有很高的容积氮去除速率,现已成功应用于污泥压滤液等含氨废水的脱氮处理,容积氮去除速率高达9.5 kg/(m3·d)。但由于厌氧氨氧化菌为自养型细菌,生长缓慢,对环境条件敏感,致使厌氧氨氧化工艺启动时间过长,运行容易失稳,并且不适合处理有机含氨废水和毒性含氨废水,极大地限制了该工艺的进一步推广应用。为了克服厌氧氨氧化工艺实际应用中存在的问题,结合发酵工业中常用的菌种流加技术,提出了一种新型的菌种流加式厌氧氨氧化工艺,研究了该新型工艺在厌氧氨氧化工艺的启动过程、稳定运行以及处理有机含氨废水和毒性含氨废水等方面的应用情况。结果表明,通过向反应器内补加优质厌氧氨氧化菌种,可提高厌氧氨氧化菌数量及其在菌群中的比例,强化厌氧氨氧化功能。据此研发的菌种流加式厌氧氨氧化工艺不仅可以实现快速启动,而且可以稳定运行,并突破了有机物和毒物所致的运行障碍,拓展了厌氧氨氧化工艺的应用范围。     

三种接种物启动Anammox-EGSB反应器的性能

为了优选接种物和加速Anammox反应器启动,分别以厌氧产甲烷污泥 (Anaerobic methanogenic sludge,AMS)、新鲜厌氧氨氧化污泥 (Fresh Anammox sludge,FAS) 和储藏厌氧氨氧化污泥 (Stored Anammox sludge,SAS) 作为接种物,研究了厌氧氨氧化膨胀颗粒污泥床 (Anammox-EGSB) 反应器 (R1、R2和R3) 的启动性能。结果表明：3种接种物均能成功启动Anammox-EGSB反应器,启动性能的优劣次序为：R2 (接种物为     

生产性短程硝化-厌氧氨氧化装置处理制药废水的启动性能

为拓展新型生物脱氮技术的应用领域,研究了生产性短程硝化-厌氧氨氧化装置处理制药废水的启动性能。制药废水氨氮浓度为(430.40±55.43)mg/L时,氨氮去除率达(81.75±9.10)%,实现了短程硝化-厌氧氨氧化工艺对制药废水的生物脱氮。制药废水短程硝化系统的启动时间约为74 d,亚硝氮积累率达(52.11±9.13)%,证明了结合模拟废水和实际废水的"两步法"模式对短程硝化系统启动的适用性。制药废水厌氧氨氧化系统的启动时间约为145 d,最大容积氮去除速率达6.35 kg N/(m3·d),容积效能为传统硝化-反硝化工艺的数十倍,证明了结合菌种自繁和菌种流加的模式对厌氧氨氧化系统启动的适用性。     

短程硝化启动运行中功能菌群变化研究

【目的】短程硝化-厌氧氨氧化是可实现的最短生物脱氮工艺,短程硝化是实现该工艺的重要环节和必要条件。【方法】采用序批式反应器(SBR)来实现短程硝化过程的启动和稳定运行,并对该过程中的相关功能菌群变化进行检测分析。【结果】通过控制低DO浓度(<1 mg/L)和逐步提高氨氮进水负荷,可抑制氨氧化细菌(NOB)菌群增殖并促进亚硝酸氧化菌(AOB)菌群规模显著扩大,实现短程硝化过程的启动和稳定运行。在氨氮进水负荷为0.055 kg/(m3.d)时,平均氨氮去除容积负荷和污泥负荷可达到0.043kg/(m3.d)和0.16 kg/(kg.d),平均亚硝酸盐积累率可达到83.4%。在短程硝化启动和稳定运行过程中,NOB菌群密度从2.0×105CFU/mL降至1.5×104CFU/mL,相对丰度从5.51%降至2.14%;AOB菌群密度从4.5×104CFU/mL增加至1.5×107CFU/mL,相对丰度从0.18%增加至7.25%。【结论】AOB菌群规模的扩大是实现短程硝化和氨氮去除能力提高的主要原因,同时较高的进水氨氮浓度和负荷也会造成亚硝化活性的抑制。     

厌氧折流板反应器处理PTA废水及其相分离特性

对厌氧折流板反应器（ABR）处理精对苯二甲酸（IOTA）生产废水的启动及相分离过程进行研究。结果表明：经过62d的运行,反应器在（35±1）℃、水力停留时间40h、容积负荷3．60kg/（m3·d）的条件下,最大COD去除率达到80％以上,ABR启动成功。沿着水流方向,不同格室中挥发性脂肪酸（VFA）浓度依次减小,CH4含量不断增加,且污泥中挥发性悬浮固体浓度（VSS）及其与总悬浮固体浓度（弼）之比、产甲烷活性和辅酶F420不断增大,ABR中显示出显著的厌氧微生物相分离特性。     

同步厌氧生物脱氮除硫工艺性能的研究

研究了同步厌氧生物脱氮除硫工艺的性能。该工艺具有很高的硫化物和硝酸盐转化潜能,稳态运行时的容积硫化物去除率和容积硝酸盐去除率分别为3.73kg/(m3.d)和0.80kg/(m3.d);能够耐受580mg/L的硫化物浓度和110mg/L的硝酸盐浓度,适宜浓度分别为280mg/L和67.5mg/L;能够耐受较高的水力负荷,适宜的水力停留时间为0.13d,反应器运行性能会因缩短水力停留时间而突发性恶化。     

The development of simultaneous partial nitrification, ANAMMOX and denitrification (SNAD) process in a single reactor for nitrogen removal

The simultaneous partial nitrification, ANAMMOX and denitrification (SNAD) process was validated to potentially remove ammonium and COD from wastewater in a single, oxygen-limited, non-woven rotating biological contactor (NRBC) reactor. An ammonium conversion efficiency of 79%, TN removal efficiency of 70% and COD removal efficiency of 94% were obtained with the nitrogen and COD loading rate of 0.69 kgN/m(3)d and 0.34 kg/m(3)d, respectively. Scanning electron microscopy (SEM) observation and fluorescence in situ hybridizations (FISH) analysis revealed the existence of the dominant groups of bacteria. As a result, the aerobic ammonia-oxidizing bacteria (AOB), with a spot of aerobic heterotrophic bacteria were mainly distributed in the aerobic outer part of the biofilm. However, ANAMMOX bacteria with denitrifying bacteria were present and active in the anaerobic inner part of the SNAD biofilm. These bacteria were found to exist in a dynamic equilibrium to achieve simultaneous nitrogen and COD removal in NRBC system.     

Sensitivity analysis of a biofilm model describing a one-stage completely autotrophic nitrogen removal (CANON) process.

A mathematical model for nitrification and anaerobic ammonium oxidation (ANAMMOX) processes in a single biofilm reactor (CANON) was developed. This model describes completely autotrophic conversion of ammonium to dinitrogen gas. Aerobic ammonium and nitrite oxidation were modeled together with ANAMMOX. The sensitivity of kinetic constants and biofilm and process parameters to the process performance was evaluated, and the total effluent concentrations were, in general, found to be insensitive to affinity constants. Increasing the amount of biomass by either increasing biofilm thickness and density or decreasing porosity had no significant influence on the total effluent concentrations, provided that a minimum total biomass was present in the reactor. The ANAMMOX process always occurred in the depth of the biofilm provided that the oxygen concentration was limiting. The optimal dissolved oxygen concentration level at which the maximum nitrogen removal occurred is related to a certain ammonium surface load on the biofilm. An ammonium surface load of 2 g N/m2. d, associated with a dissolved oxygen concentration level of 1.3 g O2/m3 in the bulk liquid and with a minimum biofilm depth of 1 mm seems a proper design condition for the one-stage ammonium removal process. Under this condition, the ammonium removal efficiency is 94% (82% for the total nitrogen removal efficiency) (30 degrees C). Better ammonium removal could be achieved with an increase in the dissolved oxygen concentration level, but this would strongly limit the ANAMMOX process and decrease total nitrogen removal. It can be concluded that a one-stage process is probably not optimal if a good nitrogen effluent is required. A two-stage process like the combined SHARON and ANAMMOX process would be advised for complete nitrogen removal.     

Novel microbial nitrogen removal processes

The present-day wastewater treatment practices can be significantly improved through the introduction of new microbial treatment technologies. Recently, several new processes for nitrogen removal have been developed. These new nitrogen removal technologies provide practicable options for treating nitrogen-laden wastewaters. The new processes are based on partial nitrification of ammonium to nitrite combined with anaerobic ammonium oxidation. These processes include the single reactor system for high ammonia removal over nitrite (SHARON) process, which involves part conversion of ammonium to nitrite; the anaerobic ammonium oxidation (ANAMMOX) process, which involves anaerobic ammonium oxidation; and the completely autographic nitrogen removal over nitrite (CANON) process, which involves nitrogen removal within one reactor under oxygen-limited conditions. These new processes target the removal of nitrogen from wastewaters containing significant quantities of ammonium.     

Modeling a granule‐based anaerobic ammonium oxidizing (ANAMMOX) process

A mathematical model was developed to describe the anaerobic ammonium oxidation (ANAMMOX) process in a granular upflow anaerobic sludge blanket (UASB) reactor. ANAMMOX granules were cultivated in the UASB reactor by seeding aerobic granules. The granule‐based reactor had a great N‐loading resistant capacity. The model simulation results on the 1‐year reactor performance matched the experimental data well. The yield coefficient for the growth and the decay rate coefficient of the ANAMMOX granules were estimated to be 0.164 g COD g^?1 N and 0.00016 h^?1, respectively. With this model, the effects of process parameters on the reactor performance were evaluated. Results showed that the optimum granule diameter for the maximum N‐removal should be between 1.0 and 1.3 mm and that the optimum N loading rate should be 0.8 kg N m^?3 d^?1. In addition, the substrate micro‐profiles in the ANAMMOX granules were measured with a microelectrode to explore the diffusion dynamics within the granules, and the measured profiles matched the predicted results well. Biotechnol. Bioeng. 2009;103: 490–499. © 2009 Wiley Periodicals, Inc.     

Biological treatment of ammonium-rich wastewater by partial nitritation and subsequent anaerobic ammonium oxidation (anammox) in a pilot plant

In wastewater treatment plants with anaerobic sludge digestion, 15-20% of the nitrogen load is recirculated to the main stream with the return liquors from dewatering. Separate treatment of this ammonium-rich digester supernatant would significantly reduce the nitrogen load of the activated sludge system. Some years ago, a novel biological process was discovered in which ammonium is converted to nitrogen gas under anoxic conditions with nitrite as the electron acceptor (anaerobic ammonium oxidation, anammox). Compared to conventional nitrification and denitrification, the aeration and carbon-source demand is reduced by over 50 and 100%, respectively. The combination of partial nitritation to produce nitrite in a first step and subsequent anaerobic ammonium oxidation in a second reactor was successfully tested on a pilot scale (3.6 m(3)) for over half a year. This report focuses on the feasibility of nitrogen removal from digester effluents from two different wastewater treatment plants (WWTPs) with the combined partial nitritation/anammox process. Nitritation was performed in a continuously stirred tank reactor (V=2.0 m(3)) without sludge retention. Some 58% of the ammonium in the supernatant was converted to nitrite. At 30 degrees C the maximum dilution rate D(x) was 0.85 d(-1), resulting in nitrite production of 0.35 kg NO(2)-N m(-3)(reactor) d(-1). The nitrate production was marginal. The anaerobic ammonium oxidation was carried out in a sequencing batch reactor (SBR, V=1.6 m(3)) with a nitrogen elimination rate of 2.4 kg N m(-3)(reactor) d(-1) during the nitrite-containing periods of the SBR cycle. Over 90% of the inlet nitrogen load to the anammox reactor was removed and the sludge production was negligible. The nitritation efficiency of the first reactor limited the overall maximum rate of nitrogen elimination.     

Inactivation of ANAMMOX communities under concurrent operation of anaerobic ammonium oxidation (ANAMMOX) and denitrification

A concurrent operation of anaerobic ammonium oxidation (ANAMMOX) and denitrification was investigated in a well known UASB reactor seeding with both ANAMMOX and anaerobic granular sludges. ANAMMOX activity was confirmed by hydroxylamine test and the hybridization of biomass using the gene probes of Amx 820 and EUB 338 mixed. Denitrification was observed through the reductions of both COD and nitrate-nitrite concentrations under anaerobic/anoxic conditions. By providing a stoichiometric ratio of nitrite to ammonium nitrogen with addition nitrate nitrogen, a gradual reduction of ANAMMOX activity was found with an increase of COD concentration in a range of 100-400 mg l(-1). This is equivalent to the COD to N ratio of 0.9-2.0. The COD concentration was found to be a control variable for process selection between ANAMMOX reaction and denitrification. A reduction of COD and nitrite-nitrate concentrations in all reactors confirmed the undergone concurrent denitrification which thrives when sufficient organic matter is available. COD concentration over 300 mg l(-1) was found to inactivate or eradicate ANAMMOX communities.     

Anaerobic ammonium oxidation in constructed wetlands with bio-contact oxidation as pretreatment

Anaerobic ammonium oxidation (ANAMMOX) may provide an effective nitrogen removal pathway for constructed wetlands with low C/N influent. In a study of domestic sewage treatment, anaerobic ammonium oxidation process was identified in the pilot-scale constructed wetland of a bio-ecological process which was composed of a bio-contact oxidation reactor and a horizontal subsurface flow constructed wetland (CW). To investigate the ANAMMOX establishment in the bio-ecological process, two new CWs (planted and unplanted) were developed to be a control for the pre-existing CW. Under operational conditions of DO 2-3 mg/l, HRT 3.5 h for the bio-contact oxidation reactor, HRT 3 days for CWs, and domestic sewage as influent, the process achieved more than 90% TN removal rate after the ANAMMOX was established. The ANAMMOX bacteria on the media of the constructed wetlands were analyzed by specific polymerase chain reaction (PCR) with ANAMMOX specific primer set AMX818F-AMX1066R. The result of the genetic sequencing showed that the PCR product was related to Candidatus B. anammoxidans (AF375994.1) with 98% sequence similarity. Copy numbers of 16S rRNA gene of ANAMMOX bacteria in the pre-existing CW, the new planted CW and new unplanted CW were 3.47 × 10⁵, 3.02 × 10⁵ and 1.30 × 10⁵, respectively. These results demonstrated that the ANAMMOX process was successfully established and operated consistently in the constructed wetlands with a bio-contact oxidation reactor as a pretreatment, and that vegetation positively affected the growth and enrichment of ANAMMOX bacteria.     

厌氧氨氧化工艺的应用现状和问题

厌氧氨氧化(Anaerobic ammonium oxidation,ANAMMOX)工艺因其高效低耗的优势,在废水生物脱氮领域具有广阔的应用前景。在过去的20年中,许多基于ANAMMOX反应的工艺得以不断研究和应用。预计到2014年末,全球范围内的ANAMMOX工程将会超过100座。综述了各种形式的ANAMMOX工艺,包括短程硝化-厌氧氨氧化、全程自养脱氮、限氧自养硝化反硝化、反硝化氨氧化、好氧反氨化、同步短程硝化-厌氧氨氧化-反硝化耦合、单级厌氧氨氧化短程硝化脱氮工艺。对一体式和分体式工艺运行条件进行了比较,结合ANAMMOX工艺工程(主要包括移动床生物膜,颗粒污泥和序批式反应器系统)应用现状,总结了工程化应用过程中遇到的问题及其解决对策,在此基础上对今后的研究和应用方向进行了展望。今后的研究重点应集中于运行条件的优化和水质障碍因子的解决,尤其是工艺自动化控制系统的开发和特殊废水对工艺性能影响的研究。