Development of a solar-powered microbial fuel cell

Aims: To understand factors that impact solar‐powered electricity generation by Rhodobacter sphaeroides in a single‐chamber microbial fuel cell (MFC). Methods and Results: The MFC used submerged platinum‐coated carbon paper anodes and cathodes of the same material, in contact with atmospheric oxygen. Power was measured by monitoring voltage drop across an external resistance. Biohydrogen production and in situ hydrogen oxidation were identified as the main mechanisms for electron transfer to the MFC circuit. The nitrogen source affected MFC performance, with glutamate and nitrate‐enhancing power production over ammonium. Conclusions: Power generation depended on the nature of the nitrogen source and on the availability of light. With light, the maximum point power density was 790 mW m^?2 (2·9 W m^?3). In the dark, power output was less than 0·5 mW m^?2 (0·008 W m^?3). Also, sustainable electrochemical activity was possible in cultures that did not receive a nitrogen source. Significance and Impact of the Study: We show conditions at which solar energy can serve as an alternative energy source for MFC operation. Power densities obtained with these one‐chamber solar‐driven MFC were comparable with densities reported in nonphotosynthetic MFC and sustainable for longer times than with previous work on two‐chamber systems using photosynthetic bacteria.     

The impact of monochromatic blue and red LED light upon performance of photo microbial fuel cells (PMFCs) using Chlamydomonas reinhardtii transformation F5 as biocatalyst

Photosynthetic microbial fuel cells (PMFCs) are devices that convert chemical energy into the form of electricity through the catalytic activity of photosynthetic microorganisms. Power densities produced by the photosynthetic microalgae are greatly dependant on light sources and light intensities because these two factors can affect the chlorophyll formation, photosynthesis processes and stomata opening in the microalgae cells. In the present study, Chlamydomonas reinhardtii transformation F5 was used as biocatalyst in photo microbial fuel cells (PMFCs) and were illuminated with monochromatic blue and red LED lights at various light intensities (100, 300, 600 and 900 lx), respectively. The kinetic analysis was successfully employed to describe the intracellular and extracellular electron transfer mechanism of the cells. The results demonstrate that the performance of PMFCs increased in terms of maximum power density and exchange current density (i_o) with the tendency of decreasing in internal resistance (R_int) and over potential (η) values as increasing monochromatic blue and red LED light intensities. However the PMFCs performed better under red LED light as compared to operating under blue LED light. The maximum power density can reach 12.947 mW m⁻², which could be a potential micro-power supply.     

New exoelectrogen Citrobacter sp. SX-1 isolated from a microbial fuel cell

Aims: Isolation, identification and characterization of a new exoelectrogenic bacterium from a microbial fuel cell (MFC). Methods and Results: Exoelectrogenic bacterial strain SX‐1 was isolated from a mediator‐less MFC by conventional plating techniques with ferric citrate as electron acceptor under anaerobic condition. Phylogenetic analysis of the 16S rDNA sequence revealed that it was related to the members of Citrobacter genus with Citrobacter sp. sdy‐48 being the most closely related species. The bacterial strain SX‐1 produced electricity from citrate, acetate, glucose, sucrose, glycerol and lactose in MFCs with the highest current density of 205 mA m^?2 generated from citrate. Cyclic voltammetry analysis indicated that membrane‐associated proteins may play an important role in facilitating the electrons transferring from bacteria to electrode. Conclusions: This is the first study that demonstrates that Citrobacter species can transfer electrons to extracellular electron acceptors. Citrobacter strain SX‐1 is capable of generating electricity from a wide range of substrates in MFCs. Significance and Impact of the Study: This finding increases the known diversity of power generating exoelectrogens and provided a new strain to explore the mechanisms of extracellular electron transfer from bacteria to electrode. The wide range of substrate utilization by SX‐1 increases the application potential of MFCs in renewable energy generation and waste treatment.     

Effect of nitrogen addition on the performance of microbial fuel cell anodes

Carbon cloth anodes were modified with 4(N,N-dimethylamino)benzene diazonium tetrafluoroborate to increase nitrogen-containing functional groups at the anode surface in order to test whether the performance of microbial fuel cells (MFCs) could be improved by controllably modifying the anode surface chemistry. Anodes with the lowest extent of functionalization, based on a nitrogen/carbon ratio of 0.7 as measured by XPS, achieved the highest power density of 938 mW/m². This power density was 24% greater than an untreated anode, and similar to that obtained with an ammonia gas treatment previously shown to increase power. Increasing the nitrogen/carbon ratio to 3.8, however, decreased the power density to 707 mW/m². These results demonstrate that a small amount of nitrogen functionalization on the carbon cloth material is sufficient to enhance MFC performance, likely as a result of promoting bacterial adhesion to the surface without adversely affecting microbial viability or electron transfer to the surface.     

Improved performance of membrane free single-chamber air-cathode microbial fuel cells with nitric acid and ethylenediamine surface modified activated carbon fiber felt anodes

Surface modifications of anode materials are important for enhancing power generation of microbial fuel cell (MFC). Membrane free single-chamber air-cathode MFCs, MFC-A and MFC-N, were constructed using activated carbon fiber felt (ACF) anodes treated by nitric acid and ethylenediamine (EDA), respectively. Experimental results showed that the start-up time to achieve the maximum voltages for the MFC-A and MFC-N was shortened by 45% and 51%, respectively as compared to that for MFC-AT equipped with an unmodified anode. Moreover, the power output of MFCs with modified anodes was significantly improved. In comparison with MFC-AT which had a maximum power density of 1304 mW/m², the MFC-N achieved a maximum power density of 1641 mW/m². The nitric acid-treated anode in MFC-A increased the power density by 58% reaching 2066 mW/m². XPS analysis of the treated and untreated anode materials indicated that the power enhancement was attributable to the changes of surface functional groups.     

Electrochemical analysis of Clostridium propionicum and its acrylic acid production in microbial fuel cells

Currently, acrylic acid is produced at a low yield by the resting cells of Clostridium propionicum with the supplement of extra electron acceptors. As an alternative way, acrylic acid production coupled with electricity generation was achieved by C. propionicum‐based microbial fuel cells (MFCs). Electricity was generated in the salt‐bridge MFCs with cysteine and resazurin in the anode chamber as mediators, and K₃Fe(CN)₆ as the cathode electron acceptor. Power generation was 21.78 mW/m² with an internal resistance of 9809 Ω. Cyclic voltammograms indicated the main mechanism of power production was the electron transfer facilitated by mediators in the system. In the salt‐bridge MFC system, 0.694 mM acrylic acid was produced together with electricity generation.     

The role of riboflavin in decolourisation of Congo red and bioelectricity production using <Emphasis Type="Italic">Shewanella oneidensis</Emphasis>-MR1 under MFC and non-MFC conditions

Dissimilatory metal reducing bacteria can exchange electrons extracellularly and hold great promise for their use in simultaneous wastewater treatment and electricity production. This study investigated the role of riboflavin, an electron carrier, in the decolourisation of Congo red in microbial fuel cells (MFCs) using Shewanella oneidensis MR-1 as a model organism. The contribution of the membrane-bound protein MtrC to the decolourisation process was also investigated. Within the range of riboflavin concentrations tested, 20 µM was found to be the best with >95% of the dye (initial concentration 200 mg/L) decolourised in MFCs within 50 h compared to 90% in the case where no riboflavin was added. The corresponding maximum power density was 45 mW/m². There was no significant difference in the overall decolourisation efficiencies of Shewanela oneidensis MR-1 ΔMtrC mutants compared to the wild type. However, in terms of power production the mutant produced more power (P_max 76 mW/m²) compared to the wild type (P_max 46 mW/m²) which was attributed to higher levels of riboflavin secreted in solution. Decolourisation efficiencies in non-MFC systems (anaerobic bottles) were similar to those under MFC systems indicating that electricity generation in MFCs does not impair dye decolourisation efficiencies. The results suggest that riboflavin enhances both decolourisation of dyes and simultaneous electricity production in MFCs.     

Change in microbial communities in acetate- and glucose-fed microbial fuel cells in the presence of light

Power densities produced by microbial fuel cells (MFCs) in natural systems are changed by exposure to light through the enrichment of photosynthetic microorganisms. When MFCs with brush anodes were exposed to light (4000 lx), power densities increased by 8–10% for glucose-fed reactors, and 34% for acetate-fed reactors. Denaturing gradient gel electrophoresis (DGGE) profiles based on the 16S rRNA gene showed that exposure to high light levels changed the microbial communities on the anodes. Based on 16S rRNA gene clone libraries of light-exposed systems the anode communities using glucose were also significantly different than those fed acetate. Dominant bacteria that are known exoelectrogens were identified in the anode biofilm, including a purple nonsulfur (PNS) photosynthetic bacterium, Rhodopseudomonas palustris, and a dissimilatory iron-reducing bacterium, Geobacter sulfurreducens. Pure culture tests confirmed that PNS photosynthetic bacteria increased power production when exposed to high light intensities (4000 lx). These results demonstrate that power production and community composition are affected by light conditions as well as electron donors in single-chamber air-cathode MFCs.     

The effect of flavin electron shuttles in microbial fuel cells current production

The effect of electron shuttles on electron transfer to microbial fuel cell (MFC) anodes was studied in systems where direct contact with the anode was precluded. MFCs were inoculated with Shewanella cells, and flavins used as the electron shuttling compound. In MFCs with no added electron shuttles, flavin concentrations monitored in the MFCs' bulk liquid increased continuously with FMN as the predominant flavin. The maximum concentrations were 0.6 μM for flavin mononucleotide and 0.2 μM for riboflavin. In MFCs with added flavins, micro-molar concentrations were shown to increase current and power output. The peak current was at least four times higher in MFCs with high concentrations of flavins (4.5–5.5 μM) than in MFCs with low concentrations (0.2–0.6 μM). Although high power outputs (around 150 mW/m²) were achieved in MFCs with high concentrations of flavins, a Clostridium-like bacterium along with other reactor limitations affected overall coulombic efficiencies (CE) obtained, achieving a maximum CE of 13%. Electron shuttle compounds (flavins) permitted bacteria to utilise a remote electron acceptor (anode) that was not accessible to the cells allowing current production until the electron donor (lactate) was consumed.     

Bioanode of polyurethane/graphite/polypyrrole composite in microbial fuel cells

Polyurethane (PU) foams were coated with graphite, and pyrrole monomer was subsequently polymerized onto its surface by chemical oxidization to obtain nanostructured polyurethane/graphite/polypyrrole (PU/Graph/PPy) composites, which were used for anaerobic microorganisms grown and tested as anodes in microbial fuel cells (MFC) using municipal wastewater as fuel. The effects of oxidizing agent type (ammonium persulfate and FeCl3) used in pyrrole polymerization on the performance of electrodes in MFC were studied. Composites were characterized by Fourier Transform Infrared (FTIR) spectroscopy, Scanning Electron Microscopy (SEM), and by the four-point probes to determine conductivity. It was observed from SEM analysis that globular nanostructures of PPy were formed onto PU surface with average diameters between 120 and 450 nm, which are typical of aqueous polymerization of pyrrole monomer. The highest output power density observed in MFCs was 305.5 mW/m³ for the composite synthesized using FeCl₃ as the oxidant, and 128.6 mW/m³ using the composite obtained with ammonium persulfate as oxidizing; the corresponding chemical oxygen demand (COD) removal were 48.2 and 45.5%, respectively. The calculated coulombic efficiency for PU/Graph/PPy composite obtained with FeCl₃ as oxidant was of 9.4%. Internal resistance of MFC using the composite obtained with FeCl₃ as oxidant was determined by linear sweep voltammetry (LSV) and the variable resistance (VR) methods, giving 4.8 and 2.9 kO, respectively, with average maximum power density of 237.5 mW/m³.     

Factors affecting current production in microbial fuel cells using different industrial wastewaters

This study evaluated how different types of industrial wastewaters (bakery, brewery, paper and dairy) affect the performance of identical microbial fuel cells (MFCs); and the microbial composition and electrochemistry of MFC anodes. MFCs fed with paper wastewater produced the highest current density (125 ± 2 mA/m²) at least five times higher than dairy (25 ± 1 mA/m²), brewery and bakery wastewaters (10 ± 1 mA/m²). Such high current production was independent of substrate degradability. A comprehensive study was conducted to determine the factor driving current production when using the paper effluent. The microbial composition of anodic biofilms differed according to the type of wastewater used, and only MFC anodes fed with paper wastewater showed redox activity at −134 ± 5 mV vs NHE. Electrochemical analysis of this redox activity indicated that anodic bacteria produced a putative electron shuttling compound that increased the electron transfer rate through diffusion, and as a result the overall MFC performance.     

Resource recovery from paddy field using plant microbial fuel cell

The plant microbial fuel cell (PMFC) is a recently developed energy-generating technology that supports sustainable agriculture. Design configuration is the key bottleneck in optimization and upscaling of paddy based PMFCs. In this study, two designs (Type-I (horizontal) and Type-II (vertical)) of terracotta based ceramic PMFCs (C-PMFC) are incorporated into the paddy field to recover nutrients, energy, and water (“NEW”) resources. The peak voltage generated in Type-I and Type-II C-PMFC was 292.1 mV and 321.7 mV respectively. The polarisation study in the ripening phase of paddy showed a maximum power density of 9.1 mW/m² (type-I) and 16.8 mW/m² (type-II). The volume of catholyte recovered is observed to be dependent on the C-PMFC performance and growth phases of the paddy. In the entire 10 weeks of the experimental period, a total of 451 mL and 943 mL of catholyte was collected at 100Ω load in type-I and type-II, respectively. The collected catholyte is alkaline in nature and maximum catholyte recovery is achieved at the active tillering phase and declined with the advancement of the development stages of the plant. Osmotic and electro-osmotic migration of various nutrients like ammonium from the paddy field to cathode chamber of C-PMFC is observed throughout the experiment.     

Characterization of electrochemical activity of a strain ISO2‐3 phylogenetically related to Aeromonas sp. isolated from a glucose‐fed microbial fuel cell

The microbial communities associated with electrodes in closed and open circuit microbial fuel cells (MFCs) fed with glucose were analyzed by 16S rRNA approach and compared. The comparison revealed that bacteria affiliated with the Aeromonas sp. within the Gammaproteobacteria constituted the major population in the closed circuit MFC (harvesting electricity) and considered to play important roles in current generation. We, therefore, attempted to isolate the dominant bacteria from the anode biofilm, successfully isolated a Fe (III)‐reducing bacterium phylogenetically related to Aeromonas sp. and designated as strain ISO2‐3. The isolated strain ISO2‐3 could grow and concomitantly produce current (max. 0.24 A/m²) via oxidation of glucose or hydrogen with an electrode serving as the sole electron acceptor. The strain could ferment glucose, but generate less electrical current. Cyclic voltammetry supported the strain ISO2‐3 was electrically active and likely to transfer electrons to the electrode though membrane‐associated compounds (most likely c‐type cytochrome). This mechanism requires intimate contact with the anode surface. Scanning electron microscopy revealed that the strain ISO2‐3 developed multiplayer biofilms on the anode surface and also produced anchor‐like filamentous appendages (most likely pili) that may promote long‐range electron transport across the thick biofilm. Biotechnol. Bioeng. 2009; 104: 901–910. © 2009 Wiley Periodicals, Inc.     

Comparison of Electrode Reduction Activities of Geobacter sulfurreducens and an Enriched Consortium in an Air-Cathode Microbial Fuel Cell

An electricity-generating bacterium, Geobacter sulfurreducens PCA, was inoculated into a single-chamber, air-cathode microbial fuel cell (MFC) in order to determine the maximum electron transfer rate from bacteria to the anode. To create anodic reaction-limiting conditions, where electron transfer from bacteria to the anode is the rate-limiting step, anodes with electrogenic biofilms were reduced in size and tests were conducted using anodes of six different sizes. The smallest anode (7 cm², or 1.5 times larger than the cathode) achieved an anodic reaction-limiting condition as a result of a limited mass of bacteria on the electrode. Under these conditions, the limiting current density reached a maximum of 1,530 mA/m², and power density reached a maximum of 461 mW/m². Per-biomass efficiency of the electron transfer rate was constant at 32 fmol cell⁻¹ day⁻¹ (178 μmol g of protein⁻¹ min⁻¹), a rate comparable to that with solid iron as the electron acceptor but lower than rates achieved with fumarate or soluble iron. In comparison, an enriched electricity-generating consortium reached 374 μmol g of protein⁻¹ min⁻¹ under the same conditions, suggesting that the consortium had a much greater capacity for electrode reduction. These results demonstrate that per-biomass electrode reduction rates (calculated by current density and biomass density on the anode) can be used to help make better comparisons of electrogenic activity in MFCs.     

Microorganism-immobilized carbon nanoparticle anode for microbial fuel cells based on direct electron transfer

A fast and convenient bacterial immobilization method was proposed as an attempt to improve the anode efficiency of a microbial fuel cell, in which bacteria were entrapped into carbon nanoparticle matrix. The direct electron transfer from the entrapped bacterial cells to the anode was verified using cyclic voltammogram (CV). Using the immobilized bioanode, the start-up time of the MFC was greatly reduced. Meanwhile, the maximum power density of 1,947 mW m⁻² with the modified anode was much higher than that with the biofilm-based carbon cloth anode (1,479 mW m⁻²). Impedance measurements suggested that performance improvement resulted from the decrease in charge transfer and diffusion resistances. The results demonstrated that bacteria immobilization using carbon nanoparticle matrix was a simple and efficient approach for improving the anodes performances in MFCs.     

Effect of external resistance on bacterial diversity and metabolism in cellulose-fed microbial fuel cells

External resistance affects the performance of microbial fuel cells (MFCs) by controlling the flow of electrons from the anode to the cathode. The purpose of this study was to determine the effect of external resistance on bacterial diversity and metabolism in MFCs. Four external resistances (20, 249, 480, and 1000 Ω) were tested by operating parallel MFCs independently at constant circuit loads for 10 weeks. A maximum power density of 66 mW m⁻² was achieved by the 20 Ω MFCs, while the MFCs with 249, 480, and 1000 Ω external resistances produced 57.5, 27, and 47 mW m⁻², respectively. Denaturing gradient gel electrophoresis analysis of partial 16S rRNA genes showed clear differences between the planktonic and anode-attached populations at various external resistances. Concentrations of short chain fatty acids were higher in MFCs with larger circuit loads, suggesting that fermentative metabolism dominated over anaerobic respiration using the anode as the final electron acceptor.     

Microbial fuel cell energy from an ocean cold seep

Benthic microbial fuel cells are devices that generate modest levels of electrical power in seafloor environments by a mechanism analogous to the coupled biogeochemical reactions that transfer electrons from organic carbon through redox intermediates to oxygen. Two benthic microbial fuel cells were deployed at a deep-ocean cold seep within Monterey Canyon, California, and were monitored for 125 days. Their anodes consisted of single graphite rods that were placed within microbial mat patches of the seep, while the cathodes consisted of carbon-fibre/titanium wire brushes attached to graphite plates suspended ∼0.5 m above the sediment. Power records demonstrated a maximal sustained power density of 34 mW·m⁻² of anode surface area, equating to 1100 mW m⁻² of seafloor. Molecular phylogenetic analyses of microbial biofilms that formed on the electrode surfaces revealed changes in microbial community composition along the anode as a function of sediment depth and surrounding geochemistry. Near the sediment surface (20–29 cm depth), the anodic biofilm was dominated by micro-organisms closely related to Desulfuromonas acetoxidans. At horizons 46–55 and 70–76 cm below the sediment–water interface, clone libraries showed more diverse populations, with increasing representation of δ-proteobacteria such as Desulfocapsa and Syntrophus, as well as ɛ-proteobacteria. Genes from phylotypes related to Pseudomonas dominated the cathode clone library. These results confound ascribing a single electron transport role performed by only a few members of the microbial community to explain energy harvesting from marine sediments. In addition, the microbial fuel cells exhibited slowly decreasing current attributable to a combination of anode passivation and sulfide mass transport limitation. Electron micrographs of fuel cell anodes and laboratory experiments confirmed that sulfide oxidation products can build up on anode surfaces and impede electron transfer. Thus, while cold seeps have the potential to provide more power than neighbouring ocean sediments, the limits of mass transport as well as the proclivity for passivation must be considered when developing new benthic microbial fuel cell designs to meet specific power requirements.     

Effect of vitamins and cell constructions on the activity of microbial fuel cell battery

Construction of efficient performance of microbial fuel cells (MFCs) requires certain practical considerations. In the single chamber microbial fuel cell, there is no border between the anode and the cathode, thus the diffusion of the dissolved oxygen has a contrary effect on the anodic respiration and this leads to the inhibition of the direct electron transfer from the biofilm to the anodic surface. Here, a fed-batch single chambered microbial fuel cells are constructed with different distances 3 and 6?cm (anode- cathode spacing), while keeping the working volume is constant. The performance of each MFC is individually evaluated under the effects of vitamins & minerals with acetate as a fed load. The maximum open circuit potential during testing the 3 and 6?cm microbial fuel cells is about 946 and 791?mV respectively. By decreasing the distance between the anode and the cathode from 6 to 3?cm, the power density is decreased from 108.3?mW?m^?2 to 24.5?mW?m^?2. Thus, the short distance in membrane-less MFC weakened the cathode and inhibited the anodic respiration which affects the overall performance of the MFC efficiency. The system is displayed a maximum potential of 564 and 791?mV in absence & presence of vitamins respectively. Eventually, the overall functions of the acetate single chamber microbial fuel cell can be improved by the addition of vitamins & minerals and increasing the distance between the cathode and the anode.     

Simultaneous analysis of physiological and electrical output changes in an operating microbial fuel cell with Shewanella oneidensis

Changes in metabolism and cellular physiology of facultative anaerobes during oxygen exposure can be substantial, but little is known about how these changes connect with electrical current output from an operating microbial fuel cell (MFC). A high‐throughput voltage based screening assay (VBSA) was used to correlate current output from a MFC containing Shewanella oneidensis MR‐1 to carbon source (glucose or lactate) utilization, culture conditions, and biofilm coverage over 250 h. Lactate induced an immediate current response from S. oneidensis MR‐1, with both air‐exposed and anaerobic anodes throughout the duration of the experiments. Glucose was initially utilized for current output by MR‐1 when cultured and maintained in the presence of air. However, after repeated additions of glucose, the current output from the MFC decreased substantially while viable planktonic cell counts and biofilm coverage remained constant suggesting that extracellular electron transfer pathways were being inhibited. Shewanella maintained under an anaerobic atmosphere did not utilize glucose consistent with literature precedents. Operation of the VBSA permitted data collection from nine simultaneous S. oneidensis MR‐1 MFC experiments in which each experiment was able to demonstrate organic carbon source utilization and oxygen dependent biofilm formation on a carbon electrode. These data provide the first direct evidence of complex cellular responses to electron donor and oxygen tension by Shewanella in an operating MFC at select time points. Biotechnol. Bioeng. 2009;103: 524–531. Published 2009 Wiley Periodicals, Inc.     

Domestic wastewater treatment using multi-electrode continuous flow MFCs with a separator electrode assembly design

Treatment of domestic wastewater using microbial fuel cells (MFCs) will require reactors with multiple electrodes, but this presents unique challenges under continuous flow conditions due to large changes in the chemical oxygen demand (COD) concentration within the reactor. Domestic wastewater treatment was examined using a single-chamber MFC (130 mL) with multiple graphite fiber brush anodes wired together and a single air cathode (cathode specific area of 27 m²/m³). In fed-batch operation, where the COD concentration was spatially uniform in the reactor but changed over time, the maximum current density was 148?±?8 mA/m² (1,000 Ω), the maximum power density was 120 mW/m², and the overall COD removal was >90 %. However, in continuous flow operation (8 h hydraulic retention time, HRT), there was a 57 % change in the COD concentration across the reactor (influent versus effluent) and the current density was only 20?±?13 mA/m². Two approaches were used to increase performance under continuous flow conditions. First, the anodes were separately wired to the cathode, which increased the current density to 55?±?15 mA/m². Second, two MFCs were hydraulically connected in series (each with half the original HRT) to avoid large changes in COD among the anodes in the same reactor. The second approach improved current density to 73?±?13 mA/m². These results show that current generation from wastewaters in MFCs with multiple anodes, under continuous flow conditions, can be improved using multiple reactors in series, as this minimizes changes in COD in each reactor.