Creating Highly Active Atomic Layer Deposited NiO Electrocatalysts for the Oxygen Evolution Reaction

Atomic layer deposition (ALD) provides a promising route for depositing uniform thin coatings of electrocatalysts useful in many technologies, including the splitting of water. For materials such as NiO _x that readily form hydrous oxides, however, the smooth, compact films deposited by ALD may result in higher overpotentials due to low catalyst surface area compared to other deposition methods. Here, the use of ALD–NiO thin films as oxygen evolution reaction (OER) electrocatalysts is explored. Thin films of crystalline ALD­–NiO are deposited and OER activity is tested using cyclic voltammetry (CV). Fe incorporated from the electrolyte can increase the activity of NiO, and it is shown that the turnover frequency (TOF) increases tenfold by going from an Fe‐poor to Fe‐rich KOH electrolyte. Applying a potential exfoliates the NiO, increasing the number of electrochemically accessible Ni sites. Interestingly, by X‐ray photoelectron spectroscopy (XPS) and CV, it is found that an Fe‐rich electrolyte reduces the amount of restructuring and oxidation is found. It is shown that a high surface area, high TOF catalyst may be created by using a two‐step process in which the sample is sequentially conditioned in Fe‐poor then Fe‐rich KOH. This work highlights the importance of pretreatment on catalytic activity for compact NiO films deposited by ALD.     

Bimetallic Zeolitic Imidazolite Framework Derived Carbon Nanotubes Embedded with Co Nanoparticles for Efficient Bifunctional Oxygen Electrocatalyst

Bifunctional oxygen catalysts for oxygen reduction reaction (ORR) and oxygen evolution reaction (OER) with high activities and low‐cost are of prime importance and challenging in the development of fuel cells and rechargeable metal–air batteries. This study reports a porous carbon nanomaterial loaded with cobalt nanoparticles (Co@NC‐x/y) derived from pyrolysis of a Co/Zn bimetallic zeolitic imidazolite framework, which exhibits incredibly high activity as bifunctional oxygen catalysts. For instance, the optimal catalyst of Co@NC‐3/1 has the interconnected framework structure between porous carbon and embedded carbon nanotubes, which shows the superb ORR activity with onset potential of ≈1.15 V and half‐wave potential of ≈0.93 V. Moreover, it presents high OER activity that can be further enhanced to over commercial RuO₂ by P‐doped with overpotentials of 1.57 V versus reversible hydrogen electrode at 10 mA cm^?2 and long‐term stability for 2000 circles and a Tafel slope of 85 mV dec^?1. Significantly, the nanomaterial demonstrates better catalytic performance and durability than Pt/C for ORR and commercial RuO₂ and IrO₂ for OER. These findings suggest the importance of a synergistic effect of graphitic carbon, nanotubes, exposed Co–N_x active sites, and interconnected framework structure of various carbons for bifunctional oxygen electrocatalysts.     

Enhanced Stability and Thickness‐Independent Oxygen Evolution Electrocatalysis of Heterostructured Anodes with Buried Epitaxial Bilayers

Achieving high oxygen evolution reaction (OER) activity while maintaining performance stability is a key challenge for designing perovskite structure oxide OER catalysts, which are often unstable in alkaline environments transforming into an amorphous phase. While the chemical and structural transformation occurring during electrolysis at the electrolyte–catalyst interface is now regarded as a crucial factor influencing OER activity, here, using La_0.7Sr_0.3CoO_3?δ (LSCO) as an active OER catalyst, the critical influence of buried layers on the oxidation current stability in nanoscopically thin, chemically and structurally evolving, catalyst layers is revealed. The use of epitaxial thin films is demonstrated to engineer both depletion layer widths and chemical stability of the catalyst support structure resulting in heterostructured anodes that maintain facile transport kinetics across the electrolyte–anode interface for atomically thin (2–3 unit cells) LSCO catalyst layers and greatly enhanced oxidation current stability as the perovskite structure OER catalysts chemically and structurally transform. This work opens up an approach to design robust and active heterostructured anodes with dynamically evolving ultrathin OER electrocatalyst layers for future green fuel technologies such as conformal coatings of high‐density 3D anode topologies for water splitting.     

Novel Route to Fe‐Based Cathode as an Efficient Bifunctional Catalysts for Rechargeable Zn–Air Battery

Efficient bifunctional oxygen reduction reaction (ORR) and oxygen evolution reaction (OER) catalysts are of great importance for rechargeable metal–air batteries. Herein, FeN_x/C catalysts are synthesized by pyrolysis of thiourea and agarose containing α‐Fe₂O₃ nanoplate as Fe precursor, where α‐Fe₂O₃ nanoplate can prevent the aggregation of carbon sheets to effectively improve the specific surface area during the carbonization process. The FeN_x/C‐700‐20 catalyst displays excellent catalytic performance for both ORR and OER activity in alkaline conditions with more positive onset potential (1.1 V vs the reversible hydrogen electrode) and half‐wave potential, higher stability, and stronger methanol tolerance in alkaline solution, which are all superior to that of the commercial Pt/C catalyst. In this study, the detailed analyses demonstrate that the coexistence of Fe‐based species and high content of Fe‐N_x both play an important role for the catalytic activity. Furthermore, FeN_x/C‐700‐20 as cathode catalyst in Zn–air battery possesses higher charge–discharge stability and power density compared with that of commercial Pt/C catalyst, displaying great potential in practical implementation of for the rechargeable energy devices.     

Tunable Internal and Surface Structures of the Bifunctional Oxygen Perovskite Catalysts

Perovskite oxide ceramics attracts significant attention as a strong candidate of bifunctional oxygen reduction reaction (ORR) and oxygen evolution reaction (OER) electrocatalyst for the metal‐air batteries. Numerous approaches to the viability of bifunctional perovskite electrocatalyst represent that the electro­chemical performance is highly correlated with defect chemistry, surface structure, and overall polycrystalline perovskite structure. By making use of the intrinsic flexibility of internal structure and high nonstoichiometry in perovskite oxide, the heat treatment effect of the complex Ba_0.5Sr_0.5Co_xFe_1‐xO_3‐δ (x = 0.2 and 0.8) perovskites in argon atmosphere at 950 °C (Ar‐BSCF5582 and Ar‐BSCF5528) on the surface structure/defect chemistry and electrocatalytic performance is intensively investigated. Upon heat‐treatment in argon atmosphere, the amorphous thickness layer increases from ≈20 to 180–200 nm in BSCF5582, while there is little change in BSCF5528 with ≈20 nm. The electrocatalytic performance of BSCF5582 catalyst both in ORR and OER deteriorates seriously, while Ar‐BSCF5528 demonstrates a significant increase of electro­chemical performance in ORR. This study demonstrates that the electrochemical performances of a perovskite catalyst can be significantly determined by the simultaneous modification of both surface structure and internal defect chemistry, which are explained with transmission electron microscopy and atomic‐selective X‐ray absorption fine structure analyses, respectively.     

Electrodeposited MnOx Films from Ionic Liquid for Electrocatalytic Water Oxidation

A novel method for the electrodeposition of highly active water oxidation catalysts is described. The manganese oxide (MnO_x) films are electrodeposited on fluorine tin oxide (FTO) glass substrate at high temperature (120 °C) from an ionic liquid electrolyte (ethylammonium nitrate). A range of analytical techniques, including X‐ray absorption spectroscopy (XAS), X‐ray diffraction (XRD), and energy‐dispersive X‐ray analyzer (EDX), indicate that the valence state of manganese in the deposited films can be controlled by changing the electrolyte composition. Along with the different phase compositions, a number of different morphologies including nanowires, nanoparticles, nanofibers as well as highly open and dense structures are obtained by varying the acidity of the electrolyte. The effect of morphology and chemical composition on the catalytic activity towards water oxidation is investigated. The film composed of Mn₃O₄ shows low catalytic activities, while the films composed of birnessite‐like manganese oxide phase and Mn₂O₃ exhibit high catalytic activities for water oxidation. The catalytic activities are also affected by the surface morphology, i.e., a higher surface area and more open structure shows a higher catalytic activity. High rates of oxygen production are observed from MnO_x films prepared in a neutral electrolyte.     

Ultrathin High Surface Area Nickel Boride (NixB) Nanosheets as Highly Efficient Electrocatalyst for Oxygen Evolution

The overriding obstacle to mass production of hydrogen from water as the premium fuel for powering our planet is the frustratingly slow kinetics of the oxygen evolution reaction (OER). Additionally, inadequate understanding of the key barriers of the OER is a hindrance to insightful design of advanced OER catalysts. This study presents ultrathin amorphous high‐surface area nickel boride (Ni_x B) nanosheets as a low‐cost, very efficient and stable catalyst for the OER for electrochemical water splitting. The catalyst affords 10 mA cm^?2 at 0.38 V overpotential during OER in 1.0 m KOH, reducing to only 0.28 V at 20 mA cm^?2 when supported on nickel foam, which ranks it among the best reported nonprecious catalysts for oxygen evolution. Operando X‐ray absorption fine‐structure spectroscopy measurements reveal prevalence of NiOOH, as well as Ni‐B under OER conditions, owing to a Ni‐B core@nickel oxyhydroxide shell (Ni‐B@NiO_x H) structure, and increase in disorder of the NiO_x H layer, thus revealing important insight into the transient states of the catalyst during oxygen evolution.     

Atomically Dispersed Fe‐Nx/C Electrocatalyst Boosts Oxygen Catalysis via a New Metal‐Organic Polymer Supramolecule Strategy

The development of high‐performance oxygen reduction reaction (ORR) catalysts derived from non‐Pt group metals (non‐PGMs) is urgent for the wide applications of proton exchange membrane fuel cells (PEMFCs). In this work, a facile and cost‐efficient supramolecular route is developed for making non‐PGM ORR catalyst with atomically dispersed Fe‐N_x/C sites through pyrolyzing the metal‐organic polymer coordinative hydrogel formed between Fe³⁺ and α‐L‐guluronate blocks of sodium alginate (SA). High‐angle annular dark field scanning transmission electron microscopy (HAADF‐STEM) and X‐ray absorption spectroscopy (XAS) verify that Fe atoms achieve atomic‐level dispersion on the obtained SA‐Fe‐N nanosheets and a possible fourfold coordination with N atoms. The best‐performing SA‐Fe‐N catalyst exhibits excellent ORR activity with half‐wave potential (E_1/2) of 0.812 and 0.910 V versus the reversible hydrogen electrode (RHE) in 0.5 m H₂SO₄ and 0.1 m KOH, respectively, along with respectable durability. Such performance surpasses that of most reported non‐PGM ORR catalysts. Density functional theory calculations suggest that the relieved passivation effect of OH* on Fe‐N₄/C structure leads to its superior ORR activity to Pt/C in alkaline solution. The work demonstrates a novel strategy for developing high‐performance non‐PGM ORR electrocatalysts with atomically dispersed and stable M‐N_x coordination sites in both acidic and alkaline media.     

Controlling the Active Sites of Sulfur‐Doped Carbon Nanotube–Graphene Nanolobes for Highly Efficient Oxygen Evolution and Reduction Catalysis

Controlling active sites of metal‐free catalysts is an important strategy to enhance activity of the oxygen evolution reaction (OER). Many attempts have been made to develop metal‐free catalysts, but the lack of understanding of active‐sites at the atomic‐level has slowed the design of highly active and stable metal‐free catalysts. A sequential two‐step strategy to dope sulfur into carbon nanotube–graphene nanolobes is developed. This bidoping strategy introduces stable sulfur–carbon active‐sites. Fluorescence emission of the sulfur K‐edge by X‐ray absorption near edge spectroscopy (XANES) and scanning transmission electron microscopy electron energy loss spectroscopy (STEM‐EELS) mapping and spectra confirm that increasing the incorporation of heterocyclic sulfur into the carbon ring of CNTs not only enhances OER activity with an overpotential of 350 mV at a current density of 10 mA cm^?2, but also retains 100% of stability after 75 h. The bidoped sulfur carbon nanotube–graphene nanolobes behave like the state‐of‐the‐art catalysts for OER but outperform those systems in terms of turnover frequency (TOF) which is two orders of magnitude greater than (20% Ir/C) at 400 mV overpotential with very high mass activity 1000 mA cm^?2 at 570 mV. Moreover, the sulfur bidoping strategy shows high catalytic activity for the oxygen reduction reaction (ORR). Stable bifunctional (ORR and OER) catalysts are low cost, and light‐weight bidoped sulfur carbon nanotubes are potential candidates for next‐generation metal‐free regenerative fuel cells.     

Highly Active and Stable Graphene Tubes Decorated with FeCoNi Alloy Nanoparticles via a Template‐Free Graphitization for Bifunctional Oxygen Reduction and Evolution

Development of highly active and stable bifunctional oxygen reduction reaction (ORR) and oxygen evolution reaction (OER) catalysts from earth‐abundant elements remains a grand challenge for highly demanded reversible fuel cells and metal–air batteries. Carbon catalysts have many advantages over others due to their low cost, excellent electrical conductivity, high surface area, and easy functionalization. However, they typically cannot withstand the highly oxidative OER environment. Here, a new class of bifunctional electrocatalyst is reported, consisting of ultralarge sized nitrogen doped graphene tubes (N‐GTs) (>500 nm) decorated with FeCoNi alloy particles. These tubes are prepared from an inexpensive precursor, dicyandiamide, via a template‐free graphitization process. The ORR/OER activity and the stability of these graphene tube catalysts depend strongly on the transition metal precursors. The best performing FeCoNi‐derived N‐GT catalyst exhibits excellent ORR and OER activity along with adequate electrochemical durability over a wide potential window (0–1.9 V) in alkaline media. The measured OER current is solely due to desirable O₂ evolution, rather than carbon oxidation. Extensive electrochemical and physical characterization indicated that high graphitization degree, thicker tube walls, proper nitrogen doping, and presence of FeCoNi alloy particles are vital for high bifunctional activity and electrochemical durability of tubular carbon catalysts.     

Pt‐Ir‐Pd Trimetallic Nanocages as a Dual Catalyst for Efficient Oxygen Reduction and Evolution Reactions in Acidic Media

The development of dual catalysts with high efficiency toward oxygen reduction and evolution reactions (ORR and OER) in acidic media is a significant challenge. Here an active and durable dual catalyst based upon cubic Pt₃₉Ir₁₀Pd₁₁ nanocages with an average edge length of 12.3 nm, porous walls as thin as 1.0 nm, and well‐defined {100} facets is reported. The trimetallic nanocages perform better than all the reported dual catalysts in acidic media, with a low ORR‐OER overpotential gap of only 704 mV at a Pt‐Ir‐Pd loading of 16.8 µg_Pt+Ir+Pd cm^?2_geo. For ORR at 0.9 V, when benchmarked against the commercial Pt/C and Pt‐Pd nanocages, the trimetallic nanocages exhibit an enhanced mass activity of 0.52 A mg^?1_Pt+Ir+Pd (about four and two times as high as those of the Pt/C and Pt‐Pd nanocages) and much improved durability. For OER, the trimetallic nanocages show a remarkable mass activity of 0.20 A mg^?1_Pt+Ir at 1.53 V, which is 16.7 and 4.3 fold relative to those of the Pt/C and Pt‐Pd nanocages, respectively. These improvements can be ascribed to the highly open structure of the nanocages, and the possible electronic coupling between Ir and Pt atoms in the lattice.     

Efficiently Enhancing Oxygen Reduction Electrocatalytic Activity of MnO2 Using Facile Hydrogenation

Improving the electrocatalytic oxygen reduction reaction (ORR) activity of transition metal oxides is important for the development of non‐noble metal catalysts that are used in metal‐air batteries and fuel cells. Here, a novel facile strategy of hydrogenation to significantly enhance the ORR performance of MnO₂. The hydrogenated MnO₂ (H‐MnO₂), which is prepared through a simple heat treatment in hydrogen gas, shows characteristics of modified lattice/surface structures and increased electrical conductivity. In 0.1 M KOH aqueous solution, the prepared H‐MnO₂ exhibits high activity toward the oxygen electrocatalysis with more positive onset potential (≈60 mV), ≈14% larger of limiting current, lower yield of peroxide species, and better durability than the pristine oxide. Further conductivity testing and density functional theory (DFT) studies reveal the faster kinetics of ORR after hydrogenation is due to the formation of hydrogen bonds and altered microstructure and improved electronic properties. These results highlight the importance of hydrogenation as a facile yet effective strategy to improve the catalytic activity of transition metal oxides for ORR‐based applications.     

Carbon Nanodot Surface Modifications Initiate Highly Efficient,Stable Catalysts for Both Oxygen Evolution and Reduction Reactions

Efficient, stable, and low‐cost electrocatalysts for the oxygen evolution and reduction reactions (OER and ORR) are essential components of energy conversion. Although much progress has been achieved in the development of platinum‐based electrocatalysts for ORR and iridium‐based electrocatalysts for OER, they are still not yet viable for large‐scale commercialization because of the high cost and scanty supply of the noble metals. Here, it is demonstrated that carbon nanodots surface‐modified with either phosphorus or amidogen can respectively achieve electrocatalytic activity approaching that of the benchmark Pt/C and IrO₂ /C catalysts for ORR and OER. Furthermore, phosphorus (amidogen)‐modified carbon nanodots with attached Au nanoparticles exhibit superior ORR (OER) activity better than commercial Pt/C (IrO₂/C) catalysts as well as excellent electrochemical stability under visible light.     

Electrocatalytic Oxygen Evolution Reaction in Acidic Environments – Reaction Mechanisms and Catalysts

The low efficiency of the electrocatalytic oxidation of water to O₂ (oxygen evolution reaction‐OER) is considered as one of the major roadblocks for the storage of electricity from renewable sources in form of molecular fuels like H₂ or hydrocarbons. Especially in acidic environments, compatible with the powerful proton exchange membrane (PEM), an earth‐abundant OER catalyst that combines high activity and high stability is still unknown. Current PEM‐compatible OER catalysts still rely mostly on Ir and/or Ru as active components, which are both very scarce elements of the platinum group. Hence, the Ir and/or Ru amount in OER catalysts has to be strictly minimized. Unfortunately, the OER mechanism, which is the most powerful tool for OER catalyst optimization, still remains unclear. In this review, we first summarize the current state of our understanding of the OER mechanism on PEM‐compatible heterogeneous electrocatalysts, before we compare and contrast that to the OER mechanism on homogenous catalysts. Thereafter, an overview over monometallic OER catalysts is provided to obtain insights into structure‐function relations followed by a review of current material optimization concepts and support materials. Moreover, missing links required to complete the mechanistic picture as well as the most promising material optimization concepts are pointed out.     

Graphitic Nanoshell/Mesoporous Carbon Nanohybrids as Highly Efficient and Stable Bifunctional Oxygen Electrocatalysts for Rechargeable Aqueous Na–Air Batteries

Efficient and cost‐effective bifunctional electrocatalysts for oxygen evolution reaction (OER) and oxygen reduction reaction (ORR) are of vital importance in energy conversion and storage devices. Despite the recent progress in bifunctional oxygen electrocatalysts, their unbalanced and insufficient OER and ORR activities has continued to pose challenges for the practical application of such energy devices. The design of highly integrated, high‐performance, bifunctional oxygen electrocatalysts composed of highly graphitic nanoshells embedded in mesoporous carbon (GNS/MC) is reported. The GNS/MC exhibits very high oxygen electrode activity, which is one of the best performances among nonprecious metal bifunctional oxygen electrocatalysts, and substantially outperforms Ir‐ and Pt‐based catalysts. Moreover, the GNS/MC shows excellent durability for both OER and ORR. In situ X‐ray absorption spectroscopy and square wave voltammetry reveal the roles of residual Ni and Fe entities in enhancing OER and ORR activities. Raman spectra indicate highly graphitic, defect‐rich nature of the GNS/MC, which can contribute to the enhanced OER activity and to high stability for the OER and ORR. In aqueous Na–air battery tests, the GNS/MC air cathode‐based cell exhibits superior performance to Ir/C‐ and Pt/C‐based batteries. Significantly, the GNS/MC‐based cell demonstrates the first example of rechargeable aqueous Na–air battery.     

Engineering of a Low‐Cost,Highly Active,and Durable Tantalate–Graphene Hybrid Electrocatalyst for Oxygen Reduction

The oxygen reduction reaction (ORR) is one of the most important reactions in renewable energy conversion and storage devices. The full deployment of these devices depends on the development of highly active, stable, and low‐cost catalysts. Herein, a new hybrid material consisting of Na₂Ta₈O_21?x/Ta₂O₅/Ta₃N₅ nanocrystals grown on N‐doped reduced graphene oxide is reported. This catalyst shows a significantly enhanced ORR activity by ≈4 orders of magnitude in acidic media and by ≈2 orders of magnitude in alkaline media compared to individual Na₂Ta₈O_21?x on graphene. Moreover, it has excellent stability in both acid and alkaline media. It also has much better methanol tolerance than the commercial Pt/C, which is relevant to methanol fuel cells. The high ORR activity arises not only from the synergistic effect among the three Ta phases, but also from the concomitant nitrogen doping of the reduced graphene oxide nanosheets. A correlation between ORR activity and nitrogen content is demonstrated. Deep insights into the mechanism of the synergistic effect among these three Ta‐based phases, which boosts the ORR's kinetics, are acquired by combining specific experiments and density functional theory calculations.     

Intrinsic Effects of Ruddlesden‐Popper‐Based Bifunctional Catalysts for High‐Temperature Oxygen Reduction and Evolution

Unveiling the intrinsic effects of Ruddlesden‐Popper (RP) series A_n+1B_nO_3n+1 (A = La, B = Ni, Co, Mn, Cu, n = 1, 2 and 3) catalysts is essential in order to optimize the activity of oxygen reduction reaction (ORR) and evolution reaction (OER). Here, it is demonstrated that the oxygen vacancy is not the key point for RP to realize high ORR and OER activity at high temperature. Instead, interstitial O^2? with high concentration and fast migration, and lattice oxygen with high activity are favorable for the high‐temperature catalytic activity. Aliovalent cation doping is an effective strategy to modify the catalytic activity. For the RP catalysts, low‐valence ion doping does not introduce oxygen vacancies, which suppresses the activity of lattice oxygen and decreases the interstitial O^2? concentration; whereas high‐valence ion doping enhances the interstitial O^2– concentration and the lattice oxygen activity. The evaluations of six RP series (La₂NiO₄, La₂CoO₄, La₃Co₂O₇, La₄Ni₃O₁₀, La₂MnO₄, and La₂CuO₄ based) and twenty samples as oxygen electrodes for solid oxide fuel cells (SOFCs) and solid oxide electrolysis cells (SOECs) demonstrate that this finding is applicable to all the selected RP series.     

High‐Performance Trifunctional Electrocatalysts Based on FeCo/Co2P Hybrid Nanoparticles for Zinc–Air Battery and Self‐Powered Overall Water Splitting

Currently, it is still a significant challenge to simultaneously boost various reactions by one electrocatalyst with high activity, excellent durability, as well as low cost. Herein, hybrid trifunctional electrocatalysts are explored via a facile one‐pot strategy toward an efficient oxygen reduction reaction (ORR), oxygen evolution reaction (OER), and hydrogen evolution reaction (HER). The catalysts are rationally designed to be composed by FeCo nanoparticles encapsuled in graphitic carbon films, Co₂P nanoparticles, and N,P‐codoped carbon nanofiber networks. The FeCo nanoparticles and the synergistic effect from Co₂P and FeCo nanoparticles make the dominant contributions to the ORR, OER, and HER activities, respectively. Their bifunctional activity parameter (?E) for ORR and OER is low to 0.77 V, which is much smaller than those of most nonprecious metal catalysts ever reported, and comparable with state‐of‐the‐art Pt/C and RuO₂ (0.78 V). Accordingly, the as‐assembled Zn–air battery exhibits a high power density of 154 mW cm^?2 with a low charge–discharge voltage gap of 0.83 V (at 10 mA cm^?2) and excellent stability. The as‐constructed overall water‐splitting cell achieves a current density of 10 mA cm^?2 (at 1.68 V), which is comparable to the best reported trifunctional catalysts.     

Toward an Active and Stable Catalyst for Oxygen Evolution in Acidic Media: Ti‐Stabilized MnO2

Catalysts are required for the oxygen evolution reaction, which are abundant, active, and stable in acid. MnO₂ is a promising candidate material for this purpose. However, it dissolves at high overpotentials. Using first‐principles calculations, a strategy to mitigate this problem by decorating undercoordinated surface sites of MnO₂ with a stable oxide is developed here. TiO₂ stands out as the most promising of the different oxides in the simulations. This prediction is experimentally verified by testing sputter‐deposited thin films of MnO₂ and Ti–MnO₂. A combination of electrochemical measurements, quartz crystal microbalance, inductively coupled plasma mass spectrometry measurements, and X‐ray photoelectron spectroscopy is performed. Small amounts of TiO₂ incorporated into MnO₂ lead to a moderate improvement in stability, with only a small decrease in activity. This study opens up the possibility of engineering surface properties of catalysts so that active and abundant nonprecious metal oxides can be used in acid electrolytes.     

Defective Carbon–CoP Nanoparticles Hybrids with Interfacial Charges Polarization for Efficient Bifunctional Oxygen Electrocatalysis

The development of efficient catalysts for both oxygen reduction and evolution reactions (oxygen reduction reaction (ORR) and oxygen evolution reaction (OER)) is central to regenerative fuel cells and rechargeable metal–air batteries. It is highly desirable to achieve the efficient integration of dual active components into the catalysts and to understand the interaction between the dual components. Here, a facile approach is demonstrated to construct defective carbon–CoP nanoparticle hybrids as bifunctional oxygen electrocatalysts, and further probe the interfacial charge distribution behavior. By combining multiple synchrotron‐based X‐ray spectroscopic characterizations with density functional theory calculations, the interfacial charge polarization with the electrons gathering at the defective carbon surface and the holes gathering at the CoP surface due to strong interfacial coupling is revealed, which simultaneously facilitates the ORR and OER with remarkable bifunctional oxygen electrode activities. This work not only offers a bifunctional oxygen catalyst with outstanding performance, but also unravels the promoting factor of the hybrids from the view of interfacial charge distribution.