3D Amorphous Carbon with Controlled Porous and Disordered Structures as a High‐Rate Anode Material for Sodium‐Ion Batteries

Sodium‐ion batteries (SIBs) have a promising application prospect for energy storage systems due to the abundant resource. Amorphous carbon with high electronic conductivity and high surface area is likely to be the most promising anode material for SIBs. However, the rate capability of amorphous carbon in SIBs is still a big challenge because of the sluggish kinetics of Na⁺ ions. Herein, a three‐dimensional amorphous carbon (3DAC) with controlled porous and disordered structures is synthesized via a facile NaCl template‐assisted method. Combination of open porous structures of 3DAC, the increased disordered structures can not only facilitate the diffusion of Na⁺ ions but also enhance the reversible capacity of Na storage. When applied as anode materials for SIBs, 3DAC exhibits excellent rate capability (66 mA h g^?1 at 9.6 A g^?1) and high reversible capacity (280 mA h g^?1 at a low current density of 0.03 A g^?1). Moreover, the controlled porous structures by the NaCl template method provide an appropriate specific surface area, which contributes to a relatively high initial Coulombic efficiency of 75%. Additionally, the high‐rate 3DAC material is prepared via a green approach originating from low‐cost pitch and NaCl template, demonstrating an appealing development of carbon anode materials for SIBs.     

Ultrathin MoS2 Nanosheets as Anode Materials for Sodium‐Ion Batteries with Superior Performance

Few‐layer MoS₂ nanosheets are successfully synthesized using a simple and scalable ultrasonic exfoliation technique. The thicknesses of the MoS₂ nanosheets ares about 10 nm as measured by scanning electron microscopy (SEM) and atomic force microscopy (AFM). The unique nanosheet architecture renders the high‐rate transportation of sodium ions due to the short diffusion paths provided by ultrathin thickness and the large interlayer space within the MoS₂ crystal structure (d₍₀₀₂₎ = 6.38 Å). When applied as anode materials in sodium‐ion batteries, MoS₂ nanosheets exhibit a high, reversible sodium storage capacity and excellent cyclability. The MoS₂ nanosheets also demonstrate good electrochemical performance at high current densities.     

Hard Carbon Microtubes Made from Renewable Cotton as High‐Performance Anode Material for Sodium‐Ion Batteries

Sodium‐ion batteries (SIBs) have attracted more and more attention for scalable electrical energy storage due to the abundance and wide distribution of Na resources. However, the anode still remains a great challenge for the application of SIBs. Here the production of uniform hard carbon microtubes (HCTs) made from natural cotton through one simple carbonization process and their application as an anode are reported. The study shows that the electrochemical performance of the HCTs is seriously affected by the carbonization temperature due to the difference in their microstructure and heteroatomic content. The HCTs carbonized at 1300 °C deliver the highest reversible capacity of 315 mAh g^?1 and good rate capability due to their unique tubular structure. This contribution not only provides a new approach for the preparation of hard carbon materials with unique tubular microstructure using natural inspiration, but it also deepens the fundamental understanding of the sodium storage mechanism.     

MoS2/Graphene Nanosheets from Commercial Bulky MoS2 and Graphite as Anode Materials for High Rate Sodium‐Ion Batteries

Tuning heterointerfaces between hybrid phases is a very promising strategy for designing advanced energy storage materials. Herein, a low‐cost, high‐yield, and scalable two‐step approach is reported to prepare a new type of hybrid material containing MoS₂/graphene nanosheets prepared from ball‐milling and exfoliation of commercial bulky MoS₂ and graphite. When tested as an anode material for a sodium‐ion battery, the as‐prepared MoS₂/graphene nanosheets exhibit remarkably high rate capability (284 mA h g^?1 at 20 A g^?1 (≈30C) and 201 mA h g^?1 at 50 A g^?1 (≈75C)) and excellent cycling stability (capacity retention of 95% after 250 cycles at 0.3 A g^?1). Detailed experimental measurements and density functional theory calculation reveal that the functional groups in 2D MoS₂/graphene heterostructures can be well tuned. The impressive rate capacity of the as‐prepared MoS₂/graphene hybrids should be attributed to the heterostructures with a low degree of defects and residual oxygen containing groups in graphene, which subsequently improve the electronic conductivity of graphene and decrease the Na⁺ diffusion barrier at the MoS₂/graphene interfaces in comparison with the acid treated one.     

Na‐Mn‐O Nanocrystals as a High Capacity and Long Life Anode Material for Li‐Ion Batteries

Searching for a new material to build the next‐generation rechargeable lithium‐ion batteries (LIBs) with high electrochemical performance is urgently required. Owing to the low‐cost, non‐toxicity, and high‐safety, the family of manganese oxide including the Na‐Mn‐O system is regarded as one of the most promising electrode materials for LIBs. Herein, a new strategy is carried out to prepare a highly porous and electrochemically active Na_0.55Mn₂O₄·1.5H₂O (SMOH) compound. As an anode material, the Na‐Mn‐O nanocrystal material dispersed within a carbon matrix manifests a high reversible capacity of 1015.5 mA h g^?1 at a current density of 0.1 A g^?1. Remarkably, a considerable capability of 546.8 mA h g^?1 remains even after 2000 discharge/charge cycles at the higher current density of 4 A g^?1, indicating a splendid cyclability. The exceptional electrochemical properties allow SMOH to be a promising anode material toward LIBs.     

Nanosheets‐Assembled CuSe Crystal Pillar as a Stable and High‐Power Anode for Sodium‐Ion and Potassium‐Ion Batteries

Thanks to low costs and the abundance of the resources, sodium‐ion (SIBs) and potassium‐ion batteries (PIBs) have emerged as leading candidates for next‐generation energy storage devices. So far, only few materials can serve as the host for both Na⁺ and K⁺ ions. Herein, a cubic phase CuSe with crystal‐pillar‐like morphology (CPL‐CuSe) assembled by the nanosheets are synthesized and its dual functionality in SIBs and PIBs is comprehensively studied. The electrochemical measurements demonstrate that CPL‐CuSe enables fast Na⁺ and K⁺ storage as well as the sufficiently long duration. Specifically, the anode delivers a specific capacity of 295 mA h g^?1 at current density of 10 A g^?1 in SIBs, while 280 mA h g^?1 at 5 A g^?1 in PIBs, as well as the high capacity retention of nearly 100% over 1200 cycles and 340 cycles, respectively. Remarkably, CPL‐CuSe exhibits a high initial coulombic efficiency of 91.0% (SIBs) and 92.4% (PIBs), superior to most existing selenide anodes. A combination of in situ X‐ray diffraction and ex situ transmission electron microscopy tests fundamentally reveal the structural transition and phase evolution of CuSe, which shows a reversible conversion reaction for both cells, while the intermediate products are different due to the sluggish K⁺ insertion reaction.