EDTA-assisted phytoextraction of heavy metals by turfgrass from municipal solid waste compost using permeable barriers and associated potential leaching risk

A column experiment with horizontal permeable barriers was conducted to investigate phytoextraction of heavy metals by Lolium perenne L. from municipal solid waste compost following EDTA application, as well as to study the effects of L. perenne and permeable barriers on preventing metal from leaching. In columns with barriers, EDTA addition yielded maximum concentrations of Cu, Zn and Pb of 155, 541 and 33.5 mg kg⁻¹ in shoot, respectively. This led to 4.2, 2.1 and 7.4 times higher concentrations of Cu, Zn and Pb compared to treatment with no chelating agent, respectively. In treatments with 10 mmol kg⁻¹ EDTA, the barriers reduced leaching of Cu, Zn and Pb by approximately three times, respectively, resulting in leaching of total initial Cu, Zn and Pb by 27.3%, 25.2% and 28.8%, respectively, after four times’ irrigation. These results indicate that L. perenne and permeable barriers are effective to reduce leaching of heavy metals and minimize the risk of contaminating groundwater in EDTA-enhanced phytoremediation. Thus these findings highlight that turfgrass and permeable barriers can effectively prevent metal leaching.     

The influence of nutritional conditions on metal uptake by the mixotrophic dual symbiosis harboring vent mussel Bathymodiolus azoricus

The vent mussel Bathymodiolus azoricus, host thioautotrophic and methanotrophic bacteria, in their gills and complementary, is able to digest suspended organic matter. But the involvement of nutritional status in metal uptake and storage remains unclear. The influence of B. azoricus physiological condition on its response to the exposure of a mixture of metals in solution is addressed. Mussels from the Menez Gwen field were exposed to 50 μg L^− 1 Cd, plus 25 μg L^− 1 Cu and 100 μg L^− 1 Zn for 24 days. Four conditions were tested: (i) mussels harboring both bacteria but not feed, (ii) harboring only methanotrophic bacteria, (iii) without bacteria but fed during exposure and (iv) without bacteria during starvation. Unexposed mussels under the same conditions were used as controls. Eventual seasonal variations were assessed. Metal levels were quantified in subcellular fractions in gills and digestive gland. Metallothionein levels and condition indices were also quantified. Gill sections were used for fluorescence in situ hybridization (FISH) to assess the temporal distribution of symbiotic associations. Starvation damages metal homeostasis mechanisms and increase the intracellular Zn and MT levels function. There is a clear metallic competition for soluble and insoluble intracellular ligands at each condition. Seasonal variations were observed at metal uptake and storage.     

Nitrogen and phosphorus effect on Typha domingensis Presl. rhizome growth in a matrix of Schoenoplectus americanus (Pers.) Volkart ex Schinz and Keller

In an outdoor mesocosm experiment of 80 weeks, the effect of nitrogen and phosphorus addition was tested on growth of Typha domingensis Presl. rhizomes in a matrix of Schoenoplectus americanus (Pers.) Volkart ex Schinz and Keller, under loading rates of 0.23 gm⁻² d⁻¹ of nitrogen, 0.17 gm⁻² d⁻¹ of P, both nutrient together and control conditions, to assess the potential expansion of T. domingensis in response to nutrient inputs.     

Anaerobic degradation of tetrachlorobisphenol-A in river sediment

This study investigated the anaerobic degradation of tetrachlorobisphenol-A (TCBPA) in sediment samples collected at three sites along the Erren River in southern Taiwan. TCBPA anaerobic degradation half-lives (t_1/2) in the sediment were 12.6, 16.9 and 21.7 d at concentrations of 50, 100, and 250 ??g g⁻¹, respectively. TCBPA (50 ??g g⁻¹) anaerobic degradation half-lives (t_1/2) in the sediment were 10.1, 11.8, 11.0, 11.6, 10.8, 9.1, 8.5, 18.2, 19.3, and 16.1 d by the addition of yeast extract (5 mg l⁻¹), cellulose (0.96 mg l⁻¹), sodium chloride (1%), brij 30 (130 mg l⁻¹), brij 35 (43 mg l⁻¹), rhamnolipid (55 ??M), surfactin (91 ??M), phthalic esters (2 mg l⁻¹), nonylphenol (2 mg l⁻¹), and heavy metals (2 mg l⁻¹), respectively. The degradation rate of TCBPA was enhanced by the addition of yeast extract, cellulose, sodium chloride, brij 30, brij 35, rhamnolipid, or surfactin. However, it was inhibited by the addition of phthalic esters, nonylphenol, or heavy metals. Also noted was the presence of dichlorobisphenol-A and bisphenol-A, two intermediate products resulting from the anaerobic degradation of TCBPA accumulated in the sediments.     

Cytoskeletal and developmental alterations in Ceratophyllum demersum induced by microcystin-LR, a cyanobacterial toxin

The aim of the present work was the investigation of microtubule organization related to developmental processes of Ceratophyllum demersum, a submergent aquatic macrophyte, as affected by microcystin-LR (MCY-LR), a cyanobacterial toxin. We studied the time- and dose-dependent effects of the cyanotoxin in a concentration range of 0.01-20 μg mL⁻¹ (0.01-20.1 μM) at exposure times of 2-16 d. At short term (4 d) of MCY-LR exposure we observed the inhibition of C. demersum shoot tip elongation. This phenomenon was already observed at 0.01 μg mL⁻¹ MCY-LR (reduction of shoot tip length to 56 ± 3.6% of controls) and correlated with the induction of cortical microtubule (CMT) reorientation from transverse to longitudinal known to induce radial expansion of meristematic cells instead of normal elongation. Concomitantly we detected the increase of the percentage of cells in early mitosis in shoot tip meristems, from 1.17 ± 0.2% for controls to 1.93 ± 0.3 at 0.01 μg mL⁻¹ MCY-LR and 6.19 ± 0.5 at 10 μg mL⁻¹ MCY-LR. Cyanotoxin exposure induced the inhibition of general shoot elongation that was more pronounced than inhibition of the increase of leaf whorl number or fresh weight in the treatment period and this was observable at as short as 2-4 d of 2.5 μg mL⁻¹ MCY-LR exposure. This observation further proved that the MCY-LR-induced inhibition of cell elongation is responsible mainly for growth inhibition in C. demersum. Concomitantly with developmental and growth changes MCY-LR decreased protein and chlorophyll content at 16 d of exposure: at 20 μg mL⁻¹ of cyanotoxin, protein content was reduced to 53.3 ± 2.8%, while total chlorophyll content to 46.53 ± 2.7% of controls. This is the first study showing that MCY-LR inhibits the growth of C. demersum through cytoskeletal reorganization. This plant proved to be a powerful model system for toxicological as well as plant cell biology studies.     

Ecophysiological responses of the mangrove Avicennia marina to trace metal contamination

Growth responses of Avicennia marina seedlings to contamination by different concentrations of two essential (Cu, Zn) and two non-essential (Pb, Hg) trace metals were studied under glasshouse conditions. We tested the hypothesis that soil retention and root ultrafiltration would exclude most of the trace metals, and that those that are absorbed and translocated to the shoots would interfere with plant performance and be excreted via leaf salt glands. One-month-old seedlings were subjected to Cu, Zn, Pb and Hg at concentrations of 0, 40, 80, 120 and 160 μg g⁻¹ sediment for 12 months in a randomized complete block design (n = 6). Photosynthesis was measured at the end of 12 months of trace metal exposure with a portable gas exchange system and chlorophyll fluorescence with a pulse-modulated fluorometer. After morphometric measurements, plants were harvested and analyzed for Cu, Zn, Pb and Hg by atomic absorption spectroscopy. Total dry biomass decreased with increasing trace metal concentration for all metals. In the 160 μg g⁻¹ Cu, Zn, Hg and Pb treatments, total biomass was significantly lower than the control value by 43%, 37%, 42% and 40%, respectively. Decreases in plant height and number of leaves followed trends similar to those for total biomass and ranged from 37% to 60%, compared to the controls. Decreases in chlorophyll content in the trace metal treatments ranged from 50% to 58% compared to the control. Carbon dioxide exchange, quantum yield of photosystem II (PSII), electron transport rate (ETR) through PSII and photosynthetic efficiency of PSII (F_v/F_m) were highest in the control treatment and decreased with increasing trace metal concentrations. Decreases in CO₂ exchange in the 160 μg g⁻¹ treatments for all trace metals ranged from 50% to 60%. Concentrations of all trace metals in plant organs increased with increasing metal concentrations and were higher in roots than in shoots, with concentrations of Cu and Zn being considerably higher than those of Hg and Pb. Qualitative elemental analyses and X-ray mapping of crystalline deposits over the glands at the leaf surfaces indicated that Cu and Zn were excreted from the salt glands, while Hg and Pb were absent, at least being below the limits of detection. These results demonstrate that growth processes are sensitive to trace metals and therefore can be considered as a cost of metal tolerance, but salt glands of this mangrove species do contribute eliminating at least part of physiologically essential trace metals if taken up in excess.     

Effect of nutrient limitation and two-stage continuous fermentor design on productivities during "Clostridium ragsdalei" syngas fermentation

The effect of three limiting nutrients, calcium pantothenate, vitamin B₁₂ and cobalt chloride (CoCl₂), on syngas fermentation using “Clostridium ragsdalei” was determined using serum bottle fermentation studies. Significant results from the bottle studies were translated into single- and two-stage continuous fermentor designs. Studies indicated that three-way interactions between the three limiting nutrients, and two-way interactions between vitamin B₁₂ and CoCl₂ had a significant positive effect on ethanol and acetic acid formation. In general, ethanol and acetic acid production ceased at the end of 9 days corresponding to the production of 2.01 and 1.95 g L⁻¹ for the above interactions. Reactor studies indicated the three-way nutrient limitation in two-stage fermentor showed improved acetic acid (17.51 g g⁻¹ cells) and ethanol (14.74 g g⁻¹ cells) yield compared to treatments in single-stage fermentors. These results further support the hypothesis that it is possible to modulate the product formation by limiting key nutrients during C. ragsdalei syngas fermentation.     

Inoculation of Rhizobium (VR-1 and VA-1) induces an increasing growth and metal accumulation potential in Vigna radiata and Vigna angularis L. growing under fly-ash

Fly-ash-tolerant Rhizobium strains were isolated from plants grown in fly-ash-contaminated soil, axenically under laboratory conditions. Saplings of both plants were raised in N₂-free Jenson medium and inoculated with 2.6 × 10⁸ cell ml⁻¹ and 5.2 × 10⁸ cell ml⁻¹ of culture after 10 d of growth. Plants were transferred into 100% fly-ash under natural condition. Rhizobium-inoculated plants grown on 100% fly-ash showed marked increase in relation to root-shoot length, biomass yield, photosynthetic pigment, protein content and nodulation frequency compared to uninoculated plant grown in control (100% fly-ash). Inoculation of fly-ash-tolerant Rhizobium increased the accumulation of Fe, Zn, Cu Cd and Cr in different tissues vis-à-vis enhanced translocation of metals to the aboveground part of plant. Although inoculation of fly-ash-tolerant Rhizobium strains (VR-1 and VA-1) enhanced the translocation of more Fe to shoot parts, nevertheless, the amount of Rhizobium inoculants supplied to the plant was found to be very important since it has a positive role in increasing plant growth through increased N₂ supply via nitrogenase activity. Results suggest that an integrated approach employing biotechnological means and inoculation of plants with host-specific fly-ash-tolerant Rhizobium strain may prove a stimulus to a fly-ash management programme.     

Cadmium accumulation in Atriplex halimus subsp. schweinfurthii and its influence on growth,proline, root hydraulic conductivity and nutrient uptake

Atriplex halimus subsp. schweinfurthii is a newly found cadmium (Cd)-hyperaccumulator, but there have been no detailed studies on its physiological responses when Cd is hyperaccumulated. A. halimus was grown in hydroponic conditions to investigate the effect of cadmium chloride (CdCl₂) on growth, water status, leaf chlorophyll concentration, proline and Cd accumulation. Treatments were prepared by adding 0, 50, 100, 200 and 400 μM CdCl₂ to the nutrient medium. Plant growth was significantly affected at high-Cd treatments. Increased CdCl₂ decreased chlorophyll concentration, transpiration and root hydraulic conductivity (L₀). Hence water flux had only a little effect on the uptake of Cd in A. halimus seedlings. In contrast, proline content increased with increasing CdCl₂ concentration. Plants accumulated substantial amount of Cd in different plant parts (shoot and root). Most of the Cd taken up was retained in roots (606.51 μg g⁻¹DW after 15 d at 400 μM CdCl₂). The addition of Cd in the culture medium affected calcium (Ca) and potassium (K) nutrition in both shoot and root. A. halimus provides a new plant resource for exploring the mechanism of Cd hyperaccumulation and has potential for use in the phytostabilization of Cd-contaminated salt soils.     

Effects of eutrophic water flooding on nitrate concentrations in mine wastes

Salt marshes near urban, industrial and mining areas are often affected both by heavy metals and by eutrophic water. The aim of this study was to assess and evaluate the main processes involved in the decrease of nitrate concentration in pore water of mine wastes flooded with eutrophic water, considering the presence or absence of plant rhizhosphere. Basic (pH ∼ 7.8) carbonated loam mine wastes and free-carbonated acidic (pH ∼ 6.2) sandy-loam mine wastes were collected from polluted coastal salt marshes of SE Spain which regularly receive nutrient-enriched water. The wastes were put in pots and flooded for 15 weeks with eutrophic water (dissolved organic carbon ∼26 mg L⁻¹, PO₄³⁻ ∼23 mg L⁻¹, NO₃⁻ ∼180 mg L⁻¹). Three treatments were assayed for each type of waste: pots with Sarcocornia fruticosa, pots with Phragmites australis and unvegetated pots. Soluble organic carbon, nitrate, soluble Cd, Pb and Zn, pH and Eh were monitored. But the 2nd day of flooding, nitrate concentrations had decreased between 70% and 90% (equivalent to 1.01-1.12 g N-NO₃⁻ m⁻² day⁻¹) with respect to the content in the water used for flooding, except in unvegetated pots with acidic wastes. Denitrification was the main mechanism associated with the removal of nitrate. The role of vegetation in improving the rhizospheric environment was relevant in the acidic wastes because higher sand content, lower pH and higher soluble metal concentrations might strongly hinder microbial activity Hence, revegetation of salt marshes polluted by acidic sandy mining wastes might improve the capacity of this type of environment to act as a green filter against excessive nitrate contents flowing through them.     

Inter-population variability of leaf morpho-anatomical and terpenoid patterns of Pistacia atlantica Desf. ssp. atlantica growing along an aridity gradient in Algeria

Three Algerian populations of female Pistacia atlantica shrubs were investigated in order to check whether their terpenoid contents and morpho-anatomical parameters may characterize the infraspecific variability. The populations were sampled along a gradient of increasing aridity from the Atlas mountains into the northwestern Central Sahara.As evidenced by Scanning Electron Microscopy, tufted hairs could be found only on seedling leaves from the low aridity site as a population-specific trait preserved also in culture. Under common garden cultivation seedlings of the high aridity site showed a three times higher density of glandular trichomes compared to the low aridity site. Increased aridity resulted also in reduction of leaf sizes while their thickness increased. Palisade parenchyma thickness also increases with aridity, being the best variable that discriminates the three populations of P. atlantica.Analysis of terpenoids from the leaves carried out by GC-MS reveals the presence of 65 compounds. The major compounds identified were spathulenol (23 μg g⁻¹ dw), α-pinene (10 μg g⁻¹ dw), verbenone (7 μg g⁻¹ dw) and β-pinene (6 μg g⁻¹ dw) in leaves from the low aridity site; spathulenol (73 μg g⁻¹ dw), α-pinene (25 μg g⁻¹ dw), β-pinene (18 μg g⁻¹ dw) and γ-amorphene (16 μg g⁻¹ dw) in those from medium aridity and spathulenol (114 μg g⁻¹ dw), α-pinene (49 μg g⁻¹ dw), germacrene D (29 μg g⁻¹ dw) and camphene (23 μg g⁻¹ dw) in leaves from the high aridity site. Terpene concentrations increased with the degree of aridity: the highest mean concentration of monoterpenes (136 μg g⁻¹ dw), sesquiterpenes (290 μg g⁻¹ dw) and total terpenes (427 μg g⁻¹ dw) were observed in the highest arid site and are, respectively, 3-, 5- and 4-fold higher compared to the lower arid site. Spathulenol and α-pinene can be taken as chemical markers of aridity. Drought discriminating compounds in low, but detectable concentrations are δ-cadinene and β-copaene. The functional roles of the terpenoids found in P. atlantica leaves and principles of their biosynthesis are discussed with emphasis on the mechanisms of plant resistance to drought conditions.     

In silico optimization and low structured kinetic model of poly[(R)-3-hydroxybutyrate] synthesis by Cupriavidus necator DSM 545 by fed-batch cultivation on glycerol

Glycerol was utilized by Cupriavidus necator DSM 545 for production of poly-3-hydroxybutyrate (PHB) in fed-batch fermentation. Maximal specific growth rates (0.12 and 0.3 h⁻¹) and maximal specific non-growth PHB production rate (0.16 g g⁻¹ h⁻¹) were determined from two experiments (inocula from exponential and stationary phase). Saturation constants for nitrogen (0.107 and 0.016 g L⁻¹), glycerol (0.05 g L⁻¹), non-growth related PHB synthesis (0.011 g L⁻¹) and nitrogen/PHB related inhibition constant (0.405 g L⁻¹), were estimated. Five relations for specific growth rate were tested using mathematical models. In silico performed optimization procedures (varied glycerol/nitrogen ratio and feeding) has resulted in a PHB content of 70.9%, shorter cultivation time (23 h) and better PHB yield (0.347 g g⁻¹). Initial concentration of biomass 16.8 g L⁻¹ and glycerol concentration in broth between 3 and 5 g L⁻¹ were decisive factors for increasing of productivity.     

Synthesis and characterization of a molecularly imprinted polymer and its application as SPE enrichment sorbent for determination of trace methimazole in pig samples using HPLC-UV

A novel molecularly imprinted polymer that could be applied as enrichment sorbent was prepared using methimazole (MMZ) as the template molecule, methacrylic acid as functional monomer, ethylene glycol dimethacrylate as cross-linker. Though evaluated by static, kinetic and competitive adsorption tests, the polymer exhibited high adsorption capacity, fast kinetics and good selective ability. A method for determination of trace MMZ was developed using this polymer as enrichment sorbent coupled with high performance liquid chromatography focusing on complex biological matrices. Under the optimum experimental conditions, the MMZ standard is linear within the concentration range studied, that is, from 0.5 μg L⁻¹ to 150 μg L⁻¹ (r² = 0.9941). Lower limits of detection (LOD, at S/N = 3) and quantification (LOQ, at S/N = 10) in pig samples were 0.63 μg kg⁻¹ and 2.10 μg kg⁻¹ for kidney, 0.51 μg kg⁻¹ and 1.70 μg kg⁻¹ for liver, 0.56 μg kg⁻¹ and 1.86 μg kg⁻¹ for muscle, respectively. Recoveries and relative standard deviation (RSD, n = 9) values for precision in the developed method were from 71.14% to 88.41% and from 2.53% to 6.18%.     

Cultivation of microalgae for oil production with a cultivation strategy of urea limitation

The microalgae, Chlorella sp., were cultivated in various culture modes to assess biomass and lipid productivity in this study. In the batch mode, the biomass concentrations and lipid content of Chlorella sp. cultivated in a medium containing 0.025–0.200 g L⁻¹ urea were 0.464–2.027 g L⁻¹ and 0.661–0.326 g g⁻¹, respectively. The maximum lipid productivity of 0.124 g d⁻¹ L⁻¹ occurred in a medium containing 0.100 g L⁻¹ urea. In the fed-batch cultivation, the highest lipid content was obtained by feeding 0.025 g L⁻¹ of urea during the stationary phase, but the lipid productivity was not significantly increased. However, a semi-continuous process was carried out by harvesting the culture and renewing urea at 0.025 g L⁻¹ each time when the cultivation achieved the early stationary phase. The maximum lipid productivity of 0.139 g d⁻¹ L⁻¹ in the semi-continuous culture was highest in comparison with those in the batch and fed-batch cultivations.     

Development of chemically defined media supporting high cell density growth of Ketogulonicigenium vulgare and Bacillus megaterium

The immediate precursor of L-ascorbic acid, or vitamin C, is 2-keto-l-gulonic acid (2-KLG). This is commonly produced commercially by Ketogulonicigenium vulgare and Bacillus megaterium, using corn steep liquor powder (CSLP) as an organic nitrogen source. In this study, the effects of the individual CSLP components (amino acids, vitamins, and metal elements) on 2-KLG production were evaluated, with the aim of developing a complete, chemically defined medium for 2-KLG production. Forty components of CSLP were analyzed, and key components were correlated to biomass, 2-KLG productivity, and consumption rate of L-sorbose. Glycine had the greatest effect, followed by serine, biotin, proline, nicotinic acid, and threonine. The combination of 0.28 g L⁻¹ serine, 0.36 g L⁻¹glycine, 0.18 g L⁻¹ threonine, 0.28 g L⁻¹proline, 0.19 g L⁻¹nicotinic acid, and 0.62 mg L⁻¹biotin in a chemically defined medium produced the highest maximum biomass concentration (4.2 × 10⁹ cfu mL⁻¹), 2-KLG concentration (58 g L⁻¹), and yield (0.76 g g⁻¹) after culturing for 28 h.     

Interaction of Cd and Zn during uptake and loss in the polychaete Capitella capitata: Whole body and subcellular perspectives

The interaction between Cd and Zn in aquatic organisms is known to be highly variable. The purpose of this study was to use a subcellular compartmentalization approach to examine Cd and Zn interactions in the deposit-feeding polychaete Capitella capitata (sp. I). Laboratory-reared C. capitata were co-exposed to Cd (background or 50 μg Cd l^− 1) and Zn (background or 86 μg Zn l^− 1) with ¹⁰⁹Cd and ⁶⁵Zn as radiotracers for 1 week. After the 1-week uptake period, subsets of worms were allowed to depurate accumulated metals for an additional 1 week. Worms from both phases (uptake and loss) were then subjected to subcellular fractionation to determine the compartmentalization of metals as metal-sensitive fractions [MSF — organelles and heat-denaturable proteins (HDP)] and biologically detoxified metals [BDM — heat-stable proteins (HSP) and metal-rich granules (MRG)]. Uptake and loss of Cd and Zn in C. capitata at the whole body level were similar at bkgd-Cd/bkgd-Zn, with worms depurating the majority of accumulated metal (∼ 75% Cd and ∼ 64% Zn). When exposure of Zn or Cd was increased (bkgd-Cd/86-Zn; bkgd-Zn/50-Cd), uptake of background levels of Cd or Zn, respectively, was suppressed by ∼ 50%. These accumulated metals, however, were retained during the loss phase resulting in ∼ 40-50% greater Cd and Zn whole body tissue burdens than those of bkgd-Cd/bkgd-Zn worms. Beyond exhibiting similar patterns of uptake and loss at the whole body level, Cd and Zn behaved similarly at the subcellular level. Under background levels (bkgd-Cd/bkgd-Zn), after uptake, worms partitioned a majority of Cd (∼ 65%) and Zn (∼ 55%) to the HSP and organelles fractions. The HDP and MRG fractions contained less than ∼ 6% of both metals. Following depuration, at bkgd-Cd/bkgd-Zn, Cd and Zn were lost from all subcellular fractions; loss from HSP was the greatest contributor to whole body loss. When exposed to elevated concentrations of Zn or Cd, the suppression in uptake of bkgd-Cd or bkgd-Zn observed in whole body uptake was largely due to suppressions in the storage of Cd and Zn to HSP. These results suggest that Cd-Zn interactions reduce partitioning of both Cd and Zn to HSP, indicating that metal-binding proteins such as metallothioneins play a key role in these interactions.     

Modeling of biomass production by Spirulinaplatensis as function of phosphate concentrations and pH regimes

Batch cultivations were performed to evaluate the influence of phosphate concentrations (0.25, 0.5, 0.75, and 1.0 g L⁻¹) for pH regimes (9.5, 10.0, and 10.5) on the biomass production by Spirulina platensis. The best condition for cell growth (3.099 g L⁻¹) was found at 0.5 g L⁻¹ phosphate and pH value of 10.0. Cultivation time, phosphate, and pH caused to increase significantly (p < 0.01) in biomass production by S. platensis. Lag time was observed up to 4 h. After then, biomass production increased sharply (p < 0.01) from 0.020 g L⁻¹ to 2.063, 2.213, 1.532, and 0.797 g L⁻¹ at 0.25, 0.5, 0.75, and 1.0 g L⁻¹ phosphate values, respectively. Modified Gompertz model could be regarded as sufficient to describe the biomass production by S. platensis with high determination coefficients and low sum of square value indicated that. Biological parameters for biomass production were successfully predicted by modified Gompertz model.     

Lactic acid production by Lactobacillus sp. RKY2 in a cell-recycle continuous fermentation using lignocellulosic hydrolyzates as inexpensive raw materials

Continuous lactic acid fermentations were conducted using lignocellulosic hydrolyzates and corn steep liquor as inexpensive raw materials. Lactic acid concentrations decreased with increases in the dilution rate, whereas the residual substrate concentrations increased. However, lactic acid yields were maintained at more than 0.90 g g⁻¹ over all cases experimented. The cell-recycle cultivation system exerted positive effects on fermentation efficiency, including volumetric productivity, which is attributable to the retention of cells in the bioreactor. The cell-recycle continuous fermentation of lignocellulosic hydrolyzates yielded a lactic acid productivity of 6.7 g l⁻¹ h⁻¹ for a dilution rate of 0.16 h⁻¹ using 30 g l⁻¹ of corn steep liquor and 1.5 g l⁻¹ of yeast extract as nutrients. The productivity (6.7 g l⁻¹ h⁻¹) acquired by the cell-recycle continuous fermentation of lignocellulosic hydrolyzates was 1.6 times higher than the lactic acid productivity yielded in the continuous fermentation without cell-recycle system.     

Multi-objective optimization of glycopeptide antibiotic production in batch and fed batch processes

Fermentation optimization involves potentially conflicting multiple objectives such as product concentration and production media cost. Simultaneous optimization of these objectives would result in a multiobjective optimization problem, which is characterized by a set of multiple solutions, knows as pareto optimal solutions. These solutions gives flexibility in evaluating the trade-offs and selecting the most suitable operating policy. Here, ε-constraint approach was used to generate the pareto solutions for two objectives: product concentration and product per unit cost of media, for batch and fed batch operations using process model for Amycolatopsis balhimycina, a glycopeptide antibiotic producer. This resulted in a set of several pareto optimal solutions with the two objectives ranging from (0.75 g l⁻¹, 3.97 g $^-1) to (0.44 g l⁻¹, 5.19 g $^-1) for batch and from (1.5 g l⁻¹, 5.46 g $^-1) to (1.1 g l⁻¹, 6.34 g $^-1) for fed batch operations. One pareto solution each for batch and for fed batch mode was experimentally validated.     

3-Phenyllactic acid production by substrate feeding and pH-control in fed-batch fermentation of Lactobacillus sp. SK007

3-Phenyllactic acid (PLA), which is produced by some strains of lactic acid bacteria (LAB), is a known antimicrobial agent with a broad spectrum. Batch and fed-batch fermentation by the strain Lactobacillus sp. SK007 for PLA production have been reported. With batch fermentation without pH-control, PLA production yield was 2.42 g L⁻¹. When fed-batch fermentation by Lactobacillus sp. SK007 was conducted in 3 L initial volume with pH-control at 6.0 and intermittent feeding, which was developed after fermentation for 12 h and every 2 h with 120 mL 100 g L⁻¹ PPA phenylpyruvic acid (PPA) and 50 mL 500 g L⁻¹ glucose each time, PLA production yield reached 17.38 g L⁻¹. The final conversion ratio of PPA to PLA was 51.1%, and the PLA production rate was 0.241 g L⁻¹ h⁻¹. This indicated that PPA was the ideal substrate for PLA fermentation production, and fed-batch fermentation with intermittent PPA feeding and pH-control was an effective approach to improve PLA production yield.