Influence of biofilms on iron and manganese deposition in drinking water distribution systems

Although health risk due to discoloured water is minimal, such water continues to be the source of one of the major complaints received by most water utilities in Australia. Elevated levels of iron (Fe) and/or manganese (Mn) in bulk water are associated with discoloured water incidents. The accumulation of these two elements in distribution systems is believed to be one of the main causes for such elevated levels. An investigation into the contribution of pipe wall biofilms towards Fe and Mn deposition, and discoloured water events is reported in this study. Eight laboratory-scale reactors were operated to test four different conditions in duplicate. Four reactors were exposed to low Fe (0.05 mg l(-1)) and Mn (0.02 mg l(-1)) concentrations and the remaining four were exposed to a higher (0.3 and 0.4 mg l(-1) for Fe and Mn, respectively) concentration. Two of the four reactors which received low and high Fe and Mn concentrations were chlorinated (3.0 mg l(-1) of chlorine). The biological activity (measured in terms of ATP) on the glass rings in these reactors was very low (～1.5 ng cm(-2) ring). Higher concentrations of Fe and Mn in bulk water and active biofilms resulted in increased deposition of Fe and Mn on the glass rings. Moreover, with an increase in biological activity, an increase in Fe and Mn deposition was observed. The observations in the laboratory-scale experiments were in line with the results of field observations that were carried out using biofilm monitors. The field data additionally demonstrated the effect of seasons, where increased biofilm activities observed on pipe wall biofilms during late summer and early autumn were found to be associated with increased deposition of Fe and Mn. In contrast, during the cooler months, biofilm activities were a magnitude lower and the deposited metal concentrations were also significantly less (ie a drop of 68% for Fe and 86% for Mn). Based on the laboratory-scale investigations, detachment of pipe wall biofilms due to cell death or flow dynamics could release the entrapped Fe and Mn into the bulk water, which could lead to a discoloured water event. Hence, managing biofilm growth on drinking water pipelines should be considered by water utilities to minimize accumulation of Fe and Mn in distribution networks.     

Multi-species biofilms defined from drinking water microorganisms provide increased protection against chlorine disinfection

A model biofilm, formed of multiple species from environmental drinking water, including opportunistic pathogens, was created to explore the tolerance of multi-species biofilms to chlorine levels typical of water-distribution systems. All species, when grown planktonically, were killed by concentrations of chlorine within the World Health Organization guidelines (0.2–5.0?mg?l^?1). Higher concentrations (1.6–40-fold) of chlorine were required to eradicate biofilm populations of these strains, ～70% of biofilms tested were not eradicated by 5.0?mg?l^?1 chlorine. Pathogenic bacteria within the model multi-species biofilms had an even more substantial increase in chlorine tolerance; on average ～700–1100?mg?l^?1 chlorine was required to eliminate pathogens from the biofilm, 50–300-fold higher than for biofilms comprising single species. Confocal laser scanning microscopy of biofilms showed distinct 3D structures and multiple cell morphologies and arrangements. Overall, this study showed a substantial increase in the chlorine tolerance of individual species with co-colonization in a multi-species biofilm that was far beyond that expected as a result of biofilm growth on its own.     

Bioremediation of metal contamination in the Plankenburg River,Western Cape,South Africa

Three bioreactors (two laboratory-scale and one on-site) were evaluated for their efficiency to reduce metal concentrations in water collected from the Plankenburg River, South Africa. Water (bioreactors one, two and on-site) and bioballs (bioreactors two and on-site) collected throughout the study periods were digested and analysed using Inductively Coupled Plasma Atomic Emission Spectrometry (ICP-AES). Aluminium (Al), nickel (Ni), and zinc (Zn) concentrations decreased from 0.41 mg l^?1 to 0.06 mg l^?1 (85%), 0.2 mg l^?1 to 0.07 mg l^?1 (65%) and 75 mg l^?1 to 0.02 mg l^?1 (97%), respectively (bioreactor one). Aluminium [(1.55–0.38 mg l^?1 (75%)], copper (Cu) [57% (from 0.33 mg l^?1 to 0.14 mg l^?1)], iron (Fe) [71.99–40.4 mg l^?1 (44%)] and manganese (Mn) [57% (0.07–0.03 mg l^?1)] concentrations also decreased in the water samples from bioreactor two. In the on-site, six-tank bioreactor system, concentrations for Fe, Cu, Mn and Ni decreased, while Zn and Al concentrations increased. The concentrations recorded in biofilm samples were higher than the corresponding water samples. The bioballs employed in the bioreactor were thus shown to be efficient attachment surfaces for biofilm development and subsequent metal accumulation. Potentially metal-tolerant organisms (Pseudomonas sp., Sphingomonas sp., and Bacillus sp.) were also identified using phylogeny.     

The influence of chlorination timing and concentration on microbial communities in labyrinth channels: implications for biofilm removal

Chlorination is an effective method to control biofilm formation in enclosed pipelines. To date, very little is known about how to control biofilms at the mesoscale in complex pipelines through chlorination. In this study, the dynamic of microbial communities was examined under different residual chlorine concentrations on the biofilms attached to labyrinth channels for drip irrigation using reclaimed water. The results indicated that the microbial phospholipid fatty acids, extracellular polymeric substances, microbial dynamics, and the ace and Shannon microbial diversity indices showed a gradual decrease after chlorination. However, chlorination increased microbial activity by 0.5–19.2%. The increase in the relative abundances of chloride-resistant bacteria (Acinetobacter and Thermomonas) could lead to a potential risk of chlorine resistance. Thus, keeping a low chlorine concentration (0.83?mg l^?1 for 3?h) is effective for controlling biofilm formation in the labyrinth channels.     

Influence of surface copper content on Stenotrophomonas maltophilia biofilm control using chlorine and mechanical stress

Abstract

This work aimed to evaluate the action of materials with different copper content (0, 57, 96 and 100%) on biofilm formation and control by chlorination and mechanical stress. Stenotrophomonas maltophilia isolated from drinking water was used as a model microorganism and biofilms were developed in a rotating cylinder reactor using realism-based shear stress conditions. Biofilms were characterized phenotypically and exposed to three control strategies: 10?mg l^?1 of free chlorine for 10?min, an increased shear stress (a fluid velocity of 1.5?m s^?1 for 30s), and a combination of both treatments. These shock treatments were not effective in biofilm control. The benefits from the use of copper surfaces was found essentially in reducing the numbers of non-damaged cells. Copper materials demonstrated better performance in biofilm prevention than chlorine. In general, copper alloys may have a positive public health impact by reducing the number of non-damaged cells in the water delivered after chlorine exposure.     

Influence of detachment,substrate loading and reactor scale on the formation of biofilms in airlift reactors

 For a stable and reliable operation of the biofilm airlift suspension reactor (BAS reactor) means to control biomass concentration, biofilm thickness and biofilm morphology are required. For this reason, the influence of applied detachment forces and surface substrate loading on the formation of heterotrophic biofilms in laboratory-scale BAS reactors was studied. Detachment forces were altered by variation of the initial bare carrier concentration or the superficial air velocity. In addition, the dynamics of biofilm formation during start-up of a full scale BAS reactor (300 m³) was monitored and compared with the laboratory-scale start-up (3 l). This study shows that the biofilm morphology and strength were influenced to a large extent by the surface substrate loading and applied detachment forces. A moderate surface substrate loading and a high detachment force yielded smooth and strong biofilms. The combination of a high surface substrate loading and low detachment forces did lead to rough biofilms, but did not lead to the expected high amount of biomass on the carrier, apparently because of the formation of weaker biofilms. The strength of the bio-films appeared to be related to the detachment forces applied during biofilm formation, in combination with the surface substrate loading. The biofilm morphology and biomass on carrier in the BAS reactor can be controlled using the carrier concentration, substrate loading rate and the superficial air velocity as parameters. The dynamics of biofilm formation during the start-up of a full-scale BAS reactor proved to be similar to heterotrophic biofilm formation in laboratory-scale reactors. This indicates that a model system on the laboratory scale can successfully be applied to predict dynamic phenomena in the full-scale reactor. Received: 31 March 1995/Received revision: 11 August 1995/Accepted: 22 August 1995     

Assessment of an anti-scale low-frequency electromagnetic field device on drinking water biofilms

Abstract

Low intensity and very low-frequency electromagnetic fields (EMF) used for preventing scaling in water distribution systems were tested for the first time for their potential impact on drinking water biofilms. The assays were carried out in laboratory-scale flow-through reactors that mimic water distribution systems. The drinking water biofilms were not directly exposed to the core of the EMF generator and only subjected to waterborne electromagnetic waves. The density and chlorine susceptibility of nascent or mature biofilms grown under exposure to EMF were evaluated in soft and hard water. This EMF treatment was able to modify CaCO₃ crystallization but it did not significantly affect biofilms. Indeed, over all the tested conditions, there was no significant change in cell number, or in the integrity of the cells (membrane, culturability), and no measurable effect of chlorine on the biofilm.     

Drinking water biofilm assessment of total and culturable bacteria under different operating conditions

Abstract

Monitoring of biofilms subjected to different operating conditions was performed using a flow cell system. The system was fed by chlorine-free tap water, with and without added nutrients (0.5 mg l^?1 carbon, 0.1 mg l^?1 nitrogen and 0.01 mg l^?1 phosphorus), and biofilms were grown on polyvinyl chloride (PVC) and stainless steel (SS) coupons, both in laminar and turbulent flow. The parameters analysed were culturable cells, using R2A, and total bacteria, which was assessed using the 4,6-diamino-2-phenylindole (DAPI) staining method. The impact of the different operating conditions in the studied parameters was established using Multivariate Analysis of Variance (MANOVA). From the most relevant to the least relevant factor, the total and culturable bacteria in biofilms increased due to the addition of nutrients to water (F = 20.005; p < 0.001); the use of turbulent (Re = 11000) instead of laminar (Re = 2000) hydrodynamic flows (F = 9.173; p < 0.001); and the use of PVC instead of SS as the support material (F = 2.848; p = 0.060). Interactions between these conditions, namely between surface and flow (F = 8.235; p < 0.001) and also flow and nutrients (F = 5.498; p < 0.05) have also proved to significantly influence biofilm formation. This work highlights the need for a deeper understanding of how the large spectrum of conditions interact and affect biofilm formation potential and accumulation with the final purpose of predicting the total and culturable bacteria attached to real drinking water distribution pipes based on the system characteristics.     

A biofilm model developed to investigate survival and disinfection of Mycobacterium mucogenicum in potable water

Water in healthcare environments can be a source for healthcare-associated infections (HAI). However, information on the exposure risk to opportunistic pathogens in potable water distribution systems (PWDS) is lacking. Laboratory studies characterizing the interaction of opportunistic pathogens with biofilms are needed to understand their role in water systems within healthcare facilities. A stable, repeatable, PWDS multi-species biofilm model comprising Sphingomonas paucimobilis, Methylobacterium sp., Delftia acidovorans, and Mycobacterium mucogenicum was developed in the CDC Biofilm Reactor (CBR), reaching 6 log₁₀ CFU cm^?2 within 6 days. The model was used to investigate the interaction of the opportunistic pathogen M. mucogenicum with the other species, and to determine the efficacy of monochloramine (NH₂Cl) as a disinfectant against 2-week-old biofilms. Addition of 1 or 2 mg l^?1 NH₂Cl resulted in the same or an increased log density of viable M. mucogenicum in the biofilm while inactivating some of the Proteobacteria. Although M. mucogenicum preferentially resided in the biofilm, NH₂Cl exposure caused release of viable M. mucogenicum from the biofilm into the water. Additional studies with this model should determine if sodium hypochlorite has a comparative effect and if other nontuberculous mycobacteria (NTM) respond to NH₂Cl similarly.     

Chloraminated drinking water does not generate bacterial resistance to antibiotics in Pseudomonas aeruginosa biofilms

Aim: To determine if exposure of Pseudomonas aeruginosa biofilms to chloraminated drinking water can lead to individual bacteria with resistance to antibiotics. Methods and Results: Biofilms of P. aeruginosa PA14 were grown in drinking water in a Kadouri drip‐fed reactor; the biofilms were treated with either 0·5 mg l^‐1 or 1·0 mg l^‐1 of chloramine for 15 or 21 days; control biofilms were grown in water without chloramine. Fewer isolates with antibiotic resistance were obtained from the chloramine‐treated biofilms as compared to the control. Minimum inhibitory concentrations (MIC) for selected antibiotic‐resistant isolates were determined using ciprofloxacin, tobramycin, gentamicin, rifampicin and chloramphenicol. All of the isolates tested had increased resistance over the wildtype to ciprofloxacin, rifampicin and chloramphenicol, but were not resistant to tobramycin or gentamicin. Conclusions: Under these test conditions, there was no detectable increase in antibiotic resistance in P. aeruginosa exposed as biofilms to disinfectant residues in chloraminated drinking water. Significance and Impact of the study: Chloramine in drinking water, while unable to kill biofilm bacteria, does not increase the potential of P. aeruginosa to become resistant to antibiotics.     

Impact of oxygen mass transfer on nitrification reactions in suspended carrier reactor biofilms

Biofilm-internal and external mass transfer resistance was investigated in laboratory-scale nitrifying suspended carrier reactors (SCR), demonstrating the importance of these factors for these increasingly popular reactor systems. Controlled respirometric experiments revealed that oxygen mass transfer resistance regulated the process performance up to a DO concentration of 20 mg L^?1. External mass transfer exerts significant control over the overall reaction rate, thus biofilm models must adequately account for this resistance. Whilst carrier type and characteristics have some influence, biofilm structure seems primarily responsible for differences in mass transfer and nitrification performance. Heterogeneous biofilms grown under high ammonium loadings had much greater area-specific rates than the gel-like biofilms sourced from low loaded systems.Being a mass-transfer controlled process, the overall reaction rate of these SCR systems could be immediately increased by elevating the DO above normal operating levels (up to 20 mg L^?1). Long-term oxygen deficiency in the lower biofilm sections does not negatively affect the biomass activity.     

Degradation of methicillin-resistant Staphylococcus aureus biofilms using a chimeric lysin

Methicillin-resistant Staphylococcus aureus (MRSA) is responsible for a large number of chronic infections due to its ability to form robust biofilms. Herein, the authors evaluated the anti-biofilm activity of a Staphylococcus specific chimeric lysin ClyH on MRSA biofilms. ClyH is known to be active against planktonic MRSA cells in vitro and in vivo. The minimum concentrations for biofilm eradication (MCBE) of ClyH were 6.2–50?mg?l^?1, much lower than those of antibiotics. Scanning electron microscope (SEM) analysis revealed that ClyH eliminated MRSA biofilms through cell lytic activity in a time-dependent manner. Viable plate counts and kinetic analysis demonstrated that biofilms of different ages displayed varying susceptibility to ClyH. Together with previously demonstrated in vivo efficacy of ClyH against MRSA, the degradation efficacy against biofilms of different ages indicates that ClyH could be used to remove MRSA biofilms in vivo.     

New insight into the effects of Ca(II) on cake layer structure in submerged membrane bioreactors

The effects of Ca(II) on the structure of the cake layer in submerged membrane bioreactors (SMBRs) were investigated in this study. Three parallel laboratory-scale SMBRs were operated with synthetic municipal wastewater with three Ca(II) levels (82, 208 and 410?mg?l^?1). As the Ca(II) concentration increased, the sludge floc size increased and the molecular weight of the soluble microbial products (SMP) in the bulk liquid decreased. These observations were attributed to the neutralization and bridging function of Ca(II). Furthermore, Ca(II) addition did not change the thickness of the cake layer, but inhibited the deposition of other elements, such as Al, Si, Mg, and Fe. As a result of Ca(II) addition, the cake layer became less compact and more porous. The interspaces among the flocs in the cake layer helped to reduce the membrane fouling potential.     

Biofouling control using microparticles carrying a biocide

This study presents a new technological approach to minimize the use of antimicrobial (AMB) agents and their deleterious effects, based on the principle of drug-delivery systems whereby the AMB chemicals are transported on microparticles. The efficacy of microparticles carrying the quaternary ammonium compound (QAC), benzyldimethyldodecyl ammonium chloride (BDMDAC), was assessed against Pseudomonas fluorescens in both the planktonic and the biofilm state. The microparticles were prepared using a layer-by-layer (LBL) self-assembly technique. Oppositely charged molecules of polyethyleneimine (PEI), sodium polystyrene sulfonate (PSS), and BDMDAC were assembled on polystyrene (PS) cores. BDMDAC-coated particles were observed by CryoSEM and their composition analyzed by X-ray microanalysis. Zeta potential measurements indicated that changes in surface charge were compatible with a BDMDAC/particle interaction. This biocidal carrier structure had significant stability, verified by the release of only 15% of the BDMDAC when immersed in water for 18 months. Biocidal carrier activity was evaluated by determining the survival ratio of P. fluorescens planktonic and biofilm cells after different exposure periods to BDMDAC-coated particles. Tests with biofilm cells were also performed with the free QAC. An efficient AMB effect (minimum bactericidal concentration) against suspended cells was found for a concentration of 9.2 mg l^?1 of BDMDAC on coated particles after incubation for 30 min and 6.5 mg l^?1 of BDMDAC on coated particles after 60 min. Exposure of biofilms to PS-PEI/PSS/BDMDAC (0.87 mg l^?1) resulted in a decrease in viability of 60.5% and 66.5% of the total biofilm population for 30 and 60 min exposure times, respectively. Exposure for 60 min to 6.33 mg l^?1 and 11.75 mg l^?1 of BDMDAC in PS-PEI/PSS/BDMDAC particles promoted inactivation of 80.6% and 87.2% of the total population, respectively. The AMB effects obtained with the application of free BDMDAC were statistically similar to those promoted by the application of BDMDAC coated particles. The overall results indicate that this novel AMB strategy has potential for the control of microbial growth of planktonic cells and biofouling. Moreover, the technique allows the reuse of AMB molecules and consequently reduces the environmental risks associated with excessive use of AMB agents, thereby providing real benefits to public health.     

Quantification of viable biomass in biofilm reactors by extractable lipid phosphate

 Lipid phosphate, which is a measure of viable biomass, was determined using biofilm samples from three different laboratory-scale reactors. The analysis procedure proposed in the literature was modified and tested for suitability in experiments with biofilm reactors. The microbial contents of the biofilms studied are compared in three types of reactor. Received: 2 November 1994/Accepted: 23 January 1995     

Effects of chelating agent and environmental stresses on microbial biofilms: relevance to clinical microbiology

Aims: To determine the effect of pH, temperature, desiccation, ethylenediaminetetraacetic acid (EDTA) and desferrioxamine B (DFO) on Panton‐Valentine leukocidin‐positive community acquired methicillin‐susceptible Staphylococcus aureus (PVL +ve CA‐MSSA) biofilm formation. Methods and Results: Biofilms from PVL +ve CA‐MSSA (clinical isolate) were subjected to pH, temperature, desiccation, EDTA and DFO. PVL +ve CA‐MSSA were more resistant to pH and heat than their planktonic equivalents. Desiccation studies demonstrated that PVL +ve CA‐MSSA biofilms were more refractory to the treatment than planktonic cells. Significant inhibition of PVL +ve CA‐MSSA biofilm formation was observed in the presence of 1 mmol l^?1 EDTA. Low concentrations (2·5 μmol l^?1) of DFO enhanced the growth of PVL +ve CA‐MSSA biofilms. At higher concentrations (1 mmol l^?1), DFO did inhibit the growth but not as much as EDTA. A combination of EDTA and DFO inhibited PVL +ve CA‐MSSA biofilm formation at lower concentrations than either alone. Conclusions: This study demonstrates that PVL +ve CA‐MSSA biofilms are resistant to environmental stress but their growth can inhibited effectively by a mixture of EDTA and DFO. Significance and Impact of the Study: The inhibition of biofilm formation by PVL +ve CA‐MSSA using chelating agents has not been previously reported and provides a practical approach to achieve the disruption of these potentially important biofilms formed by an emerging pathogen.     

Heavy metal concentrations in,and human health risk assessment of,three commercially valuable fish species in the lower Niger River,Nigeria

The concentrations of Fe, Mn, Ni, Pb and V in water, sediment and the gill, liver and muscle tissues of Synodontis resupinatus, Heterotis niloticus and Clarias gariepinus, all commercially important fish species of the lower Niger River, were investigated in 2015. Water, sediment and fish samples were collected for six months and heavy metals were determined using an Atomic Absorption Spectrometer. Fe ranked highest in water and sediment, with concentrations of 2.74 mg l^?1 and 61.60 mg kg^?1, respectively. Metals followed the magnitude of Fe > Mn > Ni > V > Pb in the water and Fe > Mn > V > Ni > Pb in the sediments. Metal concentrations were higher in the tissues of S. resupinatus compared with H. niloticus and C. gariepinus. Fe was also highest in the gills, liver and muscle of the three fish species. Its highest concentration of 132.97 mg kg^?1 dry weight was recorded in the gills of S. resupinatus. Bioconcentration factors of metals ranged from 8.79 for Mn in H. niloticus muscle to 67.99 for Ni in S. resupinatus gills. The fish species studied pose no health risk for all metals studied, because the target hazard quotient was less than 1 and the estimated daily intakes of the metals were below the reference doses.     

Biofilm growth kinetics and nutrient (N/P) adsorption in an urban lake using reclaimed water: A quantitative baseline for ecological health assessment

Reclaimed wastewater reuse represents an effective method for partial resolution of increasing urban water shortages; however, reclaimed water may be characterized by significant contaminant loading, potentially affecting receiving ecosystem (and potentially human) health. The current study examined biofilm growth and nutrient adsorption in Olympic Lake (Beijing), the largest artificial urban lake in the world supplied exclusively by reclaimed wastewater. Findings indicate that solid particulate, extracellular polymeric substance (EPS) and metal oxide (Al, Fe, Mn) constituent masses adhere to a bacterial growth curve during biofilm formation and growth. Peak values were observed after ≈30 days, arrived at dynamic stability after ≈50 days and were affected by growth matrix surface roughness. These findings may be used to inform biofilm cultivation times for future biomonitoring. Increased growth matrix surface roughness (10.0 μm) was associated with more rapid biofilm growth and therefore an increased sensitivity to ecological variation in reclaimed water. Reclaimed water was found to significantly inhibit biofilm nutrient adsorption when compared with a “natural water” background, with elevated levels of metal oxides (Al, Fe, and Mn) and EPS representing the key substances actively influencing biofilm nutrient adsorption in reclaimed water. Results from the current study may be used to provide a quantitative baseline for future studies seeking to assess ecosystem health via monitoring of biofilms in the presence of reclaimed water through an improved quantitative understanding of biofilm kinetics in these conditions.     

Effect of phosphate availability on biofilm formation in cooling towers

Abstract

Phosphate limitation has been suggested as a preventive method against biofilms. P-limited feed water was studied as a preventive strategy against biofouling in cooling towers (CTs). Three pilot-scale open recirculating CTs were operated in parallel for five weeks. RO permeate was fed to the CTs (1) without supplementation (reference), (2) with supplementation by biodegradable carbon (P-limited) and (3) with supplementation of all nutrients (non-P-limited). The P-limited water contained ≤10?µg PO₄ l^?1. Investigating the CT-basins and coupons showed that P-limited water (1) did not prevent biofilm formation and (2) resulted in a higher volume of organic matter per unit of active biomass compared with the other CTs. Exposure to external conditions and cycle of concentration were likely factors that allowed a P concentration sufficient to cause extensive biofouling despite being the limiting compound. In conclusion, phosphate limitation in cooling water is not a suitable strategy for CT biofouling control.     

Influence of temperature on process efficiency and microbial community response during the biological removal of chlorophenols in a packed-bed bioreactor

Two reactors, initially operated at 14 and 23±1°C (RA and RB, respectively), were inoculated with a bacterial consortium enriched and acclimatized to the respective temperatures over 4 months. The biofilms, formed in the reactors, were studied using scanning electron microscopy, cultivation of the biofilm microflora, and physiological analysis of the isolates. Two bacteria able to mineralize chlorophenols under a large range of temperature (10–30°C) were isolated from the biofilm communities of reactors RA and RB and characterized as Alcaligenaceae bacterium R14C4 and Cupriavidus basilensis R25C6, respectively. When temperature was decreased by 10°C, the chlorophenols removal capacity was reduced from 51.6 to 22.8 mg l⁻¹ h⁻¹ in bioreactor RA (from 14 to 4°C) and from 59.3 to 34.7 mg l⁻¹ h⁻¹ in bioreactor RB (from 23±1 to 14°C). Fluorescence in situ hybridization (FISH) of the biofilm communities showed that, in all temperatures tested, the β-proteobacteria were the major bacterial community (35–47%) followed by the γ-proteobacteria (12.0–6.5%). When the temperature was decreased by 10°C, the proportions of γ-proteobacteria and Pseudomonas species increased significantly in both microbial communities.