Improved Cycling Stability of Li[Ni0.90Co0.05Mn0.05]O2 Through Microstructure Modification by Boron Doping for Li‐Ion Batteries

Boron‐doped Li[Ni_0.90Co_0.05Mn_0.05]O₂ cathodes are synthesized by adding B₂O₃ during the lithiation of the hydroxide precursor. Density functional theory confirms that boron doping at a level as low as 1 mol% alters the surface energies to produce a highly textured microstructure that can partially relieve the intrinsic internal strain generated during the deep charging of Li[Ni_0.90Co_0.05Mn_0.05]O₂. The 1 mol% B‐Li[Ni_0.90Co_0.05Mn_0.05]O₂ cathode thus delivers a discharge capacity of 237 mAh g^?1 at 4.3 V, with an outstanding capacity retention of 91% after 100 cycles at 55 °C, which is 15% higher than that of the undoped Li[Ni_0.90Co_0.05Mn_0.05]O₂ cathode. This proposed synthesis strategy demonstrates that an optimal microstructure exists for extending the cycle life of Ni‐rich Li[Ni_1‐x‐yCo_xMn_y]O₂ cathodes that have an inadequate cycling stability in electric vehicle applications and indicates that an optimal microstructure can be achieved through surface energy modification.     

Lithium/Oxygen Incorporation and Microstructural Evolution during Synthesis of Li‐Rich Layered Li[Li0.2Ni0.2Mn0.6]O2 Oxides

As promising cathode materials, the lithium‐excess 3d‐transition‐metal layered oxides can deliver much higher capacities (>250 mAh g^?1 at 0.1 C) than the current commercial layered oxide materials (≈180 mAh g^?1 at 0.1 C) used in lithium ion batteries. Unfortunately, the original formation mechanism of these layered oxides during synthesis is not completely elucidated, that is, how is lithium and oxygen inserted into the matrix structure of the precursor during lithiation reaction? Here, a promising and practical method, a coprecipitation route followed by a microwave heating process, for controllable synthesis of cobalt‐free lithium‐excess layered compounds is reported. A series of the consistent results unambiguously confirms that oxygen atoms are successively incorporated into the precursor obtained by a coprecipitation process to maintain electroneutrality and to provide the coordination sites for inserted Li ions and transition metal cations via a high‐temperature lithiation. It is found that the electrochemical performances of the cathode materials are strongly related to the phase composition and preparation procedure. The monoclinic layered Li[Li_0.2Ni_0.2Mn_0.6]O₂ cathode materials with state‐of‐the‐art electrochemical performance and comparably high discharge capacities of 171 mAh g^?1 at 10 C are obtained by microwave annealing at 750 °C for 2 h.     

Solid‐State Lithium/Selenium–Sulfur Chemistry Enabled via a Robust Solid‐Electrolyte Interphase

Lithium/selenium‐sulfur batteries have recently received considerable attention due to their relatively high specific capacities and high electronic conductivity. Different from the traditional encapsulation strategy for suppressing the shuttle effect, an alternative approach to directly bypass polysulfide/polyselenide formation via rational solid‐electrolyte interphase (SEI) design is demonstrated. It is found that the robust SEI layer that in situ forms during charge/discharge via interplay between rational cathode design and optimal electrolytes could enable solid‐state (de)lithiation chemistry for selenium‐sulfur cathodes. Hence, Se‐doped S_22.2Se/Ketjenblack cathodes can attain a high reversible capacity with minimal shuttle effects during long‐term and high rate cycling. Moreover, the underlying solid‐state (de)lithiation mechanism, as evidenced by in situ ⁷Li NMR and in operando synchrotron X‐ray probes, further extends the optimal sulfur confinement pore size to large mesopores and even macropores that have been long considered as inferior sulfur or selenium host materials, which play a crucial role in developing high volumetric energy density batteries. It is expected that the findings in this study will ignite more efforts to tailor the compositional/structure characteristics of the SEI layers and the related ionic transport across the interface by electrode structure, electrolyte solvent, and electrolyte additive screening.     

Best Practices for Mitigating Irreversible Capacity Loss of Negative Electrodes in Li‐Ion Batteries

Development of high performance lithium‐ion (Li‐ion) power packs is a topic receiving significant attention in research today. Future development of the Li‐ion power packs relies on the development of high capacity and high rate anodes. More specifically, materials undergo either conversion or an alloying mechanism with Li. However, irreversible capacity loss (ICL) is one of the prime issues for this type of negative electrode. Traditional insertion‐type materials also experience ICL, but it is considered negligible. Therefore, eliminating ICL is crucial before the fabrication of practical Li‐ion cells with conventional cathodes such as LiFePO₄, LiMn₂O₄, etc. There are numerous methods for eliminating ICL such as pre‐treating the electrode, usage of stabilized Li metal powder, chemical and electrochemical lithiation, sacrificial salts for both anode and cathode, etc. The research strategies that have been explored are reviewed here in regards to the elimination of ICL from the high capacity anodes as described. Additionally, mitigating ICL observed from the carbonaceous anodes is discussed and compared.     

Atomic Structure of Li2MnO3 after Partial Delithiation and Re‐Lithiation

Li₂MnO₃ is the parent compound of the well‐studied Li‐rich Mn‐based cathode materials xLi₂MnO₃·(1‐x)LiMO₂ for high‐energy‐density Li‐ion batteries. Li₂MnO₃ has a very high theoretical capacity of 458 mA h g^?1 for extracting 2 Li. However, the delithiation and lithiation behaviors and the corresponding structure evolution mechanism in both Li₂MnO₃ and Li‐rich Mn‐based cathode materials are still not very clear. In this research, the atomic structures of Li₂MnO₃ before and after partial delithiation and re‐lithiation are observed with spherical aberration‐corrected scanning transmission electron microscopy (STEM). All atoms in Li₂MnO₃ can be visualized directly in annular bright‐field images. It is confirmed accordingly that the lithium can be extracted from the LiMn₂ planes and some manganese atoms can migrate into the Li layer after electrochemical delithiation. In addition, the manganese atoms can move reversibly in the (001) plane when ca. 18.6% lithium is extracted and 12.4% lithium is re‐inserted. LiMnO₂ domains are also observed in some areas in Li_1.63MnO₃ at the first cycle. As for the position and occupancy of oxygen, no significant difference is found between Li_1.63MnO₃ and Li₂MnO₃.     

High‐Performance All‐Solid‐State Lithium–Sulfur Batteries Enabled by Amorphous Sulfur‐Coated Reduced Graphene Oxide Cathodes

Safety and the polysulfide shuttle reaction are two major challenges for liquid electrolyte lithium–sulfur (Li–S) batteries. Although use of solid‐state electrolytes can overcome these two challenges, it also brings new challenges by increasing the interface resistance and stress/strain. In this work, the interface resistance and stress/strain of sulfur cathodes are significantly reduced by conformal coating ≈2 nm sulfur (S) onto reduced graphene oxide (rGO). An Li–S full cell consisting of an rGO@S‐Li₁₀GeP₂S₁₂‐acetylene black (AB) composite cathode is evaluated. At 60 °C, the all‐solid‐state Li–S cell demonstrates a similar electrochemical performance as in liquid organic electrolyte, with high rate capacities of 1525.6, 1384.5, 1336.3, 903.2, 502.6, and 204.7 mA h g^?1 at 0.05, 0.1, 0.5, 1.0, 2.0, and 5.0 C, respectively. It can maintain a high and reversible capacity of 830 mA h g^?1 at 1.0 C for 750 cycles. The uniform distribution of the rGO@S nanocomposite in the Li₁₀GeP₂S₁₂‐AB matrix generates uniform volume changes during lithiation/delithiation, significantly reducing the stress/strain, thus extending the cycle life. Minimization of the stress/strain of solid cells is the key for a long cycle life of all‐solid‐state Li–S batteries.     

Review on Challenges and Recent Advances in the Electrochemical Performance of High Capacity Li‐ and Mn‐Rich Cathode Materials for Li‐Ion Batteries

Li and Mn‐rich layered oxides, xLi₂MnO₃·(1–x)LiMO₂ (M=Ni, Mn, Co), are promising cathode materials for Li‐ion batteries because of their high specific capacity that can exceed 250 mA h g^?1. However, these materials suffer from high 1^st cycle irreversible capacity, gradual capacity fading, low rate capability, a substantial charge‐discharge voltage hysteresis, and a large average discharge voltage decay during cycling. The latter detrimental phenomenon is ascribed to irreversible structural transformations upon cycling of these cathodes related to potentials ≥4.5 V required for their charging. Transition metal inactivation along with impedance increase and partial layered‐to‐spinel transformation during cycling are possible reasons for the detrimental voltage fade. Doping of Li, Mn‐rich materials by Na, Mg, Al, Fe, Co, Ru, etc. is useful for stabilizing capacity and mitigating the discharge‐voltage decay of xLi₂MnO₃·(1–x)LiMO₂ electrodes. Surface modifications by thin coatings of Al₂O₃, V₂O₅, AlF₃, AlPO₄, etc. or by gas treatment (for instance, by NH₃) can also enhance voltage and capacity stability during cycling. This paper describes the recent literature results and ongoing efforts from our groups to improve the performance of Li, Mn‐rich materials. Focus is also on preparation of cobalt‐free cathodes, which are integrated layered‐spinel materials with high reversible capacity and stable performance.     

Solid‐State Prelithiation Enables High‐Performance Li‐Al‐H Anode for Solid‐State Batteries

Lithium alanates exhibit high theoretical specific capacities and appropriate lithiation/delithiation potentials, but suffer from poor reversibility, cycling stability, and rate capability due to their sluggish kinetics and extensive side reactions. Herein, a novel and facile solid‐state prelithiation approach is proposed to in situ prepare a Li₃AlH₆‐Al nanocomposite from a short‐circuited electrochemical reaction between LiAlH₄ and Li with the help of fast electron and Li‐ion conductors (C and P6₃mc LiBH₄). This nanocomposite consists of dispersive Al nanograins and an amorphous Li₃AlH₆ matrix, which enables superior electrochemical performance in solid‐state cells, as much higher specific capacity (2266 mAh g^?1), Coulombic efficiency (88%), cycling stability (71% retention in the 100th cycle), and rate capability (1429 mAh g^?1 at 1 A g^?1) are achieved. In addition, this nanocomposite works well in the solid‐state full cell with LiCoO₂ cathode, demonstrating its promising application prospects. Mechanism analysis reveals that the dispersive Al nanograins and amorphous Li₃AlH₆ matrix can dramatically enhance the lithiation and delithiation kinetics without side reactions, which is mainly responsible for the excellent overall performance. Moreover, this solid‐state prelithiation approach is general and can also be applied to other Li‐poor electrode materials for further modification of their electrochemical behavior.     

Building Lithiophilic Ion‐Conduction Highways on Garnet‐Type Solid‐State Li+ Conductors

The integration of highly conductive solid‐state electrolytes (SSEs) into solid‐state cells is still a challenge mainly due to the high impedance existing at the electrolyte/electrode interface. Although solid‐state garnet‐based batteries have been successfully assembled with the assistance of an intermediate layer between the garnet and the Li metal anode, the slow discharging/charging rates of the batteries inhibits practical applications, which require much higher power densities. Here, a crystalline sulfonated‐covalent organic framework (COF) thin layer is grown on the garnet surface via a simple solution process. It not only significantly improves the lithiophilicity of garnet electrolytes via the lithiation of the COF layer with molten Li, but also creates effective Li⁺ diffusion “highways” between the garnet and the Li metal anode. As a result, the interfacial impedance of symmetric solid‐state Li cells is significantly decreased and the cells can be operated at high current densities up to 3 mA cm^?2, which is difficult to achieve with current interfacial modification technologies for SSEs. The solid‐state Li‐ion batteries using LiFePO₄ cathodes, Li anodes, and COF‐modified garnet electrolytes thus exhibit a significantly improved rate capability.     

MoN Supported on Graphene as a Bifunctional Interlayer for Advanced Li‐S Batteries

Rational design of effective polysulfide barriers is highly important for high‐performance lithium‐sulfur (Li‐S) batteries. A variety of adsorbents have been applied as interlayers to alleviate the shuttle effect. Nevertheless, the unsuccessful oxidation of Li₂S on interlayers leads to loss of active materials and blocks Li ion transport. In this work, a MoN‐based interlayer sandwiched between the C‐S cathode and the separator is developed. Such an interlayer not only strongly binds lithium polysulfides via Mo‐S bonding but also efficiently accelerates the decomposition of Li₂S. The acceleration mechanism toward Li₂S decomposition is determined to be a combination of contributions of catalytic cleavage of Li‐S bond in Li₂S based on the proposed covalence‐activation mechanism and rapid migration of the produced Li ions. As a result, the C–S cathodes with the as‐developed interlayer manifest a negligible charging potential barrier and outstanding cycling stability with a very low capacity fading rate of 0.023% per cycle during 1500 cycles at 1 C. High areal capacity of 6.02 mAh cm^?2 is achieved for high sulfur loading of 7.0 mg cm^?2 after cycling at 0.1 C. The material and strategy demonstrated in this work can open the door toward developing shuttle suppression interlayers without impairing cathode performance.     

Advanced Energy‐Storage Architectures Composed of Spinel Lithium Metal Oxide Nanocrystal on Carbon Textiles

Current battery technologies are known to suffer from kinetic problems associated with the solid‐state diffusion of Li⁺ in intercalation electrodes materials. Not only the use of nanostructure materials but also the design of electrode architectures can lead to more advanced properties. Here, advanced electrode architectures consisting of carbon textiles conformally covered by Li₄Ti₅O₁₂ nanocrystal are rationally designed and synthesized for lithium ion batteries. The efficient two‐step synthesis involves the growth of ultrathin TiO₂ nanosheets on carbon textiles, and subsequent conversion into spinel Li₄Ti₅O₁₂ through chemical lithiation. Importantly, this novel approach is simple and general, and it is used to successfully produce LiMn₂O₄/carbon composites textiles, one of the leading cathode materials for lithium ion batteries. The resulting 3D textile electrode, with various advantages including the direct electronic pathway to current collector, the easy access of electrolyte ions, the reduced Li⁺/e^? diffusion length, delivers excellent rate capability and good cyclic stability over the Li‐ion batteries of conventional configurations.     

A Novel Surface Treatment Method and New Insight into Discharge Voltage Deterioration for High‐Performance 0.4Li2MnO3–0.6LiNi1/3Co1/3Mn1/3O2 Cathode Materials

The Li‐rich cathode materials have been considered as one of the most promising cathodes for high energy Li‐ion batteries. However, realization of these materials for use in Li‐ion batteries is currently limited by their intrinsic problems. To overcome this barrier, a new surface treatment concept is proposed in which a hybrid surface layer composed of a reduced graphene oxide (rGO) coating and a chemically activated layer is created. A few layers of GO are first coated on the surface of the Li‐rich cathode material, followed by a hydrazine treatment to produce the reducing agent of GO and the chemical activator of the Li₂MnO₃ phase. Compared to previous studies, this surface treatment provides substantially improved electrochemical performance in terms of initial Coulombic effiency and retention of discharge voltage. As a result, the surface‐treated 0.4Li­₂MnO_3–0.6LiNi_1/3Co_1/3Mn_1/3O₂ exhibits a high capacity efficiency of 99.5% during the first cycle a the discharge capacity of 250 mAh g^?1 (2.0–4.6 V under 0.1C), 94.6% discharge voltage retention during 100 cycles (1C) and the superior capacity retention of 60% at 12C at 24 °C.     

Polymer‐in‐“Quasi‐Ionic Liquid” Electrolytes for High‐Voltage Lithium Metal Batteries

Due to the limited oxidation stability (<4 V) of ether oxygen in its polymer structure, polyethylene oxide (PEO)‐based polymer electrolytes are not compatible with high‐voltage (>4 V) cathodes, thus hinder further increases in the energy density of lithium (Li) metal batteries (LMBs). Here, a new type of polymer‐in‐“quasi‐ionic liquid” electrolyte is designed, which reduces the electron density on ethereal oxygens in PEO and ether solvent molecules, induces the formation of stable interfacial layers on both surfaces of the LiNi_1/3Mn_1/3Co_1/3O₂ (NMC) cathode and the Li metal anode in Li||NMC batteries, and results in a capacity retention of 88.4%, 86.7%, and 79.2% after 300 cycles with a charge cutoff voltage of 4.2, 4.3, and 4.4 V for the LMBs, respectively. Therefore, the use of “quasi‐ionic liquids” is a promising approach to design new polymer electrolytes for high‐voltage and high‐specific‐energy LMBs.     

In Situ TEM Study of Volume Expansion in Porous Carbon Nanofiber/Sulfur Cathodes with Exceptional High‐Rate Performance

Although lithium sulfur batteries (LSBs) have attracted much interest owing to their high energy densities, synthesis of high‐rate cathodes and understanding their volume expansion behavior still remain challenging. Herein, electrospinning is used to prepare porous carbon nanofiber (PCNF) hosts, where both the pore volume and surface area are tailored by optimizing the sacrificial agent content and the activation temperature. Benefiting from the ameliorating functional features of high electrical conductivity, large pore volume, and Li ion permselective micropores, the PCNF/A550/S electrode activated at 550 °C exhibits a high sulfur loading of 71 wt%, a high capacity of 945 mA h g^?1 at 1 C, and excellent high‐rate capability. The in situ transmission electron microscope examination reveals that the lithiation product, Li₂S, is contained within the electrode with only ≈35% volume expansion and the carbon host remains intact without fracture. In contrast, the PCNF/A750/S electrode with damaged carbon spheres exhibits sulfur sublimation, a larger volume expansion of over 61%, and overflowing of Li₂S, a testament to its poor cyclic stability. These findings provide, for the first time, a new insight into the correlation between volume expansion and electrochemical performance of the electrode, offering a potential design strategy to synthesize high‐rate and stable LSB cathodes.     

Ambient‐Pressure Relithiation of Degraded LixNi0.5Co0.2Mn0.3O2 (0 < x < 1) via Eutectic Solutions for Direct Regeneration of Lithium‐Ion Battery Cathodes

With the rapid growth of the lithium‐ion battery (LIBs) market, recycling and re‐use of end‐of‐life LIBs to reclaim lithium (Li) and transition metal (TM) resources (e.g., Co, Ni), as well as eliminating pollution from disposal of waste batteries, has become an urgent task. Here, for the first time the ambient‐pressure relithiation of degraded LiNi_0.5Co_0.2Mn_0.3O₂ (NCM523) cathodes via eutectic Li⁺ molten‐salt solutions is successfully demonstrated. Combining such a low‐temperature relithiation process with a well‐designed thermal annealing step, NCM523 cathode particles with significant Li loss (≈40%) and capacity degradation (≈50%) can be successfully regenerated to achieve their original composition and crystal structures, leading to effective recovery of their capacity, cycling stability, and rate capability to the levels of the pristine materials. Advanced characterization tools including atomic resolution electron microscopy imaging and electron energy loss spectroscopy are combined to demonstrate that NCM523's original layered crystal structure is recovered. For the first time, it is shown that layer‐to‐rock salt phase change on the surfaces and subsurfaces of the cathode materials can be reversed if lithium can be incorporated back to the material. The result suggests the great promise of using eutectic Li⁺ molten–salt solutions for ambient‐pressure relithiation to recycle and remanufacture degraded LIB cathode materials.     

Direct Visualization of the Interfacial Degradation of Cathode Coatings in Solid State Batteries: A Combined Experimental and Computational Study

The interfacial instability between a thiophosphate solid electrolyte and oxide cathodes results in rapid capacity fade and has driven the need for cathode coatings. In this work, the stability, evolution, and performance of uncoated, Li₂ZrO₃‐coated, and Li₃B₁₁O₁₈‐coated LiNi_0.5Co_0.2Mn_0.3O₂ cathodes are compared using first‐principles computations and electron microscopy characterization. Li₃B₁₁O₁₈ is identified as a superior coating that exhibits excellent oxidation/chemical stability, leading to substantially improved performance over cells with Li₂ZrO₃‐coated or uncoated cathodes. The chemical and structural origin of the different performance is interpreted using different microscopy techniques which enable the direct observation of the phase decomposition of the Li₂ZrO₃ coating. It is observed that Li is already extracted from the Li₂ZrO₃ in the first charge, leading to the formation of ZrO₂ nanocrystallites with loss of protection of the cathode. After 50 cycles separated (Co, Ni)‐sulfides and Mn‐sulfides can be observed within the Li₂ZrO₃‐coated material. This work illustrates the severity of the interfacial reactions between a thiophosphate electrolyte and oxide cathode and shows the importance of using coating materials that are absolutely stable at high voltage.     

Effect of ionic liquids activation on laccase from Trametes versicolor: Enzymatic stability and activity

The stability and activity of laccase from Trametes versicolor in two water‐soluble ionic liquids (ILs), namely 1‐butyl‐3‐methylimidazolium methyl sulfate, [bmim][MeSO₄] and 1,3‐dimethylimidazolium methyl sulfate, [mmim][MeSO₄], were investigated in this study. Thermal inactivation of laccase was characterized in the presence of these both ILs and as expected first‐order kinetics was followed. Inactivation rate constant (k), half‐life time (t_1/2), and energy of activation (Ea) were determined. Kinetics of 2,2′‐azino‐bis(3‐ethylbenzthiazoline‐6‐sulfonic acid) oxidation by laccase in the presence of these ILs was studied and Michaelis–Menten parameters were calculated. There is no enzymatic inactivation since the maximum reaction rate remained constant for IL concentrations up to 25%, and surprisingly, it was found that laccase was activated for concentrations of 35% of ILs, since the reaction rate increased 1.7 times.     

High‐Rate Charging Induced Intermediate Phases and Structural Changes of Layer‐Structured Cathode for Lithium‐Ion Batteries

Using fast time‐resolved in situ X‐ray diffraction, charge‐rate dependent phase transition processes of layer structured cathode material LiNi_1/3Mn_1/3Co_1/3O₂ for lithium‐ion batteries are studied. During first charge, intermediate phases emerge at high rates of 10C, 30C, and 60C, but not at low rates of 0.1C and 1C. These intermediate phases can be continuously observed during relaxation after the charging current is switched off. After half‐way charging at high rate, sample studied by scanning transmission electron microscopy shows Li‐rich and Li‐poor phases' coexistence with tetrahedral occupation of Li in Li‐poor phase. The high rate induced overpotential is thought to be the driving force for the formation of this intermediate Li‐poor phase. The in situ quick X‐ray absorption results show that the oxidation of Ni accelerates with increasing charging rate and the Ni⁴⁺ state can be reached at the end of charge with 30C rate. These results give new insights in the understanding of the layered cathodes during high‐rate charging.     

Spectroscopic insight into the interaction of bovine serum albumin with imidazolium‐based ionic liquids in aqueous solution

The study of protein–ionic liquid interactions is very important because of the widespread use of ionic liquids as protein stabilizer in the recent years. In this work, the interaction of bovine serum albumin (BSA) with different imidazolium‐based ionic liquids (ILs) such as [1‐ethyl‐3‐methyl‐imidazolium ethyl sulfate (EmimESO₄), 1‐ethyl‐3‐methyl‐imidazolium chloride (EmimCl) and 1‐butyl‐3‐methyl‐imidazolium chloride (BmimCl)] has been investigated using different spectroscopic techniques. The intrinsic fluorescence of BSA is quenched by ILs by the dynamic mechanism. The thermodynamic analysis demonstrates that very weak interactions exist between BSA and ILs. 8‐Anilino‐1‐naphthalenesulfonic acid (ANS) fluorescence and lifetime measurements reveal the formation of the compact structure of BSA in IL medium. The conformational changes of BSA were monitored by CD analysis. Temperature‐dependent ultraviolet (UV) measurements were done to study the thermal stability of BSA. The thermal stability of BSA in the presence of ILs follows the trend EmimESO₄ > EmimCl > BmimCl and in the presence of more hydrophobic IL, destabilization increases rapidly as a function of concentration.     

In Situ Probing and Synthetic Control of Cationic Ordering in Ni‐Rich Layered Oxide Cathodes

Ni‐rich layered oxides (LiNi_1–x M_x O₂; M = Co, Mn, …) are appealing alternatives to conventional LiCoO₂ as cathodes in Li‐ion batteries for automobile and other large‐scale applications due to their high theoretical capacity and low cost. However, preparing stoichiometric LiNi_1–x M_x O₂ with ordered layer structure and high reversible capacity, has proven difficult due to cation mixing in octahedral sites. Herein, in situ studies of synthesis reactions and the associated structural ordering in preparing LiNiO₂ and the Co‐substituted variant, LiNi_0.8Co_0.2O₂, are made, to gain insights into synthetic control of the structure and electrochemical properties of Ni‐rich layered oxides. Results from this study indicate a direct transformation of the intermediate from the rock salt structure into hexagonal phase, and during the process, Co substitution facilities the nucleation of a Co‐rich layered phase at low temperatures and subsequent growth and stabilization of solid solution Li(Ni, Co)O₂ upon further heat treatment. Optimal conditions are identified from the in situ studies and utilized to obtain stoichiometric LiNi_0.8Co_0.2O₂ that exhibits high capacity (up to 200 mA h g^?1 ) with excellent retention. The findings shed light on designing high performance Ni‐rich layered oxide cathodes through synthetic control of the structural ordering in the materials.