Effects of initial population density (IPD) on growth and lipid composition of Nannochloropsis sp.

The microalga Nannochloropsis sp. was cultured under different initial population densities (IPDs) ranging from 0.11 to 9.09 g L^?1. The IPD affected the biomass and lipid accumulation significantly. The algal cultured with higher IPD resulted higher biomass concentration (up to 13.07 g L^?1) in 10 days growth. The biomass productivity with 0.98 g L^?1 IPD was 0.75 g L^?1 d^?1 which was higher than that of other IPDs. For IPDs ranging from 0.11 to 0.98 g L^?1, with the increase of IPD, the biomass productivity increased, while for IPD over 0.98 g L^?1, the biomass productivity decreased. Lipid content of the algal culture started with 0.11 g L^?1 IPD reached to 42 % of dry weight. But with the increase of IPD, the lipid content decreased. Lipid composition was analyzed using thin layer chromatography coupled with flame ionization detection (TLC/FID). Seven lipid classes were identified and quantified. The main reserve lipid, triacylglyceride (TAG), accumulated under all different IPD conditions. However, with the increasing IPD values, TAG content decreased from 59.1 to 23.5 % of the total lipids. Based on these results, to obtain the maximal biomass productivity and lipid productivity of Nannochloropsis sp. in mass cultivation systems, it is necessary to select an appropriate IPD.     

The potential of microalgal biomass production for biotechnological purposes using wastewater resources

The utilization of microalgae for wastewater treatment represents an attractive opportunity for wastewater valorization through the use of the produced biomass. Five strains of microalgae were isolated from municipal wastewater and grown in autoclaved and non-autoclaved effluent at 30 °C and 150 μmol photons m^?2 s^?1 to study biomass production, nutrient removal, and the biochemical composition of the biomass. All strains reached high biomass productivity (35.6 to 54.2 mg dry weight L^?1 day^?1) within 4 days of batch culturing. In this period, ammonium-N and phosphate were reduced by more than 60 and 90 %, respectively. The high growth rate (0.57 to 1.06 day^?1) ensured a rapid removal of nutrients and thereby a short retention time. By the fourth day of cultivation, the algal biomass contained 32 % protein, but only 11 % lipids and 18 % carbohydrates. It was found that the biomass was a suitable raw material for biogas production by anaerobic digestion. Biodigestion of obtained biomass was simulated by employing the Aspen HYSYS modeling software, resulting in methane yields comparable to those found in the literature. The elemental analysis of the algal biomass showed very low concentrations of pollutants, demonstrating the potential of use of the digestate from biodigestion as a bio-fertilizer.     

At high temperature lipid production in Ettlia oleoabundans occurs before nitrate depletion

Temperature and light intensity effects on biomass and lipid production were investigated in Ettlia oleoabundans to better understand some fundamental properties of this potentially useful but poorly studied microalgal species. E. oleoabundans entered dormant state at 5 °C, showed growth at 10 °C, and when exposed to light at 70 μmol photons per square meter per second at 10 °C, cells reached a biomass concentration of >2.0 g?L^?1 with fatty acid methyl esters of 11.5 mg?L^?1. Highest biomass productivity was at 15 °C and 25 °C regardless of light intensity, and accumulation of intracellular lipids was stimulated by nitrate depletion under these conditions. Although growth was inhibited at 35 °C, at 130 μmol photons per square meter per second lipid content reached 10.37 mg?L^?1 with fatty acid content more favorable to biodiesel dominating; this occurred without nitrate depletion. In a two-phase temperature shift experiment at two nitrate levels, cells were shifted after 21 days at 15 °C to 35 °C for 8 days. Although after the shift growth continued, lipid productivity per cell was less than that in the 35 °C cultures, again without nitrate depletion. This study showed that E. oleoabundans grows well at low temperature and light intensity, and high temperature can be a useful trigger for lipid accumulation independent of nitrate depletion. This will prove useful for improving our knowledge about lipid production in this and other oleaginous algae for modifying yield and quality of algal lipids being considered for biodiesel production.     

Effects of stationary phase elongation and initial nitrogen and phosphorus concentrations on the growth and lipid-producing potential of Chlorella sp. HQ

Higher lipid production and nutrient removal rates are the pursuing goals for synchronous biodiesel production and wastewater treatment technology. An oleaginous alga Chlorella sp. HQ was tested in five different synthetic water, and it was found to achieve the maximum biomass (0.27 g L^?1) and lipid yield (41.3 mg L^?1) in the synthetic secondary effluent. Next, the effects of the stationary phase elongation and initial nitrogen (N) and phosphorus (P) concentrations were investigated. The results show that the algal characteristics were affected apparently under different N concentrations but not P, which were verified by Logistic and Monod models. At the early stationary phase, the algal biomass, lipid and triacylglycerols (TAGs) yields, and P removal efficiency increased and reached up to 0.19 g L^?1, 46.7 mg L^?1, 14.3 mg L^?1, and 94.3 %, respectively, but N removal efficiency decreased from 86.2 to 26.8 % under different N concentrations. And the largest TAGs yield was only 6.4 mg L^?1 and N removal efficiency was above 71.1 % under different P concentrations. At the late stationary phase, the maximal biomass, lipid and TAGs yields, and P removal efficiencies primarily increased as the initial N and P concentrations increase and climbed up to 0.49 g L^?1, 99.2 mg L^?1, 54.0 mg L^?1, and 100.0 %, respectively. It is concluded that stationary phase elongation is of great importance and the optimal initial N/P ratio should be controlled between 8/1 and 20/1 to serve Chlorella sp. HQ for better biodiesel production and secondary effluent purification.     

Interspecific biodiversity enhances biomass and lipid productivity of microalgae as biofuel feedstock

Large improvements in biomass and lipid production are required to make massive scale algal biodiesel production an economic reality. The application of the biodiversity strategy to enhance algal biomass as biofuel feedstock is little. The algal diversity was manipulated in this study to investigate the effects of a combination of biodiversity complementarity and a new medium consisting of seawater and agricultural fertilizer on lipid productivity. The algae diverse community includes two strains of Dunaliella salina (Dunaliella salina 19/30 and 19/18) and three species of Nannochloropsis (Nannochloropsis oculata, Nannochloropsis salina, and Nannochloropsis gaditana). The results showed that the most diverse community (5 species) produced an average of sixfold more biomass in the new medium than did the standard f/2 culture medium. The most diverse polyculture had the highest growth rate (1.01 day^?1), biomass (1.2 g L^?1), and lipid productivity (0.31 g L^?1 day^?1). The assessment of algal polycultures relative to monocultures is particularly interesting and novel for this biofuel field, and the observations that these polycultures resulted in significant lipid productivity improvements are very useful addition to the biofuel research. The possible mechanism (resource diversity) to explain the synergy in mixed cultures warrants further investigation.     

Triacylglycerol content,productivity and fatty acid profile in Scenedesmus acutus PVUW12

A detailed lipid characterization of Scenedesmus acutus PVUW12, with emphasis on the evaluation of triacylglycerols (TAGs) as a biodiesel feedstock, is presented. When algal cells were grown in nitrogen-free medium (N stress), a lipid increase was detected that was mainly due to TAG accumulation. In situ fluorescence measurements allowed the kinetics and extent of neutral lipid accumulation to be followed. Under N stress, the productivity of total lipids and TAGs increased significantly (80.99 and 63.74 mg L^?1 day^?1, respectively) compared with controls (29.51 and 16.23 mg L^?1 day^?1, respectively). Monounsaturated fatty acids were the major fraction and increased further (49.74 %) in stressed cells, with oleic acid as the most abundant compound (46.97 %). The polyunsaturated fatty acid composition of this algal oil appears to meet the European Standard EN 14214. These results indicate that S. acutus oil meets the requirements for its use as a biodiesel feedstock. Since this strain was also proposed for wastewater bioremediation, this opens up the possibility of its use in an integrated system combined with biofuel production.     

High-productivity lipid production using mixed trophic state cultivation of <Emphasis Type="Italic">Auxenochlorella</Emphasis> (<Emphasis Type="Italic">Chlorella</Emphasis>) <Emphasis Type="Italic">protothecoides</Emphasis>

A mixed trophic state production process for algal lipids for use as feedstock for renewable biofuel production was developed and deployed at subpilot scale using a green microalga, Auxenochlorella (Chlorella) protothecoides. The process is composed of two separate stages: (1) the photoautotrophic stage, focused on biomass production in open ponds, and (2) the heterotrophic stage focused on lipid production and accumulation in aerobic bioreactors using fixed carbon substrates (e.g., sugar). The process achieved biomass and lipid productivities of 0.5 and 0.27 g/L/h that were, respectively, over 250 and 670 times higher than those obtained from the photoautotrophic cultivation stage. The biomass oil content (over 60 % w/DCW) following the two-stage process was predominantly monounsaturated fatty acids (~82 %) and largely free of contaminating pigments that is more suitable for biodiesel production than photosynthetically generated lipid. Similar process performances were obtained using cassava hydrolysate as an alternative feedstock to glucose.     

Growth and lipid synthesis promotion in mixotrophic Neochloris oleoabundans (Chlorophyta) cultivated with glucose

In the recent years, the studies concerning the cultivation of Neochloris oleoabundans for biofuel purposes have increased, in relation to its capability to accumulate lipids when grown under nutrient starvation. Unfortunately, this cultivation mode does not allow to reach high biomass densities, which are required to improve the feasibility of the process. Increasing knowledge of the microalgal physiology is necessary to obtain new useful information for the improvement of culture performance in the perspective of large-scale cultivation. In this work, the mixotrophic cultivation of N. oleoabundans in a brackish medium added with different glucose concentrations has been tested under shaking, with the aim of stimulating growth alongside lipid accumulation inside cells. Cell morphology, glucose consumption, photosynthetic pigment content and photosynthetic efficiency were also investigated. Among all tested glucose concentrations (0–30 g L^?1), it was observed that 2.5 g L^?1 was the optimal concentration, allowing to obtain the best compromise between glucose supplement, biomass production and lipid accumulation. Growth was highly enhanced in mixotrophic cultures, linked to the release of cells from sporocysts. A unique feature characterising mixotrophy in N. oleoabundans was the promotion of the maximum quantum yield of Photosystem II. Moreover, when mixotrophic cells entered the stationary phase, high lipid accumulation was induced. This study shows that the addition of glucose to N. oleoabundans remarkably increases the production of biomass enriched in lipids and represents an advancement for the cultivation of this microalga for applied purposes.     

Coupling microbial fuel cells with a membrane photobioreactor for wastewater treatment and bioenergy production

Microbial fuel cells (MFCs) and membrane photobioreactors are two emerging technologies for simultaneous wastewater treatment and bioenergy production. In this study, those two technologies were coupled to form an integrated treatment system, whose performance was examined under different operating conditions. The coupled system could achieve 92–97 % removal of soluble chemical oxygen demand (SCOD) and nearly 100 % removal of ammonia. Extending the hydraulic retention time (HRT) of the membrane photobioreactor to 3.0 days improved the production of algal biomass from 44.4 ± 23.8 to 133.7 ± 12.9 mg L^?1 (based on the volume of the treated water). When the MFCs were operated in a loop mode, their effluent (which was the influent to the algal reactor) contained nitrate and had a high pH, leading to the decreased algal production in the membrane photobioreactor. Energy analysis showed that the energy consumption was mainly due to the recirculation of the anolyte and the catholyte in the MFCs and that decreasing the recirculation rates could significantly reduce energy consumption. The energy production was dominated by indirect electricity generation from algal biomass. The highest energy production of 0.205 kWh m^?3 was obtained with the highest algal biomass production, resulting in a theoretically positive energy balance of 0.033 kWh m^?3. Those results have demonstrated that the coupled system could be an alternative approach for energy-efficient wastewater treatment and using wastewater effluent for algal production.     

The effect of nitrogen limitation on lipid productivity and cell composition in Chlorella vulgaris

Chlorella vulgaris accumulates lipid under nitrogen limitation, but at the expense of biomass productivity. Due to this tradeoff, improved lipid productivity may be compromised, despite higher lipid content. To determine the optimal degree of nitrogen limitation for lipid productivity, batch cultures of C. vulgaris were grown at different nitrate concentrations. The growth rate, lipid content, lipid productivity and biochemical and elemental composition of the cultures were monitored for 20 days. A starting nitrate concentration of 170 mg L^?1 provided the optimal tradeoff between biomass and lipid production under the experimental conditions. Volumetric lipid yield (in milligram lipid per liter algal culture) was more than double that under nitrogen-replete conditions. Interpolation of the data indicated that the highest volumetric lipid concentration and lipid productivity would occur at nitrate concentrations of 305 and 241 mg L^?1, respectively. There was a strong correlation between the nitrogen content of the cells and the pigment, protein and lipid content, as well as biomass and lipid productivity. Knowledge of the relationships between cell nitrogen content, growth, and cell composition assists in the prediction of the nitrogen regime required for optimal productivity in batch or continuous culture. In addition to enhancing lipid productivity, nitrogen limitation improves the lipid profile for biodiesel production and reduces the requirement for nitrogen fertilizers, resulting in cost and energy savings and a reduction in the environmental burden of the process.     

Utilization of cane molasses towards cost-saving astaxanthin production by a Chlorella zofingiensis mutant

The aim of the present study was to survey the growth and astaxanthin production of E17, an astaxanthin-rich mutant of Chlorella zofingiensis, through feeding the low-cost carbon source cane molasses. In heterotrophic batch cultivation, E17 fed with pretreated molasses achieved biomass (1.79 g L^?1 day^?1) and astaxanthin (1.99 mg L^?1 day^?1) productivities comparable to those with glucose, which were about 2- and 2.8-fold of those fed with untreated molasses, respectively. Molasses-induced astaxanthin accumulation may be attributed to the elicited expression of carotenogenic genes, in particular the genes specifically responsible for the ketolation and hydroxylation of β-carotene to form astaxanthin. A two-stage fed-batch strategy was employed to grow E17 and induce astaxathin accumulation, resulting in 45.6 g L^?1 biomass and 56.1 mg L^?1 astaxanthin, the highest volumetric astaxanthin yield ever reported for this alga. In addition, the astaxanthin production by E17 was tested with a semi-continuous culture method, where the directly diluted raw molasses (giving 5 g L^?1 sugar) was used as the carbon source. Little growth inhibition of E17 was observed in the semi-continuous culture with a biomass productivity of 1.33 g L^?1 day^?1 and an astaxanthin productivity of 0.83 mg L^?1 day^?1. The mixotrophic semi-continuous cultures enhanced the biomass and astaxanthin productivities by 29.3 % and 42.2 %, respectively. This study highlights the potential of using the industrially cheap cane molasses towards large-scale cost-saving production of the high-value ketocarotenoid astaxanthin.     

Effects of different nitrogen, phosphorus, and iron concentrations and salinity on lipid production in newly isolated strain of the tropical green microalga, Scenedesmus dimorphus KMITL

The fatty acid composition, the effect of different concentrations of nitrogen (16.5-344 mg ?L^?1), phosphorus (9–45 mg? L^?1), iron (9–45 mg? L^?1) and salinity levels (0–20 psu) on lipid production in the green microalga Scenedesmus dimorphus KMITL, a new strain isolated from a tropical country, Thailand, were studied. The alga was isolated from a freshwater fish pond, and cultured in Chlorella medium by varying one parameter at a time. The main fatty acid composition of this strain was C16–C18 (97.52 %) fatty acids. A high lipid content was observed in conditions of 16.5 mg? L^?1-N, or 22 mg ?L^?1-P, or 45 mg ?L^?1-Fe, or 5 psu salinity, which accumulated lipids to 20.3?±?0.4, 19.4?±?0.2, 24.7?±?0.5, and 14.3?±?0.2 % of algal biomass, respectively. Increasing lipid content and lipid productivity was noted when the alga was cultured under high iron concentration and high salinity, as well as under reduced phosphorus conditions, whereas nitrogen limitation only resulted in an increased lipid content.     

Phenol degradation and colour removal in submerged culture of Pleurotus sajor-caju with paper mill effluents

The fungus Pleurotus sajor-caju secretes phenol-oxidases that enable the use of recalcitrant compounds as substrates. The residues of paper manufacture contain high lignin levels, which gives the effluents a characteristic brownish colour. To test the potential of P. sajor-caju cultures on reducing these parameters, we used 90% of raw effluents from medium consistency oxygen delignification and bleaching stages plus 10% of mineral solution and different levels of glucose (5–15 g L^?1) as substrate. We observed a greater fungal biomass in cultures using effluent than in controls. Cultures containing 10 to 15 g L^?1 of glucose resulted in about 42% colour reduction. The polyphenol content was also reduced by 58.9% by the 13th day of culture. In addition, we observed the secretion of laccases (211.44 U mL^?1 and 45.98 U mL^?1 using ABTS and syringaldazine, respectively) and peroxidases (6.11 U mL^?1-ABTS) both peaking at the 7th day of culture and with similar kinetics of production in different glucose concentrations.     

Biomass,Lipid and Fatty Acid Production in Large-Scale Cultures of the Marine Macroalga Derbesia tenuissima (Chlorophyta)

Biomass productivity was quantified for the marine macroalga Derbesia tenuissima cultivated outdoors at seven stocking densities from 0.25 to 8 g L^?1 for 5 weeks. Total lipids and fatty acid quantity and quality was measured from samples that were freeze-dried, dried by oven (75 °C), food dehydrator (60 °C), or outdoor in the sun (40 °C) or shade (38 °C). Stocking densities of 0.25 to 2 g L^?1 yielded the highest biomass productivities (>20 g dry weight m^?2 day^?1) with no effect on total lipid quantity (11 %), or fatty acid quantity (5.3 %) or quality at any density tested. However, there was an interactive effect of stocking density and drying technique, with a decrease of up to 40 % in polyunsaturated fatty acids in sun-dried compared to freeze-dried biomass. Notably, while fatty acid and biomass productivity may be inseparable in macroalgae, cultivation conditions have a significant carryover effect in the post-harvest delivery of high-quality bio-oils.     

Monitoring oil production for biobased feedstock in the microalga <Emphasis Type="Italic">Nannochloropsis</Emphasis> sp.: a novel method combining the BODIPY BD-C12 fluorescent probe and simple image processing

A simple reliable method with fast response for lipid detection and quantification is proposed, combining a new highly lipophilic fluorescent probe BODIPY BD-C12 and image analysis to determine the algal lipid content and the lipid production in the microalgae Nannochloropsis sp. Lipid bodies stained with BODIPY BD-C12 have a characteristic multicolor fluorescence, and their volumes were determined using a sphere volume approach. The method developed was applied in the evaluation of lipid accumulation by Nannochloropsis sp. under different cultivation conditions (varying nitrate and salinity concentrations and combined effect of these two variables). The results show an increase of lipid content in Nannochloropsis sp. cultivated in nitrogen replete and depleted conditions, from 9.4 to 40.8 μm³ cell^?1 and 35.5 to 73.5%, respectively. The findings are also compared with conventional methods for determination of neutral lipids and with results obtained from the dyes Nile Red and BODIPY 505/515. A reasonable agreement between neutral lipid production measured by BODIPY BD-C12 and gravimetric methods (correlation coefficient of 0.98) was obtained. The neutral lipids production decreased from 964.6 to 244.8 mg L^?1 and from 809.1 to 396.7 mg L^?1, as the nitrate concentration increased from 0 to 0.3 g L^?1. It is observed that, with the two commercially available dyes, lipid quantification using Nile Red leads to an overestimation of lipids, while the use of BODIPY 505/515 promoted unreliable measures due to rapid bleaching of the chromophore. The method proposed shows excellent potential to become a standard, yet advanced, strategy for rapid evaluation and quantification of intracellular lipids in microalgae, a crucial step of the scaling-up process involved in the production of biobased products.     

Inorganic carbon and pH effect on growth and lipid productivity of Tetraselmis suecica and Chlorella sp (Chlorophyta) grown outdoors in bag photobioreactors

There has been considerable interest in cultivation of green microalgae (Chlorophyta) as a source of lipid that can alternatively be converted to biodiesel. However, almost all mass cultures of algae are carbon-limited. Therefore, to reach a high biomass and oil productivities, the ideal selected microalgae will most likely need a source of inorganic carbon. Here, growth and lipid productivities of Tetraselmis suecica CS-187 and Chlorella sp were tested under various ranges of pH and different sources of inorganic carbon (untreated flue gas from coal-fired power plant, pure industrial CO₂, pH-adjusted using HCl and sodium bicarbonate). Biomass and lipid productivities were highest at pH 7.5 (320?±?29.9 mg biomass L^?1 day^?1and 92?±?13.1 mg lipid L^?1 day^?1) and pH 7 (407?±?5.5 mg biomass L^?1 day^?1 and 99?±?17.2 mg lipid L^?1 day^?1) for T. suecica CS-187 and Chlorella sp, respectively. In general, biomass and lipid productivities were pH 7.5?>?pH 7?>?pH 8?>?pH 6.5 and pH 7?>?pH 7.5?=?pH 8?>?pH 6.5?>?pH 6?>?pH 5.5 for T. suecica CS-187 and Chlorella sp, respectively. The effect of various inorganic carbon on growth and productivities of T. suecica (regulated at pH?=?7.5) and Chlorella sp (regulated at pH?=?7) grown in bag photobioreactors was also examined outdoor at the International Power Hazelwood, Gippsland, Victoria, Australia. The highest biomass and lipid productivities of T. suecica (51.45?±?2.67 mg biomass L^?1 day^?1 and 14.8?±?2.46 mg lipid L^?1 day^?1) and Chlorella sp (60.00?±?2.4 mg biomass L^?1 day^?1 and 13.70?±?1.35 mg lipid L^?1 day^?1) were achieved when grown using CO₂ as inorganic carbon source. No significant differences were found between CO₂ and flue gas biomass and lipid productivities. While grown using CO₂ and flue gas, biomass productivities were 10, 13 and 18 %, and 7, 14 and 19 % higher than NaHCO₃, HCl and unregulated pH for T. suecica and Chlorella sp, respectively. Addition of inorganic carbon increased specific growth rate and lipid content but reduced biomass yield and cell weight of T. suecica. Addition of inorganic carbon increased yield but did not change specific growth rate, cell weight or content of the cell weight of Chlorella sp. Both strains showed significantly higher maximum quantum yield (F_v/F_m) when grown under optimum pH.     

Biomass and lipid enhancement in Ankistrodesmus sp. cultured with reused and minimal nutrients media

Microalgae are a promising feedstock for biofuel production. Lipid content in microalgae could be enhanced under nutrient depletion. This work investigated the effect of the nutrient on lipid accumulation in Ankistrodesmus sp. culture. Batch cultures were carried out using fresh BG11 medium, and after the harvest, the medium was reused for the next culture; this method was repeated two times. The maximum lipid productivity of 29.75 mg L^?1 day^?1 was obtained from the culture with the second reuse medium. In continuous cultures, Ankistrodesmus sp. was cultured in both fresh and modified BG11 mediums. The modified BG11 medium was adjusted to resemble the content of the first reuse medium. As a comparison between batch and continuous cultures, it was proven that the productivity in the continuous culture was better than in the batch, where the achievable maximum biomass and lipid were 188.30 and 38.32 mg L^?1 day^?1. The maximum lipid content of 34.22% was obtained from the continuous culture at a dilution rate of 0.08 day^?1, whereas the maximum saturated and unsaturated fatty acid productivities of 79.96 and 104.54 mg L^?1 day^?1 were obtained at a dilution rate of 0.16 day^?1.     

Effect of nitrate on lipid production by T. suecica, M. contortum, and C. minutissima

Microalgae are an alternative and sustainable source of lipids that can be used as a feedstock for biodiesel production. Nitrate is a good nitrogen source for many microalgae and affects biomass and lipid yields of microalgae. In this study, the effect of nitrate on cell growth and lipid production and composition in Monoraphidium contortum, Tetraselmis suecica, and Chlorella minutissima was investigated. Nitrate affected the production of biomass and the production and composition of lipids of the three microalgae tested. Increasing the nitrate concentration in the culture medium resulted in increased biomass production and higher biomass productivity. Furthermore, increasing the nitrate concentration resulted in a reduction in lipid content and productivity in M. contortum; however, the opposite effect was observed in T. suecica and C. minutissima cultures. C. minutissima and M. contortum lipids contain high levels of oleic acid, with values ranging from 26 to 45.7% and 36.4 to 40.1%, respectively. The data suggest that because of its high lipid productivity (13.79 mg L^?1 d^?1) and high oleic acid productivity (3.78 mg L^?1 d^?1), Chlorella minutissima is a potential candidate for the production of high quality biodiesel.     

The effect of sodium bicarbonate supplementation on growth and biochemical composition of marine microalgae cultures

The addition of bicarbonate (NaHCO₃; 0, 1, or 2 g L^?1) to microalgal cultures has been evaluated for two species (Tetraselmis suecica and Nannochloropsis salina) in respect of growth and biochemical composition. In batch cultures, addition of bicarbonate (1 g L^?1) resulted in significantly (P?<?0.05) higher final mean cell abundances for both species. No differences in specific growth rates (SGRs) were recorded for T. suecica between treatments; however, increasing bicarbonate addition decreased SGR values in N. salina cultures. Bicarbonate addition (1 g L^?1) significantly improved nitrate utilisation from the external media and photosynthetic efficiency (F _v /F _m ) in both species. For both T. suecica and N. salina, bicarbonate addition significantly increased the cellular concentrations of total pigments (3,432–3,587 and 19–37 fg cell^?1, respectively) compared to cultures with no additional bicarbonate (1,727 and 11 fg cell^?1, respectively). Moreover, final concentrations of total cellular fatty acids in T. suecica and N. salina cultures supplemented with 2 g L^?1 bicarbonate (7.6?±?1.2 and 1.8?±?0.1 pg cell^?1, respectively) were significantly higher than those cells supplemented with 0 or 1 g L^?1 bicarbonate (3.2–3.5 and 0.9–1.0 pg cell^?1, respectively). In nitrate-deplete cultures, bicarbonate addition caused species-specific differences in the rate of cellular lipid production, rates of change in fatty acid composition and final lipid levels. In summary, the addition of sodium bicarbonate is a viable strategy to increase cellular abundance and concentrations of pigments and lipids in some microalgae as well as the rate of lipid accumulation in nitrate-deplete cultures.     

Effects of Initial Phosphorus Concentration and Light Intensity on Biomass Yield per Phosphorus and Lipid Accumulation of Scenedesmus sp. LX1

Phosphorus has been considered as one of the most important limiting resources of large-scale production of microalgal biofuel. The approaches to increase biomass yield per phosphorus, along with the lipid accumulation properties of Scenedesmus sp. LX1, were investigated in this study. It was found that practical biomass yield per phosphorous was reduced with the increase of initial phosphorus (P) concentration, but increased with light intensity. The highest biomass yield per P of 4,500 kg-biomass/kg-P was achieved at initial phosphorus concentration of 0.05 mg?·?L^?1 under the light intensity of 320 μmol photon?·?m^?2?·?s^?1. Furthermore, the lipid content per biomass and triacylglycerols (TAGs) content per lipid were found to be positively correlated to biomass yield per P. With the biomass yield increased from 2,800 kg-biomass/kg-P to 4,500 kg-biomass/kg-P, the lipid content per microalgal biomass and TAG content per lipid increased from 18.7 % to 35.0 % and from 69.5 % to 83.0 %. These results suggested a possible approach to achieve high biomass production and high lipid content simultaneously.