Manipulation of remodeling pathways to enhance the mechanical properties of a tissue engineered blood vessel

There is a current need for a small diameter vascular graft due to the limited supply of autogenous grafts and the failure of synthetic grafts due to thrombosis and/or intimal hyperplasia. The use of living cells and tissues to fabricate a small diameter graft (i.e., tissue engineered blood vessel, TEBV) could be useful given the endothelialization potential and biocompatibility benefits of such a graft. However, while sufficient strength has been attained in a TEBV, coordinate compliance has yet to be fine-tuned. In this study we investigate the effects of biological response modifiers, retinoic acid (RA) and ascorbic acid (AA) on TEBV biomechanics as a function of time and subsequently correlate observed RA/AA induced changes in TEBV mechanics with alterations in smooth muscle cell (SMC) biochemistry. TEBVs were constructed using a fibrillar type I collagen network populated by human aortic smooth muscle cells (AoSMC). Following construction this TEBV was treated with 0.3 mM AA and 0.1 mM RA (concentrations found to induce changes in VSMC phenotype). Ultimate tensile stress (UTS), rate of relaxation (RR) and elastic efficiency (EE) of RA/AA treated and untreated TEBVs were measured following 1, 7, 15, 30, 45, and 60 days of treatment. At corresponding time points, the effect of these treatments on collagen and elastin protein synthesis and mRNA expression was examined. RA/AA treated TEBV strength increased and stiffness decreased compared to controls as a function of time. Relative collagen synthesis in treated TEBVs exceeded control levels by nearly two-fold at 15 and 30 days of incubation. RA/AA treated collagen gene expression followed a similar trend. Relative elastin synthesis was also greater in treated TEBVs as compared to untreated TEBVs at 15 and 30 days of incubation and correspondingly elastin mRNA expression was significantly elevated at 15 days of incubation. These data provide evidence that RA/AA treated TEBVs exhibit mechanical properties which more closely mimic those of a native vessel than their untreated counterparts and that changes in extracellular matrix composition and matrix gene expression in the presence of RA/AA treatment may play an important role in the development of said mechanical properties.     

Mechanical remodeling of small-intestine submucosa small-diameter vascular grafts--a preliminary report

Small-intestine submucosa (SIS) is cell-free, 100-mu-thick collagen derived from the small intestine. It has been used as a vascular graft and has the highly desirable ability to be remodeled to become histologically indistinguishable from native adjacent artery. To date there has been limited reporting of its preimplantation and explant mechanical properties as a vascular graft. In this study, compliance, elastic modulus, and burst pressure were measured on preimplant-tested 5- and 8-mm SIS grafts and two 60-day remodeled grafts. Seven prefabricated grafts were implanted in the carotid (n = 7) in dogs, which were sacrificed after 55-63 days. The animals (n = 4) weighed from 22 to 27 kg. One dog received a unilateral carotid graft, and 3 dogs received bilateral carotid grafts. The fabrication technique employed hand-suturing with either nonresorbable or resorbable sutures. None of the grafts had a patency failure. Angiograms taken at 1 month and just before explantation showed uniform flow and no dilation. At the time of explantation, all carotid grafts were found to be encased in fibrous tissue. The grafts made with nonresorbable sutures showed thicker tissue growth at the suture line compared with those made with the resorbable sutures. Along the suture line, the grafts made with resorbable sutures exhibited a more natural color than those sutured with nonresorbable sutures. When the explanted carotid grafts were slit open, the lumen was white, shiny, and glistening. The grafts sutured with nonresorbable sutures exhibited small areas of fibrin and red blood cells when the suture was within the lumen. The resorbable-sutured grafts did not exhibit this response. The mean compliance (percent diameter increase for a pressure rise from 80 to 120 mm Hg) was on average 4.6% (range, 2.9%-8.6%) for the 5-mm preimplant-tested grafts. For the 8-mm preimplant-tested grafts, the increase in diameter for the same pressure rise was 8.7%, on average (range, 7.2% to 9.5%). For comparison, the small-diameter SIS graft at the time of implantation was about one half as compliant as the adjacent dog carotid artery, about 4 times more compliant than a typical vein graft, and more than 10 times more compliant than synthetic vascular grafts. The compliance measured on two 60-day carotid grafts was 10.5% and 7.2%, respectively. This is midway between the original compliance value and the compliance of a typical canine carotid artery (14%), indicating that mechanical remodeling occurred. The modulus of elasticity (E) increased exponentially with increasing pressure according to E = E0e alpha P, where E0 is the zero-pressure modulus and alpha is the exponent that describes the rate of increase in E with pressure; the unit of measure for variables E, E0, and P is g/cm2. The mean value for E0 was 4106 gm/cm2 (range, 1348-5601). The mean value for alpha was 0.0059 (range, 0.0028-0.0125). At 100 mm Hg, the mean value for E was 8.03 x 10(6) dynes/cm2 (range, 4.95-15.7 x 10(6)). For a 60-day SIS graft implant, the elastic modulus at 100 mm Hg decreased from a high value at implant time to twice that of a typical native canine carotid artery. The mean burst pressure for 5.5-mm grafts was 3517 mm Hg (range, 2069-4654). The burst pressure of the remodeled carotid grafts averaged 5660 mm Hg. The burst pressure for a typical carotid artery is about 5000 mm Hg. The results of this preliminary study complement those of previous SIS-vascular-graft studies and add a new factor, namely that the mechanical properties of the remodeled graft approach those of the vessel it replaces.     

Effect of temperature on the biaxial mechanics of excised lung parenchyma of the dog.

The influence of temperature on the mechanical properties of excised saline-filled lung parenchyma of the dog was studied at low lung volume. The motivation of this study was to determine whether lung tissue material without the influence of surface tension undergoes a phase transition in the 20-40 degrees C range, as does synthetic elastin studied by Urry in 1984-1986. Dynamic biaxial and uniaxial tensile tests were done, and strain vs. Lagrangian stress curves were recorded during slow cooling and heating between 40 and 10 degrees C. To emphasize the effects of elastin, strains (defined as stretch ratio minus one) were kept below 30%. A slight decrease in compliance occurred with cooling over the entire temperature range. This effect may be attributed to collagen. It was accompanied by a gradual increase in length as the tissue cooled, an effect that may be attributed to elastin. This process was partially reversible with reheating. However, this effect is in contrast with the sudden drastic change in mechanical properties of synthetic elastin described by Urry. Hysteresis, creep, and stress relaxation were small at these low strains. Possible causes of these effects are discussed.     

Micropatterned cell sheets with defined cell and extracellular matrix orientation exhibit anisotropic mechanical properties

For an arterial replacement graft to be effective, it must possess the appropriate strength in order to withstand long-term hemodynamic stress without failure, yet be compliant enough that the mismatch between the stiffness of the graft and the native vessel wall is minimized. The native vessel wall is a structurally complex tissue characterized by circumferentially oriented collagen fibers/cells and lamellar elastin. Besides the biochemical composition, the functional properties of the wall, including stiffness, depend critically on the structural organization. Therefore, it will be crucial to develop methods of producing tissues with defined structures in order to more closely mimic the properties of a native vessel. To this end, we sought to generate cell sheets that have specific ECM/cell organization using micropatterned polydimethylsiloxane (PDMS) substrates to guide cell organization and tissue growth. The patterns consisted of large arrays of alternating grooves and ridges. Adult bovine aortic smooth muscle cells cultured on these substrates in the presence of ascorbic acid produced ECM-rich sheets several cell layers thick in which both the cells and ECM exhibited strong alignment in the direction of the micropattern. Moreover, mechanical testing revealed that the sheets exhibited mechanical anisotropy similar to that of native vessels with both the stiffness and strength being significantly larger in the direction of alignment, demonstrating that the microscale control of ECM organization results in functional changes in macroscale material behavior.     

The effect of a thermal renal denervation cycle on the mechanical properties of the arterial wall

The aim of this study was to determine the effect that a thermal renal denervation cycle has on the mechanical properties of the arterial wall. Porcine arterial tissue specimens were tested in three groups: native tissue, decellularized tissue, decellularized with collagen digestion (e.g. elastin only). One arterial specimen was used as an unheated control specimen while another paired specimen was subjected to a thermal cycle of 70 °C for 120 s (n=10). The specimens were subjected to tensile loading and a shrinkage analysis. We observed two key results: The mechanical properties associated with the elastin extracellular matrix (ECM) were not affected by the thermal cycle. The effect of the thermal cycle on the collagen (ECM) was significant, in both the native and decellularized groups the thermal cycle caused a statistically significant decrease in stiffness, and failure strength, moreover the native tissue demonstrated a 27% reduction in lumen area post exposure to the thermal cycle. We have demonstrated that a renal denervation thermal cycle can significantly affect the mechanical properties of an arterial wall, and these changes in stiffness and failure strength were associated with alterations to the collagen rather than the elastin extracellular matrix component.     

Development and characterisation of a large diameter decellularised vascular allograft

The aims of this study were to develop a biological large diameter vascular graft by decellularisation of native human aorta to remove the immunogenic cells whilst retaining the essential biomechanical, and biochemical properties for the ultimate benefit of patients with infected synthetic grafts. Donor aortas (n = 6) were subjected to an adaptation of a propriety decellularisation process to remove the cells and acellularity assessed by histological analysis and extraction and quantification of total DNA. The biocompatibility of the acellular aortas was determined using standard contact cytotoxicity tests. Collagen and denatured collagen content of aortas was determined and immunohistochemistry was used to determine the presence of specific extracellular matrix proteins. Donor aortas (n = 6) were divided into two, with one half subject to decellularisation and the other half retained as native tissue. The native and decellularised aorta sections were then subject to uniaxial tensile testing to failure [axial and circumferential directions] and suture retention testing. The data was compared using a paired t-test. Histological evaluation showed an absence of cells in the treated aortas and retention of histoarchitecture including elastin content. The decellularised aortas had less than 15 ng mg^?1 total DNA per dry weight (mean 94% reduction) and were biocompatible as determined by in vitro contact cytotoxicity tests. There were no gross changes in the histoarchitecture [elastin and collagen matrix] of the acellular aortas compared to native controls. The decellularisation process also reduced calcium deposits within the tissue. The uniaxial tensile and suture retention testing revealed no significant differences in the material properties (p > 0.05) of decellularised aorta. The decellularisation procedure resulted in minimal changes to the biological and biomechanical properties of the donor aortas. Acellular donor aorta has excellent potential for use as a large diameter vascular graft.     

Design and production of a chimeric resilin-, elastin-, and collagen-like engineered polypeptide

Protein-inspired biomaterials have gained great interest as an alternative to synthetic polymers, in particular, for their potential use as biomedical devices. The potential inspiring models are mainly proteins able to confer mechanical properties to tissues and organs, such as elasticity (elastin, resilin, spider silk) and strength (collagen, silk). The proper combination of repetitive sequences, each of them derived from different proteins, represents a useful tool for obtaining biomaterials with tailored mechanical properties and biological functions. In this report we describe the design, the production, and the preliminary characterization of a chimeric polypeptide, based on sequences derived from the highly resilient proteins resilin and elastin and from collagen-like sequences. The results show that the obtained chimeric recombinant material exhibits promising self-assembling properties. Young's modulus of the fibers was determined by AFM image analysis and lies in the range of 0.1-3 MPa in agreement with the expectations for elastin-like and resilin-like materials.     

Characterization of evolving biomechanical properties of tissue engineered vascular grafts in the arterial circulation

We used a murine model to assess the evolving biomechanical properties of tissue engineered vascular grafts (TEVGs) implanted in the arterial circulation. The initial polymeric tubular scaffold was fabricated from poly(lactic acid)(PLA) and coated with a 50:50 copolymer of poly(caprolactone) and poly(lactic acid)(P[PC/LA]). Following seeding with syngeneic bone marrow derived mononuclear cells, TEVGs (n=50) were implanted as aortic interposition grafts in wild-type mice and monitored serially using ultrasound. A custom biaxial mechanical testing device was used to quantify the in vitro circumferential and axial mechanical properties of grafts explanted at 3 or 7 months. At both times, TEVGs were much stiffer than native tissue in both directions. Repeated mechanical testing of some TEVGs treated with elastase or collagenase suggested that elastin did not contribute significantly to the overall stiffness whereas collagen did contribute. Traditional histology and immunostaining revealed smooth muscle cell layers, significant collagen deposition, and increasing elastin production in addition to considerable scaffold at both 3 and 7 months, which likely dominated the high stiffness seen in mechanical testing. These results suggest that PLA has inadequate in vivo degradation, which impairs cell-mediated development of vascular neotissue having properties closer to native arteries. Assessing contributions of individual components, such as elastin and collagen, to the developing neovessel is needed to guide computational modeling that may help to optimize the design of the TEVG.     

Effect of elastin degradation on carotid wall mechanics as assessed by a constituent-based biomechanical model

Arteries display a nonlinear anisotropic behavior dictated by the elastic properties and structural arrangement of its main constituents, elastin, collagen, and vascular smooth muscle. Elastin provides for structural integrity and for the compliance of the vessel at low pressure, whereas collagen gives the tensile resistance required at high pressures. Based on the model of Zulliger et al. (Zulliger MA, Rachev A, Stergiopulos N. Am J Physiol Heart Circ Physiol 287: H1335-H1343, 2004), which considers the contributions of elastin, collagen, and vascular smooth muscle cells (VSM) in an explicit form, we assessed the effects of enzymatic degradation of elastin on biomechanical properties of rabbit carotids. Pressure-diameter curves were obtained for controls and after elastin degradation, from which elastic and structural properties were derived. Data were fitted into the model of Zulliger et al. to assess elastic constants of elastin and collagen as well as the characteristics of the collagen engagement profile. The arterial segments were also prepared for histology to visualize and quantify elastin and collagen. Elastase treatment leads to a diameter enlargement, suggesting the existence of significant compressive prestresses within the wall. The elastic modulus was more ductile in treated arteries at low circumferential stretches and significantly greater at elevated circumferential stretches. Abrupt collagen fiber recruitment in elastase-treated arteries leads to a much stiffer vessel at high extensions. This change in collagen engagement properties results from structural alterations provoked by the degradation of elastin, suggesting a clear interaction between elastin and collagen, often neglected in previous constituent-based models of the arterial wall.     

Structure,Mechanical Behavior and Puncture Resistance of Grass Carp Scales

This work is conducted to investigate the hierarchical structure,mechanical behavior and fracture resistance of grass carp scales with different water contents (hydrated and dehydrated) and load conditions (uniaxial,biaxial and punch tests).The whole cross-section of scales is investigated,and it is found that the bony layer displays discontinuity and partly embeds in collagen layer.Four different locations are considered under both tensile and punch tests.The results of the uniaxial tensile test show a correlation between the failure mode and the distribution of surface morphology on scales.The biaxial test results show that there are minor differences in the tensile strength and the Young'modulus compared with those of the uniaxial tests,but the ultimate strain is about 20％-50％.Puncture tests are also conducted with different size of needles and different hardness silicon rubbers as substrate.The results show that the puncture force and deformation are dependent on the size of needle and the hardness of substrate.The failure pattern of scales is related to the water content.Radial cracks occur in the bony layer of hydrated scale,and the collagen fibers twist around the puncture site.However,the shear failure occurs in the bony layer of dehydrated scale.     

A Structurally and Functionally Biomimetic Biphasic Scaffold for Intervertebral Disc Tissue Engineering

Tissue engineering offers high hopes for the treatment of intervertebral disc (IVD) degeneration. Whereas scaffolds of the disc nucleus and annulus have been extensively studied, a truly biomimetic and mechanically functional biphasic scaffold using naturally occurring extracellular matrix is yet to be developed. Here, a biphasic scaffold was fabricated with collagen and glycosaminoglycans (GAGs), two of the most abundant extracellular matrix components in the IVD. Following fabrication, the scaffold was characterized and benchmarked against native disc. The biphasic scaffold was composed of a collagen-GAG co-precipitate making up the nucleus pulposus-like core, and this was encapsulated in multiple lamellae of photochemically crosslinked collagen membranes comprising the annulus fibrosus-like lamellae. On mechanical testing, the height of our engineered disc recovered by ~82-89% in an annulus-independent manner, when compared with the 99% recovery exhibited by native disc. The annulus-independent nature of disc height recovery suggests that the fluid replacement function of the engineered nucleus pulposus core might mimic this hitherto unique feature of native disc. Biphasic scaffolds comprised of 10 annulus fibrosus-like lamellae had the best overall mechanical performance among the various designs owing to their similarity to native disc in most aspects, including elastic compliance during creep and recovery, and viscous compliance during recovery. However, the dynamic mechanical performance (including dynamic stiffness and damping factor) of all the biphasic scaffolds was similar to that of the native discs. This study contributes to the rationalized design and development of a biomimetic and mechanically viable biphasic scaffold for IVD tissue engineering.     

TGF-β1 diminishes collagen production during long-term cyclic stretching of engineered connective tissue: implication of decreased ERK signaling

Cyclic stretching and growth factors like TGF-β have been used to enhance extracellular matrix (ECM) production by cells in engineered tissue to achieve requisite mechanical properties. In this study, the effects of TGF-β1 were evaluated during long-term cyclic stretching of fibrin-based tubular constructs seeded with neonatal human dermal fibroblasts. Samples were evaluated at 2, 5, and 7 weeks for tensile mechanical properties and ECM deposition. At 2 weeks, +TGF-β1 samples had 101% higher collagen concentration but no difference in ultimate tensile strength (UTS) or modulus compared to -TGF-β1 samples. However, at weeks 5 and 7, -TGF-β1 samples had higher UTS/modulus and collagen concentration, but lower elastin concentration compared to +TGF-β1 samples. The collagen was better organized in -TGF-β1 samples based on picrosirius red staining. Western blot analysis at weeks 5 and 7 showed increased phosphorylation of ERK in -TGF-β1 samples, which correlated with higher collagen deposition. The TGF-β1 effects were further evaluated by western blot for αSMA and SMAD2/3 expression, which were 16-fold and 10-fold higher in +TGF-β1 samples, respectively. The role of TGF-β1 activated p38 in inhibiting phosphorylation of ERK was evaluated by treating samples with SB203580, an inhibitor of p38 activation. SB203580-treated cells showed increased phosphorylation of ERK after 1 hour of stretching and increased collagen production after 1 week of stretching, demonstrating an inhibitory role of activated p38 via TGF-β1 signaling during cyclic stretching. One advantage of TGF-β1 treatment was the 4-fold higher elastin deposition in samples at 7 weeks. Further cyclic stretching experiments were thus conducted with constructs cultured for 5 weeks without TGF-β1 to obtain improved tensile properties followed by TGF-β1 supplementation for 2 weeks to obtain increased elastin content, which correlated with a reduction in loss of pre-stress during preconditioning for tensile testing, indicating functional elastin. This study shows that a sequential stimulus approach - cyclic stretching with delayed TGF-β1 supplementation - can be used to engineer tissue with desirable tensile and elastic properties.     

Mechanical properties and composition of mesenteric small arteries of simulated microgravity rats with and without daily -G(x) gravitation

The aim of the present study was to evaluate the active and passive mechanical properties and wall collagen and elastin contents of mesenteric small arteries (MSAs) isolated from rats of 28-day simulated microgravity (SUS), countermeasure [S + D: SUS plus 1 h/d -G(x) to simulate intermittent artificial gravity (IAG)] and control (CON) groups. Three mechanical parameters were calculated: the overall stiffness (β), circumferential stress (σ(θ))-strain (ε(θ)) relationship and pressure-dependent incremental elastic modulus (E(inc,p)). Vessel wall collagen and elastin percentage were quantified by electron microscopy. The results demonstrate that the active mechanical behavior of MSAs differs noticeably among the three groups: the active stress-strain curve of SUS vessels is very close to the passive curve, whereas the active σ(θ)-ε(θ) curves of CON and S + D vessels are shifted leftward and display a parabolic shape, indicating that for MSAs isolated from S + D, but not those from SUS rats, the pressure-induced myogenic constriction can effectively stiffen the vessel wall as the CON vessels. The passive mechanical behavior of MSAs does not show significant differences among the three groups. However, the percentage of collagen is decreased in the wall of SUS and S + D compared with CON vessels in the following order: SUS < S + D < CON. Thus, the relationship between passive mechanical behavior and compositional changes may be complex and yet depends on factors other than the quantity of collagen and elastin. These findings have provided biomechanical data for the understanding of the mechanism of postflight orthostatic intolerance and its gravity-based countermeasure.     

Cyclic mechanical strain regulates the development of engineered smooth muscle tissue.

We show that the appropriate combinations of mechanical stimuli and polymeric scaffolds can enhance the mechanical properties of engineered tissues. The mechanical properties of tissues engineered from cells and polymer scaffolds are significantly lower than the native tissues they replace. We hypothesized that application of mechanical stimuli to engineered tissues would alter their mechanical properties. Smooth muscle tissue was engineered on two different polymeric scaffolds and subjected to cyclic mechanical strain. Short-term application of strain increased proliferation of smooth muscle cells (SMCs) and expression of collagen and elastin, but only when SMCs were adherent to specific scaffolds. Long-term application of cyclic strain upregulated elastin and collagen gene expression and led to increased organization in tissues. This resulted in more than an order of magnitude increase in the mechanical properties of the tissues.     

A biomimetic tubular scaffold with spatially designed nanofibers of protein/PDS® bio‐blends

Electrospun tubular conduit (4 mm inner diameter) based on blends of polydioxanone (PDS II®) and proteins such as gelatin and elastin having a spatially designed trilayer structure was prepared for arterial scaffolds. SEM analysis of scaffolds showed random nanofibrous morphology and well‐interconnected pore network. Due to protein blending, the fiber diameter was reduced from 800–950 nm range to 300–500 nm range. Fourier‐transform infrared spectroscopy (FTIR) and differential scanning calorimetry (DSC) results confirmed the blended composition and crystallinity of fibers. Pure PDS scaffold under hydrated state exhibited a tensile strength of 5.61 ± 0.42 MPa and a modulus of 17.11 ± 1.13 MPa with a failure strain of 216.7 ± 13%. The blending of PDS with elastin and gelatin has decreased the tensile properties. A trilayer tubular scaffold was fabricated by sequential electrospinning of blends of elastin/gelatin, PDS/elastin/gelatin, and PDS/gelatin (EG/PEG/PG) to mimic the complex matrix structure of native arteries. Under hydrated state, the trilayer conduit exhibited tensile properties (tensile strength of 1.77 ± 0.2 MPa and elastic modulus of 5.74 ± 3 MPa with a failure strain of 75.08 ± 10%) comparable to those of native arteries. In vitro degradation studies for up to 30 days showed about 40% mass loss and increase in crystallinity due to the removal of proteins and “cleavage‐induced crystallization” of PDS. Biotechnol. Bioeng. 2009; 104: 1025–1033. © 2009 Wiley Periodicals, Inc.     

In vivo estimation of the contribution of elastin and collagen to the mechanical properties in the human abdominal aorta: effect of age and sex

The mechanical properties of the aorta affect cardiac function and are related to cardiovascular morbidity/mortality. This study was designed to evaluate the isotropic (mainly elastin, elastin(iso)) and anisotropic (mainly collagen, collagen(ani)) material parameters within the human aorta in vivo. Thirty healthy men and women in three different age categories (23-30, 41-54, and 67-72 yr) were included. A novel mechanical model was used to identify the mechanical properties and the strain field with aid of simultaneously recorded pressure and radius in the abdominal aorta. The magnitudes of the material parameters relating to both the stiffness of elastin(iso) and collagen(ani) were in agreement with earlier in vitro studies. The load-bearing fraction attributed to collagen(ani) oscillated from 10 to 30% between diastolic and systolic pressures during the cardiac cycle. With age, stiffness of elastin(iso) increased in men, despite the decrease in elastin content that has been found due to elastolysis. Furthermore, an increase in stiffness of collagen(ani) at high physiological pressure was found. This might be due to increased glycation, as well as changed isoforms of collagen in the aortic wall with age. A marked sex difference was observed, with a much less age-related effect, both on elastin(iso) and collagen(ani) stiffness in women. Possible factors of importance could be the effect of sex hormones, as well as differing collagen isoforms, between the sexes.     

The elastic properties of a polyurethane arterial prosthesis

The relationship between the mechanical properties of a fibrous polyurethane arterial prosthesis and the graft manufacturing process variables was studied from uniaxial tensile tests. A non-linear model was used to characterize the cylindrical elastic properties. Experiments on cylindrical segments were carried out to determine the constitutive constants and to assess the applicability of the model to the polyurethane graft. The compliance of 4 mm internal diameter grafts with various wall-thicknesses was predicted. The results were used to produce grafts with compliance matched to that of the carotid and femoral arteries.     

A new constitutive model for multi-layered collagenous tissues

Collagenous tissues such as the aneurysmal wall or the aorta are multi-layered structures with the mean fibre alignments distinguishing one layer from another. A constitutive representation of the multiple collagen layers is not yet developed, and hence the aim of the present study. The proposed model is based on the constitutive theory of finite elasticity and is characterized by an anisotropic strain-energy function which takes the material structure into account. The passive tissue behaviour is modelled and the related mechanical response is assumed to be dominated by elastin and collagen. While elastin is modelled by the neo-Hookean material the constitutive response of collagen is assumed to be transversely isotropic for each individual layer and based on an exponential function. The proposed constitutive function is polyconvex which ensures material stability. The model has five independent material parameters, each of which has a clear physical interpretation: the initial stiffnesses of the collagen fabric in the two principal directions, the shear modulus pertaining to the non-collagenous matrix material, a parameter describing the level of nonlinearity of the collagen fabric, and the angle between the principal directions of the collagen fabric and the reference coordinate system. An extension-inflation test of the adventitia of a human femoral artery is simulated by means of the finite element method and an error function is minimized by adjusting the material parameters yielding a good agreement between the model and the experimental data.     

Biomechanical and morphological properties of the multiparous ovine vagina and effect of subsequent pregnancy

Pelvic floor soft tissues undergo changes during the pregnancy. However, the degree and nature of this process is not completely characterized. This study investigates the effect of subsequent pregnancy on biomechanical and structural properties of ovine vagina. Vaginal wall from virgin, pregnant (in their third pregnancy) and parous (one year after third vaginal delivery) Swifter sheep (n = 5 each) was harvested. Samples for biomechanics and histology, were cut in longitudinal axis (proximal and distal regions). Outcome measurements describing Young’s modulus, ultimate stress and elongation were obtained from stress-strain curves. For histology samples were stained with Miller's Elastica staining. Collagen, elastin and muscle cells and myofibroblasts contents were estimated, using image processing techniques. Statistical analyses were performed in order to determine significant differences among experimental groups. Significant regional differences were identified. The proximal vagina was stiffer than distal, irrespective the reproductive status. During the pregnancy proximal vagina become more compliant than in parous (+47.45%) or virgin sheep (+64.35%). This coincided with lower collagen (−15 to −21%), higher elastin (+30 to +60%), and more smooth muscle cells (+17 to +37%). Vaginal tissue from parous ewes was weaker than of virgins, coinciding with lower collagen (−10%), higher elastin (+50%), more smooth muscle cells (+20%). It could be proposed that after pregnancy biomechanical properties of vagina do not recover to those of virgins. Since elastin has a significant influence on the compliance of soft tissues and collagen is the main “actor” regarding strength, histological analysis performed in this study justifies the mechanical behavior observed.     

Tissue engineering of vascular grafts.

The challenge of tissue engineering blood vessels with the mechanical properties of native vessels, and with the anti-thrombotic properties required is immense. Recent advances, however, indicate that the goal of providing a tissue-engineered vascular graft that will remain patent in vivo for substantial periods of time, is achievable. For instance, collagen gels have been used to fabricate a tissue in vitro that is representative of a native vessel: an acellular collagen tubular structure, when implanted as a vascular graft, was able to function, and to become populated with host cells. A completely cellular approach culturing cells into tissue sheets and wrapping these around a mandel was able to form a layered tubular structure with impressive strength. Culture of cells onto a biodegradable scaffold within a dynamic bioreactor, generated a tissue-engineered vascular graft with substantial stiffness and, when lined with endothelial cells, was able to remain patent for up to 4 weeks in vivo. In our experiments, use of a non-degradable polyurethane scaffold and culture with smooth muscle cells generated a construct with mechanical properties similar to native vessels. This composite tissue engineered vascular graft with an endothelial layer formed using fluid shear stress to align the endothelial cells, was able to remain patent with an neointima for up to 4 weeks. These results show that tissue engineering of vascular grafts has true potential for application in the clinical situation.