Ultralow fouling polyacrylamide on gold surfaces via surface-initiated atom transfer radical polymerization

In this work, polyacrylamide is investigated as an ultralow fouling surface coating to highly resist protein adsorption, cell adhesion, and bacterial attachment. Polyacrylamide was grafted on gold surfaces via surface-initiated atom transfer radical polymerization (ATRP). Protein adsorption from a wide range of biological media, including single protein solutions of fibrinogen, bovine serum albumin, and lysozyme, dilute and undiluted human blood serum, and dilute and undiluted human blood plasma, was studied by surface plasmon resonance (SPR). Dependence of the protein resistance on polyacrylamide film thickness was examined. With the optimal film thickness, the adsorption amount of all three single proteins on polyacrylamide-grafted surfaces was <3 pg/mm(2), close to the detection limit of SPR. The average nonspecific adsorptions from 10% plasma, 10% serum, 100% plasma, and 100% serum onto the polyacrylamide-grafted surfaces were 5, 6.5, 17, and 28 pg/mm(2), respectively, comparable (if not better) than the adsorption levels on poly(ethylene glycol) (PEG) and zwitterionic poly(sulfobetaine methacrylate) surfaces, the best antifouling materials known to date. The polyacrylamide-grafted surfaces were also shown strongly resistant to adhesion from bovine aortic endothelial cells and two bacterial species, Gram-positive Staphylococcus epidermidis ( S. epidermidis ) and Gram-negative Pseudomonas aeruginosa ( P. aeruginosa ). Strong hydrogen bond with water is considered the key attribute for the ultralow fouling properties of polyacrylamide. This is the first work to graft gold surfaces with polyacrylamide brushes via ATRP to achieve ultralow fouling surfaces, demonstrating that polyacrylamide is a promising alternative to traditional PEG-based antifouling materials.     

Poly(HEMA) brushes emerging as a new platform for direct detection of food pathogen in milk samples

Surface plasmon resonance (SPR) biosensors capable of in real time detection of Cronobacter at concentrations down to 10? cells mL?1 in samples of consumer fresh-whole fat milk, powder whole-fat milk preparation, and powder infant formulation were developed for the first time. Antibodies against Cronobacter were covalently attached onto polymer brushes of poly(2-hydroxyethyl methacrylate) (poly(HEMA)) grafted from the SPR chip surface. The lowest detection limit, 10? cells mL?1, was achieved in phosphate buffered saline (pH 7.4) with sensors prepared by covalent immobilization of the same antibodies onto a self assembled monolayer (SAM) of hexa(ethylene glycol) undecanethiol (EG?). However, when the EG? based sensors were challenged with milk samples the non-specific response due to the deposition of non-targeted compounds from the milk samples was much higher than the specific response to Cronobacter hampering the detection in milk. Similar interfering fouling was observed on antifouling polymer brushes of hydroxy-capped oligoethylene glycol methacrylate and even a 10 times higher fouling was observed on the widely used SAM of mixed hydroxy- and carboxy-terminated alkanethiols. Only poly(HEMA) brushes totally suppressed the fouling from milk samples. The robust well-controlled surface initiated atom transfer radical polymerization of HEMA allowed the preparation of highly dense brushes with a minimal thickness so that the capture of antigens by the antibodies immobilized on the brush layer could take place close to the gold SPR surface to provide a stronger optical response while the fouling was still suppressed. A minimum thickness of 19 nm of poly(HEMA) brush layer was necessary to suppress completely non-specific sensor response to fouling from milk.     

Cell fouling resistance of polymer brushes grafted from ti substrates by surface-initiated polymerization: effect of ethylene glycol side chain length

This paper presents a comparative study on the antifouling properties of poly(ethylene glycol) (PEG)-based polymer coatings prepared by surface-initiated polymerization (SIP). Three types of poly(oligo(ethylene glycol) methyl ether methacrylate) (POEGMEMA) polymer thin films of approximate 100 nm thickness were grafted from a catechol initiator that was immobilized on a Ti substrate. OEGMEMA monomers containing side chains of 4, 9, and 23 EG units were used in surface-initiated atom transfer radical polymerization (SI-ATRP) to form POEGMEMA-4, -9, and -23 polymer brushes. The chemical composition, thickness, and wettability of the polymer brushes were characterized by X-ray photoelectron spectroscopy (XPS), ellipsometry, and static water contact angle measurements, respectively. The dependence of antifouling performance on EG side chain length was systemically tested and compared by 3T3 fibroblast cell adhesion assays. Results from 4-h cell culture experiments revealed the complete absence of cell attachment on all the grafted Ti substrates. Excellent cell fouling resistance continued with little dependence on EG side chain length up to three weeks, after which long-term antifouling performance depended on the EG chain length as the grafted samples reached confluent cell coverage in 7, 10, and 11 weeks for POEGMEMA-4, -9, and -23, respectively.     

Doubly biomimetic catecholic phosphorylcholine copolymer: a platform strategy for fabricating antifouling surfaces

A doubly biomimetic PMNC polymer bearing cell antifouling phosphorylcholine and mussel adhesive protein catechol groups is synthesized. The polymer can be deposited onto a variety of substrates by dip-coating in an aqueous solution, adhering to surfaces via the catechol functional group while at the same time forming a cell outer membrane mimetic antifouling surface. Contact angle, ATR-FTIR and XPS measurements confirm polymer coating formation on a variety of inorganic and organic substrates. BSA and bovine plasma fibrinogen protein adsorption on PMNC coated surfaces are reduced significantly compared to unmodified substrates, and platelet adhesion from human serum onto the PMNC coated substrate surfaces is highly suppressed in this study.     

Functional polymer brushes via surface-initiated atom transfer radical graft polymerization for combating marine biofouling

Dense and uniform polymer brush coatings were developed to combat marine biofouling. Nonionic hydrophilic, nonionic hydrophobic, cationic, anionic and zwitterionic polymer brush coatings were synthesized via surface-initiated atom transfer radical polymerization (SI-ATRP) of 2-hydroxyethyl methacrylate, 2,3,4,5,6-pentafluorostyrene, 2-(methacryloyloxy)ethyl trimethylammonium chloride, 4-styrenesulfonic acid sodium and N,N'-dimethyl-(methylmethacryloyl ethyl) ammonium propanesulfonate, respectively. The functionalized surfaces had different efficacies in preventing adsorption of bovine serum albumin (BSA), adhesion of the Gram-negative bacterium Pseudomonas sp. NCIMB 2021 and the Gram-positive Staphylococcus aureus, and settlement of cyprids of the barnacle Amphibalanus amphitrite (=Balanus amphitrite). The nonionic hydrophilic, anionic and zwitterionic polymer brushes resisted BSA adsorption during a 2?h exposure period. The nonionic hydrophilic, cationic and zwitterionic brushes exhibited resistance to bacterial fouling (24?h exposure) and cyprid settlement (24 and 48?h incubation). The hydrophobic brushes moderately reduced protein adsorption, and bacteria and cyprid settlement. The anionic brushes were least effective in preventing attachment of bacteria and barnacle cyprids. Thus, the best approach to combat biofouling involves a combination of nonionic hydrophilic and zwitterionic polymer brush coatings on material surfaces.     

Functional polymer brushes via surface-initiated atom transfer radical graft polymerization for combating marine biofouling

Dense and uniform polymer brush coatings were developed to combat marine biofouling. Nonionic hydrophilic, nonionic hydrophobic, cationic, anionic and zwitterionic polymer brush coatings were synthesized via surface-initiated atom transfer radical polymerization (SI-ATRP) of 2-hydroxyethyl methacrylate, 2,3,4,5,6-pentafluorostyrene, 2-(methacryloyloxy)ethyl trimethylammonium chloride, 4-styrenesulfonic acid sodium and N,N′-dimethyl-(methylmethacryloyl ethyl) ammonium propanesulfonate, respectively. The functionalized surfaces had different efficacies in preventing adsorption of bovine serum albumin (BSA), adhesion of the Gram-negative bacterium Pseudomonas sp. NCIMB 2021 and the Gram-positive Staphylococcus aureus, and settlement of cyprids of the barnacle Amphibalanus amphitrite (=Balanus amphitrite). The nonionic hydrophilic, anionic and zwitterionic polymer brushes resisted BSA adsorption during a 2 h exposure period. The nonionic hydrophilic, cationic and zwitterionic brushes exhibited resistance to bacterial fouling (24 h exposure) and cyprid settlement (24 and 48 h incubation). The hydrophobic brushes moderately reduced protein adsorption, and bacteria and cyprid settlement. The anionic brushes were least effective in preventing attachment of bacteria and barnacle cyprids. Thus, the best approach to combat biofouling involves a combination of nonionic hydrophilic and zwitterionic polymer brush coatings on material surfaces.     

Synthesis and characterization of poly(N-hydroxyethylacrylamide) for long-term antifouling ability

Development of biomaterials with long-term biocompatibility, durability, and stability remains a critical challenge for biomedical devices. Here, we synthesize, characterize, and graft poly(N-(2-hydroxyethyl)acrylamide) (polyHEAA) onto both gold surfaces and gold nanoparticles (AuNPs) via surface-initiated atom transfer radical polymerization (SI-ATRP) to form a stable antifouling coating to resist nonspecific protein adsorption and bacterial attachment. Surface plasmon resonance (SPR) results demonstrate that all of polyHEAA brushes coated on the gold substrate at a wide range of film thickness of ~10-40 nm can achieve almost zero protein adsorption from undiluted blood plasma and serum for 1 h, while static bacteria assay results show that polyHEAA brushes prohibit long-term bacterial colonization by Staphylococcus epidermidis and Escherichia coli RP437 up to 3 days. Moreover, the polyHEAA-coated AuNPs with different diameters remain their hydrodynamic sizes unchanged in human blood plasma and serum for up to 7 days. All these data indicate that polyHEAA can serve as promising biomaterials with long-term biocompatibility and durability suitable for applications in complex biological media.     

Generation of functional coatings on hydrophobic surfaces through deposition of denatured proteins followed by grafting from polymerization

Hydrophilic coatings were produced on flat hydrophobic substrates featuring n-octadecyltrichlorosilane (ODTS) and synthetic polypropylene (PP) nonwoven surfaces through the adsorption of denatured proteins. Specifically, physisorption from aqueous solutions of α-lactalbumin, lysozyme, fibrinogen, and two soy globulin proteins (glycinin and β-conglycinin) after chemical (urea) and thermal denaturation endowed the hydrophobic surfaces with amino and hydroxyl functionalities, yielding enhanced wettability. Proteins adsorbed strongly onto ODTS and PP through nonspecific interactions. The thickness of adsorbed heat-denatured proteins was adjusted by varying the pH, protein concentration in solution, and adsorption time. In addition, the stability of the immobilized protein layer was improved significantly after interfacial cross-linking with glutaraldehyde in the presence of sodium borohydride. The amino and hydroxyl groups present on the protein-modified surfaces served as reactive sites for the attachment of polymerization initiators from which polymer brushes were grown by surface-initiated atom-transfer radical polymerization of 2-hydroxyethyl methacrylate. Protein denaturation and adsorption as well as the grafting of polymeric brushes were characterized by circular dichroism, ellipsometry, contact angle, and Fourier transform infrared spectroscopy in the attenuated total reflection mode.     

Algal antifouling and fouling-release properties of metal surfaces coated with a polymer inspired by marine mussels

The marine antifouling and fouling-release performance of titanium surfaces coated with a bio-inspired polymer was investigated. The polymer consisted of methoxy-terminated poly(ethylene glycol) (mPEG) conjugated to the adhesive amino acid l-3,4-dihydroxyphenylalanine (DOPA) and was chosen based on its successful resistance to protein and mammalian cell fouling. Biofouling assays for the settlement and release of the diatom Navicula perminuta and settlement, growth and release of zoospores and sporelings (young plants) of the green alga Ulva linza were carried out. Results were compared to glass, a poly(dimethylsiloxane) elastomer (Silastic T2) and uncoated Ti. The mPEG-DOPA3 modified Ti surfaces exhibited a substantial decrease in attachment of both cells of N. perminuta and zoospores of U. linza as well as the highest detachment of attached cells under flow compared to control surfaces. The superior performance of this polymer over a standard silicone fouling-release coating in diatom assays and approximately equivalent performance in zoospore assays suggests that this bio-inspired polymer may be effective in marine antifouling and fouling-release applications.     

Micropatterning of polymer brushes: grafting from dewetting polymer films for biological applications

In this novel platform, a micropatterned polymer brush was obtained by grafting poly(poly(ethylene glycol) methyl ether methacrylate) (poly(PEGMA)) from a thin macroinitiator film using atom transfer radical polymerization (ATRP). A pattern of holes was formed in the macroinitiator film by taking advantage of its spontaneous dewetting above the glass transition temperature from a bottom polystyrene film, driven by unfavorable intermolecular forces. Patterning by dewetting can be achieved at length-scales from a few hundred nanometers to several tens of micrometers, by simply thermally annealing the bilayer above the glass transition temperature of the polymer. This approach is substrate-independent, as polymer films can be cast onto surfaces of different size, shape, or material. As a demonstration of its potential, proteins, and individual cells were attached on targeted bioadhesive polystyrene areas of the micropatterns within poly(PEGMA) protein-repellent brushes. We anticipate this approach will be suitable for the patterning of brushes, especially for biomedical applications such as in the study of single cells and of cell cocultures.     

Charged hydrophilic polymer brushes and their relevance for understanding marine biofouling

The resistance of charged polymers to biofouling was investigated by subjecting cationic (PDMAEMA), anionic (PSPMA), neutral (PHEMA-co-PEG₁₀MA), and zwitterionic (PSBMA) brushes to assays testing protein adsorption; attachment of the marine bacterium Cobetia marina; settlement and adhesion strength of zoospores of the green alga Ulva linza; settlement of barnacle (Balanus amphitrite and B. improvisus) cypris larvae; and field immersion tests. Several results go beyond the expected dependence on direct electrostatic attraction; PSPMA showed good resistance towards attachment of C. marina, low settlement and adhesion of U. linza zoospores, and significantly lower biofouling than on PHEMA-co-PEG₁₀MA or PSBMA after a field test for one week. PDMAEMA showed potential as a contact-active anti-algal coating due to its capacity to damage attached spores. However, after field testing for eight weeks, there were no significant differences in biofouling coverage among the surfaces. While charged polymers are unsuitable as antifouling coatings in the natural environment, they provide valuable insights into fouling processes, and are relevant for studies due to charging of nominally neutral surfaces.     

Surface properties and reduced biofouling of graft-copolymers that possess oppositely charged groups

Microbial biofilms and their components present a major obstacle for ensuring the long-term effectiveness of membrane processes. Graft polymerization on membrane surfaces, in general, and grafting with oppositely charged monomers, have been shown to reduce biofouling significantly. In this study, surface forces and macromolecular properties of graft copolymers that possess oppositely charged groups were related to their potent antibiofouling behavior. Graft polymerization was performed using the negatively charged 3-sulphopropyl methacrylate (SPM) and positively charged [2-(methacryloyloxy)ethyl]-trimethylammonium (MOETMA) monomers to yield a copolymer layer on polyvinylidene fluoride (PVDF) surface. Quartz crystal microbalance with dissipation monitoring (QCM-D) technology was used to monitor the reduced adsorption of extracellular polymeric substances (EPS) extracted from a membrane bioreactor (MBR) wastewater treatment facility. Complemented measurements of attenuated total reflection Fourier transform infrared (ATR-FTIR) spectroscopy provided evaluation of the antifouling properties of the surface. Increase in water content in grafted layer exposed to 100 mM aqueous NaCl solution was observed by QCM-D. Therefore, the grafted copolymer layer is swelled in the presence of 100 mM NaCl because of reversing of polymer self-association by counterions. Force measurements by atomic force microscopy (AFM) showed an increased repulsion between a carboxylate-modified latex (CML) particle probe and a modified PVDF surface, especially in the presence of 100 mM NaCl. The hydration and swelling of the grafted polymer layer are shown to repel EPS and reduce their adsorption. Delineating the surface properties of antifouling grafted layers may lead to the design of novel antifouling surfaces.     

Sediment challenge to promising ultra-low fouling hydrophilic surfaces in the marine environment

Hydrophilic coatings exhibit ultra-low fouling properties in numerous laboratory experiments. In stark contrast, the antifouling effect of such coatings in vitro failed when performing field tests in the marine environment. The fouling release performance of nonionic and zwitterionic hydrophilic polymers was substantially reduced compared to the controlled laboratory environment. Microscopy and spectroscopy revealed that a large proportion of the accumulated material in field tests contains inorganic compounds and diatomaceous soil. Diatoms adhered to the accumulated material on the coating, but not to the pristine polymer. Simulating field tests in the laboratory using sediment samples collected from the test sites showed that incorporated sand and diatomaceous earth impairs the fouling release characteristics of the coatings. When exposed to marine sediment from multiple locations, particulate matter accumulated on these coatings and served as attachment points for diatom adhesion and enhanced fouling. Future developments of hydrophilic coatings should consider accumulated sediment and its potential impact on the antifouling performance.     

Stability and nonfouling properties of poly(poly(ethylene glycol) methacrylate) brushes under cell culture conditions

This paper investigates the stability and nonfouling properties of poly(poly(ethylene glycol) methacrylate) (PPEGMA) brushes prepared by surface-initiated atom transfer radical polymerization from SiO(x) substrates modified with a trimethoxysilane-based ATRP initiator. At high chain densities, PPEGMA brushes were found to detach rapidly from glass or silicon substrates. Detachment of the PPEGMA brushes could be monitored with contact angle measurements, which indicated a decrease in the receding water contact angle upon detachment. Detachment of the PPEGMA brushes also resulted in an increase in nonspecific protein adsorption. The stability, and as a consequence the long-term nonfouling properties, of the PPEGMA brushes could be improved by tailoring the brush density and, to a lesser extent, the molecular weight of the polymer chains. By appropriate decrease of the grafting density, the stability of the brushes in cell culture medium could be improved from less than 1 to more than 7 days, without compromising the nonfouling properties.     

Antifouling potential of Subtilisin A immobilized onto maleic anhydride copolymer thin films

The proteinaceous nature of the adhesives used by most fouling organisms to attach to surfaces suggests that coatings incorporating proteolytic enzymes may provide a technology for the control of biofouling. In the present article, the antifouling (AF) and fouling release potential of model coatings incorporating the surface-immobilized protease, Subtilisin A, have been investigated. The enzyme was covalently attached to maleic anhydride copolymer thin films; the characteristics of the bioactive coatings obtained were adjusted through variation of the type of copolymer and the concentration of the enzyme solution used for immobilization. The bioactive coatings were tested for their effect on the settlement and adhesion strength of two major fouling species: the green alga Ulva linza and the diatom Navicula perminuta. The results show that the immobilized enzyme effectively reduced the settlement and adhesion strength of zoospores of Ulva and the adhesion strength of Navicula cells. The AF efficacy of the bioactive coatings increased with increasing enzyme surface concentration and activity, and was found to be superior to the equivalent amount of enzyme in solution. The results provide a rigorous analysis of one approach to the use of immobilized proteases to reduce the adhesion of marine fouling organisms and are of interest to those investigating enzyme-containing coating technologies for practical biofouling control.     

Polymer brush controlled bioinspired calcium phosphate mineralization and bone cell growth

Polymer brushes on thiol-modified gold surfaces were synthesized by using terminal thiol groups for the surface-initiated free radical polymerization of methacrylic acid and dimethylaminoethyl methacrylate, respectively. Atomic force microscopy shows that the resulting poly(methacrylic acid) (PMAA) and poly(dimethylaminoethyl methacrylate) (PDMAEMA) brushes are homogeneous. Contact angle measurements show that the brushes are pH-responsive and can reversibly be protonated and deprotonated. Mineralization of the brushes with calcium phosphate at different pH yields homogeneously mineralized surfaces, and preosteoblastic cells proliferate on both the nonmineralized and mineralized surfaces. The number of living cells on the mineralized hybrid surfaces is ca. 3 times (PDMAEMA) and 10 times (PMAA) higher than on the corresponding nonmineralized brushes.     

Layer-by-Layer Click Deposition of Functional Polymer Coatings for Combating Marine Biofouling

"Click" chemistry-enabled layer-by-layer (LBL) deposition of multilayer functional polymer coatings provides an alternative approach to combating biofouling. Fouling-resistant azido-functionalized poly(ethylene glycol) methyl ether methacrylate-based polymer chains (azido-poly(PEGMA)) and antimicrobial alkynyl-functionalized 2-(methacryloyloxy)ethyl trimethyl ammonium chloride-based polymer chains (alkynyl-poly(META)) were click-assembled layer-by-layer via alkyne-azide 1,3-dipolar cycloaddition. The polymer multilayer coatings are resistant to bacterial adhesion and are bactericidal to marine Gram-negative Pseudomonas sp. NCIMB 2021 bacteria. Settlement of barnacle ( Amphibalanus (= Balanus ) amphitrite ) cyprids is greatly reduced on the multilayer polymer-functionalized substrates. As the number of the polymer layers increases, efficacy against bacterial fouling and settlement of barnacle cyprids increases. The LBL-functionalized surfaces exhibit low toxicity toward the barnacle cyprids and are stable upon prolonged exposure to seawater. LBL click deposition is thus an effective and potentially environmentally benign way to prepare antifouling coatings.     

Mechanical factors favoring release from fouling release coatings

For some twenty years the marine coatings industry has been intrigued by polymer surfaces with low adhesion to other materials, especially to the biological glues used by marine organisms. Polymers with fouling release surfaces have been made from sundry materials, and their resistance to marine fouling in both static and dynamic tests has been evaluated in the world's oceans. Although the polymer surface property most frequently correlated with bioadhesion is its critical surface tension (γ(?)), resistance to fouling is also influenced by other bulk and surface properties of the polymer. This paper reviews the types of bonding associated with polymeric materials used in fouling resistant coatings, describes the removal process in terms of fracture mechanics, and discusses the importance of surface energy, elastic modulus and coating thickness in the release of biofoulants.     

Effect of polymer brush architecture on antibiofouling properties

Polymer brushes show great promise in next-generation antibiofouling surfaces. Here, we have studied the influence of polymer brush architecture on protein resistance. By carefully optimizing reaction conditions, we were able to polymerize oligoglycerol-based brushes with sterically demanding linear or dendronized side chains on gold surfaces. Protein adsorption from serum and plasma was analyzed by surface plasmon resonance. Our findings reveal a pronounced dependence of biofouling on brush architecture. Bulky yet flexible side chains as in dendronized brushes provide an ideal environment to repel protein-possibly through formation of a hydration layer, which can be further enhanced by presenting free hydroxyl groups on the polymer brushes. A deeper understanding of how brush architecture influences protein resistance will ultimately enable fabrication of surface coatings tailored to specific requirements in biomedical applications.