Development of a bioartificial nerve graft. I. Design based on a reaction-diffusion model

A simple reaction-diffusion model has been developed to describe the mass transport of nutrients and nerve growth factor within a bioartificial nerve graft (BNG). The BNG consists of a porous polymer conduit that is preseeded with Schwann cells in its lumen. The Schwann cells produce growth factors to stimulate nerve regeneration within the lumen of the conduit. The model can predict the wall thickness, porosity, and Schwann cell seeding density needed to maximize the axon extension rate while ensuring that sufficient nutrients, especially oxygen, are made available to the neurons until the formation of the neovasculature. The model predicts a sixteen-fold increase in the levels of nerve growth factor by dropping the porosity from 95 to 55% but only at the expense of reducing the oxygen concentration. At higher porosities, increasing the wall thickness and increasing the Schwann cell seeding density both have the same effect of increasing the concentration of nerve growth factor within the lumen of the conduit. This model provides a simple tool for evaluating various conduit designs before continuing with experimental studies in vivo.     

Development of a bioartificial nerve graft. II. Nerve regeneration in vitro

A promising alternative for the repair of peripheral nerve injuries is the bioartificial nerve graft, or BNG, comprised of a tubular conduit preseeded with Schwann cells, which are an effective substrate for enhancing nerve regeneration. The physical properties of the conduit, porosity and wall thickness, as well as the Schwann cell seeding density, were tested for their effect on axon growth using rat dorsal root ganglia. These parameters can influence the amount of nutrients and growth factors made available to the neural tissue. Results show that a greater wall thickness and lower porosities have a detrimental effect on the growth of the axons. Over a four week period, axons extended 3.2 mm for the optimum case (DeltaR = 0.82 mm, epsilon = 0.75) compared to 1.8 and 1.6 mm for a lower porosity (0.55) and a greater wall thickness (1.4 mm), respectively. A maximum in the growth rate occurs at a porosity of 75% for Schwann cell seeded conduits but not for unseeded ones. When compared to mass transfer predictions, the results suggest that, at higher porosities, more growth factors diffuse out of the conduit, while at low porosities there is competition for nutrients. Increasing the Schwann cell seeding density enhances growth but also leads to an increase in the number of axons along the length of the conduit. This is indicative of branching of the axons, which requires additional resources to maintain and can lead to painful neuroma formation. Wall thickness and porosity were found not to have any significant effect on the axon number sprouting from the dorsal root ganglia and the mean diameter (p > 0.05). Considerations need to be made, not just on the polymer used, but also on its porosity, wall thickness, and Schwann cell seeding density. These parameters can be adjusted to create a bioartificial nerve graft that provides the optimal environment for nerve growth.     

Comparative life cycle assessment of fired brick production in Thailand

The International Journal of Life Cycle Assessment - Fired bricks are an essential construction material in Thailand where the majority of fired brick kilns use rice husk as feedstock. Given the...     

Potential Use of Porous Titanium–Niobium Alloy in Orthopedic Implants: Preparation and Experimental Study of Its Biocompatibility In Vitro

Background

The improvement of bone ingrowth into prosthesis and enhancement of the combination of the range between the bone and prosthesis are important for long-term stability of artificial joints. They are the focus of research on uncemented artificial joints. Porous materials can be of potential use to solve these problems.

Objectives/Purposes

This research aims to observe the characteristics of the new porous Ti-25Nb alloy and its biocompatibility in vitro, and to provide basic experimental evidence for the development of new porous prostheses or bone implants for bone tissue regeneration.

Methods

The Ti-25Nb alloys with different porosities were fabricated using powder metallurgy. The alloys were then evaluated based on several characteristics, such as mechanical properties, purity, pore size, and porosity. To evaluate biocompatibility, the specimens were subjected to methylthiazol tetrazolium (MTT) colorimetric assay, cell adhesion and proliferation assay using acridine staining, scanning electron microscopy, and detection of inflammation factor interleukin-6 (IL-6).

Results

The porous Ti-25Nb alloy with interconnected pores had a pore size of 200 µm to 500 µm, which was favorable for bone ingrowth. The compressive strength of the alloy was similar to that of cortical bone, while with the elastic modulus closer to cancellous bone. MTT assay showed that the alloy had no adverse reaction to rabbit bone marrow mesenchymal stem cells, with a toxicity level of 0 to 1. Cell adhesion and proliferation experiments showed excellent cell growth on the surface and inside the pores of the alloy. According to the IL-6 levels, the alloy did not cause any obvious inflammatory response.

Conclusion

All porous Ti-25Nb alloys showed good biocompatibility regardless of the percentage of porosity. The basic requirement of clinical orthopedic implants was satisfied, which made the alloy a good prospect for biomedical application. The alloy with 70% porosity had the optimum mechanical properties, as well as suitable pore size and porosity, which allowed more bone ingrowth.     

MC3T3-E1 osteoblast attachment and proliferation on porous hydroxyapatite scaffolds fabricated with nanophase powder

Porous bone tissue engineering scaffolds were fabricated using both nano hydroxyapatite (nano HA) powder (20 nm average particle size) and micro HA powder (10 microm average particle size), resulting in sintered scaffolds of 59 vol% porosity and 8.6 +/- 1.9 microm average grain size and 72 vol% porosity and 588 +/- 55nm average grain size, respectively. Scanning electron microscopy was used to measure both the grain size and pore size. MC3T3-E1 osteoblast (OB) attachment and proliferation on both nano HA and micro HA porous scaffolds were quantified. As expected, OB cell number was greater on nano HA scaffolds compared with similarly processed micro HA scaffolds 5 days after seeding, while OB attachment did not appear greater on the nano HA scaffolds (p < 0.05).     

Air-filled porosity and permeability relationships during solid-state fermentation

An experimental apparatus was constructed to measure the structural parameters of organic porous media, i.,e. mechanical strength, air-filled porosity, air permeability, and the Ergun particle size. These parameters are critical to the engineering of aerobic bioconversion systems and were measured for a straw--manure mixture before and after 13 days of in-vessel composting. Porosity was measured using air pycnometry at four (day 0) and five (day 13) moisture levels, with each moisture level tested at a range of different densities. Tested wet bulk densities varied with moisture level, but dry bulk densities generally ranged from 100 to 200 kg m(-3). At each moisture/density combination, pressure drop was measured at airflow rates ranging from 0.001 to 0.05 m sec(-1), representing the range of airflow rates found in both intensive and extensive composting. Measured air-filled porosities were accurately predicted from measurements of bulk density, moisture, and organic matter content. Reductions in air-filled porosity at increasing moisture content were accompanied by an increase in permeability, apparently due to aggregations of fines. This aggregation was quantified by calculating an effective particle size from the Ergun permeability relationship, which increased from 0.0002 m at 50% moisture to 0.0021 m at 79% moisture. The range of airflow velocities reported in composting systems requires consideration of the second-order drag force term, particularly at velocities approaching 0.05 m s(-1) for the higher moisture treatments tested. Calculated permeabilities for the matrix ranged from 10(-10) to 10(-7) m2, varying with both air-filled porosity and moisture. Mechanical strength characterization provided a means to predict the effects of compaction on air-filled porosity and permeability of porous media beds. The results of this investigation extend porous media theory to the organic matrices common in solid-state fermentations and help build a framework for quantitative and mechanistic engineering design.     

Different Porosities of Chitosan Can Influence the Osteogenic Differentiation Potential of Stem Cells

Scaffolds porosity has an important role in in vitro and in vivo differentiation process of stem cells with given the amount of space available to the cells to proliferate and differentiate. In the present study, chitosan with three porosities including 10%, 15%, and 20% that created by gelatin were used for investigation of the proliferation and osteogenic differentiation potential of adipose‐derived stem cells (ADSCs). In order to be more like the scaffold to natural bone tissue, freeze‐drying method was used in the scaffold preparation. Scaffold morphology, cell attachment, and toxicity were evaluated using scanning electron microscopy and MTT assay. Then, osteogenic differentiation potential of ADSCs cultured on chitosan with different porosities was evaluated by common osteogenic markers such as Alizarin red staining, ALP activity, calcium content, and osteogenic‐related genes expression via real‐time RT‐PCR. Although all scaffolds supported the proliferation and differentiation of ADSCs, but 10% scaffold demonstrated higher amount of osteogenic markers in comparison with the other porosities and control groups. Taking together, it can be concluded that osteogenic differentiation well done in the scaffolds with lower porosity because density of the cells will increase by forcing resulted from the scaffold, so osteogenic differentiation of the stem cells have an inverse association with scaffold porosity. J. Cell. Biochem. 119: 625–633, 2018. © 2017 Wiley Periodicals, Inc.     

Modifications of nonwoven polyethylene terephthalate fibrous matrices via NaOH hydrolysis: Effects on pore size, fiber diameter, cell seeding and proliferation

A simple NaOH treatment method was developed for fabricating nonwoven fibrous matrices of polyethylene terephthalate (PET) with predictable porosity, pore size, and fiber diameter. Matrices with various porosities (90–97%), fiber diameters (13.5–25 μm), and pore sizes (54–65 μm) were prepared by treating with 1N NaOH at 70 °C for up to 120 h, resulting in up to 70% hydrolysis of the PET polymer. The hydrolysis of PET polymer by NaOH was found to follow a second-order kinetics with respect to the fiber surface area. Accordingly, mathematical models were developed to predict matrix porosity, fiber diameter, and apparent pore size of the PET matrices. The exponential decay coefficient of PET polymer was found to be 0.0147 h⁻¹. The matrices were used to study the effects of pore size and fiber diameter on cell seeding and proliferation. The seeding study demonstrated that cell adhesion on PET fibers can be enhanced, largely due to the increased surface roughness of the PET fibers. Decreasing the fiber diameter increases the surface curvature of the fibers and decreases available surface area for cell attachment, which, however, only resulted in a small decrease in the cell growth rate.     

Prevascularization of porous biodegradable polymers

Highly porous biocompatible and biodegradable polymers in the form of cylindrical disks of 13.5 mm diameter were implanted in the mesentery of male syngeneic Fischer rats for a period of 35 days to study the dynamics of tissue ingrowth and the extent of tissue vascularity, and to explore their potential use as substrates for cell transplantation. The advancing fibrovascular tissue was characterized from histological sections of harvested devices by image analysis techniques. The rate of tissue ingrowth increased as the porosity and/or the pore size of the implanted devices increased. The time required for the tissue to fill the device depended on the polymer crystallinity and was smaller for amorphous polymers. The vascularity of the advancing tissue was consistent with time and independent of the biomaterial composition and morphology. Poly(L-lactic acid) (PLLA) devices of 5 mm thickness, 24.5% crystallinity, 83% porosity, and 166 mum median pore diameter were filled by tissue after 25 days. However, the void volume of prevascularized devices (4%) was minimal and not practical for cell transplantation. In contrast, for amporphous PLLA devices of the same dimensions, and the similar porosity of 87% and median pore diameter of 179 mum, the tissue did not fill completely prevascularized devices, and an appreciable percentage (21%) of device volume was still available for cell engraftment after 25 days of implantation. These studies demonstrate the feasibility of creating vascularized templates of amorphous biodegradable polymers for the transplantation of isolated or encapsulated cell populations to regenerate metabolic organs and tissues. (c) 1993 John Wiley & Sons, Inc.     

Predicting permeability of regular tissue engineering scaffolds: scaling analysis of pore architecture,scaffold length,and fluid flow rate effects

The main aim of this research is to numerically obtain the permeability coefficient in the cylindrical scaffolds. For this purpose, a mathematical analysis was performed to derive an equation for desired porosity in terms of morphological parameters. Then, the considered cylindrical geometries were modeled and the permeability coefficient was calculated according to the velocity and pressure drop values based on the Darcy’s law. In order to validate the accuracy of the present numerical solution, the obtained permeability coefficient was compared with the published experimental data. It was observed that this model can predict permeability with the utmost accuracy. Then, the effect of geometrical parameters including porosity, scaffold pore structure, unit cell size, and length of the scaffolds as well as entrance mass flow rate on the permeability of porous structures was studied. Furthermore, a parametric study with scaling laws analysis of sample length and mass flow rate effects on the permeability showed good fit to the obtained data. It can be concluded that the sensitivity of permeability is more noticeable at higher porosities. The present approach can be used to characterize and optimize the scaffold microstructure due to the necessity of cell growth and transferring considerations.     

Effect of starting material particle size on its agglomeration behavior in high shear wet granulation

The effect of anhydrous lactose particle size distribution on its performance in the wet granulation process was evaluated. Three grades of anhydrous lactose were used in the study: “as is” manufacturer grade and 2 particle size fractions obtained by screening of the 60M lactose. Particle growth behavior of the 3 lactose grades was evaluated in a high shear mixer. Compactibility and porosity of the resulting granules were also evaluated. A uniaxial compression test on moist agglomerates of the 3 lactose grades was performed in an attempt to explain the mechanism of particle size effect observed in the high shear mixer. Particle growth of anhydrous lactose in the high shear mixer was inversely related to the particle size of the starting material. In addition, granulation manufactured using the grade with the smallest particle size was more porous and demonstrated enhanced compactibility compared with the other grades. Compacts with similar porosity and low liquid saturation demonstrated brittle behavior and their breakage strength was inversely related to lactose particle size in the uniaxial compression test, suggesting that material with smaller particle size may exhibit more pronounced nucleation behavior during wet granulation. On the other hand, compacts prepared at higher liquid saturation and similar compression force exhibited more plastic behavior and showed lower yield stress for the grade with smallest particle size. The lower yield stress of compacts prepared with this grade may indicate a higher coalescence tendency for its granules during wet granulation.     

Growth substrates made from duck excreta enriched wood shavings and source-separated municipal solid waste compost and separates: physical and chemical characteristics

Production and use of compost is an effective means to reduce wastes, and offers a large potential as growth substrates and source of nutrients. The objective of this study was to determine the physical and chemical characteristics of duck excreta enriched wood shavings (DMC) and source-separated municipal solid waste (MSW) composts and separates, and to assess the physical characteristics of growth substrates made from these two composts and selected substrates. MSW compost separates were the following sizes: F1 > 4 mm diameter, 2 mm < F2 < 4 mm, 1 mm < F3 < 2 mm and F4 < 1 mm. Growth substrates were prepared by mixing DMC and F2 and F3 MSW separates (M/M ratios). Growth substrates A-E consisted exclusively of 10-60% DMC and 20-60% of MSW separates F2 and F3. Growth substrates F-J, and K-O were the same as substrates A E, with 15% M/M brick fragments or shredded plastic added as porosity agents, respectively. Growth substrates (BE/S) made of black earth (BE) and sandy loam soil (Ls) in a 1:4 (M/M) ratio, commercially available peat substrate (Pr) and an in-house sphagnum peat-based substrate (Gs) were used for comparison. Principal component analysis (PCA) showed that DMC was a better material than MSW with respect to porosity and water field capacity. MSW compost and separates differed by their relatively high levels of water-soluble and HCl-hydrolyzable N and increased advantageous water retention capacity. PCA also showed that substrates A-E exhibited porosity and water field capacity similar to those of Pr. Substrates F-J had porosity and water field capacity similar to those of BE/S, whereas substrates K O were more similar to Pr and to substrates A and B. The presented data indicate that DMC and MSW separates were complementary in providing good physical and chemical characteristics to the growth substrates.     

Radiographic inspection of porosity in pure titanium dumbbell castings

Radiographic inspection of porosity in pure titanium dumbbell castings Background: Titanium frameworks are frequently indicated for implant supported prostheses; however, voids are usually encountered inside cast titanium. Objective: This study aimed to confirm the efficacy of a radiographic technique for inspection of porosity in commercially pure titanium castings with different diameter. Materials and methods: Sixty dumbbell rods (n = 20) with a central 1.5, 2.0 and 3.5 mm diameter were prepared by lost‐wax casting. Cast specimens were finished and polished and submitted to radiographic examination (90 kV, 15 mA, 0.6 s and 10–13 mm of distance) using periapical film. The radiographs were visually analysed for the presence of porosity in the extension of the dumbbell or in the central portion of the rods. Data were submitted to Pearson Chi‐square test (5%). Results: The tested radiographic method proved to be suitable for the evaluation of cast frameworks. Internal porosities were observed in most of the specimens (91.7%) (p = 0.0005); however, only 20% occurred on the central portion of the rods (p = 0.612). Conclusion: Internal porosities can be visualised through radiographs and occur mostly in small diameter structures. The radiographic evaluation of metal structures can improve the quality of frameworks and thereby potentially increase the longevity of the rehabilitation.     

Pore Direction in Relation to Anisotropy of Mechanical Strength in a Cubic Starch Compact

The purpose of this research was to evaluate the relation between preferential direction of pores and mechanical strength of cubic starch compacts. The preferential pore direction was quantified in SEM images of cross sections of starch compacts using a previously described algorithm for determination of the quotient of transitions (Q). This parameter and the mechanical strength were evaluated in compacts of different porosities. Starch was chosen as a model compound for materials with ductile behaviour of which tablets with low porosities can be made and which shows some elastic recovery after compaction. At medium and high porosity Q was significantly higher in the images providing a side view of the compact than in the images providing a top view (0.973 vs. 0.927 and 0.958 vs. 0.874 at 0 mm from the side of the compact and 0.956 vs. 0.854 and 0.951 vs. 0.862 at 3.5 mm), indicating that the pores were mainly oriented in the direction perpendicular to the direction of compression. This was accompanied by a lower crushing force in this direction. This could be explained by considering the pores as cracks which propagate through the sample during crushing. For both directions the crushing force decreased with increasing porosity. The yield strength of the compacts also decreased with increasing porosity, but this parameter was not dependent on the direction of crushing when the porosity was below 10%. The results show that pore direction significantly influences the crushing force but does not influence the yield strength, at porosities below 10%.     

Effect of particle size distribution on filtration performance of cell culture medium

Cell culture media used in CHO-based biologic processes are typically sterile filtered to prevent microbial contamination prior to inoculation. In this study, the impact of common sterile filter throughput on a different, commercially available cell culture media was evaluated from the intermediate-adsorption fouling model of the filtration model. The key particle size range for optimum filter performance was discussed and identified by measuring the submicron order particle size distribution. It may be possible to predict the performance of filter capacity with size-exclusive separation by understanding the media particle counts and size distribution.     

多孔钛合金不同孔径大小对新骨长入的影响

目的:评价不同孔径多孔钛合金植入物在骨缺损区对新骨长入的影响。方法:采用电子束熔融(EBM)技术制备三种不同孔径(孔径分别为1.0 mm,2.0 mm,3.0 mm)的多孔钛合金材料,其孔隙率依次为73%,79%,86%。将18只家犬随机分为1.0 mm孔径材料组,2.0 mm孔径材料组,3.0 mm孔径材料组,每组6只。制备家犬双侧股骨外侧髁缺损模型,然后植入各孔径组材料,于术后4周,8周,12周分别行大体标本观察,X线片观察,组织形态学观察三组不同孔径材料与周围骨的整合情况及孔隙中的新骨长入情况。结果:通过大体标本观察和X线片观察显示,12周后三组材料均与周围紧密骨连接。其中1.0 mm孔径组材料中心明显成骨,2.0 mm孔径组和3.0 mm孔径组中心仍为较多白色组织填充。组织学观察显示,12周时2.0 mm孔径组和3.0 mm孔径组材料周围有骨质包绕,但中心空洞,基本无骨质形成。1.0 mm孔径组材料周围骨质包绕紧密,孔中新生骨形成较多,且有大量纤维母细胞和软骨细胞形成。各时间点1.0 mm孔径组新生骨面积百分比明显高于2.0 mm孔径组和3.0 mm孔径组,P<0.01,差异具有统计学意义。2.0 mm孔径组和3.0 mm孔径组相比,P>0.05,无显著差异。结论:孔径大小影响多孔钛合金材料的骨长入,适当孔径的设计将更有利于材料的传导成骨。     

Effects of stent porosity on hemodynamics in a sidewall aneurysm model

Computation and experiment have been complementarily performed to study the fluid flow inside a stented lateral aneurysm anchored on the straight parent vessel. The implicit solver was based on the time-dependent incompressible Navier-Stokes equations of laminar flow. Solutions were generated by a cell-center finite-volume method that used second-order upwind and second-order center flux difference splitting for the convection and diffusion term, respectively. The second-order Crank-Nicolson method was used in the time integration term. Experimental techniques used were flow visualization (FV) and particle tracking velocimetry (PTV). Experimentally, the straight afferent vessel had an inner diameter 10mm. The diameters of the aneurysmal orifice, neck, and fundus were 14, 10, and 15 mm, respectively, and the distance between the orifice and dome measured 20mm. A 30 mm long helix-shaped stent was tested. Four stent porosities of 100%, 70%, 50%, and 25% were examined. Volume-flow rate waveform of a cerebral artery was considered with a maximum Reynolds number of 250 and Womersley number of 3.9. Results are presented in terms of the pulsatile main and secondary flow velocity vector fields, the volume inflow rates into the aneurysm, and the wall shear stress (WSS) and wall pressure at the aneurysm dome. Some comparisons of computed results with the present FV and PTV results and with the data available from the literature are also made. The maximum flow velocity inside the aneurysm ostium and the WSS in the dome region at the peak flow can, respectively, be suppressed to less than 5% of the parent vessel bulk velocity (or 20% of the unstented case) and 8% of the unstented case if the stent porosity is smaller than 40% (about the porosity of the two-layer stents). In general, the three-layer stents seem not as effective as the two-layer stents in reducing the magnitude of aneurysm inflow rate and WSS.     

Characteristics of immobilized yeast reactors producing ethanol from glucose

The evolutionary performance of up flow reactors are affected by the cell immobilization matrix and the matrix particle size distribution. Higher productivities are obtained using a low-density brick with a particle size of ca. 400-1400 mum. A medium condition favoring growth quickly leads to large biomass gradients within the reactors and, eventually, reductions in average productivities due to bed plugging. These systems can be accurately modelled using Monod kinetics when dispersion and the biomass gradient are considered. The productivity was apparently not controlled by substrate diffusion in these cases.     

Cell colonization in degradable 3D porous matrices

Cell colonization is an important in a wide variety of biological processes and applications including vascularization, wound healing, tissue engineering, stem cell differentiation and biosensors. During colonization porous 3D structures are used to support and guide the ingrowth of cells into the matrix. In this review, we summarize our understanding of various factors affecting cell colonization in three-dimensional environment. The structural, biological and degradation properties of the matrix all play key roles during colonization. Further, specific scaffold properties such as porosity, pore size, fiber thickness, topography and scaffold stiffness as well as important cell material interactions such as cell adhesion and mechanotransduction also influence colonization.Key words: colonization, pore size, porosity, topography, mechanotransduction, degradation, matrix turnover