谷氨酸棒状杆菌合成5-氨基乙酰丙酸的途径构建与发酵优化

5-氨基乙酰丙酸(5-amino levulinic acid,ALA)是生物体内天然存在的一种非蛋白质氨基酸,在农业和医药等领域应用广泛。为了在谷氨酸棒状杆菌中建立ALA碳四合成途径并优化其发酵体系,首先在谷氨酸棒状杆菌中过表达沼泽红假单胞菌来源的ALA合成酶(ALAS),建立高效的ALA碳四合成途径,然后从不同发酵培养基的比较、诱导剂和底物甘氨酸的浓度以及初始接种量等不同方面对ALA摇瓶发酵工艺进行了优化。结果显示,过表达Hem A的13032/p ZWA1菌株ALA产量达到1.41 g/L,是对照菌株的67.14倍。ALA的最优摇瓶发酵条件为以酵母粉为氮源的M9培养基,采用5%的接种量0.1 mmol/L IPTG进行Hem A的诱导表达,体系中甘氨酸的浓度要控制在4 g/L,摇瓶中ALA产量可达到3.28 g/L,比优化前提高了132.62%。采用发酵优化的条件,在5 L发酵罐的放大发酵中ALA产量可达10.08 g/L,这是现有报道中谷氨酸棒状杆菌一步发酵合成ALA的最高产量。     

重组大肠杆菌高效分泌表达β-木糖苷酶发酵条件的优化

[目的]嗜热拟青霉β-木糖苷酶基因在大肠杆菌中高效分泌表述重组β-木糖哥酶摇瓶发酵条件优化,及5 L发酵罐放大培养.[方法]通过单因素试验对诱导剂种类及其添加量、诱导起始 OD600、培养温度、培养时间进行优化研究.[结果]摇瓶优化结果表明:2％乳糖为诱导剂、培养温度为33℃C、OD600控制在0.8-0.9时诱导为最佳产酶条件,在此条件下培养48 h后胞外酶活达到103.9 U/mL,胞外分泌的比例高达99％以上.进行5L发酵罐放大培养,发酵48 h胞外酶活达到最高值392.5 U/mL,蛋白含量为10.1 g/L.[结论]该重组大肠杆菌高效分泌β-木糖苷酶,具有较好的工业化生产前景.     

重组大肠杆菌产尿素酶B高密度发酵条件的优化

探究重组大肠杆菌产尿素酶B（urease B subunit, UreB）的高密度发酵条件。通过实验室摇瓶和30 L发酵罐对UreB基因工程菌的发酵条件进行优化。结果表明：30 L发酵罐中以TB培养基为发酵培养基,接种量为5%,发酵温度为37 ℃,pH为6.8,溶氧量为30%左右,培养至2 h开始恒速流加50%甘油,4 h流加50%酵母提取物和50%胰蛋白胨,并加入终浓度为0.5 mmol/L的异丙基β-D-硫代半乳糖苷（isopropyl β-D-thiogalactoside,IPTG),诱导表达4 h,结束发酵,所得菌体干物质约为25.7 g/L,UreB表达量为31.4%。此工艺可以提高UreB的产量。     

重组巴斯德毕赤酵母高密度发酵表达植酸酶

对巴斯德毕赤酵母的高密度发酵条件进行了试验,并根据摇瓶发酵的优化结果进行了补料方式的研究。在摇瓶发酵时,最佳种龄为16h,接种量为3％,甲醇的诱导浓度为15g／L,生长阶段最适pH为5．0,诱导阶段最适pH为5．5。在间歇补料、恒速补料、变速补料三种补料方式中以变速流加最优。     

乳糖诱导重组尿酸酶基因在大肠杆菌中的表达

对用乳糖替代异丙基-β-D-硫代半乳糖苷(IPTG)诱导重组产朊假丝酵母尿酸酶基因在E.coli JM109(DE3)中表达进行了研究,拟建立一种高效低成本的生产重组尿酸酶的工艺路线。通过摇瓶试验对诱导所采用的乳糖浓度,诱导时机和诱导持续时间进行了优化,并考察在乳糖诱导下的目的产物表达动力学,随后在5 L发酵罐上进行扩大化培养以验证摇瓶优化的结果,进一步将乳糖作为诱导剂应用于高密度发酵过程。实验结果表明乳糖诱导的最佳浓度为5 g/L,最佳诱导时机是对数生长期中后期,诱导持续时间为9~10h;按照优化的条件在摇瓶和5 L发酵罐上进行分批培养,重组尿酸酶最大表达量可达菌体总蛋白的26%左右,可溶性蛋白的36%左右,略高于IPTG的诱导效果;高密度发酵过程菌体终密度达到OD600值40以上,尿酸酶表达量占菌体总蛋白25%左右。     

毕赤酵母高密度表达重组猪胰岛素前体的研究

对摇瓶和50L罐上的重组菌毕赤酵母(Pichia pastoris)表达猪胰岛素前体(PIP)的发酵过程进行了研究。摇瓶发酵中,最佳诱导周期为60 h左右,诱导期甲醇的最佳加入量为每日2．0%～2．5%。50L发酵过程分为批发酵、补料和诱导表达3个阶段。生长期(批发酵和补料阶段)细胞干重与培养时间的关系可用模型y= 0．6525e~(0．1909t)来描述。在批发酵阶段和补料阶段,流加的氨水和甘油几乎全部用来合成菌体和维持,没有其他副产物产生。诱导表达阶段流加的氨水和甲醇分别约有80%和70%被菌体利用。将摇瓶与发酵罐的实验结果进行了比较,发现摇瓶发酵的限制因子很可能是溶氧,而罐发酵的限制因子为碳源,因此,将摇瓶实验的结果放大到发酵罐时调整了控制策略,加大了甲醇的补料速率,最终PIP浓度达到1．72g/L。     

重组毕赤酵母生产β-葡萄糖苷酶发酵条件初步研究

为提高重组毕赤酵母(P.pastoris KM71/pPIC9K-bgl)生产β-葡萄糖苷酶的产量,在摇瓶条件下对重组P.pastoris产β-葡萄糖苷酶的发酵过程进行了优化,得到最佳的条件:生长阶段甘油浓度为30 g/L,接种量为10%,诱导阶段甲醇的初浓度为4%,过程补加甲醇0.5%,诱导温度30℃,pH7.5,诱导周期120 h,酶活可达到245 U/mL。在此基础上,在3 L发酵罐上进行初步放大,流加甘油提高细胞密度至OD_(600)为170,开始流加甲醇诱导,最终BGL酶活达到1 175 U/mL。比摇瓶提高了4.8倍,为β-葡萄糖苷酶工业化生产打下了坚实的基础。     

表达酿酒酵母ALAS的重组大肠杆菌胞外5-氨基乙酰丙酸的产量和纯化

5-氨基乙酰丙酸（5-aminolevulinate,ALA）由5-氨基乙酰丙酸合酶（5-aminolevulinate synthase,ALAS）催化产生。利用重组细菌在大肠杆菌合成ALA已有不少研究。重组真核生物ALAS在大肠杆菌合成ALA的研究没有报道。酿酒酵母ALAS在大肠杆菌重组表达,在摇瓶培养条件下,分析了胞外ALA的产量,重组菌的生长状况和细胞中ALAS的活性,利用两种国产树脂纯化ALA,毛细管电泳分析确定ALA纯度在LB培养基中,初始pH 6.5,含有20mmol/L的酮戊酸、20mmol/L琥珀酸和20mmol/L的甘氨酸,37℃下诱导培养12h,胞外ALA的产量为162mg /L培养基。纯化的ALA纯度达到90%。     

表达酿酒酵母ALAS的重组大肠杆菌胞外5-氨基乙酰丙酸的产量和纯化

5-氨基乙酰丙酸(5-aminolevulinate,ALA)由5-氨基乙酰丙酸合酶(5-aminolevulinate synthase,ALAS)催化产生。利用重组细菌在大肠杆菌合成ALA已有不少研究。重组真核生物ALAS在大肠杆菌合成ALA的研究没有报道。酿酒酵母ALAS在大肠杆菌重组表达,在摇瓶培养条件下,分析了胞外ALA的产量,重组菌的生长状况和细胞中ALAS的活性,利用两种国产树脂纯化ALA,毛细管电泳分析确定ALA纯度在LB培养基中,初始pH6.5,含有20mmol/L的酮戊酸、20mmol/L琥珀酸和20mmol/L的甘氨酸,37℃下诱导培养12h,胞外ALA的产量为162mg/L培养基。纯化的ALA纯度达到90%。     

表达重组葡激酶-水蛭素融合蛋白的大肠杆菌工程菌的高密度培养

采用溶氧反馈的分批培养流加补料的方法高密度培养重组大肠杆菌BL21(DE3)生产重组葡激酶-水蛭素融合蛋白。通过摇瓶培养对菌种和培养条件的初步筛选,采用溶氧反馈的流加补料策略,进行了5L发酵罐的合成培养基和复合培养基的发酵工艺的研究。通过对培养条件的不断优化,重组葡激酶-水蛭素融合蛋白在大肠杆菌BL21(DE3)里得到了高效表达,菌体密度最终达到115g/L(WCW)以上,可溶性重组融合蛋白占菌体总蛋白的30%以上,含量约为1.1~1.2g/L。5L发酵罐的发酵工艺参数在40L发酵罐中进行了放大培养,结果表明该工艺能有效的放大,可适用于工业生产。     

一株法夫酵母虾青素高产菌株的生产性能

为了评价虾青素高产菌株-法夫酵母JMU-MVP14的生产性能及建立虾青素高产发酵技术,通过测定糖、生物量、虾青素产量、总类胡萝卜素产量等发酵参数,用摇瓶试验对比了法夫酵母JMU-MVP14和出发菌株的差异,用7 L罐试验对比了pH值调控方式及补料培养基成分对发酵的影响,用1 m3罐试验评估了法夫酵母JMU-MVP14高密度发酵虾青素的产量水平。摇瓶发酵结果表明,法夫酵母JMU-MVP14虾青素及总类胡萝卜素的细胞产率分别达到6.01 mg/g及10.38 mg/g;7 L罐分批发酵试验结果表明,自动流加调     

Effect of inducers on the production of 5-aminolevulinic acid by recombinant Escherichia coli

Aminolevulinic acid (ALA) was produced by recombinant Escherichia coli BL21(DE3) (pET28-A.R-hemA) harboring the ALA synthase gene (hemA) from Agrobacterium radiobacter zju-0121. The effects of inducers on the ALA synthase activity and ALA productivity were evaluated. The results indicated that a low isopropyl-beta-D-thiogalactoside (IPTG) concentration (0.05 mmol/L) was favorable for high expression of ALA synthase, which resulted in higher ALA productivity. For metabolic engineering applications, lactose was a better substitute of IPTG for active enzyme expression. When lactose concentration was 5 mmol/L, the specific ALA synthase activity and ALA productivity reached 16.7 nmol/(min . mg of protein) and 1.15 g/L, respectively, which were about 15% and 43% higher than those induced by IPTG.     

流加发酵对重组Bacillus subtilis发酵生产角质酶的影响

为实现基因工程菌Bacillus subtilis WSHB06-07生产角质酶的高产,在3L发酵罐中考察了不同初糖浓度对菌体生长和产酶的影响,并在选择38 g/L初始蔗糖浓度的基础上,进行碳源的分批流加和恒速流加,结果表明发酵16 h开始流加碳源,采用总补糖量60g/L,蔗糖平均流速为4g/(L·h)的恒速补料方式,角质酶酶活在31h可达到最大545.87U/ml,比分批发酵酶活提高67.8%,并获得较高的角质酶生产强度,满足工业化生产要求。     

重组戊型肝炎病毒衣壳蛋白工程菌的高密度培养

在10L发酵罐中对戊型肝炎病毒衣壳蛋白在重组大肠杆菌中表达发酵工艺进行了研究,用分批培养方法探讨了不同培养基、培养基中磷酸盐浓度和Mg^2＋浓度等因素对菌体生长与重组蛋白表达的影响;用分批补料培养研究了不同的补料工艺对菌体生长与重组蛋白表达的影响,同时对重组菌诱导时期、诱导持续时间以及不同诱导温度表达包含体在尿素溶液中的溶解性进行了研究。结果表明,在优化后的培养基中,磷酸盐浓度、Mg^2＋浓度分别为80mmol/L 与20mmol/L时菌体生长与表达效果较好;分批补料培养中,37℃培养9h菌体达到对数期中期(约45OD600)为适宜诱导时期,加入终浓度为10mmol/L IPTG后诱导5h,OD600达到80以上,重组蛋白表达量达到29.74％,为最适收获菌体时间;37℃表达的包含体80％以上溶解在4mol/L的尿素溶液中,最终浓度达到14mg/mL; 10L发酵罐中确定的发酵工艺参数在30L发酵罐中进行了放大培养,10L发酵罐中确定的发酵工艺参数在30L发酵罐上具有可放大性与重复性, 可以应用于工业生产。     

Enhanced acetone-butanol fermentation using repeated fed-batch operation coupled with cell recycle by membrane and simultaneous removal of inhibitory products by adsorption

A novel acetone-butanol production process was developed which integrates a repeated fed-batch fermentation with continuous product removal and cell recycle. The inhibitory product concentrations of the fermentation by Clostridium acetobutylicum were reduced by the simultaneous extraction process using polyvinylpyridine (PVP) as an adsorbent. Because of the reduced inhibition effect, a higher specific cell growth rate and thus a higher product formation rate was achieved. The cell recycle using membrane separation increased the total cell mass density and, therefore, enhanced the reactor productivity. The repeated fed-batchoperation overcame the drawbacks typically associated with a batch operation such as down times, long lag period, and the limitation on the maximum initial substrate concentration allowed due to the substrate inhibition. Unlike a continuous operation, the repeated fed-batch operation could beoperated for a long time at a relatively higher substrate concentration without sacrificing the substrate loss in the effluent. As a result, the integrated process reached 47.2 g/L in the equivalent solvent concentration (including acetone, butanol, and ethanol) and 1.69 g/L . h in the fermentor productivity, on average, over a 239.5-h period. Compared with a controlled traditional batch acetone-butanol fermentation, the equivalent solvent concentration and the tormentor productivity were increased by 140% and 320%, respectively. (c) 1995 John Wiley & Sons Inc.     

Enhancement of 5-aminolevulinate production with recombinant Escherichia coli using batch and fed-batch culture system

5-Aminolevulinate (ALA) production with recombinant Escherichia coli Rosetta (DE3)/pET28a(+)-hemA was studied. In batch fermentation, the addition of glucose and glycine was effective to improve ALA production. Then the fed-batch fermentation was conducted with continuous feeding of precursors. When the concentrations of succinic acid and glycine were 7.0 g/l and 4.0 g/l, respectively, in the feeding, the ALA yield reached 4.1g/l. But the molar yield (ALA/glycine) was decreased in the fed-batch fermentation compared to batch fermentation. And it was found that the pH control during fed-batch cultivation was very important for the cell growth and ALA production. A two-stage pH value controlling strategy was suggested, in which, the pH value in the first 6h was regulated at pH 5.9, after then at pH 6.2, and the ALA yield was as high as 6.6g/l via fed-batch fermentation.     

Citric acid production by Candida lipolytica Y 1095 in cell recycle and fed-batch fermentors

The effect of dissolved oxygen on citric acid production and oxygen uptake by Candida lipolytica Y 1095 was evaluated in cell recycle and fed-batch fermentation systems. The maximum observed volumetric productivity, which occurred at a dilution rate of 0.06 h(-1), a dissolved oxygen concentration of 80%, and a biomass concentration of 5% w/v, in the cell recycle system, was 1.32 g citric acid/L . h. At these same conditions, the citric acid yield was 0.65 g/g and the specific citric acid productivity was 24.9 mg citric acid/g cell . h. In the cell recycle system, citric acid yields ranged from 0.45 to 0.72 g/g. Both the volumetric and specific citric acid productivities were dependent on the dilution rate and the concentration of dissolved oxygen in the fermentor. Similar productivities (1.29 g citric acid/L . h) were obtained in the fed-batch system operated at a cycle time of 36 h, a dissolved oxygen concentration of 80%, and 60 g total biomass. Citric acid yields in the fed-batch fermentor were consistently lower than those obtained in the cell recycle system and ranged from 0.40 to 0.59 g/g. Although citric acid yields in the fed-batch fermentor were lower than those obtained in the cell recycle system, higher citric:isocitric acid ratios were obtained in the fed-batch fermentor. As in the cell recycle system, both the volumetric and specific citric acid productivities in the fed-batch fermentor were dependent on the cycle time and dissolved oxygen concentration. (c) 1995 John Wiley & Sons, Inc.     

鸟苷补料分批发酵的研究

目的:以枯草芽孢杆菌TA208为出发菌株,研究了补料分批发酵方式下各种参数对鸟苷产量的影响。方法:采用补料分批发酵工艺,利用纸层析法测定发酵液中鸟苷的产量。结果:确定了葡萄糖、酵母粉和次黄嘌呤的最优补料方式,使鸟苷产量达到32.05g/L,较分批发酵方式提高了36.3%。结论:发酵工艺过程控制对发酵生产鸟苷具有重大影响。     

表达血管生长抑制素的重组毕赤酵母在诱导阶段混合碳源的流加

为进行高密度发酵并实现外源基因的高表达,在表型为Mut^S的重组毕赤酵母（Pichia pastoris）表达人血管生长抑制素的诱导阶段,采用了甘油甲醇混合补料的培养方式。以溶氧水平作为甘油代谢指针来控制甘油限制性流加既可维持一定菌体生长,又不会发生发酵液中残余甘油及有害代谢产物（乙醇）阻遏蛋白表达。当表达阶段的菌体平均比生长速率控制于0.012h^-1,菌体浓度达150 g/L,血管生长抑制素浓度最高达到108 mg/L,血管生长抑制素的平均比生产速率为0.02 mg/(g·h),菌体关于甘油的表观得率为0.69 g/g,菌体关于甲醇的表观得率为0.93g/g,较没有采用甘油限制性流加时都有所提高。     

Batch and fed-batch cultivation for excretive production of human epidermal growth factor (hEGF) with recombinant E. Coli K12 system

Batch and fed-batch production of recombinant human epidermal growth factor (hEGF) was studied in an E. coli secretary expression system. By using MMBL medium containing 5 g/L glucose, controlling the temperature at 32 degrees C and maintaining the dissolved oxgen level over 20% saturation, a high yield of hEGF (32 mg/L) was obtained after an 18 hr batch cultivation with 0.2 mM IPTG induction at mid-log phase. Three different glucose feeding strategies were employed to further improve hEGF productivity in a bench top fermentor. Compared with the batch results, hEGF yield was improved up to 25.5% or 28.1%, respectively by intermittent or pH-stat glucose feeding, and up to 150% improvement of hEGF production was achieved by constant feeding of 200 g/L glucose solution at a rate of 0.11 mL/min. The effects of further combined feeding with other medium components and inducer on hEGF yield were also examined in the benchtop fermentor. This work is very helpful to further improve the productivity of extracellular hEGF in the recombinant E. coli system.