Construction of viscoelastic biocompatible films via the layer-by-layer assembly of hyaluronan and phosphorylcholine-modified chitosan

Films of hyaluronan (HA) and a phosphorylcholine-modified chitosan (PC-CH) were constructed by the polyelectrolyte multilayer (PEM) deposition technique and their buildup in 0.15 M NaCl was followed by atomic force microscopy, surface plasmon resonance spectroscopy (SPR), and dissipative quartz crystal microbalance (QCM). The HA/PC-CH films were stable over a wide pH range (3.0-12.0), exhibiting a stronger resistance against alkaline conditions as compared to HA/CH films. The loss and storage moduli, G' and G", of the films throughout the growth of eight bilayer assemblies were derived from an impedance analysis of the QCM data recorded in situ. Both G' and G" values were one order of magnitude lower than the moduli of HA/CH films. The fluid gel-like characteristics of HA/PC-CH multilayers were attributed to their high water content (50 wt %), which was estimated by comparing the surface coverage values derived from SPR and QCM measurements. Given the versatility of the PEM methodology, HA/PC-CH films are attractive tools for developing biocompatible surface coatings of controlled mechanical properties.     

Dynamic adsorption behavior of poly(3-hydroxybutyrate) depolymerase onto polyester surface investigated by QCM and AFM

Time-dependent adsorption behavior of poly(3-hydroxybutyrate) (PHB) depolymerase from Ralstonia pickettiiT1 on a polyester surface was studied by complementary techniques of quarts crystal microbalance (QCM) and atomic force microscopy (AFM). Amorphous poly(l-lactide) (PLLA) thin films were used as adsorption substrates. Effects of enzyme concentration on adsorption onto the PLLA surface were determined time-dependently by QCM. Adsorption of PHB depolymerase took place immediately after replacement of the buffer solutions with the enzyme solutions in the cell, followed by a gradual increase in the amount over 30 min. The amount of PHB depolymerase molecules adsorbed on the surface of amorphous PLLA thin films increased with an increase in the enzyme concentration. Time-dependent AFM observation of enzyme molecules was performed during the adsorption of PHB depolymerase. The phase response of the AFM signal revealed that the nature of the PLLA surface around the PHB depolymerase molecule was changed due to the adsorption function of the enzyme and that PHB depolymerase adsorbed onto the PLLA surface as a monolayer at a lower enzyme concentration. The number of PHB depolymerase molecules on the PLLA surface depended on the enzyme concentration and adsorption time. In addition, the height of the adsorbed enzyme was found to increase with time when the PLLA surface was crowded with the enzymes. In the case of higher enzyme concentrations, multilayered PHB depolymerases were observed on the PLLA thin film. These QCM and AFM results indicate that two-step adsorption of PHB depolymerase occurs on the amorphous PLLA thin film. First, adsorption of PHB depolymerase molecules takes place through the characteristic interaction between the binding domain of PHB depolymerase and the free surface of an amorphous PLLA thin film. As the adsorption proceeded, the surface region of the thin film was almost covered with the enzyme, which was accompanied by morphological changes. Second, the hydrophobic interactions among the enzymes in the adlayer and the solution become more dominant to stack as a second layer.     

Quartz crystal microbalance: a useful tool for studying thin polymer films and complex biomolecular systems at the solution-surface interface

The quartz crystal microbalance (QCM) is a simple, cost effective, high-resolution mass sensing technique, based upon the piezoelectric effect. As a methodology, the QCM evolved a solution measurement capability in largely analytical chemistry and electrochemistry applications due to its sensitive solution-surface interface measurement capability. The technique possesses a wide detection range. At the low mass end, it can detect monolayer surface coverage by small molecules or polymer films. At the upper end, it is capable of detecting much larger masses bound to the surface. These can be complex arrays of biopolymers and biomacromolecules, even whole cells. In addition, the QCM can provide information about the energy dissipating properties of the bound surface mass. Another important and unique feature of the technique is the ability to measure mass and energy dissipation properties of films while simultaneously carrying out electrochemistry on solution species or upon film systems bound to the upper electrode on the oscillating quartz crystal surface. These measurements can describe the course of electropolymerization of a film or can reveal ion or solute transport within a film during changes in the film environment or state, including the oxidation state for an electroactive film driven by the underlying surface potential. The past decade has witnessed an explosive growth in the application of the QCM technique to the study of a wide range of molecular systems at the solution-surface interface, in particular, biopolymer and biochemical systems. In this report, we start with a brief historical and technical overview. Then we discuss the application of the QCM technique to measurements involving micellar systems, self-assembling monolayers and their phase transition behavior, molecularly imprinted polymers, chemical sensors, films formed using the layer-by-layer assembly technique, and biopolymer films and point out the utility of the electrochemical capabilities of the technique to characterizing film properties, especially electroactive polymer films. We also describe the wide range of surface chemistries and attachment strategies used by investigators to bring about surface attachment and multi-layer interactions of these thin film systems. Next we review the wide range of recent applications of the technique to: studies of complex biochemical and biomimetic systems, the creation of protein and nucleic acid biosensors, studies of attached living cells and whole cell biosensor applications. Finally, we discuss future technical directions and applications of the QCM technique to areas such as drug discovery.     

Model films from native cellulose nanofibrils. Preparation, swelling, and surface interactions

Native cellulose model films containing both amorphous and crystalline cellulose I regions were prepared by spin-coating aqueous cellulose nanofibril dispersions onto silica substrates. Nanofibrils from wood pulp with low and high charge density were used to prepare the model films. Because the low charged nanofibrils did not fully cover the silica substrates, an anchoring substance was selected to improve the coverage. The model surfaces were characterized using atomic force microscopy (AFM) and X-ray photoelectron spectroscopy (XPS). The effect of nanofibril charge density, electrolyte concentration, and pH on swelling and surface interactions of the model film was studied by quartz crystal microbalance with dissipation (QCM-D) and AFM force measurements. The results showed that the best coverage for the low charged fibrils was achieved by using 3-aminopropyltrimethoxysilane (APTS) as an anchoring substance and hence it was chosen as the anchor. The AFM and XPS measurements showed that the fibrils are covering the substrates. Charge density of the fibrils affected the morphology of the model surfaces. The low charged fibrils formed a network structure while the highly charged fibrils formed denser film structure. The average thickness of the films corresponded to a monolayer of fibrils, and the average rms roughness of the films was 4 and 2 nm for the low and high charged nanofibril films, respectively. The model surfaces were stable in QCM-D swelling experiments, and the behavior of the nanofibril surfaces at different electrolyte concentrations and pHs correlated with other studies and the theories of Donnan. The AFM force measurements with the model surfaces showed well reproducible results, and the swelling results correlated with the swelling observed by QCM-D. Both steric and electrostatic forces were observed and the influence of steric forces increased as the films were swelling due to changes in pH and electrolyte concentration. These films differ from previous model cellulose films due to their chemical composition (crystalline cellulose I and amorphous regions) and fibrillar structure and hence serve as excellent models for the pulp fiber surface.     

Bioadhesion of supramolecular structures at supported planar bilayers as studied by the quartz crystal microbalance

A quartz crystal microbalance (QCM) was used to study the adhesion behavior of supramolecular aggregates at supported planar bilayers (SPBs). The QCM technique is a suitable method to detect the adsorption of biomolecules at the quartz surface owing to its sensitivity for changes in mass and viscoelastic properties. To simulate biomembranes, the quartz plates were coated with highly ordered lipid films. Therefore, a combination of self-assembled monolayers and Langmuir-Blodgett films was used. Firstly, the adsorption of liposomes coupled with the lectin concanavalin A was investigated at glycolipid-containing model membranes. Using different carbohydrates, it was possible to determine specific and nonspecific parts of the interactions. The adhesion occurred owing to specific lectin-carbohydrate interactions (about 20%) and to nonspecific interactions (about 80%). The composition of the liposomes was changed to simulate the structure of a native biomembrane consisting of the glycocalix, the lipid-protein bilayer, and the cytoskeleton. An artificial glycocalix was created by incorporating poly(ethylene glycol) into the liposomes. Liposomes which were intravesicular polymerized with polyacrylamide or polyacrylcholate simulated the cytoskeleton. It was determined that the modified liposomes had significant lower interactions with SPBs. The adsorption was reduced by approximately 80% compared to unmodified liposomes. Secondly, a model was developed for the detection of interactions between simple or mixed bile salt micelles and model membranes. It was found that simple bile salts did not adsorb at model membranes. Binary systems consisting of bile salt and phospholipid induced only small interactions. On the other hand, ternary systems consisting of bile salt, phospholipid, and fatty acid showed strong interactions. A dependence on the chain length of the fatty acid was observed. Thirdly, the interaction between ganglioside-containing model membranes and cholera toxin (beta-subunit) was investigated. Different ganglioside fractions showed varying adsorption in the following sequence: GM1 > GD1a > GD1b > GT1b.     

Bifunctional dendronized cellulose surfaces as biosensors

Well-defined dendronized cellulose substrates displaying multiple representations of dual-functionality were constructed by taking advantage of the efficiency of the click reaction combined with traditional anhydride chemistry. First, activated cellulose surfaces were decorated with several generations of dendrons, and their peripheral reactive groups were subsequently reacted with a trifunctional orthogonal monomer. The generated substrate tool box was successfully explored by accurately tuning the surface function using a versatile orthogonal dual postfunctionalization approach. In general, the reactions were monitored by using a click-dye reagent or a quartz crystal microbalance (QCM) technique, and the resulting surfaces were well-characterized using XPS, FT-IR, and contact angle measurements. Utilizing this approach two different surfaces have been obtained; that is, triethylenglycol oligomers and amoxicillin molecules were efficiently introduced to the dendritic surface. As a second example, mannose-decorated hydroxyl functional surfaces illustrated their potential as biosensors by multivalent detection of lectin protein at concentration as low as 5 nM.     

Adsorption and hydrolysis reactions of poly(hydroxybutyric acid) depolymerases secreted from Ralstonia pickettii T1 and Penicillium funiculosum onto poly[(R)-3-hydroxybutyric acid

Reaction processes of poly[(R)-3-hydroxybutyric acid] (P(3HB)) with two types of poly(hydroxybutyric acid) (PHB) depolymerases secreted from Ralstonia pickettii T1 and Penicillium funiculosum were characterized by means of atomic force microscopy (AFM) and quartz crystal microbalance (QCM). The PHB depolymerase from R. pickettii T1 consists of catalytic, linker, and substrate-binding domains, whereas the one from P. funiculosum lacks a substrate-binding domain. We succeeded in observing the adsorption of single molecules of the PHB depolymerase from R. pickettii T1 onto P(3HB) single crystals and the degradation of the single crystals in a phosphate buffer solution at 37 degrees C by real-time AFM. On the contrary, the enzyme molecule from P. funiculosum was hardly observed at the surface of P(3HB) single crystals by real-time AFM, even though the enzymatic degradation of the single crystals was surely progressed. On the basis of the AFM observations in air of the P(3HB) single crystals after the enzymatic treatments, however, not only the PHB depolymerase from R. pickettii T1 but also that from P. funiculosum adsorbed onto the surface of P(3HB) crystals, and both concentrations of the enzymes on the surface were nearly identical. This means both enzymes were adsorbed onto the surface of P(3HB) single crystals. Moreover, QCM measurements clarified quantitatively the differences in detachment behavior between two types of PHB depolymerases, namely the enzyme from R. pickettii T1 was hardly detached but the enzyme from P. funiculosum was released easily from the surface of P(3HB) crystals under an aqueous condition.     

Investigation of the orientation of purple membrane sheets in Langmuir-Blodgett films by a quartz crystal microbalance

By means of the quartz crystal microbalance (QCM), a convenient method was developed to determine the degree of orientation of purple membrane (PM) sheets on the air/water interface. Langmuir-Blodgett films from both wild-type and SH-mutant PM (bR D36C) were vertically deposited on the surface of gold-sputtered AT-cut quartz crystals. The shift of resonance frequency of the QCM during a special washing protocol allowed us to differentiate between physically adsorbed PM fragments and any PM attached to the gold surface via chemical bonds. By washing with organic solvents, complete desorption of the wild-type PM was achieved, whereas for the SH-mutant, approximately 60% of the PM fragments could not be detached from the surface. These PM sheets should be oriented with the cytoplasmic side facing the water subphase to that their SH-groups can chemically bind to the gold surface of the quartz plate.     

Characterization of QCM sensor surfaces coated with molecularly imprinted nanoparticles

Molecularly imprinted polymers (MIPs) are gaining great interest as tailor-made recognition materials for the development of biomimetic sensors. Various approaches have been adopted to interface MIPs with different transducers, including the use of pre-made imprinted particles and the in situ preparation of thin polymer layers directly on transducer surfaces. In this work we functionalized quartz crystal microbalance (QCM) sensor crystals by coating the sensing surfaces with pre-made molecularly imprinted nanoparticles. The nanoparticles were immobilized on the QCM transducers by physical entrapment in a thin poly(ethylene terephthalate) (PET) layer that was spin-coated on the transducer surface. By controlling the deposition conditions, it was possible to gain a high nanoparticle loading in a stable PET layer, allowing the recognition sites in nanoparticles to be easily accessed by the test analytes. In this work, different sensor surfaces were studied by micro-profilometry and atomic force microscopy and the functionality was evaluated using quartz crystal microbalance with dissipation (QCM-D). The molecular recognition capability of the sensors were also confirmed using radioligand binding analysis by testing their response to the presence of the test compounds, (R)- and (S)-propranolol in aqueous buffer.     

The quartz crystal microbalance as a continuous monitoring tool for the study of endothelial cell surface attachment and growth

The quartz crystal microbalance (QCM) was used to monitor endothelial cell (EC) adhesion on the gold surface of an oscillating quartz crystal contained in a QCM device. A number of parameters were investigated. First, we observed differential QCM O-ring toxicities for ECs. Second, appropriate conditions for cell culture and QCM cell environment were identified that can eliminate large-scale frequency oscillations in the measurements. These artifacts are not due to added cells but originate in the time-dependent evaporation of water. Having eliminated these artifacts, we then demonstrated that the measured steady-state crystal frequency shift, Delta f, and motional resistance shift, DeltaR, were determined by the number of firmly attached ECs requiring trypsinization from the crystal surface. Last, following steady-state attachment of ECs, the EC growth stimulation by fibroblast growth factor was monitored in a continuous fashion by measuring f and R values over a 72 h. period. We observed the Delta f values to increase in a way that reflected the increase in EC number bound to the QCM surface. Following addition of ECs to the QCM, the time-dependent increase in DeltaR can be interpreted in terms of increase by the ECs of the energy dissipation properties of the solution at the solution-gold surface interface. This effect is due to their rapid surface attachment and the elaboration of their cytoskeletal properties. These results indicate that the QCM technique can be used for the study of EC attachment and growth and suggest its potential for the real time study of per unit surface area cell mass distribution dynamics and viscoelastic properties and the cells' responses to stresses or perturbations brought about using biologically active molecules.     

Immobilization of galactose ligands on acrylic acid graft-copolymerized poly(ethylene terephthalate) film and its application to hepatocyte culture

Surface modification of argon-plasma-pretreated poly(ethylene terephthalate) (PET) films via UV-induced graft copolymerization with acrylic acid (AAc) was carried out. Galactosylated surfaces were then obtained by coupling a galactose derivative (1-O-(6'-aminohexyl)-D-galactopyranoside) to the AAc graft chains with the aid of a water-soluble carbodiimide (WSC) and N-hydroxysulfosuccinimide (sulfo-NHS). The modified PET films were characterized by X-ray photoelectron spectroscopy (XPS), atomic force microscopy (AFM), and water contact-angle measurements. The galactosylated PET films were used as substrates for hepatocyte culture. The effects of surface carboxyl group concentration on the extent of galactose ligand immobilization, the extent of hepatocyte attachment, and the surface morphology were investigated. The amount of the galactose ligands immobilized on the PET surface increased with the AAc polymer graft concentration. AFM images revealed that the surface roughness of the PET film increased after graft copolymerization with AAc, but did not change appreciably with the subsequent immobilization of the galactose ligands. At the surface carboxyl group concentration of about 0.56 micromol/cm(2) or galactose ligand concentration of about 0.51 micromol/cm(2), the hepatocyte culture on the galactosylated surface exhibited the optimum concentration and physiological functions and formed aggregates or spheroids after just 1 day of culture. The albumin and urea synthesis functions of these hepatocytes were comparable to or higher than those of the hepatocytes cultured on the collagen-modified PET substrates.     

Influence of cosolvents on the hydrophobic surface immobilization topography of Candida antarctica lipase B

The presence of cosolvents and co-solutes during the immobilization of lipases on hydrophobic supports may influence the extent of lipase immobilization and the long-term catalytic stability of the biocatalyst. Candida antarctica B lipase immobilization was examined on a hydrophobic surface, i.e., gold modified with a methyl-terminated, self-assembled alkylthiol layer. Lipase adsorption was monitored gravimetrically using a quartz crystal microbalance (QCM). Lipase activity was determined colorimetrically by following p-nitrophenol propionate hydrolysis. Adsorbed lipase topography was examined by atomic force microscopy (AFM). Lipase adsorption from low ionic strength aqueous buffer produced a uniform confluent protein monolayer. Inclusion of 10% (vol) ethanol in the buffer during immobilization resulted in a 33% adsorbed mass increase. Chemically similar cosolvents, all at 10% by volume in buffer, were also individually examined for their influence on CALB adsorption. Glycerol or 1-propanol increased mass adsorption by 10%, while 2-propanol increased mass adsorption by 33%. QCM dissipation values increased threefold with the inclusion of either ethanol or 2-propanol in the medium during lipase adsorption, indicating formation of multilayers of CALB. Partial multilayer formation using 10% ethanol was confirmed by AFM. Inclusion of 10% ethanol in the CALB immobilization buffer decreased the specific activity of the immobilized lipase by 37%. The formation of lipase multilayers in the presence of certain cosolvents thus results in lower specific activity, which might be due to either influences on lipase conformation or substrate active site accessibility.     

Surface modification of chitosan films. Effects of hydrophobicity on protein adsorption

The surface of chitosan films was modified using acid chloride and acid anhydrides. Chemical composition at the film surface was analyzed by attenuated total reflectance Fourier-transform infrared spectroscopy (ATR-FTIR) and X-ray photoelectron spectroscopy (XPS). ATR-FTIR data verified that the substitution took place at the amino groups of chitosan, thus forming amide linkages, and the modification proceeded to the depth at least 1 microm. Choices of molecules substituted at the amino groups of the glucosamine units did affect the hydrophobicity of the film surface, as indicated by air-water contact angle analysis. The surface became more hydrophobic than that of non-modified film when a stearoyl group (C(17)H(35)CO-) was attached to the films. The reaction of chitosan films with succinic anhydride or phthalic anhydride, however, produced more hydrophilic films. Selected modified films were subjected to protein adsorption study. The amount of protein adsorbed, determined by bicinchoninic acid (BCA) assay, related to the types of attached molecules. The improved surface hydrophobicity affected by the stearoyl groups promoted protein adsorption. In contrast, selective adsorption behavior was observed in the case of the chitosan films modified with anhydride derivatives. Lysozyme adsorption was enhanced by H-bonding and charge attraction with the hydrophilic surface. While the amount of albumin adsorbed was decreased possibly due to negative charges that gave rise to repulsion between the modified surface and albumin. This study has demonstrated that it is conceivable to fine-tune surface properties which influence its response to bio-macromolecules by heterogeneous chemical modification.     

A blank slate? Layer-by-layer deposition of hyaluronic acid and chitosan onto various surfaces

Although poly(alpha-hydroxy esters), especially the PLGA family of lactic acid/glycolic acid copolymers, have many properties which make them promising materials for tissue engineering, the inherent chemistry of surfaces made from these particular polymers is problematic. In vivo, they promote a strong foreign-body response as a result of nonspecific adsorption and denaturation of serum proteins, which generally results in the formation of a nonfunctional fibrous capsule. Surface modification post-production of the scaffolds is an often-utilized approach to solving this problem, conceptually allowing the formation of a scaffold with mechanical properties defined by the bulk material and molecular-level interactions defined by the modified surface properties. A promising concept is the so-called "blank slate": essentially a surface that is rendered resistant to nonspecific protein adsorption but can be readily activated to covalently bind bio-functional molecules such as extracellular matrix proteins, growth factors or polysaccharides. This study focuses on the use of the quartz crystal microbalance (QCM) to follow the layer-by-layer (LbL) electrostatic deposition of high molecular weight hyaluronic acid and chitosan onto PLGA surfaces rendered positively charged by aminolysis, to form a robust, protein-resistant coating. We further show that this surface may be further functionalized via the covalent attachment of collagen IV, which may then be used as a template for the self-assembly of basement membrane components from dilute Matrigel. The response of NIH-3T3 fibroblasts to these surfaces was also followed and shown to closely parallel the results observed in the QCM.     

Hydration-dehydration of adsorbed protein films studied by AFM and QCM-D

The hydration-dehydration process of an adsorbed human serum albumin film has been studied using atomic force microscopy (AFM) and a quartz crystal microbalance (QCM). All measurements were performed with identically prepared protein films deposited on highly hydrophilic substrates. Both techniques are shown to be suitable for following in situ the kinetics of protein hydration, and for providing quantitative values of the adsorbed adlayer mass. The results obtained by the two methods have been compared and combined to study changes of physical properties of the films in terms of viscosity, shear, Young's modulus, density and film thickness. These properties were found to be reversible during hydration-dehydration cycles.     

Chemisorption of proteins and their thiol derivatives onto gold surfaces: characterization based on electrochemical nonlinearity

This study was conducted to monitor the electrochemical responses of two proteins (bovine serum albumin (BSA) and gelatin) and their thiol derivatives adsorbed onto gold (Au) electrodes, which were analyzed by a "nonlinear" impedance method. A sinusoidal voltage is applied to a protein-containing aqueous solution and the waveform of the output current is analyzed by fast Fourier transformation (FFT). The intensities of the higher harmonics in the FFT varied with the species of protein and their thiol derivatives, and with time. From the higher harmonics, voltage-dependent capacitance and conductance were quantitatively evaluated to differentiate the state of adsorbed protein. Adsorption and desorption characteristics of BSA and its thiol derivative on the Au surface were continuously measured by a quartz crystal microbalance (QCM) in situ. The microscopic state of thiol-derivatized BSA adsorbed onto the Au surface was imaged by atomic force microscopy (AFM). In general, thiol-derivatized proteins were tightly adsorbed on the Au surface and showed no desorption. The present electrochemical measurements clearly differentiated adsorption characteristics of physically adsorbed (physisorbed) and chemically adsorbed (chemisorbed) proteins on Au surfaces.     

Simultaneous monitoring of electroformation of phospholipid vesicles by quartz crystal microbalance and optical microscopy

The electroformation of giant vesicles from 1,2-Dimyristoyl-sn-Glycero-3-Phosphocholine (DMPC) was monitored using quartz crystal microbalance with dissipation monitoring (QCM-D) and optical microscopy, simultaneously using a novel sample cell design. A gold-coated QCM crystal was used as one of the electrodes and an Indium–tin-oxide (ITO)-coated glass slide was used as the second electrode for electroformation. Increases in the frequency and decreases in the dissipation were observed immediately upon voltage application between the two electrodes, indicating the loss of lipid from the QCM surface. Concurrently, we observed vesicles on the QCM electrode surface by differential interference contrast (DIC)-optical microscopy. The lipid-coated substrates were measured with AFM at various stages in the electroformation, and a significant change in the morphology of the lipid film was observed. Ellipsometry was used to find the average thickness of lipid film. The QCM data were fitted to a viscoelastic model to determine the viscoelastic properties and time dependence of the film thickness. All methods used to determine film thickness give values in reasonable quantitative agreement. Differences between the methods are consistent with what one might expect due to what is actually measured in the individual techniques. The comparison between mass loss and observed vesicles suggest that the vesicles formed are first localized to the substrate and then slowly released into the solution. By comparing the mass lost from the lipid film, to the total surface area of lipid vesicles observed, it is apparent that only a relatively small fraction of the lipid goes into the production of unilamellar vesicles with sizes detectable with optical microscopy.     

Nonspecific hydrophobic interactions of a repressor protein, PhaR, with poly[(R)-3-hydroxybutyrate] film studied with a quartz crystal microbalance

The gene expression for phasins (PhaP), which are predominantly polyhydroxyalkanoates (PHAs) granule-associated proteins, is regulated by a repressor protein of PhaR through the dual binding abilities of PhaR to the target DNAs and the granules. In this study, the binding functions of PhaR to poly[(R)-3-hydroxybutyrate] (P(3HB)) were investigated quantitatively by using a quartz crystal microbalance (QCM) technique. Adsorption of PhaR onto a melt-crystallized film of P(3HB) (cr-P(3HB)) was detected as a negative frequency shift of the QCM. The time course of the frequency changes observed for PhaR adsorption was composed of a quick frequency decrease at an initial stage and a subsequent slower frequency decrease for several hours, indicating multilayered adsorption of PhaR molecules onto cr-P(3HB). The initial rapid adsorption, which corresponds to direct adsorption of PhaR molecules onto a bare surface of cr-P(3HB), was a diffusion-controlled process. Strong interactions between PhaR and cr-P(3HB) were also observed as apparently irreversible adsorption. The comparative QCM measurement of PhaR adsorption onto various types of polymers with different aliphatic chemical structures revealed that PhaR was adsorbed onto the surfaces of polymers, including cr-P(3HB), mainly by nonspecific hydrophobic interactions. These results illustrate the high affinity and low specificity for adsorption of PhaR to P(3HB).     

Layer-by-layer films made from extracellular matrix macromolecules on silicone substrates

The layer-by-layer (LbL) technique has been widely used to produce nanofilms for biomedical applications. Naturally occurring polymers such as ECM macromolecules are attractive candidates for LbL film preparation. In this study, we assessed the build-up of type I collagen (Col1)/chondroitin sulfate (CS) or Col1/Heparin (HN) on polydimethylsiloxane (PDMS) substrates. The build-up was assessed by quartz crystal microbalance with dissipation (QCM-D) and atomic force microscopy (AFM). Integrin-mediated cell adhesion was assessed by studying the cytoskeletal organization of mammalian primary cells (chondrocytes) seeded on different end layers and number of layers. Data generated from the QCM-D observations showed a consistent build-up of films with more adsorption in the case of Col1/HN. Col1/CS films were stable in media, whereas Col1/HN films were not. AFM analysis showed that the layers were fibrillar in structure for both systems and between 20 and 30 nm thick. The films promoted cell adhesion when compared with tissue culture plastic in serum-free media with cycloheximide. Crosslinking of the films resulted in constrained cell spreading and a ruffled morphology. Finally, beta1 integrin blocking antibodies prevented cell spreading, suggesting that cell adhesion and spreading were mediated mainly by interaction with the collagen fibrils. The ability to construct stable ECM-based films on PDMS has particular relevance in mechanobiology, microfluidics, and other biomedical applications.     

Novel quartz crystal microbalance based biosensor for detection of oral epithelial cell-microparticle interaction in real-time

Recent applications of quartz crystal resonant sensor technology to monitor cell adhesion and specific ligand interaction processes has triggered the development of a new category of quartz crystal microbalance (QCM) based biosensors. In this study human oral epithelial cells (H376) were cultured on quartz sensors and their response to microspheres investigated in situ using the QCM technique. The results demonstrated that this novel biosensor was able to follow cell-microsphere interactions in real-time and under conditions of flow as would occur in the oral cavity. Unique frequency profiles generated in response to the microspheres were postulated to be due to phases of mass addition and altered cellular rigidity. Supporting microscopic evidence demonstrated that the unique frequency responses obtained to these interactions were in part due to binding between the cell surface and the microspheres. Furthermore, a cellular uptake process, in response to microsphere loading was identified and this, by influencing the rigidity of the cellular cytoskeleton, was also detectable through the frequency responses obtained.