Decreased biocide susceptibility of adherent Legionella pneumophila.

In a study of the in vitro effectiveness of biocides against Legionella pneumophila, some aspects of the cooling tower environment were replicated in the laboratory, paying particular attention to water hardness and pH. Pieces of Douglas fir and polyvinyl chloride were colonized in a recirculating system and the comparative efficacy of two biocides (Bronopol and Kathon) against the sessile and planktonic populations was examined. While the biocides were relatively effective against the planktonic L. pneumophila population over a short period of time (minimum 9-12 h), substantially longer periods of time (maximum greater than 48 h) were required to reduce the number of cultivable bacteria to below detectable levels in the adherent population. The results indicate that failure to monitor the sessile population of L. pneumophila in laboratory studies of biocides may result in the use of incorrect dosages and/or contact times in field trials with apparently reduced in situ efficacy.     

The use of biocides to control sulphate‐reducing bacteria in biofilms on mild steel surfaces

Three different types of biocides, viz. formaldehyde (FM), glutaraldehyde (GA) and isothiozolone (ITZ) were used to control planktonic and sessile populations of two marine isolates of sulphate‐reducing bacteria (SRB). The influence of these biocides on the initial attachment of cells to mild steel surfaces, on subsequent biofilm formation and on the activity of hydrogenase enzymes within developed biofilms was evaluated. In the presence of biocides the rate and degree of colonization of mild steel by SRB depended on incubation time, bacterial isolate and the type of biocide used. Although SRB differed in their susceptibility to biocides, for all isolates the biofilm population was more resistant to the treatment than the planktonic population. GA showed highest efficiency in controlling planktonic and sessile SRB compared with the other two biocides. The activity of the enzyme hydrogenase measured in SRB biofilms varied between isolates and with the biocide treatment. No correlation was found between the number of sessile cells and hydrogenase activity.     

Efficacy of a quaternary ammonium compound against planktonic and sessile populations of differentLegionella pneumophila strains

Efficacy of Gemacide PN-50^TM (a quaternary ammonium compound) as a commercial formulation recommended for disinfecting heat exchangers was determined for both planktonic and sessile populations of variousLegionella pneumophila strains. The quaternary ammonium compound (QAC) was preferred as an alternative due to the emerging resistance of potentially pathogenic bacteria against different biocides. PlanktonicL. pneumophila strains were suspended in tap water while sessile ones were grown on stainless steel that is used in construction of the cooling towers, then both group of strains were exposed to the biocide. The sensitivity of both planktonic and sessile populations ofL. pneumophila strains to the biocide was different. The biocide was found effective below recommended dosages (1000–2000 mg/L) against planktonic populations ofL. pneumophila, whereas it was determined that higher than the recommended dosages were required for sessile populations. The environmental isolates were more resistant to the biocide than the ATCC isolate was. The results indicated that studying only the planktonic populations ofL. pneumophila for biocide tests might not be sufficient to provide the optimum dosage and contact time information for field trials. Therefore, biocidal activity of a water treatment chemical must be evaluated in terms of dosage and contact times on both planktonic and sessile bacteria.     

Relationship between Legionella pneumophila and Acanthamoeba polyphaga: physiological status and susceptibility to chemical inactivation.

Survival studies were conducted on Legionella pneumophila cells that had been grown intracellularly in Acanthamoeba polyphaga and then exposed to polyhexamethylene biguanide (PHMB), benzisothiazolone (BIT), and 5-chloro-N-methylisothiazolone (CMIT). Susceptibilities were also determined for L. pneumophila grown under iron-sufficient and iron-depleted conditions. BIT was relatively ineffective against cells grown under iron depletion; in contrast, iron-depleted conditions increased the susceptibilities of cells to PHMB and CMIT. The activities of all three biocides were greatly reduced against L. pneumophila grown in amoebae. PHMB (1 x MIC) gave 99.99% reductions in viability for cultures grown in broth within 6 h and no detectable survivors at 24 h but only 90 and 99.9% killing at 6 h and 24 h, respectively, for cells grown in amoebae. The antimicrobial properties of the three biocides against A. polyphaga were also determined. The majority of amoebae recovered from BIT treatment, but few, if any, survived CMIT treatment or exposure to PHMB. This study not only shows the profound effect that intra-amoebal growth has on the physiological status and antimicrobial susceptibility of L. pneumophila but also reveals PHMB to be a potential biocide for effective water treatment. In this respect, PHMB has significant activity, below its recommended use concentrations, against both the host amoeba and L. pneumophila.     

Relationship between Legionella pneumophila and Acanthamoeba polyphaga: physiological status and susceptibility to chemical inactivation.

Survival studies were conducted on Legionella pneumophila cells that had been grown intracellularly in Acanthamoeba polyphaga and then exposed to polyhexamethylene biguanide (PHMB), benzisothiazolone (BIT), and 5-chloro-N-methylisothiazolone (CMIT). Susceptibilities were also determined for L. pneumophila grown under iron-sufficient and iron-depleted conditions. BIT was relatively ineffective against cells grown under iron depletion; in contrast, iron-depleted conditions increased the susceptibilities of cells to PHMB and CMIT. The activities of all three biocides were greatly reduced against L. pneumophila grown in amoebae. PHMB (1 x MIC) gave 99.99% reductions in viability for cultures grown in broth within 6 h and no detectable survivors at 24 h but only 90 and 99.9% killing at 6 h and 24 h, respectively, for cells grown in amoebae. The antimicrobial properties of the three biocides against A. polyphaga were also determined. The majority of amoebae recovered from BIT treatment, but few, if any, survived CMIT treatment or exposure to PHMB. This study not only shows the profound effect that intra-amoebal growth has on the physiological status and antimicrobial susceptibility of L. pneumophila but also reveals PHMB to be a potential biocide for effective water treatment. In this respect, PHMB has significant activity, below its recommended use concentrations, against both the host amoeba and L. pneumophila.     

Efficacy of biocides on laboratory-generated Legionella biofilms

Results of biocide efficacy testing on laboratory-generated microbial biofilms containing Legionella bozemanii is presented. These show that chlorine is effective at recommended concentrations in cooling towers; at least 48 h contact between free chlorine and the biofilm is necessary. Of five commercial biocides tested, those containing isothiazolinones and dibromonitrilo-proprionamide were most effective against sessile L. bozemanii.     

Ecological behaviour of three serogroups of Legionella pneumophila within a model plumbing system

Three Legionella pneumophila strains isolated from water samples and belonging to serogroups (sgs) 1, 6 and 9 were analysed for their capacity to colonise an experimental model simulating a domestic hot water distribution system. Ecological factors that could influence the persistence of the sgs such as intracellular life within protozoan hosts and bacterial interference by the production of antagonistic compounds were also studied. Viable counts of L. pneumophila increased both in the planktonic and in the sessile phases. Sg 6 showed a marked prevalence during the whole experiment and exhibited the highest host infection efficiency. Sg 1 was significantly less represented, but showed the highest capacity to reproduce in the protozoan hosts. Sg 9 was poorly represented and less adapted to intracellular life. Among the 14 bacteria constantly isolated in the system, five (35.7%) produced antagonistic substances against Legionella, with differences according to the bacterial strain and L. pneumophila sgs.     

Planktonic replication is essential for biofilm formation by Legionella pneumophila in a complex medium under static and dynamic flow conditions

Legionella pneumophila persists for a long time in aquatic habitats, where the bacteria associate with biofilms and replicate within protozoan predators. While L. pneumophila serves as a paradigm for intracellular growth within protozoa, it is less clear whether the bacteria form or replicate within biofilms in the absence of protozoa. In this study, we analyzed surface adherence of and biofilm formation by L. pneumophila in a rich medium that supported axenic replication. Biofilm formation by the virulent L. pneumophila strain JR32 and by clinical and environmental isolates was analyzed by confocal microscopy and crystal violet staining. Strain JR32 formed biofilms on glass surfaces and upright polystyrene wells, as well as on pins of "inverse" microtiter plates, indicating that biofilm formation was not simply due to sedimentation of the bacteria. Biofilm formation by an L. pneumophila fliA mutant lacking the alternative sigma factor sigma(28) was reduced, which demonstrated that bacterial factors are required. Accumulation of biomass coincided with an increase in the optical density at 600 nm and ceased when the bacteria reached the stationary growth phase. L. pneumophila neither grew nor formed biofilms in the inverse system if the medium was exchanged twice a day. However, after addition of Acanthamoeba castellanii, the bacteria proliferated and adhered to surfaces. Sessile (surface-attached) and planktonic (free-swimming) L. pneumophila expressed beta-galactosidase activity to similar extents, and therefore, the observed lack of proliferation of surface-attached bacteria was not due to impaired protein synthesis or metabolic activity. Cocultivation of green fluorescent protein (GFP)- and DsRed-labeled L. pneumophila led to randomly interspersed cells on the substratum and in aggregates, and no sizeable patches of clonally growing bacteria were observed. Our findings indicate that biofilm formation by L. pneumophila in a rich medium is due to growth of planktonic bacteria rather than to growth of sessile bacteria. In agreement with this conclusion, GFP-labeled L. pneumophila initially adhered in a continuous-flow chamber system but detached over time; the detachment correlated with the flow rate, and there was no accumulation of biomass. Under these conditions, L. pneumophila persisted in biofilms formed by Empedobacter breve or Microbacterium sp. but not in biofilms formed by Klebsiella pneumoniae or other environmental bacteria, suggesting that specific interactions between the bacteria modulate adherence.     

Effects of three oxidizing biocides on Legionella pneumophila serogroup 1

A study was conducted to determine the bactericidal effects of ozone and hydrogen peroxide relative to that of free chlorine on Legionella pneumophila serogroup 1. In laboratory batch-type experiments, organisms seeded at various densities were exposed to different concentrations of these biocides in demand-free buffers. Bactericidal effects were measured by determining the ability of L. pneumophila to grow on buffered charcoal-yeast extract agar supplemented with alpha-ketoglutarate. Ozone was the most potent of the three biocides, with a greater than 99% kill of L. pneumophila occurring during a 5-min exposure to 0.10 to 0.30 micrograms of O3 per ml. The bactericidal action of O3 was not markedly affected by changes in pH or temperature. Concentrations of 0.30 and 0.40 micrograms of free chlorine per ml killed 99% of the L. pneumophila after 30- and 5-min exposures, respectively. A 30-min exposure to 1,000 micrograms of H2O2 per ml was required to effect a 99% reduction of the viable L. pneumophila population. However, no viable L. pneumophila could be detected after a 24-h exposure to 100 or 300 micrograms of H2O2 per ml. Attempts were made to correlate the biocidal effects of O3 and H2O2 with the oxidation of L. pneumophila fatty acids. These tests indicated that certain biocidal concentrations of O3 and H2O2 resulted in a loss or severe reduction of L. pneumophila unsaturated fatty acids.     

Effects of three oxidizing biocides on Legionella pneumophila serogroup 1.

A study was conducted to determine the bactericidal effects of ozone and hydrogen peroxide relative to that of free chlorine on Legionella pneumophila serogroup 1. In laboratory batch-type experiments, organisms seeded at various densities were exposed to different concentrations of these biocides in demand-free buffers. Bactericidal effects were measured by determining the ability of L. pneumophila to grow on buffered charcoal-yeast extract agar supplemented with alpha-ketoglutarate. Ozone was the most potent of the three biocides, with a greater than 99% kill of L. pneumophila occurring during a 5-min exposure to 0.10 to 0.30 micrograms of O3 per ml. The bactericidal action of O3 was not markedly affected by changes in pH or temperature. Concentrations of 0.30 and 0.40 micrograms of free chlorine per ml killed 99% of the L. pneumophila after 30- and 5-min exposures, respectively. A 30-min exposure to 1,000 micrograms of H2O2 per ml was required to effect a 99% reduction of the viable L. pneumophila population. However, no viable L. pneumophila could be detected after a 24-h exposure to 100 or 300 micrograms of H2O2 per ml. Attempts were made to correlate the biocidal effects of O3 and H2O2 with the oxidation of L. pneumophila fatty acids. These tests indicated that certain biocidal concentrations of O3 and H2O2 resulted in a loss or severe reduction of L. pneumophila unsaturated fatty acids.     

Use of dissolved ozone for controlling planktonic and sessile bacteria in industrial cooling systems

Cooling water treatment requires effective, environmentally-safe biocides compatible with system operation. The unique combination of high biocidal activity during use with no toxic discharge, could render dissolved ozone a safe biocide for cooling water treatment. Planktonic and sessile cells of Pseudomonas fluorescens (a frequent microbial contaminant of industrial systems) were used in this work to assess the biocidal effectiveness of ozone. Dissolved ozone showed to be effective at concentrations between 0.1 and 0.3 ppm, to eliminate completely the levels of planktonic cells used in this paper (10⁷–10⁸ cell/ml) within a range of contact times between 10 and 30 min. However, ozone at 0.15 ppm was only able to diminish sessile cell population by two or three orders of magnitude. This minor biocidal effectiveness of ozone against bacterial biofilms is discussed in this paper, taking into account recent concepts on structure and dynamics of biofilms. Different metallic substrata were assayed to verify if there was any effect of metal nature on the biocidal action. Open circuit potentials vs. time experiments and potentiodynamic polarization curves were made for assessing the effect of dissolved ozone on the corrosion behavior of the metals tested.     

The efficacy of biocides and other chemical additives in cooling water systems in the control of amoebae

Aims:  In vitro experiments were undertaken to evaluate biocide formulations commonly used in cooling water systems against protozoa previously isolated from cooling towers. The investigations evaluated the efficacy of these formulations against amoebic cysts and trophozoites.
Methods and Results:  Laboratory challenges against protozoa isolated from cooling towers using chlorine, bromine and isothiazolinone biocides showed that all were effective after 4 h. The presence of molybdate and organic phosphates resulted in longer kill times for bromine and isothiazolinones. All treatments resulted in no detectable viable protozoa after 4 h of exposure.
Conclusions:  The chemical disinfection of planktonic protozoa in cooling water systems is strongly influenced by the residence time of the formulation and less so by its active constituent. Bromine and isothiazolinone formulations may require higher dosage of concentrations than currently practiced if used in conjunction with molybdate- and phosphate-based scale/corrosion inhibitors.
Significance and Impact of the Study:  Cooling water systems are complex microbial ecosystems in which predator–prey relationships play a key role in the dissemination of Legionella . This study demonstrated that at recommended dosing concentrations, biocides had species-specific effects on environmental isolates of amoebae that may act as reservoirs for Legionella multiplication in cooling water systems.     

A laboratory apparatus for the generation and biocide efficacy testing of Legionella biofilms

P.N. GREEN AND R.S. PIRRIE. 1993. The construction and operation of a laboratory biofilm generator designed to grow sessile populations of legionellas for biocide efficacy testing is described. Some examples of static biocide testing on both sessile and planktonic populations of Legionella bozemanii are discussed along with other potential applications of the apparatus.     

Assessment of resistance towards biocides following the attachment of micro-organisms to, and growth on, surfaces

AIMS: To develop a rapid method for the assessment of biocidal activity directed towards intact biofilms. METHODS AND RESULTS: Escherichia coli and Staphylococcus epidermidis were cultured for up to 48 h within 96-well microtitre plates. The planktonic phase was removed and the wells rinsed. Residual biofilms were exposed to various concentrations of chloroxylenol, peracetic acid, polyhexamethylene biguanide (PHMB), cetrimide or phenoxyethanol for 1 h. At 15-min intervals, biocide was removed, and the wells washed in neutraliser and filled with volumes of fresh medium. Re-growth of the cultures was monitored during incubation at 35 degrees C in the plate reader. Times taken for the treated wells to re-grow to fixed endpoints were determined and related to numbers of surviving cells. Time--survival curves were constructed and the survival of the attached bacteria, following exposure to the agents for 30 min, interpolated for each biocide concentration. Log--log plots of these survival data and biocide concentration were constructed, and linear regression analysis performed in order to (i) calculate concentration exponents and (ii) compare the effectiveness of the biocides between variously aged biofilm and planktonic cells. From such analyses iso-effective concentrations of biocide (95% kill in 30 min) were calculated and expressed as planktonic : biofilm indices (PBI). CONCLUSION: PBI varied between 1.02 and 0.02, were relatively unaffected by age of the biofilms but differed significantly between organism and biocide. Notably those compounds with the higher activity against planktonic bacteria (PHMB and peracetic acid) were most prone to a biofilm effect but remained the most effective of the agents selected. SIGNIFICANCE AND IMPACT OF THE STUDY: The endpoint method proved robust, enabled the bactericidal effects of the biocides to be assessed against in-situ biofilms, and was suitable for routine screening applications.     

Efficacy of bromochlorodimethylhydantoin againstLegionella pneumophila in industrial cooling water

Summary Free residual chlorine and bromine can be generated in water from bromochlorodimethylhydantoin (BCDMH). Efficacy of chlorine from inorganic sources has been studied extensively, but there is much less information on the efficacy of bromine againstL. pneumophila; only a few efficacy studies of organically-derived. halogen appear in the literature and the results from different studies conflict or are difficult to interpret. This paper describes the efficacy of halogen from BCDMH against planktonic, pure cultureL. pneumophila in an industrial cooling water. There was no difference in efficacy between halogen derived from organic or inorganic sources in controlled laboratory experiments. Effective doses in laboratory studies cannot be translated directly to field applications because of significant differences in the microbiology. However, the data suggest that disinfection (>99.9% reduction in viability within 10 min) of planktonic, pure cultureL. pneumophila can be achieved with about 1 ppm free residual halogen (expressed as chlorine) from BCDMH in a typical industrial cooling water.     

Influence of temperature and plumbing material selection on biofilm formation and growth of Legionella pneumophila in a model potable water system containing complex microbial flora.

Survival and growth of Legionella pneumophila in both biofilm and planktonic phases were determined with a two-stage model system. The model used filter-sterilized tap water as the sole source of nutrient to culture a naturally occurring mixed population of microorganisms including virulent L. pneumophila. At 20 degrees C, L. pneumophila accounted for a low proportion of biofilm flora on polybutylene and chlorinated polyvinyl chloride, but was absent from copper surfaces. The pathogen was most abundant on biofilms on plastics at 40 degrees C, where it accounted for up to 50% of the total biofilm flora. Copper surfaces were inhibitory to total biofouling and included only low numbers of L. pneumophila organisms. The pathogen was able to survive in biofilms on the surface of the plastic materials at 50 degrees C, but was absent from the copper surfaces at the same temperature. L. pneumophila could not be detected in the model system at 60 degrees C. In the presence of copper surfaces, biofilms forming on adjacent control glass surfaces were found to incorporate copper ions which subsequently inhibited colonization of their surfaces. This work suggests that the use of copper tubing in water systems may help to limit the colonization of water systems by L. pneumophila.     

Irradiation sensitivity of planktonic and biofilm-associated Escherichia coli O157:H7 isolates is influenced by culture conditions

Ionizing radiation effectively inactivates Escherichia coli O157:H7, but the efficacy of the process against biofilm cells versus that against free-living planktonic cells is not well documented. The radiation sensitivity of planktonic or biofilm cells was determined for three isolates of E. coli O157:H7 (C9490, ATCC 35150, and ATCC 43894). Biofilms were formed on sterile glass slides incubated at 37 degrees C for either 24 h, 48 h, or 72 h. The biofilm and planktonic cultures were gamma irradiated at doses ranging from 0.0 (control) to 1.5 kGy. The dose of radiation value required to reduce the population by 90% (D10) was calculated for each isolate, culture, and maturity based on viable populations at each radiation dose. For each of the times sampled, the D10 values of isolate 43894 planktonic cells (0.454 to 0.479 kGy) were significantly (P<0.05) higher than those observed for biofilm cells (0.381 to 0.385 kGy), indicating a significantly increased sensitivity to irradiation for cells in the biofilm habitat. At the 24-h sampling time, isolate C9490 showed a similar pattern, in which the D10 values of planktonic cells (0.653 kGy) were significantly higher than those for biofilm cells (0.479 kGy), while isolate 35150 showed the reverse, with D10 values of planktonic cells (0.396 kGy) significantly lower than those for biofilm cells (0.526 kGy). At the 48-h and 72-h sampling times, there were no differences in radiation sensitivities based on biofilm habitat for C9490 or 35150. Biofilm-associated cells, therefore, show a response to irradiation which can differ from that of planktonic counterparts, depending on the isolate and the culture maturity. Culture maturity had a more significant influence on the irradiation efficacy of planktonic cells but not on biofilm-associated cells of E. coli O157:H7.     

Analysis of biocide transport limitation in an artificial biofilm system

An alginate gel bead artificial biofilm system was used to assay biofilm susceptibility to four biocides and to analyse the extent to which each agent penetrated the biofilm. Chlorine, glutaraldehyde, an isothiazolone, and a quaternary ammonium compound were tested on alginate-entrapped Enterobacter aerogenes in gel beads ranging from 1·8 to 6 mm in diameter. Gel-entrapped bacteria were less susceptible to all four antimicrobial agents than were planktonic micro-organisms. The degree of kill measured in artificial biofilm gel beads depended on the size of the gel bead and the cell density at which it was loaded. Disinfection efficacy decreased as gel bead radius or cell density increased. The manifest dependence of biofilm disinfection efficacy on the physical properties of the artificial biofilm (radius and cell density) suggests the impingement of transport limitation of biocide transport into the biofilm. A previously developed theory of biocide reaction and diffusion in biofilm was tested by calculating an appropriate Thiele modulus. In accordance with the theory, the efficacy of all four biocides decreased, albeit noisily, as the Thiele modulus exceeded 1. This result demonstrates that transport limitation can impact antimicrobial performance against biofilms not only of oxidizing biocides but also of non-oxidizing agents.     

Use of heterotrophic CO2 assimilation as a measure of metabolic activity in planktonic and sessile bacteria

We have examined whether assimilation of CO2 can be used as a measure of metabolic activity in planktonic and sessile heterotrophic bacteria. CO2 assimilation by environmental samples and pure cultures of heterotrophic bacteria was studied using 14CO2 and 13CO2 as tracers. Heterotrophic growth on complex organic substrates resulted in assimilation of CO2 into cell biomass by activated sludge, drinking water biofilm, and pure cultures of Escherichia coli ATCC 25922, Es. coli ATCC 13706, Rhodococcus ruber, Burkholderia sp., Bacillus circulans, Pseudomonas putida, Pseudomonas stutzeri, and Pseudomonas aeruginosa. Analysis of 13C-labelled phospholipid fatty acids (PLFAs) confirmed that heterotrophic bacteria may assimilate 13CO2 into cell macromolecules such as membrane lipids. All major PLFAs extracted from activated sludge and drinking water biofilm samples were enriched in 13C after incubation with CO2. Between 1.4% and 6.5% of the biomass produced by cultures of P. putida and a drinking water biofilm during growth in complex media was apparently derived from assimilation of CO2. Resting cells assimilated less CO2 compared to actively growing cells, and CO2 assimilation activity correlated with the amount of biomass produced during heterotrophic growth. The 14CO2 assimilation assay was evaluated as a tool to examine inhibitory effects of biocides on planktonic and sessile heterotrophs (biofilms). On the basis of 14CO2 assimilation activity, the minimum inhibitory concentration (MIC) of benzalkonium chloride was estimated to 21.1 and 127.2 mg l(-1) for planktonic and biofilm samples, respectively. The results indicate that assimilation of isotopically labelled CO2 can be used as a relatively simple measure of metabolic activity in heterotrophic bacteria. CO2 assimilation assays may be used to study the effects of antimicrobial agents on growth and survival of planktonic and sessile heterotrophic organisms.     

The effect of industrial biocides on sulphate-reducing bacteria under high pressure

This study was undertaken to determine the influence of temperature (20, 37, and 50°C) and pressure (1, 100 and 200 atm) on a strain of sulphate-reducing bacteria (SRB), isolated from an oil reservoir in Alaska. The effect of different concentrations (100, 200 and 500 ppm) of biocides isothiazolone (ITZ) and formaldehyde (FA) on planktonic population of SRB was tested in order to determine the efficacy of biocides under these conditions.The highest bacterial growth rate was 0.26±0.03 h⁻¹ at 37°C under pressure of 100 atm. Statistical evaluation showed that although both temperature and pressure had exerted an effect on bacteria by significantly increasing their growth rate; temperature rather than pressure had greater influence on bacterial proliferation.The effectiveness of both FA and ITZ in controlling planktonic populations of SRB was comparable except at 37°C/200 atm, under which conditions FA proved to be more potent. The effectiveness of both biocides decreased with an increase in cell number, as observed at 37°C/100 atm.