Rapid and onsite BOD sensing system using luminous bacterial cells-immobilized chip

A BOD monitoring system based on a bio-chip which immobilized luminous bacterium in micrometer-order holes were arrayed and fabricated by micro-machine techniques, was developed. The acrylic chip (3 cmx3 cm) comprises nine micro-holes (diameter: 700 microm or 1 mm, depth: 100 microm) arranged in a three by three array. Cells of the marine luminous bacterium, Photobacterium phosphoreum IFO 13896, which was grown at 15 degrees C for 15 h, were immobilized with 3% or 15% sodium alginate gel. BOD standard solutions or actual sample solution (approximately 10 microl) was fallen onto the cell-arrayed chip, and then the chip was incubated at 25 degrees C for 25 min. After incubation, bioluminescence from the each hole was gray-scaled and measured by a chemi-imager or newly developed onsite-type-monitoring system using a digital camera and a mobile-type personal computer. BOD values less than 16 ppm could detect by the chip, in particular, linear relationship at the concentrations between 0 and 16 ppm could be observed when luminous cells were immobilized with 3% sodium alginate gel. Steady bioluminescence was observed on the chip in the presence of BOD standard solution (GGA solution) which contained mineral elements. Furthermore, simultaneous detection of BOD values in various samples could be employed in the single chip. These results showed that the monitoring system with bio-chip could achieve high-through-put and onsite BOD detection. Our newly developed onsite-type BOD detection system which was used a digital camera and a (mobile) laptop computer was applied to measure and detect organic pollution due to biodegradable substances in wastewater treatment system. The same performance as the chemi-imager system was obtained for data of bioluminescence. The obtained BOD values showed a similar correlation with that of the conventional method for BOD determination (BOD5). These results suggested for successful achievement of high-though-put and onsite detection of BOD in practical.     

A novel BOD sensor based on bacterial luminescence

A reagent-type BOD sensor with a new principle employing a luminous bacterium, Photobacterium phosphoreum, was developed. The increased intensity of luminescence resulting from the cellular assimilation of organic compounds in wastewater was detected by a photodiode. The BOD response of the bacterial reagent could be obtained within 15 min with +/-7% error. The temperature condition for optimal BOD response was 18 degrees to 25 degrees C at pH 7 to 8, indicating that it is possible to measure BOD at room temperature without having to stabilize the temperature of the measuring system. For practical use, two procedures for long-term preservation of the bacterial reagent, vacuum drying method and freezing method, are suggested. The metabolic characteristics of employed luminous bacteria were investigated by comparing the BOD values for several pure organic substrates estimated by the BOD sensor with conventional 5-day BOD values. In comparison with the 5-day measurement for some wastewater samples, BOD values estimated by the sensor showed comparatively good agreement with those measured by the 5-day method. (c) 1993 Wiley & Sons, Inc.     

A spectrophotometric biochemical oxygen demand determination method using 2,6-dichlorophenolindophenol as the redox color indicator and the eukaryote Saccharomyces cerevisiae

A method to determine the spectrophotometric biochemical oxygen demand (BOD(sp)) was studied with high sensitivity and reproducibility by employing 2,6-dichlorophenolindophenol (DCIP) as a redox color indicator, the yeast Saccharomyces cerevisiae, and a temperature-controlling system providing a three-consecutive-stir unit. The absorbance of DCIP decreased due to the metabolism of organic substances in aqueous samples by S. cerevisiae. Under optimum conditions, a calibration curve for glucose glutamic acid concentration between 1.1 and 22mg O(2) L(-1) (r=0.988, six points, n=3) was obtained when the incubation mixture was incubated for 10min at 30 degrees C. The reproducibility of the optical responses in the calibration curve was 1.77% (average of relative standard deviations; RSD(av)). Subsequently, the characterization of this method was studied. The optical responses to pure organic substances and the influence of chloride ions, artificial seawater, and heavy metal ions on the sensor response were investigated before use with real samples. Measurements of real samples using river water were performed and compared with those obtained using the BOD(5) method. Finally, stable responses were obtained for 36 days when the yeast cell suspension was stored at 4 degrees C (response reduction, 89%; RSD(av) value for 9 testing days, 8.4%).     

Enumeration of bacterial cell numbers by amplified firefly bioluminescence without cultivation

We recently developed a novel bioluminescent enzymatic cycling assay for ATP and AMP with the concomitant use of firefly luciferase and pyruvate orthophosphate dikinase (PPDK), where AMP and pyrophosphate produced from ATP by firefly luciferase were converted back into ATP by PPDK. Background luminescence derived from contaminating ATP and AMP in the reagent was reduced using adenosine phosphate deaminase which degrades ATP, ADP, and AMP, resulting in constant and highly amplified bioluminescence with low background luminescence. To detect bacterial cells without cultivation, we applied the above bioluminescent enzymatic cycling reagent to rapid microbe detection system. ATP spots (0.31-5.0 amol/spot) at the level of a single bacterial cell were detected with 5 min signal integration, signifying that integrated luminescence was amplified 43 times in comparison to traditional ATP bioluminescence. Consequently, Escherichia coli, Staphylococcus aureus, Pseudomonas aeruginosa, and Lactobacillus brevis in beer were detected without cultivation. Significant correlation was observed between the number of signal spots obtained using this novel system and the colony-forming units observed with the conventional colony-counting method (R(2)=0.973).     

生物传感器快速测定BOD的研究

生化需氧量(biochemicaloxygendemand,BOD)是一种表征水体有机污染程度的综合指标,广泛应用于水体监测和废水处理厂的运行控制。由于BOD的标准测定方法需时5天,不能及时地反映水质状况和反馈处理信息,因此快速测定BOD的方法和仪器化研究近年来得到广泛的重视。利用生物传感器测定BOD是一种有效地快速测定废水中可生化降解有机物的方法。介绍生物传感器的工作原理及其生物敏感材料,讨论BOD传感器的性能参数以及BOD快速测定值(BODst)与标准BOD5值的一致性问题。对现阶段市场上常见的几种BOD快速测定仪进行简单的介绍,并对它们的性能进行比较 。     

Evaluation of the properties of potassium ferrate used for water purification by luminescence bioassay

Characteristics of four natural water samples from urban and rural areas and the efficiency of a new purifying agent, potassium ferrate K₂FeO₄, were studied by bacterial luminescence bioassay for 30 minutes. It was revealed that two samples of water from the urban areas are toxic, while the other two samples (one from urban and one from rural environment) are nontoxic. Numerous data obtained on the increase in toxicity index with time allow reasonable conclusions to be made about the chemical nature of substances present in the test water samples. Toxic natural water samples were likely to contain heavy metals and were well purified using potassium ferrate, including via their adsorption. In nontoxic natural water samples, toxic complexes with organic compounds present in water could form at the addition of potassium ferrate. The obtained data call for further studying the properties of potassium ferrate complexes with organic compounds. Bacterial luminescence bioassay is a promising method for the rapid assessment of properties of various water sources (their integral toxicity and presumable chemical composition) and new reagents for their purification (effective concentrations, bactericidal properties, and mechanisms of interacting with heavy metals and organic substances in water).     

Comparative study of semi-specific Aeromonas hydrophila and universal Pseudomonas fluorescens biosensors for BOD measurements in meat industry wastewaters

Aeromonas hydrophila P69.1 (A. hydrophila) was used to construct a semi-specific biosensor to estimate biochemical oxygen demand (BOD) in high fat and grease content wastewaters. A. hydrophila cells were grown in fat containing medium to induce necessary enzymes for transport and degradation of fatty substances. Universal biosensor based on non-specific Pseudomonas fluorescens P75 (P. fluorescens) was used to conduct comparison experiments. Biosensors were calibrated using OECD synthetic wastewater and steady-state method, subsequently several experiments with synthetic and industrial wastewaters were conducted. A linear range up to 45 mg l(-1) BOD(7) was gained using A. hydrophila biosensor, in comparison to 40 mg l(-1) BOD(7) obtained using P. fluorescens biosensors. The lower limit of detection was 5 mg l(-1) BOD(7). Service life of A. hydrophila and P. fluorescens biosensors were 110 and 115 days, respectively. The response time of the biosensors depended on the BOD(7) of measuring solution and was up to 20 min when analyzing different wastewaters. Both biosensors underestimated BOD in meat industry wastewater from 43% up to 71%, but more accurate results could be obtained with A. hydrophila biosensor. Semi-specific A. hydrophila biosensor was able to measure proportion of fat found in wastewater sample, while other refractory compounds remained undetectable to both biosensors.     

Stopped-flow system with ozonizer for the estimation of low biochemical oxygen demand in environmental samples

The stopped-flow system with an ozonizer was developed to estimate low biochemical oxygen demand (BOD) in rivers. Rivers contain many biopersistent organic compounds such as humic acid, lignin, and gum arabic. Free radicals generated by self-decomposition of ozone were used as powerful oxidants to split organic compounds. Ozonysis of the samples was carried out by 42.4 g N⁻¹ m⁻³ ozone for 3 min at pH 7.0. Artificial wastewater (AWW) solutions were employed as standard solutions for the calibrations of the BOD sensor. At a BOD of 1 mg l⁻¹, the sensor response after ozonation was 1.6-fold higher than that before ozonation. The response time of the BOD sensor was only 5 min, being independent of the concentrations, and the lower detection limit was 0.5 mg l⁻¹ BOD. The degradations of lignin and tannic acid by ozonation were 54.1 and 42.3%, respectively. In the biosensor responses by ozonation, lignin, gum arabic, and surfactant increased by double or more compared with previous responses. BOD in rivers was estimated using the stopped-flow system. Environmental samples pretreated with ozone gave high responses to the biosensor that were similar to those of the conventional BOD₅ method. Accordingly, a good correlation between the sensor and the conventional BOD₅ was obtained (r = 0.989). The system has to evolve the highly sensitive BOD determination.     

Whole-cell bacterial sensors for the monitoring of phosphate bioavailability

A phosphate sensor plasmid was constructed, in which the inducible promoter of the alkaline phosphatase gene (phoA) from Escherichia coli is fused to the bioluminescence genes from Vibrio fischeri. The reporter construct was introduced into E. coli MG1655 and the rhizosphere coloniser Pseudomonas fluorescens DF57, which produced light in a dose-dependent manner when exogenous phosphate concentrations fell below 60 and 40 microM, respectively. These strains also responded to various organic and inorganic phosphorus compounds. Their ability to distinguish the bioavailable portion of phosphate in standard solution was demonstrated using different phosphate ligands. When applying the bioassay to wastewater samples, luminescence patterns correlated with phosphate concentrations determined by standard chemical procedure. These results indicated that phoA::lux-based bacterial sensors may serve as tools for the assessment of phosphate bioavailability.     

QCM immunosensor detection of Escherichia coli O157:H7 based on beacon immunomagnetic nanoparticles and catalytic growth of colloidal gold

In this paper, we describe a novel method for detecting Escherichia coli (E. coli) O157:H7 by using a quartz crystal microbalance (QCM) immunosensor based on beacon immunomagnetic nanoparticles (BIMPs), streptavidin-gold, and growth solution. E. coli O157-BIMPs were magnetic nanoparticles loaded with polyclonal anti-E. coli O157:H7 antibody (target antibody, T-Ab) and biotin-IgG (beacon antibody, B-Ab) at an optimized ratio of 1:60 (T-Ab:B-Ab). E. coli O157:H7 was captured and separated by E. coli O157-BIMPs in a sample, and the streptavidin-gold was subsequently conjugated to E. coli O157-BIMPs by using a biotin-avidin system. Finally, the gold particles on E. coli O157-BIMPs were enlarged in growth solution, and the compounds containing E. coli O157:H7, E. coli O157-BIMPs, and enlarged gold particles were collected using a magnetic plate. The QCM immunosensor was fabricated with protein A from Staphylococcus aureus and monoclonal anti-E. coli O157:H7 antibody. The compounds decreased the immunosensor's resonant frequency. E. coli O157-BIMPs and enlarged gold particles were used as "mass enhancers" to amplify the frequency change. The frequency shift was correlated to the bacterial concentration. The detection limit was 23 CFU/ml in phosphate-buffered saline and 53 CFU/ml in milk. This method could successfully detect E. coli O157:H7 with high specificity and stability. The entire procedure for the detection of E. coli O157:H7 took only 4 h.     

Effect of addition of organic waste on reduction of Escherichia coli during cattle feces composting under high-moisture condition

To ensure Escherichia coli reduction during cattle feces composting, co-composting with a variety of organic wastes was examined. A mixture of dairy cattle feces and shredded rice straw (control) was blended with organic wastes (tofu residue, rice bran, rapeseed meal, dried chicken feces, raw chicken feces, or garbage), and composted using a bench-scale composter under the high-moisture condition (78%). The addition of organic waste except chicken feces brought about maximum temperatures of more than 55 degrees C and significantly reduced the number of E. coli from 10(6) to below 10(2)CFU/g-wet after seven days composting, while in the control treatment, E. coli survived at the same level as that of raw feces. Enhancements of the thermophilic phase and E. coli reduction were related to the initial amount of easily digestible carbon in mass determined as BOD. BOD value more than 166.2 mg O2/DMg brought about significant E. coli reduction.     

Assessment of organic pollution effect considering differences between lotic and lentic stream habitats

Based on the requirements of the Water Framework Directive, a macroinvertebrate-based assessment system to evaluate the ecological quality of streams has been developed by AQEM project consortium. In the Czech Republic the impact of organic pollution was principal pressure studied, but some morphological degradation of some sampling sites could not be avoided. A multimetric assessment system for three stream types was developed. Detrended Correspondence Analysis was used for the detection of the response of macroinvertebrate communities to the gradient of organic degradation. Significant relationships between abiotic (BOD, TOC, nutrients) and biotic (saprobic index, ASPT) indicators of organic enrichment/eutrophication were identified. Separate storage of the riffle and pool components of each multi-habitat sample allowed differences between these habitats to be compared in context of the metrics applied in the assessment system. Lotic and lentic habitats differed in taxonomic composition, ecological traits and biotic indices. The separate assessment of the riffle and pool parts of samples provides additional useful information when combined effects of organic pollution and morphological degradation are to be considered.     

Immobilized multi-species based biosensor for rapid biochemical oxygen demand measurement

To improve the practicability of rapid biochemical oxygen demand (BOD) method, we proposed a stable BOD sensor based on immobilizing multi-species BODseed for wastewater monitoring in the flow system. The activation time of the biofilm was greatly shortened for the biofilm prepared by BODseed in the organic-inorganic hybrid material. Some influence factors such as temperature, pH, and concentration of phosphate buffer solution (PBS) were investigated in detail in which high tolerance to environment was validated for the BOD sensor permitted a wide pH and PBS concentration ranges. The minimum detectable BOD was around 0.5 mg/l BOD under the optimized 1.0 mg/ml BODseed immobilized concentration. The as-prepared BOD sensor exhibited excellent stability and reproducibility for different samples. Furthermore, the as-prepared BOD biosensor displayed a notable advantage in indiscriminate biodegradation to different organic compounds and their mixture, similar to the character of conventional BOD(5) results. The results of the BOD sensor method are well agreed with those obtained from conventional BOD(5) method for wastewater samples. The proposed rapid BOD sensor method should be promising in practical application of wastewater monitoring.     

Continuous anaerobic treatment of wastewater from a kraft pulp mill

A pilot-scale study of the thermophilic anaerobic digestion of high-strength wastewater (evaporator condensate, EC) discharged from a kraft pulp production process was performed. The system consisted of a microfiltration (MF) membrane module for oily substances removal, a stripping system using evolved gas from the digester for sulfur compounds removal, an anaerobic fixed-bed bioreactor for methane fermentation, and an ultrafiltration (UF) membrane module for retention of a high density of bacterial cells. The bioreactor had a fixed-bed with an effective volume of 5 m³ packed with pumice stone. In a continuous run with only the MF membrane module for oily substances removal, the digester efficiency declined because of methanogenic inhibition by sulfur compounds. After fitting of the stripping system which used evolved gas from the digester, the inhibitive sulfur compounds in the EC were removed more than 80%, and high-loading and high-efficiency operation could be attained. The BOD loading and BOD removal of 35.5 kg BOD/m³/d and 93%, respectively were attained. By anaerobic treatment of the evaporator condensate waste before the conventional aerobic activated sludge method, the total costs would be reduced to ¥3.31/m³ wastewater compared with ¥4.53/m³-wastewater by the aerobic activated sludge method only. The stability of digester performance against interruption by feed stoppage was also examined.     

Time-resolved fluorescence-based assay for rapid detection of Escherichia coli

Fast and simple detection of pathogens is of utmost importance in health care and the food industry. In this article, a novel technology for the detection of pathogenic bacteria is presented. The technology uses lytic-specific bacteriophages and a nonspecific interaction of cellular components with a luminescent lanthanide chelate. As a proof of principle, Escherichia coli-specific T4 bacteriophage was used to infect the bacteria, and the cell lysis was detected. In the absence of E. coli, luminescent Eu³⁺–chelate complex cannot be formed and low time-resolved luminescence signal is monitored. In the presence of E. coli, increased luminescence signal is observed as the cellular contents are leached to the surrounding medium. The luminescence signal is observed as a function of the number of bacteria in the sample. The homogeneous assay can detect living E. coli in bacterial cultures and simulated urine samples within 25 min with a detection limit of 1000 or 10,000 bacterial cells/ml in buffer or urine, respectively. The detection limit is at the clinically relevant level, which indicates that the method could also be applicable to clinical settings for fast detection of urine bacteria.     

Rapid method for separation of bacterial DNA from humic substances in sediments for polymerase chain reaction.

The polymerase chain reaction (PCR) was used to amplify an Escherichia coli 16S ribosomal gene fragment from sediments with high contents of humic substances. Total DNA was extracted from 1 g of E. coli seeded or unseeded samples by a rapid freeze-and-thaw method. Several approaches (use of Bio-Gel P-6 and P-30 and Sephadex G-50 and G-200 columns, as well as use of the Stoffel fragment) were used to reduce interference with the PCR. The best results were obtained when crude DNA extracts containing humic substances were purified by using Sephadex G-200 spun columns saturated with Tris-EDTA buffer (pH 8.0). Eluted fractions were collected for PCR analyses. The amplified DNA fragment was obtained from seeded sediments containing fewer than 70 E. coli cells per g. Because only 1/100 of the eluted fractions containing DNA extracts from 70 cells per g was used for the PCR, the sensitivity of detection was determined to be less than 1 E. coli cell. Thus, DNA direct extraction coupled with this technique to remove interference by humic substances and followed by the PCR can be a powerful tool to detect low numbers of bacterial cells in environmental samples containing humic substances.     

Rapid method for separation of bacterial DNA from humic substances in sediments for polymerase chain reaction.

The polymerase chain reaction (PCR) was used to amplify an Escherichia coli 16S ribosomal gene fragment from sediments with high contents of humic substances. Total DNA was extracted from 1 g of E. coli seeded or unseeded samples by a rapid freeze-and-thaw method. Several approaches (use of Bio-Gel P-6 and P-30 and Sephadex G-50 and G-200 columns, as well as use of the Stoffel fragment) were used to reduce interference with the PCR. The best results were obtained when crude DNA extracts containing humic substances were purified by using Sephadex G-200 spun columns saturated with Tris-EDTA buffer (pH 8.0). Eluted fractions were collected for PCR analyses. The amplified DNA fragment was obtained from seeded sediments containing fewer than 70 E. coli cells per g. Because only 1/100 of the eluted fractions containing DNA extracts from 70 cells per g was used for the PCR, the sensitivity of detection was determined to be less than 1 E. coli cell. Thus, DNA direct extraction coupled with this technique to remove interference by humic substances and followed by the PCR can be a powerful tool to detect low numbers of bacterial cells in environmental samples containing humic substances.     

Bilirubin oxidase from Bacillus pumilus: a promising enzyme for the elaboration of efficient cathodes in biofuel cells

A CotA multicopper oxidase (MCO) from Bacillus pumilus, previously identified as a laccase, has been studied and characterized as a new bacterial bilirubin oxidase (BOD). The 59 kDa protein containing four coppers, was successfully over-expressed in Escherichia coli and purified to homogeneity in one step. This 509 amino-acid enzyme, having 67% and 26% sequence identity with CotA from Bacillus subtilis and BOD from Myrothecium verrucaria, respectively, shows higher turnover activity towards bilirubin compared to other bacterial MCOs. The current density for O(2) reduction, when immobilized in a redox hydrogel, is only 12% smaller than the current obtained with Trachyderma tsunodae BOD. Under continuous electrocatalysis, an electrode modified with the new BOD is more stable, and has a higher tolerance towards NaCl, than a T. tsunodae BOD modified electrode. This makes BOD from B. pumilus an attractive new candidate for application in biofuel cells (BFCs) and biosensors.     

Effects of dilution on dissolved oxygen depletion and microbial populations in the biochemical oxygen demand determination

The biochemical oxygen demand (BOD) value is still a key parameter that can determine the level of organics, particularly the content of biodegradable organics in water. In this work, the effects of sample dilution, which should be done inevitably to get appropriate dissolved oxygen (DO) depletion, on the measurement of 5-day BOD (BOD₅), was investigated with and without seeding using natural and synthetic water. The dilution effects were also evaluated for water samples taken in different seasons such as summer and winter because water temperature can cause a change in the types of microbial species, thus leading to different oxygen depletion profiles during BOD testing. The predation phenomenon between microbial cells was found to be dependent on the inorganic nutrients and carbon sources, showing a change in cell populations according to cell size after 5-day incubation. The dilution of water samples for BOD determination was linked to changes in the environment for microbial growth such as nutrition. The predation phenomenon between microbial cells was more important with less dilution. BOD₅ increased with the specific amount of inorganic nutrient per microbial mass when the natural water was diluted. When seeding was done for synthetic water samples, the seed volume also affected BOD due to the rate of organic uptake by microbes. BOD₅ increased with the specific bacterial population per organic source supplied at the beginning of BOD measurement. For more accurate BOD measurements, specific guidelines on dilution should be established.     

Comparative detection of bacterial adhesion to Caco-2 cells with ELISA, radioactivity and plate count methods

Different methods are used to study bacterial adhesion to intestinal epithelial cells, which is an important step in pathogenic infection as well as in probiotic colonization of the intestinal tract. The aim of this study was to compare the ELISA-based method with more conventional plate count and radiolabeling methods for bacterial adhesion detection. An ELISA-based assay was optimized for the detection of Bifidobacterium longum and Escherichia coli O157:H7, which are low and highly adherent bacteria, respectively. In agreement with previous investigations, a percentage of adhesion below 1% was obtained for B. longum with ELISA. However, high nonspecific background and low positive signals were measured due to the use of polyclonal antibodies and the low adhesion capacity with this strain. In contrast, the ELISA-based method developed for E. coli adhesion detected a high adhesion percentage (15%). For this bacterium the three methods tested gave similar results for the highest bacterial concentrations (6.8 Log CFU added bacteria/well). However, differences among methods increased with the addition of decreased bacterial concentration due to different detection thresholds (5.9, 5.6 and 2.9 Log CFU adherent bacteria/well for radioactivity, ELISA and plate count methods, respectively). The ELISA-based method was shown to be a good predictor for bacterial adhesion compared to the radiolabeling method when good quality specific antibodies were used. This technique is convenient and allows handling of numerous samples.