Effect of Eu doping on the thermoluminescence of UV and gamma irradiated Mg2B2O5 nanophosphors

This article presents the effect of europium (Eu) doping on the thermoluminescence (TL) of ultraviolet (UV-254 nm) and gamma irradiated triclinic Mg₂B₂O₅ nanophosphors. The diffuse reflectance predicts slight decrease in band gap from 5.18 to 4.99 eV with increasing Eu (1%, 3%, and 5%) content in Mg₂B₂O₅. The TL glow curves of UV irradiated samples comprised of a main peak around 500 K with weak intensity peak/shoulders in low temperature region. Interestingly Eu (3%) doped Mg₂B₂O₅ shows maximum TL intensity with suppression of low temperature shoulder peaks and almost linear UV dose dependent TL response. However, in the case of gamma irradiated Eu (1% and 3% doped) samples, TL glow curve comprises of a main peak around 425–445 K and closely lying peak around 500–515 K with relatively lesser intensity. In case of Eu (5%) doped samples, TL peak around 508 K starts dominating over peak around 425 K. TL of both UV and gamma irradiated samples showed the presence of various deep and shallow defect states within the bandgap of materials having different kinetic parameters, which were determined using TLanal software based on Kiti's general order equation. The present study shows that Eu doped Mg₂B₂O₅ nanophosphors can be tuned for UV and gamma dosimetry.     

Luminescence study and dosimetry approach of Ce on an α‐Sr2P2O7 phosphor synthesized by a high‐temperature combustion method

We report synthesis of a cerium‐activated strontium pyrophosphate (Sr₂P₂O₇) phosphor using a high‐temperature combustion method. Samples were characterized by X‐ray diffraction (XRD), Fourier transform infrared spectroscopy (FT‐IR), photoluminescence (PL) and thermoluminescence (TL). The XRD pattern reveals that Sr₂P₂O₇ has an α‐phase with crystallization in the orthorhombic space group of Pnam. The IR spectrum of α‐Sr₂P₂O₇ displays characteristic bands at 746 and 1190 cm^‐1 corresponding to the absorption of (P₂O₇)^‐4. PL emission spectra exhibit a broad emission band around 376 nm in the near‐UV region due to the allowed 5d–4f transition of cerium and suggest its applications in a UV light‐emitting diode (LED) source. PL also reveals that the emission originates from 5d–4f transition of Ce³⁺ and intensity increases with doping concentration. TL measurements made after X‐ray irradiation, manifest a single intense glow peak at around 192°C, which suggests that this is an outstanding candidate for dosimetry applications. The kinetic parameters, activation energy and frequency factor of the glow curve were calculated using different analysis methods. Copyright © 2014 John Wiley & Sons, Ltd.     

Role of Li+ ions on the surface morphology and thermoluminescence properties of Y2O3:Tm3+ nanophosphor

Y₂O₃:Tm³⁺ and Li⁺ co‐doped Y₂O₃:Tm³⁺ nanopowders were synthesized using the solution combustion method for possible application in ultraviolet (UV) light dosimetry. X‐ray diffraction revealed the crystallite sizes to be in the range 21–44 nm and 30–121 nm using the Scherrer equation and the W‐H plot relationship, respectively. Field emission scanning electron microscopy confirmed that, after co‐doping with 4 mol% concentration of Li⁺, the particles were spherical in nature with an average size of ~30 nm. Fourier transformed infrared spectroscopy results showed bands at wavenumbers of 556, 1499, 1704, 2342, 2358, 2973, 3433, and 3610 cm^?1 that corresponded to the stretching and bending vibrations of Y–O, C=O and O–H. Thermoluminescence (TL) glow peaks for Y₂O₃:Tm³⁺ nanophosphors observed at 399 and 590 K were attributed to oxygen defects caused using UV irradiation. These oxygen defects firstly resulted in an increased prominent peak TL intensity for up to 270 min of irradiation and then a decrease. This was attributed to the presence of oxygen defect clusters that caused a reduction in recombination centres. The Li⁺ co‐doped sample showed peaks at 356, 430, and 583 K and its intensity sublinearly increased up to 90 min and then thereafter decreased. The TL trapping parameters were calculated using computerized glow curve deconvolution methods. The Li⁺ co‐doped sample exhibited less fading and high trap density under the UV radiation.     

New UVA‐emitting BaAlBO3F2:Eu2+ phosphor with PL and TL properties for phototherapy lamp

We present a new phosphor material, BaAlBO₃F₂ doped with Eu²⁺ ions, having emission in the UVA region. The phosphor material is prepared by a simple wet chemical method. Phase confirmation was carried out using the Rietveld refinement program which shows that BaAlBO₃F₂:Eu²⁺ has an hexagonal crystal system. Using a Fourier transform infrared spectroscopy graph, we studied the bond stretching present in the phosphor material. Photoluminescence (PL) characterization, carried out using a RF spectrofluorophotometer, shows two types of PL excitation and emission. Before reduction, emission is in the blue region at 431 nm; after reduction, excitation is at 258 nm and emission is at 361 nm, which is in the UVA region. Some thermoluminescence (TL) studies were carried out in this material for the first time, for example, determination of the trapping parameters, linearity, fading, glow curve convolution and deconvolution (GCCD) function for curve fitting and the T_m–T_stop method for confirmation of the trapped centers in the TL glow peak. Copyright © 2016 John Wiley & Sons, Ltd.     

Europium doped Sr2YNbO6 double perovskite phosphor for photoluminescence and thermoluminescence properties

A luminescent double perovskite phosphor Sr₂YNbO₆ doped with Eu³⁺ crystallized to the monoclinic phase and was synthesized successfully via a conventional high-temperature combustion method. The formation of the crystal structure, phase purity, and surface morphology were studied using X-ray diffraction patterns and scanning electron microscopy. The characteristic vibrations between the atoms of the functional groups present in phosphor were studied using Fourier transform infrared spectra analysis. The luminescence properties of the prepared phosphors were investigated in terms of photoluminescence (PL) and thermoluminescence (TL). PL excitation spectra exhibited charge transfer bands and the characteristic 4f⁶ transitions of Eu³⁺. A prominent PL emission was obtained for the phosphor doped with 4 mol% Eu³⁺ under the 396 nm excitation wavelength. PL emission quenching was observed for the higher doping concentrations due to a multipole–multipole interaction. A highly intense PL emission arose due to the hypersensitive ⁵D₀–⁷F₂ electric dipole transition of Eu³⁺ that dominated the emission spectra. The thermal stability of the phosphor was examined through temperature-dependent PL. The TL properties of the Sr₂YNbO₆ double perovskites irradiated with a ⁹⁰Sr beta source at different doses were measured. The double perovskite phosphors under study showed a linear dose–response with increasing beta dose, ranging from 1 Gy to 10 Gy. Trapping parameters of the TL glow curves were determined using Chen's peak shape method and computerized glow curve deconvolution (CGCD). CGCD fitting of the TL glow curves revealed that it was consisted of three major peaks and followed second-order kinetics. The estimated activation energies were determined using different methods and were comparable and significant.     

Structural characterization of Er3+,Yb3+‐doped Gd2O3 phosphor,synthesized using the solid‐state reaction method,and its luminescence behavior

We report the synthesis and structural characterization of Er³⁺,Yb³⁺‐doped Gd₂O₃ phosphor. The sample was prepared using the conventional solid‐state reaction method, which is the most suitable method for large‐scale production. The prepared phosphor sample was characterized using X‐ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), Fourier transform infrared spectroscopy (FTIR), thermoluminescence (TL), photoluminescence (PL) and CIE techniques. For PL studies, the excitation and emission spectra of Gd₂O₃ phosphor doped with Er³⁺ and Yb³⁺ were recorded. The excitation spectrum was recorded at a wavelength of 551 nm and showed an intense peak at 276 nm. The emission spectrum was recorded at 276 nm excitation and showed peaks in all blue, green and red regions, which indicate that the prepared phosphor may act as a single host for white light‐emitting diode (WLED) applications, as verified by International de I'Eclairage (CIE) techniques. From the XRD data, the calculated average crystallite size of Er³⁺ and Yb³⁺‐doped Gd₂O₃ phosphor is ~ 38 nm. A TL study was carried out for the phosphor using UV irradiation. The TL glow curve was recorded for UV, beta and gamma irradiations, and the kinetic parameters were also calculated. In addition, the trap parameters of the prepared phosphor were also studied using computerized glow curve deconvolution (CGCD). Copyright © 2015 John Wiley & Sons, Ltd.     

Thermoluminescence dosimeter (TLD) studies of Ca10K(PO4)7:Dy phosphor for applications in radiation dosimetry

This study reports the thermoluminescence (TL) aspects of Ca₁₀K(PO₄)₇:Dy phosphor synthesized using a wet chemical method for the first time. The X-ray diffraction (XRD) results confirm the formation of the desired crystalline phase. Surface morphological studies reveal the formation of polyhedrons and agglomerations having an average diameter of 200 nm, while energy dispersive X-ray spectroscopy (EDS) data show the presence and composition of the elements in appropriate amounts. The effect of Dy doping concentration has been studied on the TL properties with exposure to gamma radiations from the Co-60 source. The best TL response has been observed for 5 mol% Dy doping concentration. The glow curve is simple and consists of a single peak at 130°C. The effect of the heating rate has been studied on the TL glow curve, and the heating rate of 5°C/s shows the best TL response. The various TL properties such as annealing conditions, dose–response, TL linearity, fading, and reusability of the prepared phosphor have been studied to check its suitability as a good TL dosimeter (TLD). TL characterization of the phosphor reports that the TL response is linear from 5- to 2000 Gy. The results show that this phosphor can be a good TLD for the dosimetry of gamma radiations from Co-60.     

Natural dead sea salt and retrospective dosimetry

Accidents resulting in widespread dispersal of radioactive materials have given rise to a need for materials that are convenient in allowing individual dose assessment. The present study examines natural Dead Sea salt adopted as a model thermoluminescence dosimetry system. Samples were prepared in two different forms, loose-raw and loose-ground, subsequently exposed to ⁶⁰Co gamma-rays, delivering doses in the range 2–10 Gy. Key thermoluminescence (TL) properties were examined, including glow curves, dose response, sensitivity, reproducibility and fading. Glow curves shapes were found to be independent of given dose, prominent TL peaks for the raw and ground samples appearing in the temperature ranges 361–385 ºC and 366–401 ºC, respectively. The deconvolution of glow curves has been undertaken using GlowFit, resulting in ten overlapping first-order kinetic glow peaks. For both sample forms, the integrated TL yield displays linearity of response with dose, the loose-raw salt showing some 2.5 × the sensitivity of the ground salt. The samples showed similar degrees of fading, with respective residual signals 28 days post-irradiation of 66% and 62% for the ground and raw forms respectively; conversely, confronted by light-induced fading the respective signal losses were 62% and 80%. The effective atomic number of the Dead Sea salt of 16.3 is comparable to that of TLD-200 (Z_eff 16.3), suitable as an environmental radiation monitor in accident situations but requiring careful calibration in the reconstruction of soft tissue dose (soft tissue Z_eff 7.2). Sample luminescence studies were carried out via Raman and Photoluminescence spectroscopy as well as X-ray diffraction, ionizing radiation dependent variation in lattice structure being found to influence TL response.

     

Luminescence investigation of CaY2Al4SiO12:Dy3+ phosphor synthesized by sol–gel method

Dy³⁺-doped CaY₂Al₄SiO₁₂ phosphors were prepared using the sol–gel method. X-ray diffraction (XRD), field emission scanning electron microscopy (FESEM), and energy dispersive spectroscopy analyses (EDS) were used to analyse the crystal structure, morphology, and elemental composition of the prepared samples. The luminescence behaviour of the sample was investigated using photoluminescence (PL) and thermoluminescence (TL) techniques. The prepared CaY₂Al₄SiO₁₂:xDy³⁺ phosphor showed a characteristic blue and yellow emission at ~480 and 583 nm, respectively, with an excitation wavelength of 350 nm. The most intense PL emission was found for a 4 mol% doping concentration of Dy³⁺ ions. The CIE diagram of the phosphor showed bluish-white colour emission. For TL studies, the prepared phosphors were irradiated with a ⁶⁰Co γ (gamma) source and the TL glow curve of the CaY₂Al₄SiO₁₂:0.04Dy³⁺ phosphor showed three overlapped peaks. For the Gaussian peaks, Chen's peak shape method was applied to determine the kinetic parameters of the samples.     

Ca2Al2SiO7:Ce3+ phosphors for mechanoluminescence dosimetry

A series of Ce³⁺ ion single‐doped Ca₂Al₂SiO₇ phosphors was synthesized by a combustion‐assisted method at an initiating temperature of 600 °C. The samples were annealed at 1100 °C for 3 h and their X‐ray diffraction patterns confirmed a tetragonal structure. The phase structure, particle size, surface morphology and elemental analysis were analyzed using X‐ray diffraction (XRD), transmission electron microscope (TEM), scanning electron microscopy (SEM) and energy dispersive X‐ray (EDX) spectroscopy techniques. Thermoluminescence (TL) intensity increased with increase in ultraviolet (UV) light exposure time up to 15 min. With further increase in the UV irradiation time the TL intensity decreases. The increase in TL intensity indicates that trap concentration increased with UV exposure time. A broad peak at 121 °C suggested the existence of a trapping level. The peak of mechanoluminescence (ML) intensity versus time curve increased linearly with increasing impact velocity of the moving piston. Mechanoluminescence intensity increased with increase in UV irradiation time up to 15 min. Under UV‐irradiation excitation, the TL and ML emission spectra of Ca₂Al₂SiO₇:Ce³⁺ phosphor showed the characteristic emission of Ce³⁺ peaking at 400 nm (UV–violet) and originating from the Ce³⁺ transitions of 5d‐4f (²F_5/2 and ²F_7/2). The photoluminescence (PL) emission spectra for Ca₂Al₂SiO₇:Ce³⁺ were similar to the ML/TL emission spectra. The mechanism of ML excitation and the suitability of the Ca₂Al₂SiO₇:Ce³⁺phosphor for radiation dosimetry are discussed. Copyright © 2016 John Wiley & Sons, Ltd.     

Luminescence properties of Ce-doped ZrO2 phosphors synthesized by combustion method

Zr_1−xCe_xO₂ with x = 0.005, 0.01, 0.02, and 0.03 samples were synthesized using a combustion technique. The X-ray diffraction results revealed that Ce-doped ZrO₂ nanoparticles were in a monoclinic structure up to 1 mol% Ce concentration. The increase in the Ce concentration caused more distortion in the monoclinic structure of zirconia. The samples showed a mixed phase (monoclinic + tetragonal) beyond 1 mol% Ce content. The crystallite size (D) and strain (ε) were calculated from the Williamson–Hall equation. The D decreased from 25 ± 1 to 20 ± 1 nm and ε increased from 0.03 to 0.28% with an increase in Ce concentration. Photoluminescence (PL) spectra of Zr_1−xCe_xO₂ showed emission in the blue region under an excitation wavelength of 290 nm. Zr_0.995Ce_0.005O₂ showed the highest PL intensity with an average lifetime of 0.93 μs, and the PL intensity decreased with the increase in the Ce concentration. Thermoluminescence (TL) glow curves of Zr_1−xCe_xO₂ were measured after gamma irradiation (500 Gy) with a heating rate of 5 K s⁻¹. The TL curve of Zr_0.995Ce_0.005O₂ showed two prominent peaks at 412 K (peak 1) and 600 K (peak 2). The first TL glow peak was shifted towards a higher temperature at 440 K above 1 mol% Ce concentration. Repetitive TL measurements on the same aliquot exhibited excellent repeatability. Kinetic parameters associated with the TL peaks were calculated using the curve fitting method. Peak 1 followed non-first-order kinetics. The value of the activation energy of the 440 K peak was found to be 0.95 ± 0.01 eV for Zr_0.99Ce_0.01O₂. These findings showed that Zr_1−xCe_xO₂ might be used in lighting and radiation dosimeter applications.     

Luminescence study of LiMgBO3:Dy for γ‐ray and carbon ion beam exposure

LiMgBO₃:Dy³⁺, a low Z_eff material was prepared using the solution combustion method and its luminescence properties were studied using X‐ray diffraction (XRD), scanning electron microscopy (SEM), thermoluminescence (TL), photoluminescence (PL), Fourier transform infrared spectroscopy, and electron paramagnetic resonance (EPR) techniques. Reitvield refinement was also performed for the structural studies. The PL emission spectra for LiMgBO₃:Dy³⁺ consisted of two peaks at 478 due to the ⁴F_9/2→⁶H_15/2 magnetic dipole transition and at 572 nm due to the hypersensitive ⁴F_9/2→⁶H_13/2 electric dipole transition of Dy³⁺, respectively. A TL study was carried out for both the γ‐ray‐irradiated sample and the C⁵⁺ irradiated samples and was found to show high sensitivity for both. Moreover the γ‐ray‐irradiated LiMgBO₃:Dy³⁺ sample showed linearity in the dose range 10 Gy to 1 kGy and C⁵⁺‐irradiated samples show linearity in the fluence range 2 × 10¹⁰ to 1 × 10¹¹ ions/cm². In the present study, the initial rise method, various heating rate method, the whole glow curve method, glow curve convolution deconvolution function, and Chen's peak shape method were used to calculate kinetic parameters to understand the TL glow curve mechanism in detail. Finally, an EPR study was performed to examine the radicals responsible for the TL process.     

Luminescence properties of nanocrystalline Mg2P2O7:Eu phosphor

Thermoluminescence (TL) measurements were carried out on europium (Eu) doped magnesium pyrophosphate (Mg₂P₂O₇) nanopowders using gamma irradiation in the dose range of 0.1 to 3 kGy. The powder samples were successfully synthesized by chemical co‐precipitation synthesis route. The formation and crystallinity of the compound was confirmed by powder X‐ray diffraction (PXRD) pattern. The estimated particle size was found to be in nanometer scale by using Debye Scherer's formula. A scanning electron microscopy (SEM) study was carried out for the morphological characteristics of as synthesized Mg₂P₂O₇:Eu phosphor. Photoluminescence (PL) study was carried out to confirm the presence of the rare‐earth ion and its valence state. The TL analysis of synthesized samples were performed after the irradiation of Mg₂P₂O₇:Eu with cobalt‐60 (⁶⁰Co) gamma rays. The high and low intensity peaks of TL glow curve appeared at around 400 K, 450 K, 500 K and 596 K respectively. The appreciable shift in peak positions has been observed for different concentrations of Eu ion. The trapping parameters, namely activation energy (E), order of kinetics (b) and frequency factor (s) have been determined using thermal cleaning process, peak shape (Chen's) method and glow curve deconvolution (GCD) functions.     

Thermoluminescence emission on lead oxychloroborate glasses under UV exposure

Glassy materials were prepared using two different systems: 50B₂O₃ – (50 ? x)PbO ? xPbCl_2, with x = 0, 2 and 5 in mol % (System BPCl‐I) and 50BO_1.5 – (50 ? x)PbO ? xPbCl₂ with x = 0, 2, 5 and 7 in cationic % (System BPCl‐II). Structural and optical characterization showed that PbCl when substituted for PbO changed the structure of the glass network by replacing nonbridging oxygens for chlorine ions. This substitution also caused a change in the number of defects responsible for thermoluminescence (TL) emission (electrons and hole trap centres). Thermoluminescence emissions were observed for the first time in lead oxychloroborate glasses after exposure to UV radiation. Sample BPCl‐I‐2 (x = 2 from System I) demonstrated better TL emission compared with other glass samples. One intense peak in the glow curve, centred at ~122°C followed by a shoulder at ~180°C, was highly sensitive to UV radiation. There were also good linear responses at dose range ~0.4 to ~2 J/cm² for the first peak (low temperature) and ~0.4 to ~4 J/cm² for the second peak (high temperature).     

Evaluation of trapping parameters of γ‐rays irradiated Dy3+‐doped LaPO4 phosphors

Thermoluminescence (TL) materials are widely used in radiation measurements. The best‐known applications of TL materials are in the dosimetry of ionizing radiation, and in CTV screen phosphors, scintillators, X‐ray laser materials, etc. The TL glow curve and its kinetic parameters for annealed LaPO₄ at different constant temperatures and for Dy³⁺‐doped LaPO₄ phosphors irradiated by gamma‐rays are reported here. The samples were irradiated using a ⁶⁰Co gamma‐ray source at a dose of 10 Gy and the heating rate used for TL measurements was 5ºC/s. The samples were characterized using X‐ray diffraction (XRD), Fourier transform infrared, transmission electron microscopy and TL techniques. The XRD pattern shows that the prepared phosphor has a good crystalline structure with an average crystallite size of ~ 18 nm. The samples show good TL peaks for 0.05, 0.1 and 0.2 mole % doping concentrations of Dy³⁺ ions and anneal above 400ºC. The TL glow curve characteristics of annealed LaPO₄ and Dy³⁺‐doped LaPO₄ were analyzed and trapping parameters calculated using various methods. All TL glow curves obey the second‐order kinetics with a single glow peak, which reveals that only one set of trapping parameter is set for a particular temperature. The TL sensitivity was found to depend upon the annealing temperature and Dy³⁺ doping concentration. The prepared sample may be a new nano phosphor and be useful in TL dosimetry. Copyright © 2014 John Wiley & Sons, Ltd.     

Mechanoluminescence,thermoluminescence, photoluminescence studies on Ca3Y2Si3O12:RE3+ (RE3+ = Dy3+and Eu3+) phosphors

Dy³⁺ and Eu³⁺ activated Ca₃Y₂Si₃O₁₂ phosphors were synthesized by the solid‐state synthesis method. The phosphors were characterized by X‐ray diffraction (XRD), mechanoluminescence (ML), thermoluminescence (TL) and photoluminescence (PL) to determine structure and luminescence. For ML glow curves, only one peak was observed, as only one type of luminescence centre was formed during irradiation. The Ca₃Y₂Si₃O₁₂:Dy³⁺ TL glow curve showed a single peak at 151.55°C and the Ca₃Y₂Si₃O₁₂:Eu³⁺ TL glow curve peaked at 323°C with a small peak at 192°C, indicating that two types of traps were activated. The trapping parameters for both the samples were calculated using Chen's peak shape method. Dy³⁺‐activated Ca₃Y₂Si₃O₁₂ showed emission at 482 and 574 nm when excited by a 351 nm excitation wavelength, whereas the Eu³⁺‐activated Ca₃Y₂Si₃O₁₂ phosphor PL emission spectra showed emission peaks at 613 nm, 591 nm, 580 nm when excited at 395 nm wavelength. When excited at 466 nm, prominent emission peaks were observed at their respective positions with very slight shifts. Copyright © 2015 John Wiley & Sons, Ltd.     

Thermoluminescence characterization of Ag‐doped Li2B4O7 single crystal materials

In this study, the thermoluminescence (TL) characteristics of Ag‐doped and undoped lithium tetraborate (Li₂B₄O₇, LTB) materials, grown using the Czochralski method, were reported. The TL properties of LTB:Ag, such as glow curve structure, dose response, fading and reproducibility, were investigated. The glow curve of the Li₂B₄O₇:Ag single crystal consists of four peaks located at approximately 75, 130, 190 and 275°C; in undoped LTB, the single crystal shows a broad glow curve with peaks at 65, 90, 125, 160 and 190°C using a heating rate of 5°C/s in the 50–350°C temperature region. The high temperature peak of Ag‐doped sample at 275°C has a nonlinear dose response within the range from 33 mGy to 9 Gy. There is a linear response in the range of 33–800 mGy; after which, a sublinear region appears up to 9 Gy for Ag‐doped LTB single crystal. For undoped single crystal, the dose response is supralinear for low doses and linear for the region between 1 and 9 Gy. The thermal fading ratio of the undoped material is almost 60% for the high temperature peak after 7 days. Ag‐doped LTB single crystal exhibits different behaviour over a period of 7 days.     

Thermoluminescence properties of gamma‐irradiated nano‐structure hydroxyapatite

The suitability of nano‐structured hydroxyapatite (HAP) for use as a thermoluminescence dosimeter was investigated. HAP samples were synthesized using a hydrolysis method. The formation of nanoparticles was confirmed by X‐ray diffraction and average particle size was estimated to be ~30 nm. The glow curve exhibited a peak centered at around 200 °C. The additive dose method was applied and this showed that the thermoluminescence (TL) glow curves follow first‐order kinetics due to the non‐shifting nature of T_m after different doses. The numbers of overlapping peaks and related kinetic parameters were identified from T_m–T_stop through computerized glow curve deconvolution methods. The dependence of the TL responses on radiation dose was studied and a linear dose response up to 1000 Gy was observed for the samples. Copyright © 2015 John Wiley & Sons, Ltd.     

Thermoluminescence study of the in vivo effects of bicarbonate depletion and acetate/formate presence in the two algae Chlamydobotrys stellata and Chlamydomonas reinhardtii

We investigated the influence of CO₂/HCO₃ ^–-depletion and of the presence of acetate and formate on the in vivo photosynthetic electron transport in the two green algae Chlamydobotrys stellata and Chlamydomonas reinhardtii by means of thermoluminescence technique and mathematical glow curve analysis. The main effects of the removal of CO₂ from the algal cultures was: (1) A shift of the glow curve peak position to lower temperatures resulting from a decrease of the B band and an increase of the Q band. (2) Treatment of CO₂-deficient Chl. stellata with DCMU yielded two thermoluminescence bands in the Q band region peaking at around +12°C and +5°C; in case of Chl. reinhardtii DCMU treatment induced only one band with an emission maximum at +5°C. The presence of acetate or formate in CO₂-depleted algal cultures lowered the intensities of all of the individual TL bands but that of a HT band (TL+37). The effects of CO₂-depletion and of the presence of anions were fully reversible.Abbreviations DCMU 3-(3,4)-dichlorophenyl-1,1-dimethylurea - HT band high temperature TL band - P₆₈₀ reaction center chlorophyll of PS II - Q_A and Q_B primary and secondary quinone acceptors of PS II, respectively - PS II Photosystem II - S_2/3 redox states of the oxygen evolving complex of PS II - TL thermoluminescence     

Intense green light emission and thermoluminescence glow curve analysis of Tb3+-activated CaY2O4 phosphor

Here, the synthesis and luminescence analysis of the Tb³⁺-activated phosphor were reported. The CaY₂O₄ phosphors were synthesized using a modified solid-state reaction method with a variable doping concentration of Tb³⁺ ion (0.1–2.5 mol%). As synthesized, the phosphor was characterized using Fourier transform infrared spectroscopy (FTIR) and X-ray diffraction analysis techniques for the optimized concentration of doping ions. The prepared phosphor showed a cubic structure, and FTIR analysis confirmed functional group analysis. It was discovered that the intensity of 1.5 mol% was higher than at other concentrations after the photoluminescence (PL) excitation and emission spectra were recorded for different concentrations of doping ions. The excitation was monitored at 542 nm, and the emission was monitored at 237 nm. At 237 nm excitation, the emission peaks were found at 620 nm (⁵D₄→⁷F₃), 582 nm (⁵D₄→⁷F₄), 542 nm (⁵D₄→⁷F₅), and 484 nm (⁵D₄→⁷F₆). The 1931 CIE (x, y) chromaticity coordinates showed the distribution of the spectral region calculated from the PL emission spectra. The values of (x = 0.34 and y = 0.60) were very close to dark green emission. Therefore, the produced phosphor would be very useful for light-emitting diode (green component) applications. Thermoluminescence glow curve analysis for various concentrations of doping ions and various ultraviolet (UV) exposure times was carried out, and a single broad peak was found at 252°C. The computerized glow curve deconvolution method was used to obtain the related kinetic parameters. The prepared phosphor exhibited an excellent response to UV dose and could be useful for UV ray dosimetry.