A low power DC/DC booster circuit designed for microbial fuel cells

A DC/DC booster circuit was fabricated and tested for use with microbial fuel cells (MFCs) to increase the typical operational voltage (100–300 mV) to a maximum power of >3 V. In steady state, the low power DC/DC voltage booster circuit was sustainable, i.e., powered by the MFCs alone, but required an external power source to start (but not needed to maintain) the oscillator. The operating principle and function of each part of the circuit is described. A procedure for determining the optimal set of values for each component in the circuit was established. The performance of the circuit was demonstrated using three Shewanella oneidensis MR-1 based MFCs connected in parallel. The power consumption of the booster circuit was less than 20 μW, which was less than the output from the three MFCs. After the output capacitor was charged to 5 V, the booster circuit can be powered by the MFCs alone. Under normal operation, the MFCs were able to power the booster circuit and a light emitting diode.     

Construction of d-amino acid biosensor based on d-amino acid oxidase immobilized onto poly (indole-5-carboxylic acid)/zinc sulfide nanoparticles hybrid film

d-Amino acid oxidase (DAAO) purified from goat kidney was immobilized covalently via N-ethyl-N-(3-dimethylaminopropyl) carbodiimide (EDC) and N-hydroxy succinimide (NHS) chemistry onto poly indole 5-carboxylic acid (Pin5-COOH)/zinc sulfide nanoparticles (ZnSNPs) hybrid film electrodeposited on surface of an Au electrode. A highly sensitive d-amino acid biosensor was constructed using this enzyme electrode as working electrode, Ag/AgCl as reference electrode, and Pt wire as auxiliary electrode connected through potentiostat. The biosensor showed optimum response within 3 s at pH 7.5 and 35 °C, when polarized at 0.15 V vs. Ag/AgCl. There was a linear relationship between biosensor response (mA) and d-alanine concentration in the range 0.001–2.0 mM. The sensitivity of the biosensor was 58.85 μA cm^?2 mM^?1 with a detection limit of 0.001 mM (S/N = 3). The enzyme electrode was used 120 times over a period of 2 months when stored at 4 °C. The biosensor has an advantage over earlier enzyme sensors that it has no leakage of enzyme during reuse and is unaffected by the external environment due to the protective layer of poly indole-5-carboxylic acid film. The biosensor was evaluated and employed for measurement of d-amino acid level in fruits and vegetables.     

Immobilization of lysine oxidase on a gold–platinum nanoparticles modified Au electrode for detection of lysine

A commercial lysine oxidase (LyOx) from Trichoderma viride was immobilized covalently onto gold nanoparticles (AuNPs) and platinum nanoparticles (PtNPs) electrodeposited onto Au electrode using 3-aminopropyltriethoxy silane (3-APTES) and glutaraldehyde cross linking chemistry. A lysine biosensor was fabricated using LyOx/3-APTES/AuNPs-PtNPs/Au electrode as a working electrode, Ag/AgCl (3 M KCl) as standard electrode and Pt wire as auxiliary electrode connected through a potentiostat. The enzyme electrode was characterized by scanning electron microscopy (SEM), Fourier transform infrared (FTIR) spectroscopy, electrochemical impedance spectroscopy (EIS) and cyclic voltammetry (CV). The cumulative effect of AuNPs and PtNPs showed excellent electrocatalytic activity at low applied potential for detection of H₂O₂, a product of LyOx reaction. The sensor showed its optimum response within 4 s, when polarized at 0.2 V vs. Ag/AgCl in 0.1 M phosphate buffer, pH 7.5 at 30 °C. The linear range and detection limit of the sensor were 1.0–600 μM and 1.0 μM (S/N = 3), respectively. Biosensor measured lysine level in sera, milk and amino acid tablet, which correlated well with those by standard HPLC method. The enzyme electrode lost 50% of its initial activity after 200 uses over a period of 4 months.     

Towards a hybrid anaerobic digester-microbial fuel cell integrated energy recovery system: An overview of the development of an electrogenic biofilm

An electrogenic biofilm was developed on a macroporous chitosan-carbon nanotube (CHIT-CNT) electrode under constant poised potential (?0.25 V versus Ag/AgCl reference electrode) and flow through conditions utilizing the effluent of an anaerobic digester as both the inoculant and substrate for the electrogenic biofilm. After 125 days of inoculation the bioelectrode demonstrated an open circuit potential of ?0.62 V and a current density of 9.43 μA cm^?3 (at ?0.25 V). Scanning electron microscopy images indicate thorough surface coverage of the biofilm with a high density of bacterial nanowires physically connecting bacteria to bacteria and bacteria to carbon nanotube (electrode surface) suggesting the nanowires are electrically conductive. DGGE was used to identify the major bacterial and archaeal populations.     

Electrochemical analysis of autodisplayed adrenodoxin (Adx) on the outer membrane of E. coli

In this work, adrenodoxin (Adx) was expressed on the outer membrane of E. coli by autodisplay and then the iron–sulfur cluster was incorporated into apo-Adx by an anaerobic reconstitution process. For the determination of the redox potentials of the iron–sulfur clusters of the autodisplayed Adx, E. coli cells with autodisplayed Adx were immobilized on a gold electrode modified with a self-assembled monolayer of mercaptoundecanoic acid (MUA). From the repeated cyclic voltammetry (CV) analysis, the E. coli (10 mM HEPES buffer, pH 7.0) with autodisplayed Adx showed significant changes in shape with an oxidation peak at + 0.4 V (vs. Ag/AgCl) and a reduction peak at − 0.3 V (vs. Ag/AgCl) after the reconstitution process for the incorporation of the iron–sulfur cluster. From the repeated CV analysis in the reduction and oxidation potential ranges, the iron–sulfur clusters of the autodisplayed Adx were observed to undergo reversible redox reactions via direct electron transfer to the MUA-modified gold electrode.     

A method for determination of xanthine in meat by amperometric biosensor based on silver nanoparticles/cysteine modified Au electrode

A method is described for construction of an amperometric xanthine biosensor based on covalent Immobilization of xanthine oxidase (XOD) onto citrate capped silver nanoparticles deposited on Au electrode surface through cysteine self assembled monolayers (SAM). The biosensor showed optimum response within 5 s at pH 7.0 and 35 °C, when polarized at 0.5 V vs. Ag/AgCl. The linear working range of biosensor for xanthine was from 2 to 16 μM, with a detection limit of 0.15 μM and sensitivity of 0.17 mA/μM/cm². The mean analytical recovery of exogenously added xanthine in fish meat extract (5 g/l and 10 g/l) was 96.2 ± 2.3% and 95.2 ± 3.4%, respectively. Within and between batches coefficients of variation were <2.6% and <3.4%, respectively. The biosensor measured xanthine in fish, chicken, pork, and beef meat. The enzyme electrode lost 20% of its initial activity after its regular 180 uses over a period of 60 days, when stored at 4 °C in dry state.     

Weak electric fields serve as guidance cues that direct retinal ganglion cell axons in vitro

Growing axons are directed by an extracellular electric field in a process known as galvanotropism. The electric field is a predominant guidance cue directing retinal ganglion cell (RGC) axons to the future optic disc during embryonic development. Specifically, the axons of newborn RGCs grow along the extracellular voltage gradient that exists endogenously in the embryonic retina (Yamashita, 2013 [8]). To investigate the molecular mechanisms underlying galvanotropic behaviour, the quantification of the electric effect on axon orientation must be examined. In the present study, a culture system was built to apply a constant, uniform direct current (DC) electric field by supplying an electrical current to the culture medium, and this system also continuously recorded the voltage difference between the two points in the medium. A negative feedback circuit was designed to regulate the supplied current to maintain the voltage difference at the desired value. A chick embryo retinal strip was placed between the two points and cultured for 24 h in an electric field in the opposite direction to the endogenous field, and growing axons were fluorescently labelled for live cell imaging (calcein-AM). The strength of the exogenous field varied from 0.0005 mV/mm to 10.0 mV/mm. The results showed that RGC axons grew in the reverse direction towards the cathode at voltage gradients of ≥0.0005 mV/mm, and straightforward extensions were found in fields of ≥0.2–0.5 mV/mm, which were far weaker than the endogenous voltage gradient (15 mV/mm). These findings suggest that the endogenous electric field is sufficient to guide RGC axons in vivo.     

Cell proliferation and survival in the mating circuit of adult male hamsters: Effects of testosterone and sexual behavior

The transient actions of gonadal steroids on the adult brain facilitate social behaviors, including reproduction. In male rodents, testosterone acts in the posterior medial amygdala (MeP) and medial preoptic area (MPOA) to promote mating. Adult neurogenesis occurs in both regions. The current study determined if testosterone and/or sexual behavior promote cell proliferation and survival in MeP and MPOA. Two experiments were conducted using the thymidine analog BrdU. First, gonad-intact and castrated male hamsters (n = 6/group) were compared 24 h or 7 weeks after BrdU. In MeP, testosterone-stimulated cell proliferation 24 h after BrdU (intact: 22.8 ± 3.9 cells/mm², castrate: 13.2 ± 1.4 cells/mm²). Testosterone did not promote cell proliferation in MPOA. Seven weeks after BrdU, cell survival was sparse in both regions (MeP: 2.5 ± 0.6 and MPOA: 1.7 ± 0.2 cells/mm²), and was not enhanced by testosterone. In Experiment 2, gonad-intact sexually-experienced animals were mated weekly to determine if regular neural activation enhances cell survival 7 weeks after BrdU in MeP and MPOA. Weekly mating failed to increase cell survival in MeP (8.1 ± 1.6 vs. 9.9 ± 3.2 cells/mm²) or MPOA (3.9 ± 0.7 vs. 3.4 ± 0.3 cells/mm²). Furthermore, mating at the time of BrdU injection did not stimulate cell proliferation in MeP (8.9 ± 1.7 vs. 8.1 ± 1.6 cells/mm²) or MPOA (3.6 ± 0.5 vs. 3.9 ± 0.7 cells/mm²). Taken together, our results demonstrate a limited capacity for neurogenesis in the mating circuitry. Specifically, cell proliferation in MeP and MPOA are differentially influenced by testosterone, and the birth and survival of new cells in either region are not enhanced by reproductive activity.     

Granular activated carbon single-chamber microbial fuel cells (GAC-SCMFCs): A design suitable for large-scale wastewater treatment processes

As an emerging biotechnology capable of removing contaminants and producing electricity, microbial fuel cells (MFCs) hold a promising future in wastewater treatment. However, several main problems, including the high internal resistance (R_in), low power output, expensive material, and complicated configuration have severely hindered the large-scale application of MFCs. The study targeted these challenges by developing a novel MFC system, granular activated carbon single-chamber MFC, termed as GAC-SCMFC. The batch tests showed that GAC was a good substitute for carbon cloth and GAC-SCMFCs generated high and stable power outputs compared with the traditional two-chamber MFCs (2CMFCs). Critical operational parameters (i.e. wastewater substrate concentrations, GAC amount, electrode distance) affecting the performance of GAC-SCMFCs were examined at different levels. The results showed that the R_in gradually decreased from 60 Ω to 45 Ω and the power output increased from 0.2 W/m³ to 1.2 W/m³ when the substrate concentrations increased from 100 mg/L to 850 mg/L. However, at high concentrations of 1000–1500 mg/L, the power output leveled off. The R_in of MFCs decreased 50% when the electrode distance was reduced from 7.5 cm to 1 cm. The highest power was achieved at the electrode distance of 2 cm. The power generation increased with more GAC being added in MFCs due to the higher amount of biomass attached. Finally, the multi-anode GAC-SCMFCs were developed to effectively collect the electrons generated in the GAC bed. The results showed that the current was split among the multiple anodes, and the cathode was the limiting factor in the power production of GAC-SCMFCs.     

Osteocalcin Levels on Oral Glucose Load in Women being Investigated for Polycystic Ovary Syndrome

ObjectiveOsteocalcin (OC) might play a hormone-like role in energy metabolism and the regulatory circuit between the pancreas and osteoblasts. Effects of a 75-g oral glucose tolerance test (OGTT) on total OC, undercarboxylated (ucOC), and carboxylated osteocalcin (cOC) in insulin-resistant (IR) and noninsulin-resistant (nIR) premenopausal women was evaluated, and the relationships of changes in OC, ucOC, and cOC with area under the curve (AUC) insulin and the Matsuda index were examined.MethodsIn this cross-sectional study, 105 premenopausal women underwent OGTT; 18 were IR (homeostatic model assessment of insulin resistance [HOMA-IR] > 2.6; (2 with type 2 diabetes, 2 with impaired glucose tolerance), and 87 were nIR (3 with impaired glucose tolerance). Changes in total OC, ucOC, and cOC were evaluated 60 and 120 minutes after glucose loading.ResultsAt baseline, IR subjects had significantly lower levels of total OC, cOC, and ucOC. In nIR women, total OC decreased by 19% from 18.0 ng/mL (14.5-24.7) at baseline to 14.6 ng/mL (10.9-17.8) after 120 minutes, ucOC decreased by 22% from 3.2 ng/mL (2.1-4.5) to 2.5 ng/mL (1.7-3.5), and cOC decreased by 26% from 14.9 ng/mL (12.1-20.4) to 11.1 ng/mL (9.0-14.5) (P < .001, respectively). No significant decreases were noted in IR subjects. The declines in OC and cOC predicted AUCinsulin (ΔOC: β = 0.301, P = .001; ΔcOC: β = 0.315, P < .001) and the Matsuda index (ΔOC: β = − 0.235, P = .003; ΔcOC: β = − 0.245, P = .002).ConclusionsGlucose intake lowers levels of OC, ucOC, and cOC in nIR women, the extent of which predicts IR and insulin sensitivity in premenopausal women. OC parameters seem suppressed in IR women. There might be a differential osteoblast response to oral glucose in IR and nIR women, with OC reflecting this finding. (Endocr Pract. 2014;20:5-14)     

Uncertainties in the identification of potential dispersal corridors: The importance of behaviour,sex, and algorithm

Modelling landscape connectivity represents one of the central challenges for conservation of natural resources, especially in human dominated landscapes. Many different methods have been developed to this effect, but their assumptions and limitations have been largely ignored. Using high resolution GPS tracking data from brown bears (Ursus arctos) in central Italy, we investigated the influence of behavioural state (movement vs other behaviours), sex, and algorithms, namely least cost path and circuit theory, on the identification of structural corridors. In particular, considering that most studies does not account for behavioural states and/or individual characteristics, and that basically all studies consider only a single corridor algorithm, we performed (1) a within-algorithm comparison, under the hypothesis that both behavioural states and sex would influence prediction of structural corridors, and (2) a between-algorithm comparison, under the hypothesis that different algorithms would predict different corridors. We found that the impact of sex and/or behavioural state was substantial. On average, least cost path corridors for moving females were 4.7 km apart (st.dev = 7.6 km) from corridors for moving males, and 5.0 km apart (st.dev = 7.2 km) from corridors not considering sex and behaviour. The same was true for circuit theory corridors. The between-algorithm comparison showed that the two corridor models yielded almost identical results, with >80% of the least cost path corridors falling into the two top deciles for the corresponding circuit theory corridors.Our results suggest that the failure to consider an animal’s behavioural state and/or intraspecific differences may result in misidentification of corridors, with potential misallocation of the limited conservation resources available.     

The effect of internal capacitance on power quality and energy efficiency in a tubular microbial fuel cell

The pseudo-capacitive behaviour of a high surface area carbon veil electrode in a tubular microbial fuel cell (MFC) was investigated as a mechanism to enhance power quality and energy efficiency. Accumulated charge and energy from the anodic biofilm after prolonged open circuit times (1–120 min) were compared against equivalent periods of steady state loading (R = 100–3000 Ω). A significant difference in the amount of accumulated charge with different loads was observed, resulting in 1.051 C (R = 100 Ω) compared to 0.006 C (R = 3 kΩ). The automated application of short open and closed circuit (0.5–10 s) cycles resulted in an increase of power/current production (closed circuit alone), but presented lower efficiency considering entire open and closed period. The cumulative charge on the carbon veil electrode with biofilm was 39,807 C m⁻² at 100 Ω. Electrochemical Impedance Spectroscopy (EIS) showed that the Helmholtz layer presented a double layer capacitance of more than ten times the biofilm on electrode. The results indicate that the capacitive behaviour could be utilized to increase the power quality, i.e. its availability/applicability with respect to the operation of low power consuming devices.     

Electrochemical detection of xanthine in fish meat by xanthine oxidase immobilized on carboxylated multiwalled carbon nanotubes/polyaniline composite film

A commercial xanthine oxidase (XOD) was immobilized covalently onto carboxylated multiwalled carbon nanotubes (c-MWCNT) and polyaniline (PANI) composite film electrodeposited on the surface of a Pt electrode, using N-ethyl-N′-(3-dimethyl aminopropyl) carbodiimide (EDC) and N-hydroxy succinimide (NHS) chemistry. A xanthine biosensor was fabricated using XOD/c-MWCNT/PANI/Pt electrode as a working electrode, Ag/AgCl (3 M KCl) as standard electrode and Pt wire as auxiliary electrode connected through a potentiostat. The enzyme electrode was characterized by scanning electron microscopy (SEM) and Fourier transform infrared (FTIR) spectrophotometry and electrochemical impedance spectroscopy (EIS). The biosensor showed optimum response within 4 s at pH 7.0 and 35 °C, when polarized at 0.4 V. The optimized xanthine biosensor showed linear response range of 0.6–58 μM, with a detection limit of 0.6 μM (S/N = 3), and a correlation coefficient of 0.98. The biosensor was applied to determine xanthine in fish meat. The biosensor lost 50% of its initial activity after its 200 uses over a period of 100 days.     

Simultaneous nitrogen and carbon removal in a single chamber microbial fuel cell with a rotating biocathode

In this study, a single chamber microbial fuel cell (MFC) with a rotating biocathode is developed to simultaneously remove chemical oxygen demand (COD) and nitrogen accompanying current production. Under continuous regime with a feeding COD/N ratio of 5:1, removal efficiencies of total organic carbon (TOC) and total nitrogen (TN) were 85.7 ± 7.4% and 91.5 ± 7.2%, respectively, and a maximum power output of 585 mW m^?3 was yielded. In the batch tests, TN removal efficiencies for closed/open circuit were 82.1 ± 0.5% and 59.4 ± 3.3%, respectively. Cyclic voltammetry measurements demonstrated that the biocathode could efficiently catalyze nitrate reduction reaction. Autotrophic denitrification facilitated nitrogen removal using the electrode as electron donor. 16S rRNA-denaturing gradient gel electrophoresis (DGGE) was employed for community fingerprinting. At the biocathode the bacteria involved in nitrogen cycle predominated, of which the denitrifying bacteria were closely similar to Acidovorax sp. and/or Delftia sp. They were affiliated with the family Comamondaceae. The combination of rotating biological contactors with MFCs derives a promising opportunity for wastewater treatment with a low cost and high quality effluent.     

Diagnostic performance of salivary cortisol and serum osteocalcin measurements in patients with overt and subclinical Cushing's syndrome

ObjectiveThe cut-off value for salivary cortisol measurement for the diagnosis of Cushing's syndrome (CS) may depend both on the severity of the disease and the composition of control group. Therefore, we examined the utility of midnight salivary cortisol measurements in patients who were evaluated for signs and symptoms of CS or because they had adrenal incidentalomas. Because serum osteocalcin (OC) is considered as a sensitive marker of hypercortisolism, we also investigated whether OC could have a role in the diagnosis of CS.Patients and methodsEach of the 151 patients was included into one of the following groups: (A) overt CS (n = 23), (B) subclinical CS (n = 18), (C) inactive adrenal adenomas (n = 40), (D) patients without HPA disturbances (n = 70). Patients (C + D) were used as controls. Serum, salivary and urinary cortisol, and OC were measured by electrochemiluminescence immunoassay.ResultsGroup A had suppressed OC as compared to both group B and group (C + D). Serum and salivary cortisol concentrations showed strong negative correlations with OC in patients with overt CS. The areas under the curves of salivary and serum cortisol at 24:00 h (0.9790 and 0.9940, respectively) serum cortisol after low dose dexamethasone test (0.9930) and OC (0.9220) obtained from ROC aanalysis for the diagnosis of overt CS were not statistically different.ConclusionThis study confirms the usefulness of midnight salivary cortisol measurements in the diagnosis of overt CS in the everyday endocrinological praxis. Our results suggest that OC may have a role in the diagnosis of overt CS.     

Importance of IL-10 and IL-6 during chronic hepatitis c genotype-1 treatment and their relation with IL28B

This paper investigates serum levels of interleukin 10 (IL-10) and interleukin 6 (IL-6) in patients with chronic hepatitis C genotype 1 (CHC-GT1), the relation of each with clinical and virological characteristics, how they affect the response to combined therapy and their relation with the IL28B polymorphisms rs12979860. Serum level expression and the polymorphism of IL-10, IL-6 and IL28B were determined in 138 CHC-GT1 patients, treated with pegylated interferon/ribavirin (pegIFN-α/RBV) for 48 weeks, in the following samples: baseline, week-12 (during treatment) and week-72 (post-treatment). 77 patients (56%) presented Sustained Virological Response (SVR) and 61 (44%) were non-SVR. Multivariate logistic regression showed that age ? 40 years (aOR = 3.7, 95%CI = 1.5–8.9, P = 0.004), low activity of gamma glutamyl transferase (GGT) (aOR = 0.9, 95%CI = 0.98–0.99, P = 0.028), CC genotype of IL28B polymorphim (aOR = 2.7, 95%CI = 1.0–7.2, P = 0.044) and low IL-6 (aOR = 0.5, 95%CI = 0.3–1.0, P = 0.038) were predictor factors of virological response. In all patients, following treatment, IL-6 decreased at week-12 (P = 0.004) from baseline and had returned to basal values at week-72. Serum IL-10 concentration was significantly decreased at week-72 only in SVR patients (P ? 0.001). When patients were stratified by IL28B polymorphisms rs12979860 CC vs non-CC patients, a statistically significant decrease in IL-10 at week-72 in both groups was observed (P = 0.003 and P ? 0.001, respectively). None of the polymorphisms of IL-10 or IL-6 studied were associated with SVR.ConclusionsCC genotype of IL28B and low IL-6 serum concentration are factors associated independently with SVR. Moreover, decreased IL-10 at week-72 is associated with SVR in both CC and non-CC patients, and both factors are important to determine the effectiveness of treatment.     

A nylon membrane based amperometric biosensor for polyphenol determination

A nylon membrane based amperometric biosensor employing banana fruit polyphenol oxidase (PPO) is presented for polyphenol detection. Nylon membrane was first activated and then coupled with chitosan. PPO was covalently attached to this membrane through glutaraldehyde coupling. The membrane bioconjugate was characterized by scanning electron microscopy (SEM) and Fourier Transform Infrared (FTIR) study and then mounted onto Au electrode using parafilm to construct a working electrode. Once assembled along with Ag/AgCl as reference and Pt as auxiliary electrode, the biosensor gave optimum response within 15 s at pH 7.5 and 30 °C, when polarized at +0.4 V. The response (in mA) was directly proportional to polyphenol concentration in the range 0.2–400 μM. The lower detection limit of the biosensor was 0.2 μM. The biosensor was employed for determination of polyphenols in tea, beverages and water samples. The enzyme electrode showed 25% decrease in initial activity after 150 reuses over 6 months, when stored at 4 °C.     

Effects of different forms of olive cake on the performance and carcass quality of Awassi lambs

Effects of form of olive cake (OC) on growth performances and carcass quality were studied on forty-eight Awassi lambs. All lambs were male with an average body weight of 29.5 kg (S.D. = 2.3 kg) at the beginning of the experiment. Animals were randomly divided into four groups of 12 lambs each. Lambs in each group received individually corn–soybean meal (SBM) total mixed rations (TMRs). Rations were incorporated with a fixed amount (149 g/kg DM) of OC of different forms: crude OC, a product of the three centrifugation extraction procedure (control group), alkali treated, ensiled and pelleted. All rations were isonitrogenous and isocaloric. The growth experiment lasted 10 weeks. In the following week, all lambs were slaughtered. At termination of the experiment, lambs fed crude, alkali treated or ensiled OC rations consumed more feed and gained more weight (P<0.05) than those fed the pelleted OC. This same trend was found for the feed conversion (FC), carcass and empty body weights (EBWs). However, external (hide, head and feet, HHF) and thoracic organs (heart and lungs, HL), gut and liver weights proportional to EBW (g/kg) were not affected by the form of OC. The form of OC had no effects on muscle (P=0.4) and bone (P=0.21) tissues. Carcass, pelvic, kidney fats and total carcass fats weights when expressed as g/kg EBW and the percent of carcass fat of total body fat (TBF) were lower in lambs fed the pelleted OC compared to those offered the other forms of OC. However, the subcutaneous, inter muscular and TBF fats weights (g/kg) were comparable among lambs in different OC form rations. Results from this work suggest that the treated OC had no advantages compared to crude in regard to parameters investigated in this research.     

Development of electrochemical sulfite biosensor based on SOX/PBNPs/PPY modified Au electrode

A sulfite oxidase (SO_X) (EC 1.8.3.1) purified from Syzygium cumini leaves was immobilized onto Prussian blue nanoparticles/polypyrrole (PBNPs/PPY) nanocomposite film electrodeposited onto the surface of gold (Au) electrode. An electrochemical sulfite biosensor was fabricated using SO_X/PBNPs/PPY/Au electrode as working electrode, Ag/AgCl as standard electrode and Pt wire as auxiliary electrode connected through a potentiostat. The working electrode was characterized by Fourier Transform infrared (FTIR) spectroscopy, cyclic voltammetry (CV), scanning electron microscopy (SEM) and electrochemical impedance spectroscopy (EIS) at different stages of its construction. The biosensor showed optimum response within 2 s, when operated at 20 mV s⁻¹ in 0.1 M Tris–HCl buffer, pH 8.0 and at 30 °C. Linear range and minimum detection limit were 0.5–1000 μM and 0.1 μM (S/N = 3) respectively. The sensor was evaluated with 95.0% recovery of added sulfite in red wine samples and 1.9% and 3.3% within and between batch coefficients of variation respectively. There was a good correlation (r = 0.96) between red wine samples sulfite value by standard DTNB method and the present method. The sensor was employed for determination of sulfite level in red, white and rose wine samples. The enzyme electrode was used 300 times over a period of 4 months, when stored at 4 °C.     

Microfiltration membrane performance in two-chamber microbial fuel cells

Proton exchange membranes (PEMs) are typically used in two-chamber microbial fuel cells (MFCs) to separate the anode and cathode chambers while allowing protons to pass between the chambers. However, PEMs such as Nafion are not cost-effective. To reduce the cost of MFCs, we examined the performances of cellulose acetate microfiltration membranes in a two-chamber microbial fuel cell using acetate. The internal resistance, the maximum power density and the coulombic efficiency (CE) of the microfiltration membrane MFC (MMMFC) were 263 Ω, 0.831 ± 0.016 W/m² and 38.5 ± 3.5%, respectively, in a fed-batch mode, while the corresponding values of the MFC using a PEM were 267 Ω, 0.872 ± 0.021 W/m² and 74.7 ± 4.6%, respectively. We further used the MMMFC for poultry wastewater treatment. The maximum power density of 0.746 ± 0.024 W/m² and CE of 35.3 ± 3.2% were achieved when the poultry wastewater containing 566 mg/L COD was used, removing 81.6 ± 6.6% of the COD. These results demonstrate microfiltration membranes, compared with PEMs, have a similar internal resistance and reduce pH gradient across the membrane. They parallel PEMs in maximum power density, while CE is much lower due to the oxygen and substrate diffusion. The MMMFC was effective for poultry wastewater treatment with high COD removal.