Simulated hip abductor strengthening reduces peak joint contact forces in patients with total hip arthroplasty

Lower extremity muscle strength training is a focus of rehabilitation following total hip arthroplasty (THA). Strength of the hip abductor muscle group is a predictor of overall function following THA. The purpose of this study was to investigate the effects of hip abductor strengthening following rehabilitation on joint contact forces (JCFs) in the lower extremity and low back during a high demand step down task. Five THA patients performed lower extremity maximum isometric strength tests and a stair descent task. Patient-specific musculoskeletal models were created in OpenSim and maximum isometric strength parameters were scaled to reproduce measured pre-operative joint torques. A pre-operative forward dynamic simulation of each patient performing the stair descent was constructed using their corresponding patient-specific model to predict JCFs at the ankle, knee, hip, and low back. The hip abductor muscles were strengthened with clinically supported increases (0–30%) above pre-operative values in a probabilistic framework to predict the effects on peak JCFs (99% confidence bounds). Simulated hip abductor strengthening resulted in lower peak JCFs relative to pre-operative for all five patients at the hip (18.9–23.8 ± 16.5%) and knee (20.5–23.8 ± 11.2%). Four of the five patients had reductions at the ankle (7.1–8.5 ± 11.3%) and low back (3.5–7.0 ± 5.3%) with one patient demonstrating no change. The reduction in JCF at the hip joint and at joints other than the hip with hip abductor strengthening demonstrates the dynamic and mechanical interdependencies of the knee, hip and spine that can be targeted in early THA rehabilitation to improve overall patient function.     

Effect of hip flexion angle on stiffness of the adductor longus muscle during isometric hip flexion

This study examined the effect of hip flexion angle on the stiffness of the adductor longus (AL) muscle during isometric hip flexion. Seventeen men were recruited. Ten participants performed submaximal voluntary contraction at 0%, 25%, 50%, and 75% of maximal voluntary contraction (MVC) during isometric hip flexion after performing MVC at 0°, 40°, and 80° of hip flexion. Seven participants performed submaximal voluntary tasks during isometric hip extension in addition to hip flexion task. The shear modulus of the AL muscle was used as the index of muscle stiffness, and was measured using ultrasound shear-wave elastography during the tasks at each contraction intensity for each hip flexion angle. During hip flexion, the shear modulus of the AL muscle was higher at 0° than at 40° and 80° of hip flexion at each contraction intensity (p < 0.016). Conversely, a significant effect was not found among hip flexion angle during hip extension at 75% of MVC (p = 0.867). These results suggest that mechanical stress of the AL muscle may be higher at 0° of hip flexion during isometric hip flexion.     

The influence of muscle activation on impact dynamics during lateral falls on the hip

Muscle activation has been demonstrated to influence impact dynamics during scenarios including running, automotive impacts, and head impacts. This study investigated the effects of targeted muscle activation magnitude on impact dynamics during low energy falls on the hip with human volunteers. Fifteen university-aged participants (eight females, seven males) underwent 12 lateral pelvis release trials. Half of the trials were muscle-‘relaxed’; in the remaining ‘contracted’ trials participants isometrically contracted their gluteus medius to 20–30% of maximal voluntary contraction before the drop was initiated onto a force plate. Peak force applied to the femur-pelvis complex averaged 9.3% higher in contracted compared to relaxed trials (F = 6.798, p = .022). Muscle activation effects were greater for females, resulting in (on average) an 18.5% increase in effective pelvic stiffness (F = 5.838, p = .046) and a 23.4% decrease in time-to-peak-force (F = 5.109, p = .042). In the relaxed trials, muscle activation naturally increased during the impact event, reaching levels of 12.8, 7.5, 11.1, and 19.1% MVC at the time of peak force for the gluteus medias, vastus lateralis, erector spinae, and external oblique, respectively. These findings demonstrated that contraction of trunk and hip musculature increased peak impact force across sexes. In females, increases in the magnitude and rate of loading were accompanied (and likely driven) by increases in system stiffness. Accordingly, incorporating muscle activation contributions into biomechanical models that investigate loading dynamics in the femur and/or pelvis during lateral impacts may improve estimate accuracy.     

Hip joint muscle forces during gait in patients with femoroacetabular impingement syndrome are associated with patient reported outcomes and cartilage composition

Femoroacetabular impingement syndrome (FAIS) consists of abnormal hip joint morphology and pain during activities of daily living. Abnormal gait mechanics and potentially abnormal muscle forces within FAI patients leads to articular cartilage damage. Therefore, there is a necessity to understand the effects of FAI on hip joint muscle forces during gait and the link between muscle forces, patient reported outcomes (PRO) and articular cartilage health. The purposes of this study were to assess: (1) hip muscle forces between FAI patients and healthy controls and (2) the associations between hip muscle forces with PRO and cartilage composition (T_1ρ/T₂ mapping) within FAI patients. Musculoskeletal simulations were used to estimate peak muscle forces during the stance phase of gait in 24 FAI patients and 24 healthy controls. Compared to controls, FAI patients ambulated with lower vasti (30% body-weight, p = 0.01) and higher sartorius (4.0% body-weight, p < 0.01) forces. Within FAI patients, lower peak gluteus medius, gluteus minimus, sartorius and iliopsoas forces were associated with worse hip joint pain and function (R = 0.43–0.70, p = 0–0.04), while lower muscle forces were associated with increased T_1ρ and T₂ values (i.e. altered cartilage composition) within the hip joint cartilage (R = −0.44 to −0.58, p = 0.006–0.05). Although FAI patients demonstrate abnormal muscle forces, it is unknown whether or not these altered muscle force patterns are associated with pain avoidance or weak musculature. Further investigation is required in order to better understand the effects of FAI on hip joint muscle forces and the associations with hip joint cartilage degeneration.     

Effects of body configuration on pelvic injury in backward fall simulation using 3D finite element models of pelvis–femur–soft tissue complex

Injuries due to backward fall apart from sideways fall are a major health problem, particularly among the aged populations. The objectives of this study was to evaluate the responses to changing body configurations (angle between the trunk and impacting floor as 0°, 15°, 45° and 80°) during backward fall, based on a previously developed CT-scan-derived 3D non-linear and non-homogeneous finite element (FE) model of pelvis–femur–soft tissue complex with simplified biomechanical representation of the whole body. Under constant impact energy, these FE models evaluated the pelvic injury situations on the basis of peak impact force (7.64–16.74 kN) and peak principal compressive strain (more than 1.5%), consistent with the clinically observed injuries (sacral insufficiency, coccydynia). Also the change in location of peak strain and increase in peak impact force for changing configurations from 0° to 80° indicated the effect of whole body inertia during backward fall. It was also concluded that the inclusion of sacro-iliac and acetabular cartilages in the above FE models will further reduce above findings marginally (9.2% for 15° fall). These quantifications would also be helpful for a better design and development of safety structures such as safety floor for the nursing home or home for the aged persons.     

Pelvis and femur geometry: Relationships with impact characteristics during sideways falls on the hip

While metrics of pelvis and femur geometry have been demonstrated to influence hip fracture risk, attempts at linking geometry to underlying mechanisms have focused on fracture strength. We investigated the potential effects of femur and pelvis geometry on applied loads during lateral falls on the hip. Fifteen female volunteers underwent DXA imaging to characterize two pelvis and six femur geometric features. Additionally, participants completed low-energy sideways falls on the hip; peak impact force and pressure, contact area, and moment of force applied to the proximal femur were extracted. No geometric feature was significantly associated with peak impact force. Peak moment of force was significantly associated with femur moment arm (p = 0.005). Peak pressure was positively correlated with pelvis width and femur moment arm (p < 0.05), while contact area was negatively correlated with metrics of pelvis width and femur neck length (p < 0.05). This is the first study to link experimental measures of impact loads during sideways falls with image-based skeletal geometry from human volunteers. The results suggest that while skeletal geometry has limited effects on overall peak impact force during sideways falls, it does influence how impact loads are distributed at the skin surface, in addition to the bending moment applied to the proximal femur. These findings have implications for the design of protective interventions (e.g. wearable hip protectors), and for models of fall-related lateral impacts that could incorporate the relationships between skeletal geometry, external load magnitude/distribution, and tissue-level femur loads.     

Variables during swing associated with decreased impact peak and loading rate in running

When the foot impacts the ground in running, large forces and loading rates can arise that may contribute to the development of overuse injuries. Investigating which biomechanical factors contribute to these impact loads and loading rates in running could assist clinicians in developing strategies to reduce these loads. Therefore, the goals of our work were to determine variables that predict the magnitude of the impact peak and loading rate during running, as well as to investigate how modulation of knee and hip muscle activity affects these variables. Instrumented gait analysis was conducted on 48 healthy subjects running at 3.3 m/s on a treadmill. The top four predictors of loading rate and impact peak were determined using a stepwise multiple linear regression model. Forward dynamics was performed using a whole body musculoskeletal model to determine how increased muscle activity of the knee flexors, knee extensors, hip flexors, and hip extensors during swing altered the predictors of loading rate and impact peak. A smaller impact peak was associated with a larger downward acceleration of the foot, a higher positioned foot, and a decreased downward velocity of the shank at mid-swing while a lower loading rate was associated with a higher positioned thigh at mid-swing. Our results suggest that an alternative to forefoot striking may be increased hip flexor activity during swing to alter these mid-swing kinematics and ultimately decrease the leg's velocity at landing. The decreased velocity would decrease the downward momentum of the leg and hence require a smaller force at impact.     

Influence of weak hip abductor muscles on joint contact forces during normal walking: probabilistic modeling analysis

The weakness of hip abductor muscles is related to lower-limb joint osteoarthritis, and joint overloading may increase the risk for disease progression. The relationship between muscle strength, structural joint deterioration and joint loading makes the latter an important parameter in the study of onset and follow-up of the disease. Since the relationship between hip abductor weakness and joint loading still remains an open question, the purpose of this study was to adopt a probabilistic modeling approach to give insights into how the weakness of hip abductor muscles, in the extent to which normal gait could be unaltered, affects ipsilateral joint contact forces. A generic musculoskeletal model was scaled to each healthy subject included in the study, and the maximum force-generating capacity of each hip abductor muscle in the model was perturbed to evaluate how all physiologically possible configurations of hip abductor weakness affected the joint contact forces during walking. In general, the muscular system was able to compensate for abductor weakness. The reduced force-generating capacity of the abductor muscles affected joint contact forces to a mild extent, with 50th percentile mean differences up to 0.5 BW (maximum 1.7 BW). There were greater increases in the peak knee joint loads than in loads at the hip or ankle. Gluteus medius, particularly the anterior compartment, was the abductor muscle with the most influence on hip and knee loads. Further studies should assess if these increases in joint loading may affect initiation and progression of osteoarthritis.     

Biomechanical comparison of implant inclinations and load times with the all-on-4 treatment concept: a three-dimensional finite element analysis

The purpose of this study was to compare the effects of implant inclinations and load times on stress distributions in the peri-implant bone based on immediate- and delayed-loading models. Four 3D FEA models with different inclination angle of the posterior implants (0°, 15°, 30°, 45°) were constructed. A static load of 150?N in the multivectoral direction was applied unilaterally to the cantilever region. The stress distributions in the peri-implant bone were evaluated before and after osseointegration. The principal tensile stress (σ_max), mean principal tensile stress (σ_max), principal compressive stress (σ_min) and mean principal compressive stress (σ_min) of the bone and micromotion at the contact interface between the bone and implants were calculated. In all the models, peak principal stresses occurred in the bone surrounding the left tilted implant. The highest σ_max and σ_min were all observed in the 0° model for both immediate- and delayed-loading models. And the 0° and 15° models showed higher σ_max and σ_min values. The 0°models showed the largest micromotion. The observed stress distribution was better in the 30° and 45° models than in the 0° and 15° models.     

Effect of pre-impact movement strategies on the impact forces resulting from a lateral fall

Approximately 90% of hip fractures in older adults result from falls, mostly from landing on or near the hip. A three-dimensional, 11-segment, forward dynamic biomechanical model was developed to investigate whether segment movement strategies prior to impact can affect the impact forces resulting from a lateral fall. Four different pre-impact movement strategies, with and without using the ipsilateral arm to break the fall, were implemented using paired actuators representing the agonist and antagonist muscles acting about each joint. Proportional-derivative feedback controller controlled joint angles and velocities so as to minimize risk of fracture at any of the impact sites. It was hypothesized that (a) the use of active knee, hip and arm joint torques during the pre-contact phase affects neither the whole body kinetic energy at impact nor the peak impact forces on the knee, hip or shoulder and (b) muscle strength and reaction time do not substantially affect peak impact forces. The results demonstrate that, compared with falling laterally as a rigid body, an arrest strategy that combines flexion of the lower extremities, ground contact with the side of the lower leg along with an axial rotation to progressively present the posterolateral aspects of the thigh, pelvis and then torso, can reduce the peak hip impact force by up to 56%. A 30% decline in muscle strength did not markedly affect the effectiveness of that fall strategy. However, a 300-ms delay in implementing the movement strategy inevitably caused hip impact forces consistent with fracture unless the arm was used to break the fall prior to the hip impact.     

Soft tissue stiffness over the hip increases with age and its implication in hip fracture risk in older adults

Risk of hip fracture depends on the bone strength as well as the impact force delivered to the proximal femur during falls, and femoral soft tissue may help to reduce the hip fracture risk by attenuating the impact force. Femoral soft tissue stiffness was measured from a large sample, and compared how this was affected by age, gender and site.One hundred fifty healthy individuals (fifty-two young (aged between 19 and 29), forty-eight middle-aged (30–64), and fifty old (over 65)) participated. Each age group included an equal number of males and females. Using an automated hand-held indentation device, soft tissue stiffness was measured over twelve sites with respect to the greater trochanter (GT).For both left and right hips, the stiffness was associated with age (p < 0.0005), gender (p < 0.0005), and site (p < 0.0005). On average, the stiffness was 26% greater in older than young adults (321.5 versus 254.3 N/m). On average across twelve sites, the regression analysis indicated that the stiffness increases 1.33 N/m every year (“soft tissue stiffness over the hip = 1.33*age + 221.8”; R = 0.518, p < 0.0005). Furthermore, the stiffness was 18% greater in male than female (308.8 versus 262.6 N/m), and differed across twelve sites over the hip, being greatest (424.2 N/m) at the GT, and least (206.3 N/m) at the superior gluteal region.The results provide insights into the shock absorbing property of soft tissue over the hip, and inform the improvement of fall-related injury prevention interventions (i.e., hip protector, safe landing strategies) in older adults.     

The application of musculoskeletal modeling to investigate gender bias in non-contact ACL injury rate during single-leg landings

The central tenet of this study was to develop, validate and apply various individualised 3D musculoskeletal models of the human body for application to single-leg landings over increasing vertical heights and horizontal distances. While contributing to an understanding of whether gender differences explain the higher rate of non-contact anterior cruciate ligament (ACL) injuries among females, this study also correlated various musculoskeletal variables significantly impacted by gender, height and/or distance and their interactions with two ACL injury-risk predictor variables; peak vertical ground reaction force (VGRF) and peak proximal tibia anterior shear force (PTASF). Kinematic, kinetic and electromyography data of three male and three female subjects were measured. Results revealed no significant gender differences in the musculoskeletal variables tested except peak VGRF (p = 0.039) and hip axial compressive force (p = 0.032). The quadriceps and the gastrocnemius muscle forces had significant correlations with peak PTASF (r = 0.85, p < 0.05 and r = ? 0.88, p < 0.05, respectively). Furthermore, hamstring muscle force was significantly correlated with peak VGRF (r = ? 0.90, p < 0.05). The ankle flexion angle was significantly correlated with peak PTASF (r = ? 0.82, p < 0.05). Our findings indicate that compared to males, females did not exhibit significantly different muscle forces, or ankle, knee and hip flexion angles during single-leg landings that would explain the gender bias in non-contact ACL injury rate. Our results also suggest that higher quadriceps muscle force increases the risk, while higher hamstring and gastrocnemius muscle forces as well as ankle flexion angle reduce the risk of non-contact ACL injury.     

Effect of hip joint angle on concentric knee extension torque

This study tested the hypothesis that the effect of hip joint angle on concentric knee extension torque depends on knee joint angle during a single knee extension task. Twelve men performed concentric knee extensions in fully extended and 80° flexed hip positions with maximal effort. The angular velocities were set at 30° s⁻¹ and 180° s⁻¹. The peak torque and torques attained at 30°, 50°, 70° and 90° (anatomical position = 0°) of the knee joint were compared between the two hip positions. Muscle activations of the vastus lateralis, medialis, rectus femoris and biceps femoris were determined using surface electromyography. The peak torque was significantly greater in the flexed than in the extended hip position irrespective of angular velocity. The torques at 70° and 90° of the knee joint at both angular velocities and at 50° at 180° s⁻¹ were significantly greater in the flexed than in the extended hip position, whereas corresponding differences were not found at 30° (at either angular velocity) and 50° (at 30° s⁻¹) of the knee joint. No effect of hip position on muscle activation was observed in any muscle. These results supported our hypothesis and may be related to the force–length and force–velocity characteristics of the rectus femoris.     

Statistical shape modelling versus linear scaling: Effects on predictions of hip joint centre location and muscle moment arms in people with hip osteoarthritis

Marker-based dynamic functional or regression methods are used to compute joint centre locations that can be used to improve linear scaling of the pelvis in musculoskeletal models, although large errors have been reported using these methods. This study aimed to investigate if statistical shape models could improve prediction of the hip joint centre (HJC) location. The inclusion of complete pelvis imaging data from computed tomography (CT) was also explored to determine if free-form deformation techniques could further improve HJC estimates. Mean Euclidean distance errors were calculated between HJC from CT and estimates from shape modelling methods, and functional- and regression-based linear scaling approaches. The HJC of a generic musculoskeletal model was also perturbed to compute the root-mean squared error (RMSE) of the hip muscle moment arms between the reference HJC obtained from CT and the different scaling methods. Shape modelling without medical imaging data significantly reduced HJC location error estimates (11.4 ± 3.3 mm) compared to functional (36.9 ± 17.5 mm, p = <0.001) and regression (31.2 ± 15 mm, p = <0.001) methods. The addition of complete pelvis imaging data to the shape modelling workflow further reduced HJC error estimates compared to no imaging (6.6 ± 3.1 mm, p = 0.002). Average RMSE were greatest for the hip flexor and extensor muscle groups using the functional (16.71 mm and 8.87 mm respectively) and regression methods (16.15 mm and 9.97 mm respectively). The effects on moment-arms were less substantial for the shape modelling methods, ranging from 0.05 to 3.2 mm. Shape modelling methods improved HJC location and muscle moment-arm estimates compared to linear scaling of musculoskeletal models in patients with hip osteoarthritis.     

Biomechanical strategies for successful obstacle crossing with the trailing limb in older adults with medial compartment knee osteoarthritis

To investigate the biomechanical strategy adopted by older adults with medial compartment knee osteoarthritis (OA) for successful obstacle crossing with the trailing limb, and to discuss its implications for fall-prevention, 15 older adults with bilateral medial compartment knee OA and 15 healthy controls were recruited to walk and cross obstacles of heights of 10%, 20%, and 30% of their leg lengths. Kinematic and kinetic data were obtained using a three-dimensional (3D) motion analysis system and forceplates. The OA group had higher trailing toe clearance than the controls. When the trailing toe was above the obstacle, the OA group showed greater swing hip abduction, yet smaller stance hip adduction, knee flexion, and ankle eversion. They showed greater pelvic anterior tilt and toe-out angle. They also exhibited greater peak knee abductor moments during early stance and at the instant when the swing toe was above the obstacle, while a greater peak hip abductor moment was found during late stance. Smaller knee extensor, yet greater hip extensor moments, were found in the OA group throughout the stance phase. In order to achieve higher toe clearance with knee OA, particular joint kinematic and kinetic strategies have been adopted by the OA group. Weakness in the hip abductors and extensors in individuals with OA may be risk factors for tripping owing to the greater demands on these muscle groups during obstacle crossing by these individuals.     

Hip-joint and abductor-muscle forces adequately represent in vivo loading of a cemented total hip reconstruction.

Using finite element analyses, we investigated which muscle groups acting around the hip-joint most prominently affected the load distributions in cemented total hip reconstructions with a bonded and debonded femoral stem. The purpose was to determine which muscle groups should be included in pre-clinical tests, predicting bone adaptation and mechanical failure of cemented reconstructions, ensuring an adequate representation of in vivo loading of the reconstruction. Loads were applied as occurring during heel-strike, mid-stance and push-off phases of gait. The stress/strain distributions within the reconstruction, produced by the hip-joint contact force, were compared to ones produced after sequentially including the abductors, the iliotibial tract and the adductors and vastii. Inclusion of the abductors had the most pronounced effect. They neutralized lateral bending of the reconstruction at heel-strike and increased medial bending at mid-stance and push-off. Bone strains and stem stresses were changed accordingly. Peak tensile cement stresses were reduced during all gait phases by amounts up to 50% around a bonded stem and 11% around a debonded one. Additional inclusion of the iliotibial tract, the adductors and the vastii produced relatively small effects during all gait phases. Their most prominent effect was a slight reduction of bone strains at the level of the stem tip during heel-strike. These results suggest that a loading configuration including the hip-joint contact force and the abductor forces can adequately reproduce in vivo loading of cemented total hip reconstructions in pre-clinical tests.     

Normal hip joint contact pressure distribution in single-leg standing--effect of gender and anatomic parameters.

A practical and easy-to-use analysis technique that can study the patient's hip joint contact force/pressure distribution would be useful to assess the effect of abnormal biomechanical conditions and anatomical deformities on joint contact stress for treatment planning purpose. This technique can also help to establish the normative database on hip joint contact pressure distribution in men and women in different age groups. Twelve anatomic parameters and seven biomechanical parameters of the hip joint in a normal population (41 females, 15 males) were calculated. The inter-parameter correlations were investigated. The pressure distribution in the hip joint was calculated using a three-dimensional discrete element analysis (DEA) technique. The 3D contact geometry of the hip joint was estimated from a 2D radiograph by assuming that the femoral head and the acetabular surface were spherical in shape. The head-trochanter ratio (HT), femoral head radius, pelvic height, the joint contact area, the normalized peak contact pressure, abductor force, and the joint contact force were significantly different between men and women. The normalized peak contact pressure was correlated both with acetabular coverage and head-trochanter ratio. Change of abductor force direction within normal variation did not affect the joint peak contact pressure. However, in simulated dysplastic conditions when the CE angle is small or negative, abductor muscle direction becomes very sensitive in joint contact pressure estimation. The models and the results presented can be used as the reference base in computer simulation for preoperative planning in pelvic or femoral osteotomy.     

The effect of positioning on the biomechanical performance of soft shell hip protectors

Wearable hip protectors represent a promising strategy for reducing risk for hip fracture from a sideways fall. However, small changes in pad positioning may influence their protective benefit. Using a mechanical hip impact simulator, we investigated how three marketed soft shell hip protectors attenuate and redistribute the impact force applied to the hip, and how this depends on displacement from their intended position by 2.5 or 5 cm superiorly, posteriorly, inferiorly or anteriorly. For centrally-placed protectors, peak pressure was reduced 93% below the unpadded value by a 16 mm horseshoe-shaped protector, 93% by a 14 mm horseshoe protector, and 94% by a 16 mm continuous protector. In unpadded trials, 83% of the total force was applied to the skin overlying the proximal femur (danger zone). This was lowered to 19% by the centrally placed 16 mm horseshoe protector, to 34% by the 14 mm horseshoe, and to 40% by the 16 mm continuous protector. Corresponding reductions in peak force delivered to the femoral neck (relative to unpadded) were 45%, 38%, and 20%, respectively. The protective benefit of all three protectors decreased with pad displacement. For example, displacement of protectors by 5 cm anteriorly caused peak femoral neck force to increase 60% above centrally-placed values, and approach unpadded values. These results indicate that soft shell hip protectors provide substantial protective benefits, but decline in performance with small displacements from their intended position. Our findings confirm the need for correct and stable positioning of hip protectors in garment design.     

Energy absorption during impact on the proximal femur is affected by body mass index and flooring surface

Impact mechanics theory suggests that peak loads should decrease with increase in system energy absorption. In light of the reduced hip fracture risk for persons with high body mass index (BMI) and for falls on soft surfaces, the purpose of this study was to characterize the effects of participant BMI, gender, and flooring surface on system energy absorption during lateral falls on the hip with human volunteers. Twenty university-aged participants completed the study with five men and five women in both low BMI (<22.5 kg/m²) and high BMI (>27.5 kg/m²) groups. Participants underwent lateral pelvis release experiments from a height of 5 cm onto two common floors and four safety floors mounted on a force plate. A motion-capture system measured pelvic deflection. The energy absorbed during the initial compressive phase of impact was calculated as the area under the force–deflection curve. System energy absorption was (on average) 3-fold greater for high compared to low BMI participants, but no effects of gender were observed. Even after normalizing for body mass, high BMI participants absorbed 1.8-fold more energy per unit mass. Additionally, three of four safety floors demonstrated significantly increased energy absorption compared to a baseline resilient-rolled-sheeting system (% increases ranging from 20.7 to 28.3). Peak system deflection was larger for high BMI persons and for impacts on several safety floors. This study indicates that energy absorption may be a common mechanism underlying the reduced risk of hip fracture for persons with high BMI and for those who fall on soft surfaces.     

Fall arrest strategy affects peak hand impact force in a forward fall

We measured the peak hand impact force involved in bimanually arresting a forward fall to the ground from a 1-m shoulder height in five healthy young males. The effects of three different subject instruction sets: "arrest the fall naturally"; "keep the head as far from the ground as possible"; and "minimize the peak hand forces" were studied by measuring body segment kinematics, ground reaction forces, and upper-extremity myoelectric activity. The hypotheses were tested that the (a) arrest strategy did not influence peak impact force, (b) arm configuration, impact velocity and upper-extremity electromyography (EMG) levels correlate to the peak impact force (c) and impacting the ground with one hand leading the other does not increase the impact force over that obtained with simultaneous hand use. The results show that these subjects were able to volitionally decrease the peak impact force at the wrist by an average of 27% compared with a "natural landing" (p=0.014) and 40% compared with a "stiff-arm landing" (p<0.0005). The magnitude of the peak unilateral wrist force varied from 0.65 to 1.7 body weight for these moderate falls onto a padded surface. Peak force correlated with the elbow angle at impact, wrist velocity at impact and with pre-EMG triceps activity. The force was not significantly higher for non-simultaneous hand impacts. We conclude that fall arrest strategy can substantially alter the peak impact forces applied to the distal forearm during a fall arrest. Therefore, the fall arrest strategy likely influences wrist injury risk independent of bone strength.